Search Documents

By J. Dubinski

This paper describes the key circumstances of the underground coal gasification (UCG) process, which is planned to be carried out in the Polish hard coal mine ?Wieczorek?. The construction and field tests of a UCG pilot plant have key issues that need to be addressed to realize the research project goal: the elaboration of a highly effective technology of fuel and electricity production. The project will conduct several monthly tests of gasification in the pilot geo-reactor, which will be constructed based on the results of laboratory tests. The realization of the process requires numerous appropriately prepared actions adjusted to natural conditions in the hard coal deposit. Based on scientific principles, it is necessary to elaborate the procedures related to the location of the UCG installation (including its legal and safety aspects), and to perform a technical risk analysis. In addition, it is necessary to determine the required mining, geological, technical, economic and organizational circumstances, while at the same time considering the real but constantly changing process conditions.

Aug 1, 2013

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By K. Purazrang, P. Musavi Garavi, P. Sh. Naseri, P. Abachi

The fracture behavior of high strength Al7050 alloy was investigated at room and elevated temperatures using small size, V-notched tear (called Kahn specimen) and compact tension, CT, specimens, respectively.To study the elastic-plastic behavior of the alloy, the tensile test was also performed on the sub-sized cylindrical tension test specimen. The microstructure of the alloy was examined using optical- and scanning electron- microscopy. The rupture mechanisms and crack path were also studied by examination of specimens' fracture surfaces using SEM. The microstructure examination revealed equiaxed grains and some elongated grains in rolling direction, with the areas of partial re-crystallized grains where coarse intermetallic particles are mostly found.In general, fracture surfaces were indicative of dimpled ductile type. Considering the fractographs of tensile specimens, the void growth mechanism is also dominant in fracture of these specimens. Nevertheless, in some regions, smooth areas can be observed due to the friction during rupture process. The results of mechanical tests at RT made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. According to elevated temperature, 150°C, test results and plots of log da/dt vs. log KI , the crack propagation behavior over discrete ranges of crack growth rates could be assumed linear and then be obeyed as a power law equation in the form of da/dt = A (KI)n .

Jan 1, 2015

By H. B. Merlin

"The past demands for energy and the contributions by the major sources are shown for the world and regions, and for Canada. Three forecasts of future demand are presented. By the year 2000, the world will be consuming energy at a rate of 670-700 x 1015 Btu/year. Canada's rate is estimated at 20 x 1015 Btu/year. Electricity will increase its portion of energy from 7.5 per cent to 15 per cent, and more than 40 per cent of the primary energy w1ll. be required to generate 1t. World, regional and Canad1an forecasts are g1ven for total electricity generated and for electricity generated in nuclear stations. The integral world requirement for energy by the year 2000 will be over 12 x 10 18 Btu. Current recoverable fossil and hydro reserves are about 18 x 1018 Btu. The total reserves are estimated to be seven times greater.World production of electricity in nuclear stations by the year 2000 will be almost three times the electricity produced in the world today. The amount of fuel consumed in generating this electricity will depend upon the types and mix of reactors installed. The heavy water reactors, alone or in conjunction with fast breeders and liquid fuel reactors, are the most efficient users of uranium and thorium resources. The heavy water reactors are also the most efficient producers of plutonium which will be required as fuel for fast breeders."

Jan 1, 1969

By T. Hofbauer, M. J. Dry, G. B. Harris, C. W. White

"Urban Mining is a term that is increasingly being used, and represents an appreciable source of secondary materials for the metals extraction industry, a source that does not incur mining costs, but does, at present, incur considerable disposal costs. Electric Arc Furnace Dust (EAFD) is probably the most common of these materials, with an estimated global production of 8 million tonnes annually, of which 1 million tonnes is generated in North America. The contained annual metal value in EAFD at current prices is of the order of $6 billion, yet, apart from the zinc, virtually none of this is recovered.Despite many attempts over the years, with pyrometallurgical, hydrometallurgical or hybrid processes, currently the only commercially viable method of treating these materials is smelting in a Waelz Kiln (or a Rotary Hearth Furnace), which essentially recovers only the zinc, in an impure oxide form, and generates a secondary slag waste, which is still toxic and requires disposal. This paper describes the development of a chloride-based treatment process to recover all components of the EAFD in a marketable form, which centres around the novel hydrochloric acid recovery and recycle operation. Laboratory, miniplant and pilot plant data are presented, leading to the definition of a viable process flowsheet enabling the recovery of pure iron and zinc products (the principal components of EAFD), together with secondary products such as copper, silver, lead, cadmium, magnesium and manganese. A rigorous mass-energy balance is used to examine the preliminary economics involved."

Jan 1, 2014

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011

By R. M. Berry

A brief outline of refining methods used to (1) upgrade yellowcake to nuclear purity and (2) convert the uranium to the chemical and physical forms required by the fuel fabricators is presented. The uranium hexafluoride (UF6) production facility now under construction at Eldorado, Port Hope, is discussed. Technological improvements in uranium refining are considered.

Jan 1, 1969

By The Staff

"THE Wabana iron ore mines, owned and operated by the Dominion Steel and Coal Corporation, Limited, .are on Bell Island in Conception bay, on the east coast of Newfoundland. Mining began on surface in 1895 and, although open-pit work is still done on a small scale, the entire output may be considered to•be derived from extensive submarine workings. In 1958 the average daily production of hematite ore was close to 12,000 tons, almost all of which was concentrated in a heavy-media plant. SUMMARYThe character, occurrence, and extent of the submarine bedded deposits enabled early operators to meet prevailing market demands with the minimum attention paid to exploration. Mechanization of the mine and the pressure for sustained high tonnages since 1955 have emphasized the importance of an expanded exploration and development programme.A serious handicap has been the impossibility of utilizing normal diamond drilling methods to explore ore conditions in advance of mining faces. Drilling between tl1e bedded zones has been done but the major difficulty has been to delineate ore reserves in the lower bed, which has the greatest ore potential of the three mineable seams."

Jan 1, 1960

Iron deposits of every major type except laterite occur in Quebec, and form one of the major iron ore resources of the world. The five principal types of ore described are: (1) hematite-goethite masses derived from iron formation through the oxidation and enrichment of iron by natural processes; (2) taconites consisting of fine-grained iron formation; (3) metataconites composed of coarse-grained iron formation; (4) iron and titanium oxide minerals in massive or disseminateed deposits within gabbro and anorthositic rocks; and (5) replacement or contact? metasomatic magnetite deposits associated with complex silicate and skarn mineral assemblages. Most of the ore, although relatively low grade, is easy to concentrate. The physical properties of the ores that affect the choice and efficiency of beneficiation methods are described. The extent to which iron ore from this area can be utilized in the future will depend on the continued use and improvement of highly efficient methods of beneficiation.

Jan 1, 1964

By E. Henderson, L. K. Daneshmend

Drawpoint control is critical in determining the cutoff point for load-haul-dump mucking operations to minimize dilution. It is also necessary to ensure even mucking distribution and to prevent possible hang-up of material within a stope. A prototype production monitoring and reporting system has been developed for load-haul-dump operations in under-ground mines. The system generates accurate and timely information regarding mucked tonnages and drawpoint and ore/waste pass utilization. The monitoring system integrates a PLC-based load weighing system with a radio frequency identification (RFID) system for locating the vehicle. The system records the identification and time of entry and exit of each draw-point and ore/waste pass visited during a shift, as well as the weight of each bucket load. A trial of the system was conducted at the CAN-MET Experimental Mine near Val d’Or, Quebec. The monitoring and reporting system functioned as designed, with the exception that the maximum read range of the RFID tags under dynamic conditions was found to be a limitation. RFID systems with greater range capabilities have been identified for a second generation system. The system is the first of its type in North America to demonstrate that RFID tagscan be successfully applied to locate trackless underground equipment. Because of their ability to locate equipment and personnel within underground mines, RFID systems should be considered a key technology for future mine information and process control systems.

Jan 1, 1996

By Brian L. Beninger

This paper discusses the application of the computer to coal preparation process predictions. In broad terms, the computer is used to perform two main functions. Firstly, the given float-sink analysis is interpolated and extrapolated to cover the entire actual range of raw coal specific gravity. Assumptions based on historical data must be made at times. Secondly, the partition curve, which, from historical data, defines the efficiency of a specific coal washing process, is applied to the washability data in order to determine the expected clean coal yield and quality. The vast amount of numerical work which is required to make a prediction of this type exhibits the need for computer methods in this area.

Jan 1, 1979

By Juan Asalgado

The JORC and NI43-101 codes impose that mineralized material has a reasonable prospect of economical extraction to be classified as Mineral Resource. For deposits close to surface and amenable to open pit mining, it is easy to show reasonable prospect of economic extraction running a Lerch-Grossman optimization. The Lerch-Grossman pit provides a transparent and repeatable way of separating the Mineral Resource (within the pit) from the remainder of the mineral inventory (outside the pit). Deposits amenable to underground mining are more challenging because of the variety of the underground methods. AMEC developed a stand-alone software package that outlines the material which has reasonable prospect of economic extraction for open stoping, block caving, sublevel caving and room and pillar. The software takes a block model file in ASCII and exports a 3D surface outlining the part of the mineralization that has a reasonable prospect of economic extraction, and which the Qualified Person can smooth out manually if required.

Oct 1, 2009

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013

By J. J. Denny

IN a preliminary paper (1) it was shown that the addition of small quantities of metallic aluminium powder almost completely inhibited the solubility of siliceous material in the beaker. Six rabbits exposed to quartz dust for six months all showed well developed silicosis. Seven rabbits exposed to quartz dust plus 1 per cent metallic aluminium powder for the same period did not develop silicosis. At that time, we were not in a position to state either the manner in which metallic aluminium reduced the solubility of siliceous material, or, from the animal experiments, whether the aluminium was acting locally or systemically, or for what period after the cessation of dusting it would continue to act. This paper reports the further progress of this investigation. CHEMICAL EXPERIMENTATION The technical details pertaining to the various substances used in the experiments are given in an appendix which is on deposit with the American Documentation Institute, Washington, D.C. For lack of space, it is not printed here. The term 'solubility' is used to indicate the concentration of silica in the solution under the conditions as noted, determined colorimetrically (2), and expressed as parts per million (p.p.m.). The term 'reduction in solubility' indicates the difference between the solubility of the .silica in the presence of the aluminium powder and its solubility in the absence of aluminium powder. It will be noted that the solubility figures for different samples of quartz with no added aluminium vary considerably. The figures do not refer to an equilibrium solubility of silica but to the actual amount of silica dissolved from a given sample in a given time at a given temperature. In view of the fact that quartz dissolves extremely slowly, it is evident that the actual figures in any case will depend upon the surface exposed, i.e., fineness of grinding of the different samples.

Jan 1, 1939

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By R. J. Rotzinger

The Gibraltar Mine and Mill facility were commissioned in 1972 by Gibraltar Mines Ltd utilizing a flowsheet consisting of two stages of crushing followed by a rod mill / ball mill grinding circuit. During operations a number of opportunities were evaluated to expand the mill capacity; however, the economics of the day did not allow any of these projects to proceed. The mine continued to operate until late 1998 when it was shutdown and put on care and maintenance due to low commodity prices. Taseko Mines acquired Gibraltar in 1999 and in 2004, with the improvement in the metal markets, made the decision to restart operations. During the restart planning a number of opportunities for mill improvements and upgrades were identified and, after operations were successfully restarted, the decision was made to once again review expansion opportunities for Gibraltar. Taseko evaluated various expansion alternatives eventually deciding to install a SAG Mill, convert the existing rod mills to ball mills and distribute the SAG discharge to the resultant six 6 parallel ball mills. This paper discusses the design, implementation and commissioning of the SAG mill grinding circuit.

Jan 1, 2012

By C. V. Deutsch, O. Babak, J. G. Manchuk

High levels of geological heterogeneity occurring over relatively short distances pose a challenge to the unconventional open-pit techniques used in oil sands mining. There is strong motivation to mine selectively and minimize dilution and loss; however, the large equipment and high mining rate used to meet production targets tend to reduce selectivity. A numerical model is developed to account for geological complexity, mining equipment, regulatory criteria, and other operational parameters. This framework is used for more accurate forecasts, optimization of equipment, and other operational decisions. An example demonstrates the approach in light of Alberta Energy Regulator criteria.

Jan 1, 2014

By R. Matusewicz

The key drivers for the copper smelting industry are a complex mix of economic and "human" factors which combine to drive technology in new directions and can provide a strong indication of future industry trends. Recent examples have been the drive to achieve increased scale of production and resultant cost efficiencies by using a single furnace high intensity smelting vessel, and the broad acceptance of Top Submerged Lancing (TSL) technology for this duty. The development and adoption of continuous converting processes to counter the increased pressures faced by the Peirce Smith converting process is another example of the need for innovation. This paper discusses the merits of the continuous converting process, describes how the Ausmelt TSL batch converting process has been adapted to the new Ausmelt Continuous Copper Converting (C3) process in response to these industry trends and examines the Ausmelt continuous converting flowsheet options available to the end user.

Jan 1, 2007

By E. Dernedde

Industrial plants located in the province of Quebec, Canada, are subjected to large variations of the ambient air temperature, Building ventilation systems of these plants must have some flexibility in order to meet industrial hygiene standards (TLV for chemical substances, heat stress and cold stress) at any time of the year, The building ventilation of a bath treatment plant of an aluminium smelter in Quebec was examined under summer and winter conditions, Part of the plant has periodic emissions of hydrogen fluoride gas and heat from hot anode butts, CFD modeling was used to optimise the building ventilation of the bath treatment plant, The present study proposes a modified building ventilation system, which improves the internal environment, complies with industrial hygiene standards and also reduces heating costs by 20 % during winter.

Jan 1, 2005

By Nordau R. Goodman

T-he Ojibway Salt Mine near Windsor, Ontario, produces almost two million tonnes of97% pure rock salt annually. The salt is mined from the middle F horizon of the Silurian Salina Formation. The salt beds have a gentle dip into the Michigan depositional basin. There is no evidence of deformation. The rock salt is buff coloured and has a number of thin carbonateanhydrire bands. Secondary salt crysrallization occurs throughout the mine.

Jan 1, 1984