Search Documents

By R. W. Guill

"The Apex Mine is currently scheduled to be brought back into production by Hecla in the first quarter of1990. Its projected productivity rate will be exceptionally high for a small underhand cut and fill mine.The ore mined at the Apex Mine occurs within a pipe-like structure as a series of iron oxides containing both gallium and germanium, plus significant amounts of silver, zinc, lead, and copper.Ground conditions in and around the ore zone have dictated that unique approaches be utilized. To date, these have included a prototype 0.5 cu. yd diesel LHD, and the use of fibrous shotcrete in 4ft by 7ft headings, and the first pneumatically-placed cemented backfill in North America. Above all else, it is the combination of new technologies with a small and dedicated workforce which has allowed for the successful development of this ore body.IntroductionThe Apex Mine is an example of the typical small underground project. It has high grade, but low tonnage and is deposited in poor ground. In such cases, conventional planning and thinking generally results in an uneconomical evaluation and negative production decision. Fortunately, some unconventional thinking was allowed to take place during the planning and evolution of the Apex Mine development. The result now serves as an example of how such unconventional thinking can lead to the type of innovations described below.The job necessitated the development and use of new equipment and materials to execute a highly flexible underhand cut and fill mine design/pneumatic backfill concept, that must be constantly modified as different than assumed conditions become evident in and around the ore zone."

Jan 1, 1990

By D. Mraz

"Under high pressure in a deep potash mine, the salt rock behaves in accordance with the concept of a generalized, perfectly plastic substance. The paper presents the evidence of this behaviour and engineering concepts f or room-and-pillar design. IntroductionThe mining and refining facilities at International Minerals &. Chemical Corporation (Canada) Limited are located near Esterhaz y at the southeastern edge of the Saskatchewan evaporites. Ore extraction began in 1962 and at the present time the annual mining capacity is in excess of eleven million tons of potash ore.A generalized geological section is shown in Figure I. The mining horizon is overlay in by 100 feet of rock salt followed by a thin bed of competent dry shale. The strata in the next 1,500 feet are generally competent and locally water bearing. The Blairmore formation contains strata of water-bearing unconsolidated sand. Below the mining horizon, rock salt is interbedded with anhydrite bands.The 8-foot mining bed is distinguished mainly by grade and clay content, as there is no definite bed boundary. The chief mineral s are halite, sylvite and, in some cases, carnallite, with up to 2 per cent disseminated clay. The ore is coarse grained, with crystals averaging one-half to three-quarters inch across.The major mining problem is related to the fact that the Dawson Bay formation, overlying the evaporites, contains areas and channels that are highly porous and permeable and are filled with unsaturated brine under high pressure. Consequently, all mining areas, with no exception, must be so designed that the overburden salt stratum remain s competently supported for the duration of the mine .This paper outlines a successful engineering method of determining the stability of the pillar s and designing a stable room -and-pillar mining system."

Jan 1, 1980

By Free. Michael L.

Crushing ore prior to heap leaching enhances mineral liberation and creates fine particles that may require agglomeration to avoid permeability problems during leaching. Conventional modeling is relatively successful in describing general fluid flow and extraction in heaps. However, most models do not adequately account for the effects of mineral liberation and exposure or the effects of agglomeration, curing, and loading on heap leach performance. This paper will discuss methods to account for mineral liberation and exposure as a function of comminution. It will also discuss methods for incorporating liberation, exposure, and mineral locking as well as curing and fluid flow in heap leach modeling. It will also provide information regarding agglomeration and the effect of loading in heap leach modeling.

Jan 1, 2014

By J. L. Rodrigues Bravo

The aim of this paper is to show the results of the study that relate the variations of the bismuth content in the Caraíba Metais' electrolytic copper with the main electrolysis' process variables as electrolyte flow rate and temperature, anode's impurities content, electrolyte composition, current density, etc and their combinations and factors like cathode washing, blend of materials entering rod plant's furnace, analytical methods, shot-circuit inspection, etc. Also, the methodology considered arsenic, bismuth and antimony mass balance in the electrolysis and their electrolyte's molar ratio relations as well as bibliographic references of refineries that operate in similar conditions. The results showed the circumstances with the major probability of causing bismuth content increasing in the electrolytic copper and the main operating conditions that have to be fixed for having less bismuth variation and lower content in the electrolytic copper.

Jan 1, 2007

By David J. Forrester

Light metals, most commonly aluminum, magnesium and titanium, and alloys containing them, are used in many industrial applications where lightness, hardness, ductility and resistance to corrosion are needed. However, these metals and their alloys can be potential ignition sources in underground coal mines. There have been documented cases in the past where coal mine explosions have been attributed to firedamp/coal dust ignitions involving light metals or their alloys. When light metals and their alloys are brought into contact with oxygen bearing material, such as iron oxide (rust) in the presence of heat, then a "thermite" reaction can occur. This source of heat can be generated from frictional contact or from merely a glancing blow. This paper outlines the hazards associated with light alloys, how to address the hazard and regulatory aspects.

May 1, 2001

By H. Attia, S. Engin

This paper presents a practical approach for determining the optimal spindle speed and the depth of cut in a milling operation within the ever-increasing economic and technical constrains. Analytical modeling and experimental work has been carried out to predict chatter in such operations. The stability lobes determined from this analysis were then used as a constraint in the optimization of the cutting process. The optimal cutting conditions are determined for two different objectives: maximum metal removal rate and minimum cost per unit. It is demonstrated that this approach can be generalized to impose multi-level constrains, e.g., surface integrity and machining accuracy. The approach presented in this work was examined and validated on three NC milling machines. The productivity improvement, cost reduction, while respecting part quality requirements, is demonstrated.

Jan 1, 2006

By G. B. Hobbs, S. Saimoto, L. Collins

"Plastic yielding and flow in metals is dependent on the microscopic process of simple shear along crystallographic planes and directions known as slip. Thus, by altering the crystallographic direction of the stress axis or placing constraints in the direction of plastic flow, anisotropy of yield strength for the same material is observed. This phenomenon is called texture strengthening. The application of this concept to highly anisotropic crystal structures such as the hexagonal group of titanium and zirconium alloys, the former in missile casing and the latter in nuclear reactor fuel tubing, seems obvious. The outstanding example in cubic structures is the case of deep-drawing steel. The R value, the width strain over the thickness strain during a tensile test, is taken as a measure of texture strengthening. In face-centred cubic structures, texture strengthening has been completely ignored on the basis that materials with R less than one are not amenable to this beneficiation. This study will review two aspects of texture which will lead to strengthening, first the thermal stability of the deformed microstructure, which is dependent on the stress axis, and second, the texture strengthening aspect of fcc metals.A review of recovery and recrystallization in textured aluminum wires, copper and cupro-nickel sheet will be presented with the view of extending these concepts to the manufacture of heat-exchanger tubing. The superior creep properties of specially processed commercial products such as TD-Ni, TD-NiCr and MAR-M200 will be shown to be a manifestation of the same physical phenomena."

Jan 1, 1981

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By E. Landry, W. Naudts

"The amenability theory was developed by Alex Naudts and considers grouting operations as continuous permeability tests where Newtonian test fluid water, is replaced by a cementitious or solution grout. It utilizes hydraulic conductivity and grouting data to establish the amenability coefficient of a particular grout zone. The amenability coefficient reflects the quantity of apertures or voids accessible to the selected grout, divided by the number of apertures accessible to water, in the zone intersected by the grout hole. By calculating, in real time, the effectiveness of a particular grout at the start of a grouting operation, the most appropriate grout to match design criteria can be targeted. By incorporating the amenability theory in every grouting operation, schedule savings and an increase in productivity are typically achieved. Three short case studies illustrate different enhancements in productivity: At an underground mine during the construction of declines, a cement based suspension grouting program was highly ineffective and did not appear to affect the inflow into the mine workings. The amenability theory was utilized to evaluate the grouting program and based on this evaluation, changes to the grouting program were made which allowed the grouting to meet the project’s objectives. On another project, a pre-excavation grouting program implemented during shaft sinking operations utilized the amenability theory to select the most suitable grout for the program. Schedule constraints also influenced the selection of the grout. In the third case history presented, the amenability theory was used to select the grouting sequence of every individual grout hole for a grouting project in a highly heterogeneous soil formation. INTRODUCTION The amenability of a given soil, civil structure or rock formation for a particular grout formulation is a measure of the ability of that grout to permeate the pores, fissures and apertures water will flow through. The amenability coefficient of a particular grout for a specific zone equals the percentage of apertures, pores and fissures accessible by water that are also accessible by grout. Grouting should be viewed as a continuous permeability test, where the apparent in-situ hydraulic conductivity value for a particular grout zone is continuously evaluated, using grout instead of water as test fluid."

Jan 1, 2019

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By R. T. Erskine

"IntroductionIn this paper it will not be possible to cover all details of the reagent systems at Brunswick Mining and Smelting but it is hoped that a description of the evolution of these systems will be of some benefit. The concentrator of Brunswick Mining and Smelting located near Bathurst, New Brunswick was originally designed as a 3,000 ton per day operation but before construction commenced was uprated, with 4,500 tons per day being treated by the summer of 1964. Development of the open pit at another ore body five miles away was initiated in 1965 and additional concentrator and crusher facilities went into operation in September, 1966. Present total daily throughput is over 8,000 tons per day. The ore at Brunswick is very high grade but mineralization is very fine grained and requires grinds generally over 75% minus 400 mesh for liberation. The amount of surface exposed using grinds of this order understandably requires great quantities of reagents, Reagent mixing systems for the original concentrator allowed only for batch mixing and were very expensive in labour cost especially.During the first three years of operation total number of men employed in reagent handling reached a peak of four men per shift and six men on dayshift unloading cars for a total of 22 men. At present only one man is employed on shift, and four men on dayshift take care of unloading and mixing reagents, a total of 8 men. The man on shift is almost entirely occupied with checking feeder operation, flow rates, and head tank levels. Most commonly used reagents are tabulated in Fig. 1 showing average monthly and daily requirements in the Brunswick operation as well as pounds per ton of mill feed as found in 1969. It is very obvious that with over seventeen tons each of lime and soda ash and six tons of copper sulphate used each day, opening of bags and mixing batches of solution is an inefficient undertaking."

Jan 1, 1970

By R. L. Veenstra

This paper explores the connection between the stresses observed and the failure mechanisms present in the modelled cemented paste backfill. In order to look at this connection, the authors have used a previously developed model to conduct a sensitivity analysis of the model?s strength and permeability input parameters. The results from the sensitivity analysis were then compared to determine what causes modelled stresses and failure mechanisms to vary. Increased insight into the behaviour of the modelled paste will help clarify how paste behaves in the field.

Aug 1, 2013

By Robert Macdonald, William Coombe, John F. Lewry

Gold occurrences have been known in the La Ronge Domain for many year . Mineable reserves have more recently been outlined and there is every prospect of a major gold camp being established in the domain within this decade. The La Ronge Domain lies in the Lower Proterozoic 'Trans-Hudson Orogen' and is part of a collage of Early Proterozoic crust comprising volcanoplutonic arcs, batholiths, associated volcaniclastics and volcanogenic sediments lying between the Superior Craton to the outheast and the reworked Archean basement/Aphebian cover terrain to the northwest. The domain has several lithostructural subdivisions, the most important of whjch , from a gold exploration point of view, is the Central Metavolcanic Belt. This belt is composed dominantly of a range of metavolcanic rocks and gabbroic to granitic intrusives, which geochemically resemble younger subduction-generated 'primitive' arcs developed on oceanic crust. U-Pb zircon geochronology indicates that the arc volcarusm and pre- to late-kjnematic plutonism occurred about 1890 Ma to 1850 Ma ago. The belt has an attained grade of upper greenschist to amphibolite facies and is relatively undeformed , though high strain zones occur locally. Most gold occurrences in the La Ronge Domain have been found in the Star-Waddy Lakes area of the Central Metavolcanic Belt, and in the Sulprude-MacKay Lakes area to the south which is interpreted as a tectonically dismembered part of the main belt. Both tratiformand vein-type gold occurrences are present in the domain; vein-type predominate and form nearly 90 per cent of the occurrences. The stratiform-type occurrences show a regional lithological a sociation with iron-rich sediments within proximal felsic volcanjc sequences. Some vein-type occurrences appear related to brittle fracturing associated with intrusive emplacement (the magmatic-hydrothermal "syn:' and "subvolcanic" veins) and faulting. However, most of the vein-type occurrences exhibit a spatial association with regionalscale ductile shear and other high strain zones, and were probably formed by metamorphichydrothermal processes.

Jan 1, 1986

By Carl Faessler

Abstract Some Canadian geologists believe chat, in the Grenville sub-province of Eastern Canada, there is no granitic intrusion older than the anorthosite. The writers are among those who hold the contrary view. They suggest a new means to distinguish between rocks belonging to intrusions respectively older (Laurentian) or younger (Pine Hill) than the anorthosite. This new method is based on microscopical observations which demonstrate that the Pine Hill intrusives contain a large amount of exsolution perthite, whereas the Laurentian intrusives are completely devoid of exsolution perthite. Where perthite is present in Laurentian rocks, it is the result of lacer hydrothermal replacement. Introduction The present paper is the result of a systematic study of some acidic intrusive rocks in the Grenville sub-province. These rocks underlie large areas of the Canadian shield in the Province of Quebec, mostly along the southern border of the shield.

Jan 1, 1946

By Avinash Kandalam, Markus Reuter, Jörg Kleeberg, Michael Stelter

The Top Submerged Lance (TSL) technology has obtained significant importance in the pyrometallurgy industry for nearly four decades. One of the advantages of TSL furnace is its high reaction rate, which is caused by splashing and turbulence of the melt. In contradiction, this phenomenon stands as a barrier for conducting experimental investigations to validate the simulation models. The highly turbulent and splashing environment in the TSL furnace is caused due to the immersion of the lance into the slag layer and thus the effect of the flame structure is directly related to the splashing, turbulence, reaction kinetics and life-span of the lance. Moreover, the material properties such as viscosity, density and the surface tension will also influence the flame structure. As a first step to understand the flame structure, attempts are made to generate a stable flame of the lance in an open environment. INTRODUCTION Top Submerged Lance (TSL) technology was invented during the 1970s at Commonwealth Scientific and Industrial Research Organisation (CSIRO), Australia by Floyd and Denholm. This technology was later commercialised and currently, there are about 100 TSL plants around the world commissioned by various licence holders such as AUSMELT (Outotec) and ISASMELT (Xstrata- Glencore Technology). Copper is the most produced non-ferrous metal followed by lead and zinc, see Hunt (2005). Today, a wide range of primary, secondary, and complex recycling materials are used as a feed material in the TSL, Alvear et al. (2010), Kaye et al. (2008). The working principle of TSL technology lies on inserting and submerging a lance from the top of a vertical cylindrical chamber into the slag layer. The lance is considered as the heart of the furnace, where the air and fuel are transported through two concentric tubes and are mixed in a combustion chamber, which is approximately 7 cm from the tip of the lance (considering the pilot-scale TSL furnace at the Institute for Nonferrous Metallurgy and Purest Materials - INEMET). The TSL furnace is very flexible with the type of fuel, feed material and the air input. The fuel can be natural gas/heating oil/fine coal particles and the air could be enriched with oxygen (Figure 1). The general mechanism of the TSL furnace lies on feeding the material from the top of the furnace and the material is pulled into the molten bath due to the high turbulent atmosphere, which results in high reaction rates. The thermocouples installed in the furnace (i.e. in the ceramic linings) allow the operator to know the temperature of the melt. For example, in the case of copper production the tapped material (i.e. matte/metal) can be transported to a settler for further processing or directly used.

Jan 1, 2019

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By A. Karzhau, B. Aldamzharov, Y. Tussupbekov

"This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of the mine 24 hours a day. The mine auxiliary ventilation has been designed with the maximum length of ducting systems with extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal. The mine needs additional investments for re-designing ventilation network and therefore needs to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation network optimisation processes at the operational metal mine in Kazakhstan. Mine ventilation surveys were undertaken for validation of the computerised ventilation model. The mine ventilation network modelling has been undertaken to be compliant with Kazakhstan mining regulations. Results of the mine ventilation optimisation processes were analysed in terms of financial risks for investments into reconstruction of the ventilation shafts, extension of the ventilation network, variable speed fans and automated regulators. Savings were resulted from improving ventilation system efficiency by reduce airflow in areas without mining activity and redistributing existing ventilation capacity. Based on savings derived from the optimised ventilation network an additional NPV has been received. Stochastic modelling use Monte Carlo simulation producing representation of possible outcomes for the additional NPV considering electricity pricing as a major variability. As result probability distribution for the optimised ventilation network demonstrates the additional NPV in a range of 1.6 - 2.2 million US$ in the corresponding defined value of 90%. Moreover, there is only 5% chance that the additional NPV to be less than 1.5 million US$. Conducted risk analysis for ventilation network optimisation processes gives considerations on volume of investments into the mine ventilation system.INTRODUCTIONCosts for mine ventilation are typically increasing when mines expand to deep levels. Some underground mines in Kazakhstan still use continuously operating fans at its maximum capacity. This is not helping to save energy and costs that are in many cases very significant. This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of a mine 24 hours a day. The mine auxiliary ventilation has been designed with maximum length of ducting systems and extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal from the mine workings (Sabanov, 2019). The mine needs additional investments for re-designing ventilation networks and therefore need to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation networks optimisation processes at the operational mine in Kazakhstan. Mine ventilation surveys for validation of the computerised ventilation model have been undertaken"

Jan 1, 2019

By M. G. Rylatt, G. M. Popplewell

"Production from Canada's first diamond mine is planned for the last quarter of 1998. The climatic conditions and the variation in kimberlite types to be treated have lead to the development of a compact and flexible processing plant.High kimberlite moisture contents and winter temperatures below -40°C have dictated a process flowsheet with limited in-circuit storage to reduce materials handling difficulties. The latest developments in High Pressure Grinding Roll technology will be used to liberate the valuable diamond, reduce diamond breakage, and increase fines production to reduce the amount of material for down stream processing in the Heavy Medium Separation section.A varying heavy mineral concentrate yield has lead to the development of a final Recovery section that will incorporate Attrition Milling and Wet High Intensity Magnetic Separation for concentrate reduction. The latest developments in diamond X-ray sorting will be used to produce a final diamond concentrate for mechanical sizing, weighing and packing.Fine tailings thickening will utilise Deep Bed Compression type thickeners. This relatively new technology can produce;i) high underflow densities at low flocculant dosage rates, andii) clear overflowswith a smaller thickening area than conventional high-rate thickeners."

Jan 1, 1998

By Olli Haavisto, Lauri Koresaar, Navid Khajehzadeh

In recent times sustainable minerals processing is an important topic in research. Sustainable mining is linked with efficient use of energy and human resource in all process stages including beneficiation of the ore. Controlling and optimizing the recovery while preserving the grade of the concentrate is extremely important in flotation plants. This development requires new technological solutions and has given rise to the multitude of application areas for lasers. X-ray Fluorescence (XRF) and Laser-Induced Breakdown Spectroscopy (LIBS) are currently two of the predominant non-contact and direct analysing methods in industry. LIBS and XRF measurement techniques both have high capabilities for measuring elements. LIBS has a very simple and easy-to-implement spectroscopic setup, wider range of elements can be detected with online LIBS and measuring light elements is simpler by LIBS compared with XRF. It is of great interest to extract mineralogical information from the elemental results with no modification on the measurement setup. In order to achieve this, more advanced interpretation of the elemental peaks of LIBS spectra is required. Therefore, the major focus of this research is about measuring mineral concentrations from the elemental lines of LIBS spectra using advanced statistical methods. This accomplishment provides knowledge about mineral concentrations from the real-time assay data of the slurry LIBS analyzer. Consequently, this paper first discusses an analytical method called partial least squares regression leading to rapid mineral identification from the elemental contents of the LIBS technique. Then the technique is employed to analyze the mineral contents quantitatively through the information acquired from an on-stream LIBS slurry analyser. This can lead to many benefits such as rapid control of concentrate quality, enhanced recovery, saving time, energy and manpower.

Jan 1, 2016