Search Documents

By G. Morin, S. Amira, F. Chiesa, B. Duchesne

"The effect of heat treatment on the stress corrosion cracking (SCC) resistance of A206 aluminum alloy was studied using the breaking load test according to ASTM G139 standard. This method uses the residual strength measurement from tensile test specimens previously stressed axially while exposed to the 3.5% NaCl alternate immersion test according to ASTM G44 standard. The residual strength after exposure is used as a measure of SCC degradation. The performed heat treatments were conventional natural aging T4 and artificial over-aging T7 tempers in addition to artificial aging T6 temper added for purpose of comparison. These tests showed that A206-T4 has a good resistance to SCC at pre-loads up to 100 MPa while A206-T7 was prone to SCC for pre-loads of 0 and 50 MPa, and showed total loss of ductility for pre-load of 100 MPa. Both A206-T4 and A206-T7 pre-loaded at 150 MPa showed poor resistance to SCC. A206-T6 showed the worst susceptibility to SCC as it lost all mechanical resistance at the end of the alternate exposure to 3.5% NaCl solution, even without any applied pre-load. Metallographic analyses showed that the resistance of A206 alloy to SCC is mainly affected by the transition from pitting to intergranular corrosion attack. The initiation and the propagation of intergranular corrosion attack might be assisted by high stress concentrations in the pits, particularly for pre-loads higher than 100 MPa. The transition from pitting to intergranular corrosion can also be promoted by hydrogen evolution from growing pits, which supports crack propagation by hydrogen embrittlement.INTRODUCTIONA206 aluminum-copper casting alloy offers ones of the best mechanical properties among the aluminum foundry alloys. This alloy belongs to the 206 alloy family developed in 1970s as an alternative to the highly resistant and ductile but more expensive Ag containing 201 alloy (Tiryakioglu, 2009). A206 showed also good low cycle fatigue strength (Sigworth, 2002). These properties made A206 alloy a strong candidate for some vehicles lightweighting applications. In spite of its interesting properties cited above, A206 alloy was rarely used in critical applications due to its tendency for hot tearing and stress corrosion cracking (SCC). Studies of A206 hot tearing behavior showed that this tendency can be reduced by improving castability and by grain refinement (Sigworth, 2002). The optimisation of the casting design can also prevent the tendency toward hot tearing. The SCC of aluminum-copper alloys arises from their susceptibility to localised corrosion, especially in chloride containing media. The localised corrosion in Al-Cu alloys is caused mainly by their heterogeneous microstructure, where the presence of many phases leads to the formation of micro-galvanic coupling with the matrix. However, most of the studies aimed at investigate the SCC of Al-Cu alloys concerned the wrought ones, especially the AA2024 alloy tempered in the T3 (or derivative) condition and few studies concerned the 206 and cast alloys in general (Alexopoulos, 2009 and 2016; Campestrini, 2000; Vogt, 1998; Talamantes-Silva, 2008; Zhang, 2003). Jean et al. (Jean, 2009) studied the effect of heat treatment on SCC behavior of B206 alloy using alternate immersion technique and grain boundary attack method and did not find direct correlation between the two methods. Another study showed that aging of 206 alloy may make a casting susceptible to SCC (Sigworth, 2002). However, these studies did not provide detailed information about the mechanisms of SCC of 206 alloy, as well as the effect of the stress intensity. The present work investigates the effect heat treatments and the stress intensity on the morphology of the corrosion attack and the SCC behavior A206 aluminum alloy. This study uses the breaking load test according to ASTM G139. This test utilizes direct tensile specimens and was developed to give a more quantitative measure of the SCC performance of resistant aluminum"

Jan 1, 2016

By C. G. Anderson

Alkaline sulfide leaching technology (i.e. ASL) has been studied, presented and published throughout the literature and utilized in some current engineering studies. Yet, the actual industrial applications are very few and the knowledge about these is very limited. Hence, a large gap between the laboratory, publications, engineering studies, and the actual industrial plant exists. Recent studies of ASL applied to copper enargite concentrates definitively bear out this dichotomy. Hence, this paper will seek to dispel the common misperceptions that continue to surround the selective industrial ASL hydrometallurgical technology. For edification of the reader, a listing of ten common misconceptions and myths is listed. As well, ASL history, fundamental aspects and a new flowsheet application for simultaneous gold and high purity antimony oxide production from low grade materials is included. The associated estimated economic considerations are also included to heighten enlightenment about the application of this industrially proven technology.

Jan 1, 2014

By G. N. Nnadi, R. J. Mitchell

"The response of cemented backfills subjected to simulated blast loadings is studied using centrifugal modelling techniques. Scaling requirements for centrifugal modelling are developed and the results of the similitude analysis show that an acceleration field is required to capture the true dynamic response of backfill models. Experiments have been conducted at various centrifugal accelerations. The effects of ring blasting were simulated by an impact loading on the exposed fill face. The behaviour of the cemented backfill was monitored with accelerometers as well as dynamic stress gauges.Cemented backfill response to impact loadings was found to depend strongly on simulated gravitational stress level. Results also show that the characteristics of the response changes with distance from the impact. Finally, the results of the models were used to predict prototype peak accelerations, velocities and displacements. The results reported in this study indicate that centrifuge modelling may be a useful tool for dynamic studies of blast damage to backfills. Centrifuge modelling can be carried out at low costs and can be used to design prototype instrumentation systems. IntroductionThe response of cemented mine backfills to blast loadings is of concern to the mining industry because these backfills provide local and regional support during ore pillar extraction. Considerable research has been reported on the static stability (Smith et al., 1983) and on effects of reinforcements on cemented backfills (Mitchell, 1989). However, information regarding dynamic aspects of cemented backfill is limited. O'Hearn and Swan (1989) reported on the response of cemented backfill to blast loading, but these blasts were not very dose to the backfill . A schematic representation of a rock-backfill system is shown in Figure I.The mechanics of transfer of explosive energy to rock and subsequently to the backfill, and the resulting responses, are complex. Achison (1968) listed more than twenty factor s affecting the blast fragmentation of rock and grouped these into the categories of explosive parameters, charge parameters and rock parameters. Although significant advances have been made, during the past two decades, in understanding the mechanics of blasting, the degree of uncertainty associated with predicting the behaviour of backfills subjected to dynamic loadings makes the application of simple design safety factors insufficient. Comprehensive testing programs or prototype instrumentation is required to evaluate the risks associated with blast or earthquake loadings on backfill."

Jan 1, 1991

By M. R. Henzinger, G. Lenz, A. Gaich, Pötsch, W. Schubert, P. Wagner

"The better the information on the rock mass and its fracture system, the better is the basis for any rock mechanical decision that is required during the excavation process. While in conventional tunnelling free view to the tunnel face is available, possibilities are limited for mechanised tunnelling using a tunnel boring machine (TBM). An approach, already formulated in 2005, is used that produces digital photographs through openings in the cutting wheel of a TBM and merges them into a circular three-dimensional image. The 3D image is then used for geometric rock mass characterisation purposes including geological mapping, for example to measure spatial orientations or determine joint spacing. In the paper the basic concept is described together with first results from a pilot test.INTRODUCTIONA three-dimensional image unites digital photographs with spatial information on the objects/surfaces it shows. Since they combine geometric and visual information they are a straightforward source for geometric rock mass analysis and geological mapping. Their obvious benefits among others are: (i) they allow spatial measurements even in inaccessible regions, (ii) they provide objective and reproducible records of the rock mass conditions, and (iii) they increase working safety (Gaich et al. 2004).Pre-requisite for the generation of 3D images is the acquisition of at least two photographs from the region of interest. From the photographs the imaged object surfaces are reconstructed by means of image analysis using methods from photogrammetry (Slama, 1980) and computer vision (Hartley & Zisserman, 2001). See also Figure 1."

Jan 1, 2015

By Raj Thamburaj

"Over the last few decades, the emphasis on affordability and reduced cost of ownership has necessitated the development of innovative processes to carry out repairs in aero engine components. Conventional weld and braze repairs have evolved into advanced, sophisticated processes using state of the art knowledge in lasers, robotics and materials technology. This paper illustrates past and present scenarios in an attempt to illustrate progress that has been made in this area. The problems encountered in the past have been detailed along with the solutions that have been developed and commercially implemented to address these issues. Apart from technical progress, this presentation also addresses the progress made in business approaches and in Certification/Regulatory issues surrounding aero engine repair. Progress in Technology Repair technologies have also been the embryo from which new and revolutionary manufacturing technologies have evolved as well. Electron Beam Free Forming and LENS are examples of how a completely new manufacturing concept can evolve what was originally only a process to join metals. The current and future potential of these spin offs is discussed providing examples of application. While several problems have been solved over time with the implementation of advanced repair technologies, the demands of the industry have created new challenges. The paper describes these issues, outlines potential solutions and discusses the future of repair technologies in terms of the far reaching influence it is sure to have in design, manufacturing, maintenance management and life extension. Progress in Business Trends.Business approaches to repair and maintenance have also gone through considerable change with the introduction of ""Power by the Hour"" and other similar arrangements between the companies responsible for engine overhaul and the end-users. Program Based Logistics (PBL) is yet another innovation to provide a win-win situation for the repair service provider and the end user. This paper traces the development of these business initiatives and highlights successful applications. Progress in Repair Certification, Regulatory Issues.Understanding of the issues surrounding certification of repairs has also evolved with time and regulatory issues have been clarified considerably. Procedures for analysis and testing are much clearer and ""Check Lists"" are being drafted for certifying repairs on various engine components. The PMA phenomenon has added yet another dimension to the issues regarding certification and these are discussed as well."

Jan 1, 2010

By Fred E. Gray

The mill of Bralorne Mines, Limited, is located on the government highway in the Bridge River mining district of British Columbia, approximately fifty miles northeast of Shalalth, the shipping point on the P.G.E. railway. Prior to 1931, the property now owned by Bralorne Mines, Limited, was operated by Lorne Gold Mines, Limited. During the early operation of the mine, the ore had been treated at various times in one of three small amalgamation mills on the property. With the succession to ownership by the Bralorne Mines, Limited, work was started on construction of a new mill of approximately 100 tons capacity per day. The new mill was put into operation in the month of February, 1932, and since that date has been in continuous operation, milling an average of slightly over 3,000 tons of ore a month. The ore treated in the Bralorne mill is a gold-bearing quartz containing a very small amount of silver. About 75 to 80 per cent of the gold is in the form of free gold, the principal remaining portion being intimately associated with pyrite and arsenopyrite. The gangue rock is quartz, together with varying but relatively small amounts of altered diorite or albitite. In some of the ore, usually the higher grade portions, there is also considerable talc, which forms much slime in grinding. The mill is situated near the portal of the main haulage tunnel and the ore is received directly from the mine ore-trains, which dump on to the grizzly over the coarse-ore bin of the crushing plant. Figure 1 shows the flow-sheet of the mill as it is now being operated. Various changes have been made in the flow-sheet and in the reagents since the commencement of operations, and doubtless minor changes will continue to be made in order to increase the efficiency of the mill. Among the more important changes were those from two-stage to single-stage grinding, and from amalgamation plates to blankets. The change in the crushing was made because too much crushing was done when both primary and secondary mills were employed.

Jan 1, 1933

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By Richard Howie

Avian Diversity ?? Pre-mining ?? 110 - 125 species would have occurred ?? Dominated by forest species ?? Wetland productivity unknown ?? Post mining ?? 192 documented ?? Forested species in reduced numbers ?? Increase in wetland species ?? Increase in open country/grassland species

May 1, 2008

By Mark Liskowich

When is it the proper time to initiate engagement with various stakeholders, including Indigenous communities? This paper will demonstrate what stage of a project’s evolution is the appropriate time to initiate a stakeholder engagement plan. It will look at aspects to consider when identifying the communities to involve. It will describe the contents of a Stakeholder Engagement Management Plan as well and touch on how tried and true options analyses, such as a Multiple Accounts Analysis can be used to inform the results of the engagement, guide the development of your project and clearly document the engagement process. It will illustrate the benefits of initiating engagement at the appropriate point in your project’s schedule, and the limitations of doing so too early and at later stages of the project engineering. The benefits of this approach can be realized within any legislative Jurisdiction including the Canadian Environmental Assessment Act 2012 and Canada’s new Impact Assessment Act.

Jan 1, 2020

By G. Guzman

In the framework of the optimization of Teniente Converter operation the new system of automatic flux feeding through gar-gun was implemented in the Potrerillos Smelter, Codelco Chile, Salvador Division. The control algoritm based on simple iron and silica balance adjusted by empirical coefficients was incorporated in the logical programmer. The programmer works in real time gathering information from the plant instrumentation events and introduced chemical assays of concentrate, slag and flux. Through the auto-tuning of the automatic operation the criterions of optimal flux dosage were determined. Four month of operation of the automatic flux feeding system demonstrated the stabilization of magnetite content in the slag in the narrow range from 18 to 20% and the decrease of flux consumption, corresponding to annual savings US$ 340,000. Additionally, the automatic system helps operators in the control room in fast determination of optimal fluxing and avoid the errors in flux dosage affecting the slag quality and its impact on refractory wear.

Jan 1, 2007

By Christopher McElman

Real-time mine management solutions have evolved over time from closed, proprietary solutions, to a "system of systems" that may include a wide variety of off-the-shelf components and technologies. Modular Mining Systems has embraced open standards for their NextGen products to bridge the technology gaps between these systems. However, the remaining logical gaps must be overcome, in order to achieve truly seamless integration between discrete systems. When dealing with volatile real-time management problems, the effectiveness of business process modeling and middle-ware can break down. Scientific principles of military command and control applied to mining domain help to achieve better alignment and reach the highest level of integration. The combination of open standards and off-the-shelf hardware and software with a deliberately structured command-and-control approach provides a clear evolutionary path from ad-hoc connected systems towards real-time management of a seamlessly integrated digital mine.

Oct 1, 2009

By P. A. Crane, N. Shirley, Aung Moe, H. M. Nicholson, D. Kan

Kazakhstan’s first commercial copper-leach solvent extraction-electrowinning plant, Central Asia Metals’ Kounrad project, was commissioned in April 2012. Exploiting low grade waste stockpiles produced during Soviet era open pit mining, a 10,000 tpa copper cathode plant was designed, constructed and commissioned within 18 months. Overcoming initial challenges with a workforce unfamiliar with the technology and with extensive periods of sub-zero conditions during winter the project has consistently met targets and produced high quality copper cathodes at cash costs of less than US$1/lb. Challenges encountered during the first two years of operation are described and future plans briefly discussed.

Jan 1, 2014

By James R. Hein

Manganese nodules form at the sediment surface of abyssal plains throughout the global ocean at water depths of about 4000-6500 m. The nodules form a continuum from purely hydrogenetic (all metals from seawater) to purely diagenetic (all metals from sediment pore waters), which will determine which metals of potential economic interest are enriched in the nodules. Another important factor in metal enrichment is whether diagenesis in the bottom sediment is oxic or suboxic. There are several nodule fields in the deep ocean that have received much attention with regards to economic potential, the most important being the Clarion-Clipperton zone (CCZ) in the NE Pacific, where the International Seabed Authority (ISA) has signed 12 contracts for exploration areas, each spanning 75,000 square kilometers. Those nodules are rich in nickel (mean 1.3 wt. %), copper (mean 1.1 %), and manganese (28%), with moderate amounts of cobalt (mean 0.2%), molybdenum (587 g/t), and lithium (129 g/t). A conservative estimate is that there exists 21,100 million dry tonnes of nodules in the CCZ, yielding more manganese, twice the nickel, three times the cobalt, and four times the yttrium than the entire land-based reserve base (economic plus marginally economic plus subeconomic reserves) for each metal. Total rare-earth elements (REEs) as oxides average 0.09% in CCZ nodules, a potential byproduct even at that grade because the heavy REE complement averages 26%, compared to less than 1% for the large land-based carbonatite REE deposits. The price for HREEs is much greater than for the light REEs. For comparison, the REEs in deep-ocean ferromanganese crusts are 3 to 5 times greater than nodules and the HREE complement averages 18%. Of the 12 CCZ contracts, 7 are with States (China, France, Germany, Japan, Korea, Russia, and a group of States (IOM); and 5 are with companies: G-Tec Sea Mineral Resources NV, Nauru Ocean Resources Inc. (NORI); Tonga Offshore Mining Ltd (TOML), UK Seabed Resources Ltd (Lockheed UK), and Marawa Research and Exploration Ltd. Three other nodule fields that have received attention are in the Peru Basin, which has nodules very rich in manganese (34%) and lithium (mean 311 g/t), the Penrhyn Basin (Cook Islands Exclusive Economic Zone), with nodules very rich in cobalt (mean 0.4%); and the Central Indian Ocean Basin (CIOB), where India has an exploration contract with the ISA. CIPB nodules have mean nickel, copper, and manganese contents of 1.1%, 1.0%, and 24% respectively.

May 1, 2013

By Robin Phinney

Certain statements in this presentation may constitute "forward-looking" statements which involve known and unknown risks, uncertainties and other factors which may cause the actual results, pe1formance or achievements of the Corporation, or industry results, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. When used in this presentation, such statements use such words as "may", "would", "could", "will", "intend", "expect", "believe", "plan", "anticipate", "estimate" and other similar terminology. These statements reflect the Corporation's current expectations regarding future events and operating performance and speak only as of the date of this presentation. Forward-looking statements involve significant risks and uncertainties, should not be read as guarantees of future performance or results, and will not necessa1ily be accurate indications of whether or not such results will be achieved. A number of factors could cause actual results to differ materially from the results discussed in the forward looking statements including, but not limited to, the factors discussed in the Corporation's annual information form filed on March 9, 2011. Actual results could differ materially from those currently anticipated due to a number of factors and risks. These include, but are not limited to, the failure to obtain necessary regulatory approvals, including environmental approval, the failure to secure full project financing, the failure to implement the recommendations set out in the Technical Report, the failure to raise financing to implement the recommendations in the Technical Report, risks associated with the mining industry in general (e.g., operational risks in development, exploration and production; delays or changes in plans with respect to exploration or development projects or capital expenditures; the uncertainty of estimates and projections relating to production, reserves and resources, costs and expenses; and health, safety and environmental risks), decrease in potash prices and exchange rate fluctuations. Although the forward-looking statements contained in this presentation are based upon what management of the Corporation believes are reasonable assumptions, the Corporation cannot assure shareholders that actual results will be consistent with these fonvard-looking statements. These fon\?ard-looking statements are made as of the date of this presentation and are expressly qualified in their entirety by this cautionary statement. Subject to applicable securities laws, the Corporation assumes no obligation to update or revise them to reflect new events or circumstances. This presentation is a market update based on the Corporation's public disclosure and does not form a part of any offer of securities, or constitute a solicitation of any offer to purchase or subscribe for securities. Any purchase of securities in the company should be made solely on the basis of information contained in the Corporation's public record which is available on www.sedar.com .

May 1, 2013

By Maureen A. McGuinness

Kidd Mine, an Xstrata Copper operation in Timmins, Ontario, operates a 400 t/h pastefill plant that provides paste backfill to stopes at the depth of 9000 ft. This paper will cover the operating practices of the pastefill plant both on surface and underground, highlighting tailings excavation, paste mix design and the pipe maintenance program. Kidd Mine, une opération d'Xstrata Copper à Timmins, Ontario, opère une usine de remblai d'une capacité de 400 t/h. Le réseau de distribution permet d'acheminer le remblai en pâte juste qu'à une profondeur de 9000 pi. Cet article couvrira le mode opératoire de l'usine de remblai tant à la surface que sous-terre en mettant l'emphase sur l'extraction des rejets miniers, la recette du remblai en pâte ainsi que le programme d'entretient du réseau de distribution.

Feb 1, 2008

By E P. Graham

Orebodies occur in an infinite variety of grades, shapes and sizes, and take many millions of years to grow. When extraction starts there is only one possible end -the mine sooner or later will run out of ore and shut down. If the mineral industry is to supply the ever increasing demands of modern civilizations, more and more metals must be found and mined. This will require a never-ending search for ore, and the development of every economic body, large or small. To justify the mining of a small orebody, it first of all must pay its way. If the size of the burden imposed by the capital cost estimates is not carefully worked out, an otherwise promising situation could be killed. The very nature of mining, as a transient industry, re-leases a steady stream of good used equipment, and the trained personnel to install and operate it. All manner of plans and layouts, which can be utilized at a new property, are available. Working these and other economies into the estimates will sometimes make enough difference to give a prospect the green light.

Jan 1, 1964

By A. W. Davis

"The Red Rose mine is in the Rocher Deboule mountains about 8 miles east of Skeena Crossing and a like distance south of the town of Hazelton; the most northerly settlement on the Prince Rupert line of the Canadian National railway and 177 miles northeast by rail from Prince Rupert. The mine workings are on the north side of Balsam or Red Rose creek; a tributary of Juniper creek that drains via Kitseguecla river into the Skeena near Skeena Crossing. A truck road 11 miles long extends from Skeen a Crossing (elevation 650 feet) to the Red Rose mill (elevation 4; 100 feet). The mine workings lie between 5; 600 and 6; 300 feet above sea-level. Mine and mill are connected by a 1-mile aerial tramway and a tractor trail.The Red Rose claims were staked about 1910 by prospectors attracted to the district by the construction and near completion of the railway between Prince Rupert and Jasper. For a number of years interest centred in prospecting a sheared zone exposed in a ravine between elevations of 5,425 and 5,825 feet. Several adits were driven and some high gold assays were obtained in vein quartz in the sheared zone, but this work did not develop sufficient ore and the property finally closed down. In the early twenties of this century tungsten minerals were discovered in the northern extension of the vein, but nothing was done to test this deposit. Finally, in 1940, spurred by the wartime demand for tungsten, the Consolidated Mining and Smelting Company of Canada drilled the tungsten-bearing vein, and although results were none too encouraging, underground work was begun in June 1941. The latter work disclosed substantial amounts of ore. A small mill, subsequently enlarged, began operation early in January 1942 and by the autumn of 1943 some 1,194,000 pounds of tungsten concentrate had been recovered. Mining ceased in November 1943 because of orders from the Metals Controller that no more shipments would be permitted."

Jan 1, 1954

By Himmelman. Nicholas P.

In this paper, the hardware foundations and data collection methods of a real time collision avoidance system for electric surface mining rope shovels are described. The primary goal of the system is to help a shovel operator avoid accidentally colliding the shovel?s dipper with either a nearby haul truck or the shovel?s tracks. To achieve this goal, the system requires complete and precise knowledge of the shovel?s geometry and movement, as well as the location of any nearby haul trucks. This paper describes the subsystems created to acquire this necessary information. This system is unique in that all of its components are mounted solely on the shovel and that it is designed to be easily retrofitted to a shovel without significant modifications.

Oct 1, 2009

By R. O. Loutfy, J. C. Withers

"Titanium powder is produced from a small fraction of sieved sponge, HDH of sponge or gas blown from a melt produced billet. Ore from foreign sources is chlorinated in a very high temperature fluid bed to make TiCl4, then vacuum distilled purified and then reduced to sponge by Kroll processing. Domestic ores of ilmenite or perovskite can be carbothermically reduced to Ti2OC which can be chlorinated at low temperatures of 250–400°C to produce TiCl4 which can be electrolyzed in a fused salt to Ti powder, or the Ti2OC used as an anode in electrolysis to produce Ti powder. The electrolysis process can be operated continuously to produce Ti powder at a lower cost than Kroll processed sponge including produce control size powder. Electrolysis processing was scaled up and operated at the commercial demonstration stage on a continued basis that verifies the potential of a low cost process to produce Ti powder.INTRODUCTIONTitanium and alloys of titanium powder have been elevated to strategic status resulting from a focus of producing meltless titanium components as well as a feed for additive manufacturing processing. However, the high cost of titanium powder has limited wide scale implementation of using titanium powder as a feed to any process to produce titanium components. Titanium powder free of alloying is available as sponge fines from the Kroll process as illustrated in Figure 1. Titanium alloy powder is much more expensive, also illustrated in Figure 1 produced from an alloy ingot or mil product as the feed and then transformed into powder by one of several melt form processes which accounts for the high cost of titanium alloy powder at approximately $60–150/lb. Ton lots of titanium alloy powder (i.e. Ti-6Al-4V) from one source is quoted at $120/lb. in the U.S. It appears that alloy powder production cost by current processing is not sensitive to volume."

Jan 1, 2016

By G. Vibert Douglas

It has long been recognized that there are considerable difficulties connected with the physical and chemical explanation of shoots of ore. The literature of Mining Geology has frequent references to this subject; but the reasons given for the actual location of primary ore-shoots have been very tentative. In practice, the geologist or miner depends to a great extent on sampling and assaying to determine the boundaries of profitable ore within the mineralized zone. An ore-shoot is a portion of a mineralized zone which has a sufficient concentration of valuable minerals to make it ore. Ore deposits have been classified according to many schemes. There are classifications based on morphology and on genesis. However, it is also possible to classify hypo-gene hydrothermal ore-bodies in terms of ore-shoots or vice versa. A.-Ore-deposits in which the whole of the mineralized zone is ore, which is the same as saying that the ore-shoot extends throughout the mineralized zone. An example of this type of deposit would be the pyritic mineralization of Rio Tinto. B.-The second type would comprise those deposits in which the ore-shoots bear some relation to the geological structure of the area: all deposits in which 'bonanzas' occur in folds in the zone, at the intersection of veins along certain fault (or joint) features and other such controls. There are a great many examples of this type: (a) The Rhodesian copper lodes, where Bancroft and Gray have pointed out the association of the shoots of ore with drag folds. (b) A similar association has been pointed out by Faribault for some of the gold veins of Nova Scotia, e.g., Mount Uniacke. (c) The great bonanza of the Comstock lode in Nevada. C.-Deposits in which the localization of ore has been effected by the chemical character of the wall-rock. Examples of this type are the Fahlbands of Scandinavia, and the 'indicator' deposits of Ballarat, Australia. D.-Lastly, deposits in which there is apparently no structural and no chemical control.

Jan 1, 1934