Search Documents

By T. Negeri, M. Boisclair

"A hybrid process consisting of flotation and magnetic separation has been developed to concentrate multi-phase rare earth minerals associated with a carbonatite ore that contains a significant amount of niobium. Fine grinding to a d80 of <65 microns was required to obtain acceptable separation of 92% of the contained total rare earth oxide (TREO) and niobium in half the feed mass. Whereas it was possible to obtain 85% of TREO in 28% of the feed mass through staged cleaning, it was demonstrated that at least 87% and 85% recoveries of TREO and Nb respectively could be achieved in 16% of the feed if the rougher-scavenger concentrates were calcined, quenched, reground to <25 µm and then magnetically upgraded. The paper discusses the overall concept of the flowsheet and the experimental strategies that led to this progress. INTRODUCTIONOut of the approximately 250 minerals known to contain rare earth elements (REEs), only about 60 of them contain REEs in significant amounts. Over 95% of the world’s rare earth oxides (REOs) are believed to occur in the form of three minerals (Pradip & Fuerstenau, 1991) namely bastnaesite (Ce,La,Y)CO3F, monazite (Ce,La,Nd,Th)PO4 and xenotime Y(PO)4. An estimated 51.4% of global REO resources are hosted by carbonatite deposits with the same three minerals as major constituents (Weng et. al., 2015). Any one of the REEs or commonly all of them can be found in these minerals (Ravnaas, 2010). As the demand for critical REEs increases due to the ever increasing applications in advanced technologies, many deposits containing other forms of REE minerals will have to be developed. REE minerals are extensively dispersed and intergrown with several oxides, silicates, carbonates, and phosphate minerals. Consequently it is possible to liberate them only at fine grinding and is thus difficult to separate and produce high grade rare earth mineral concentrates. Most of these minerals contain other important elements such as tantalum (Ta), niobium (Nb), uranium (U), and thorium (Th) in varied quantities. REE minerals in the same ore may exist as carbonates, fluorocarbonates, niobates, silicates, phosphates etc. in association with gangue minerals belonging to different mineralogical groups."

Jan 1, 2016

By Deng Yang-wu, Zhang Yan, Chen Chun-fei, Luo Xian-ping, Luo Cai-gui

This paper summarizes the ecological imbalance status of abandoned rare-earth element (REE) mines in southern China. These include large areas of vegetation damage, serious water and soil erosion, landslides, mudslides, heavy metal pollution, water pollution, soil contamination, and fluorine pollution. The causes which lead to the ecological imbalances at abandoned rare-earth mines are analyzed, such as: the inadequacies of using vat leaching, heap leaching, and in-situ leaching processes to extract REE resources; low mineral thickness and low grade of REE ore; and low utilization rates of the resource. Southern ionic REE resources are not fully integrated, with limited access and ineffective supervision of REE mining by relevant departments. The ecological recovery research for ionic-type REE mines is lagging behind, and there is no deployable ecological restoration method for REE wasteland. In the end, the following suggestions are made to improve the ecological imbalance status of rare-earth mine in southern China: develop new rare-earth extraction processes, accelerate the integration pace of REE resources, increase investment in ecological restoration research in rare-earth wasteland, and so on.

Jan 1, 2014

By M. Niinae, F. Nakahara, T. Kawamoto, T. Suzuki

"MgO was chosen as an As(V) immobilization agent and a series of immobilization experiments was performed to obtain insights into the behavior of As(V)and MgO during leaching tests. Our experimental and modeling results demonstrated that As(V) immobilization by MgO consists of the following steps: (i) an increase in soil pH, (ii) desorption of As(V) from the soil, and (iii) the re-immobilization of As(V) by MgO/Mg(OH)2particles. Regarding the behavior of MgO, the modeling results showed that when the MgO dosage was 25 mg MgO/4g-drysoilor less, the majority of MgO was used to increase pH, and less than 1% of MgO was used to sorb As(V), which was consistent with the result of leaching tests showing that a high level of As(V) was leached at the MgO dosages. On the other hand, when the MgO dosage was above 25 mg MgO/4g-drysoil, the percentage of MgO used for As(V) sorption increased up to 35%, and correspondingly, the As(V) leaching level decreased to below 0.01 mg/L As at an MgO dosage of 75 mg MgO/4g-drysoil.INTRODUCTIONOne of the major arsenictransport pathways causing groundwater contamination is the migration of arsenicfrom artificially or naturally contaminated surface soils. Therefore, in this study, the immobilization of arsenate (As(V)) in soils was investigated using commercial-grade magnesium oxide (MgO) as a potential cost-effective measurement to prevent the occurrence of groundwater contamination with As(V).With respect to the use of MgO for remediating As(V)-contaminated environmental media, MgO has been used in several studies to remove As(V)from water(Yu et al., 2011; Jia et al., 2013; Tresintsi et al., 2014). Although these studies demonstrated that MgO effectively removes As(V)from water in water-MgO systems, the behavior of As(V)in water-soil-MgO systems has not been evaluated in the literature, and several questions remain to be answered to comprehensively evaluate the use of MgO as an As(V)immobilization agent in soils. For instance, as is well-documented in the literature(Ford, 2002; Lenoble et al., 2002; Zeng et al., 2008), iron oxy-hydroxide (FeOOH) is one of the important adsorbents for As(V)in both natural and engineered systems. Therefore, it is anticipated that the presence of FeOOH in soils significantly influences the behavior of As(V)in water-soil-MgO systems and consequently, the immobilization performance by MgO. Another important question to be answered is the behavior of MgO during the immobilization treatment. In our previous studies (Suzuki et al., 2013a, 2013b), commercial-grade MgO was demonstrated to effectively immobilize lead and fluoride, and the immobilization effectiveness was indicated to last more than 100 years against the exposure to acid rain (pH 4.0). However, these studies focused on the behavior of contaminants. As a result, little is known about the behavior of MgO during the immobilization treatment. The lack of understanding of the behavior of MgO during immobilization treatment is one of the main concerns leading to relatively low public confidence in immobilization treatments."

Jan 1, 2016

By J. Manchisi

This study has investigated the use of blast furnace slag as functional adsorbent for metal ions in acid mine drainage treatment. This opportunity has not yet been developed into a practical process partly because of limited understanding of rates and mechanisms of adsorption process and inconsistency in interpretations of adsorption data. The overall objectives were to determine the efficiency and mechanisms of sorption process of metal ions in a multiadsorbate system. We employed standard materials characterisation techniques to analyse composition, structure and surface morphology of the slag. Batch adsorption experiments were then conducted to study the mechanisms, kinetics and efficiency of metal sorption as a function of pH, phase ratio, mixing time, mass and particle sizes of slag. Both XRF and adsorption data suggested the slag to possess acid neutralising capacity. This slag is non-crystalline based on XRD pattern, has adequate porosity and pore volume comparable to similar commercial adsorbents but it has inferior pore structure, pore size distribution and BET surface area to be effective under wide applications. Metal sorption increased with decrease in slag particle diameter, decrease in initial metal concentration and increase in the mass of slag. Although slags have demonstrated to efficiently treat low concentrations of single and multiadsorbate effluents using fine particle sizes, they have limited capacity to treat multiadsorbate systems for some metal ions. This is probably due to low affinity, competitive adsorption or limitation in material?s adsorptive properties. Sorption mechanisms probably involve precipitation and ion exchange on the basis of alkaline pH and exchangeable slag surface ions. Sorption preference is proposed as Fe2+>Cu2+>>Cd2+>Co2+>Mn2+. Despite these limitations, deeper understanding of sorption behaviour of metal ions by slags for application in dilute and large volumes of effluents is necessary where precipitation and other standard techniques are either inefficient or uneconomic. Thus, this study has established that sorption capacity of slag to remove metal ions from acidic effluents is selective, limited to certain metal ions and for other ions only at low concentrations. Further adsorption studies in multiple solutes under various experimental conditions or those that can propose an economic slag activation process are needed that improves or widens adsorption window.

Aug 1, 2013

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

Despite the claims of energy efficiency and the considerable development that has gone into dramatically extending rolls’ life and facilitating rolls’ change-out, in the six years since the last SAG conference, only a few HPGR operations have entered the realm of mineral processing. Risk barriers to the take-up of new equipment or processes are: a massive increase in materials handling issues as well as in the number of pieces of equipment required, low total circuit potential energy savings, and similar or higher capital costs. An alternative route is to make use of the complementary strengths of the HPGR and SAG in hybrid circuits. Minimising materials handling issues, providing an ideal balanced feed to the AG or SAG mill, and improving controllability through shifting grinding load as the RoM feed changes, are all potential major advantages to this approach. Conceptual circuit layouts, based on real measured ore and equipment data, are presented here to illustrate the potential production upside, the reduction in operating costs and the reduction in the physical and energy footprints.

Jan 1, 2012

By P. Tukkaraja, K. Katzenstein

"Block caving is one of the most economical and efficient underground mining methods and has gained popularity around the world especially for extracting low grade and massive ore bodies. However, during the extraction of ore from the draw bells, gases trapped inside the cave could emit into the working areas; hence, ventilation plays a key role in operating block cave mines successfully where gas emission is a concern. To design an effective ventilation system for a block caving mine, given the dynamic nature of the caving process, it is necessary to develop airflow characteristic curves (P-Q) for a given cave. This study uses a 1:100 scale physical model with an exhaust fan system, and a Computational Fluid Dynamics model of a block cave to investigate the airflow behavior through the cave filled with broken rock material. From this study, it was observed that the cave airflow resistance increases with the decrease in cave porosity and the particle size.INTRODUCTIONThe block cave mining method is gaining popularity owing to its low cost and high productivity. This study considered a case where this bulk mining method is used for the extraction of an orebody that contains uranium mineralization. During the extraction of broken ore from the draw bells, radioactive gases trapped in the cave zone could be released into the production drifts and could create unsafe working conditions in the mine. Mine ventilation systems play an important role in regulating the migration of radon in working areas. One of the strategies to control radon migration in a block cave mine is to exert negative pressure on the cave zone by using an exhaust fan above the cave zone. In order to select an appropriate exhaust fan system, it is necessary to study the airflow resistance of the cave zone (Loring & Nelson, 2006).Extraction of broken ore via drawpoints creates a void volume inside the cave called the air gap. Air gaps with larger heights can lead to air blasts in a block cave mine should the cave collapse. Besides that, the air gap can also lead to decrease in ventilation system efficiency due to recirculation of air flow and associated shock losses. Air gap height can also have a profound effect on the variation of cave airflow resistance (Erogul et al., 2015, 2017). The knowledge of cave airflow resistance is also important for predicting the intensity of an air blast. Cave airflow resistance is a function of cave properties such as broken rock size, air gap, and porosity inside the cave zone (Baysal et al., 2017). Initially, a scaled experimental model with a forcing system was developed to investigate the airflow behavior through the cave, however, this model couldn’t provide an observable change in the airflow resistance when the cave properties were changed (cave porosity, and airgap) This was attributed to the difficulties associated with forcing system in terms of achieving lower porosity values with the available material (lightweight shipping boxes) for simulating broken rock inside the cave zones, and controlling air leakage from the model (Ajitha et al., 2018)."

Jan 1, 2019

By S. Kelebek

Efficient separation of minerals is the essence of mineral processing. Separation of hexagonal pyrrhotite in processing of Ni-Cu sulphide ores was investigated together with particle size effects with respect to selective flotation recovery of pentlandite and nickel. The recovery by size response was compared for sodium metabisulphite (SMBS), triethylenetetramine (TETA) and their combinations with amyl xanthate as a collector. The pyrrhotite recovery for all sizes was lower than that of pentlandite for the blank case as well as individual cases with SMBS and TETA. For pyrrhotite, the recovery by size relations in the case of individual uses of reagents were mainly determined by recovery losses at coarser size range (>74 um), which occurs at a coarser size for pentlandite (>212 um). The combined use of SMBS and TETA, and the associated synergistic effect very significantly knocked down the pyrrhotite recovery to less than 7% that was a maximum for the –10 um (attributable to hydraulic entrainment). High recovery of pentlandite in a wide range of intermediate sizes and drastically low recovery of pyrrhotite resulted in a very efficient separation of pentlandite from pyrrhotite in all sizes. Separation of this mineral is discussed in relation to fundamental functionality of the reagents used.

Jan 1, 2017

By F. Romero

In the last four years, Compañia Minera Doña Ines de Collahuasi has been working in the application of advanced multivariate statistical techniques for the improvement of the metallurgical processes. In this paper the main conclusions for the application of multivariable analysis to the EW process are presented; including the identification of (target) process patterns according to throughput and quality criteria. Based on the process patterns, process variables hierarchies were identified by selecting the most influential ones, as well as to identify and isolate the root causes of pattern deviations and sub-standard operating conditions, cause-effect relationships were established, leading to the definition of process policies and controls to give early corrections to potential failures. The analysis was focused on cathode quality, specifically in its sulfur content, using an empirical model based on those variables that from a phenomenological and statistical stand point appeared to be the most influencing ones.

Jan 1, 2007

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

This paper presents the results of research aimed at proposing new solutions in the area of belt conveyor elements. Many factors, such as energy consumption costs, and operating costs of belt conveyor elements, including belts, idlers and drives have an impact on the operational costs of conveyors. The paper presents special tests of new materials for the bottom cover of an energy-saving belt conveyor, which decrease rolling resistance. It also presents large-scale in-situ tests of a high-output belt conveyor for the purpose of simultaneous measurements of various types of conveyor belts (standard vs several energysaving types) under typical operating conditions of a lignite surface mine. Improvements in materials used for the bottom belt covers, supported by specially developed comprehensive tests of the new types of belts have provided valuable results of various proposed solutions. Since the tests of belts were done at exactly the same time and in the same operating conditions, direct comparison of the results is valid and should lead to a substantial decrease in the conveyors? drives? energy consumption, which will improve the effectiveness of belt transport and minimize its negative influence on the environment.

Aug 1, 2013

By J. H. Pee, Y. J. Kim, H. U. Lee, G. H. Kim

The general recycling process of tungsten scrap to produce tungsten raw materials (tungstic acid, ammonium paratungstate (APT) and WO3) have been carried out by the oxidation, milling, sodium-fusion, dissolution, and extraction processes. Many studies on the high temperature oxidation of tungsten scrap have investigated various aspects such as swelling kinetics, fracture resistance, and the effect of alloying composition. However, the accelerating factors on the scrap oxidation rate during oxidation were not considered here. In general, oxidized products were fused with sodium carbonate or sodium hydroxide to produce Na2WO4. Later in the process, solid Na2WO4 was dissolved in water. This process required considerable reaction time and was a costly process. Therefore, the aim of this study was to increase the solubility of solid oxidized products to produce Na2WO4 solution by hydrothermal reflux method. Na2WO4 solution was used to produce CaWO4 and H2WO4 by general chemical reactions with calcium chloride and hydrochloric acid. Ammonia solution was also added to the tungstic acid to produce APT. In this study, the effect of ammonia addition on the APT precipitation process was investigated in detail.

Jan 1, 2015

By K. Soldenhoff

Mantra Resources Ltd is developing the Mkuju River project is southern Tanzania. The uranium deposit, hosted in ?Karoo? sandstone, is surface outcropping with the majority of uranium mineralisation occurring in the finer clay component of the ore. A flowsheet, consisting of ore beneficiation, acid leaching, RIP uranium recovery and direct precipitation of the uranium product, was developed and successfully demonstrated in continuous mini-plant operations at ANSTO. The selected flowsheet overcomes the difficult slurry rheology, arising from the clay component of the ore, by eliminating the need for a CCD plant. The RIP process was found to contribute to a high uranium extraction, by eliminating ?preg-robbing?, at a relatively low acid addition in leach, with the potential to eliminate ferric ion and oxidant additions.

Aug 1, 2010

In semi-enclosed coastal areas in Japan, phosphorus is often observed in the level of limiting phytoplankton growth, causing alteration of species composition from useful diatoms to nuisance dinoflagellates. On the other hand, the sediment quality is still degraded with organically rich reduced conditions. The latter is the major cause of oxygen-depleted bottom water formed in summer, and it makes benthic organisms difficult to live. Steel-making slag can be a source of phosphate and silicate that induce growth of diatoms, and further may remediate the reduced condition of the sediment through the formation of iron hydroxide that works as a kind of oxygen pool.

Jan 1, 2004

By J. Bensabat, B. Figueiredo, A. Niemi, J. Rutqvist, C. F. Tsang

"A hydro-mechanical model was developed to study the interaction between mechanical deformation and fluid flow in the fault zones during CO2 injection and storage at the Heletz site which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The potential reservoir for CO2 storage at the Heletz site consists of three sand layers separated by lowpermeability shale layers. The potential consequences caused by fault reactivation, focusing on the shortterm integrity of CO2 storage, are evaluated. The difference in the results obtained by considering the three-layer as an equivalent layer storage formation is analyzed.INTRODUCTIONLarge-scale storage of CO2 in deep underground reservoirs may cause considerable pore-pressure perturbation as well as flux migration and concern has been raised over whether shear slip displacements may be induced in nearby faults, as a consequence of their reactivation. A state-of-the-art review can be found in Rutqvist (2012), which describes the various possible effects resulting from CO2 injection into a deep sedimentary basin, including those involved in reservoir stress–strain changes, micro-seismicity, caprock sealing performance, and potential fault reactivation. Moreover, several studies have recently shown how CO2 injection may produce seismic events both on major faults (i.e., large faults with large initial shear offset) (Cappa & Rutqvist, 2011a, b, 2012), and on minor faults that might have gone undetected during the site characterization, e.g., faults less than 1 km long and without detected initial offset (Mazzoldi et al., 2012).The present paper is concerned with the Heletz formation which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The Heletz site located at the southern Mediterranean coastal plain of Israel and the structure is an anticline fold with a crest of about 4 km by 2 km. The structure is gently dipping to the east, truncated by a pinch-out line to the west and subdivided into a number of blocks by transversal normal faults with small displacements. The water table is located at 300 m below the land surface. An areal sketch of the site with the elevation of the caprock and the location of the borehole that has been chosen for the CO2 injection experiment is presented in Figure 1."

Jan 1, 2015

By P. A. Riveros

Antimony is commonly found in copper electrolytes and can contaminate the cathode deposit. Several methods, such as ion exchange, solvent extraction and precipitation, have been developed to remove antimony from copper electrolytes. However, past research has been carried out almost exclusively with Sb(III), whereas the presence and behavior of Sb(V) in the electrorefining circuit have been largely ignored. In this study, the behavior of Sb(V) species was monitored and compared to that of Sb(III) species, using specially developed analytical and SEM-EDS techniques. Significant differences in the behavior of the two species were noted. Although the solubility of Sb(III) increases with temperature in synthetic copper electrolytes, the solubility of Sb(V) appears to be constant over the range from 30 to 80°C. Whereas Sb(III) forms several crystalline oxy-sulphate compounds, Sb(V) appears to remain as an amorphous oxide. Both Sb(III) and Sb(V) are extracted by aminophosphonic resins, and Sb(III) is readily eluted by HC1 or complexing agents. By contrast, concentrated HC1 elutes Sb(V) inefficiently and complexing agents, such as EDTA and tartaric acid, do not elute Sb(V) to any significant extent. This observation implies that in industrial practice, unless special measures are taken, Sb(V) will accumulate on the resin, eventually impeding the ion exchange process.

Jan 1, 2007

By P. -A. Bosse, J. Robitaille, P. Blatter

The LaRonde ore is a Cu-Zn-Pb ore with gold (3-4 g/t) and silver (60-100 g/t). The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation. Subsequent to a recent mill expansion, excessive gold was reporting to zinc concentrate with a concurrent decrease in gold to copper concentrate. Owing to the higher return obtained from the metal, the mill endeavors to recover additional gold and silver to the copper concentrate and minimize the placement of precious metals to the zinc concentrate. A gold deportment study showed that the gold occurs mainly as küstelite, with a moderate amount of electrum and a minor amount of native gold. It also showed that various sulfur-based Au-and/or Ag-bearing coatings on liberated küstelite and electrum were the major mineralogical factors that caused gold and silver to report to zinc concentrate. By frequency, such coatings were observed on 70-80% of total liberated gold particles reporting to the zinc concentrate. Based on the gold deportment and the chemistry of the coatings, the collector chemistry was reviewed and a new collector was added into the circuit which resulted in a significant increase in gold and silver recovery to the copper concentrate. The information obtained from the mineralogy confirmed and guided other process optimization. In this paper, the authors will describe the process mineralogy of the LaRonde ores, and in particular, the mineralogical evidence diagnosing the problem. Reference will also be made to the rationale behind how the problem was solved, the results achieved, and future steps in optimization.

Jan 1, 2005

By Z. Zhao, B. Li

"Fractures are the key channels for fluid flow and mass transport in fractured rocks of low/negligible matrix permeability. In single rock fractures, surface roughness causes fluid flow in tortuous paths, and reduces the overall fracture conductance. A number of empirical models have been proposed to relate the reduced hydraulic aperture to the mechanical aperture due to surface roughness, which were revisited and compared. Using two of those relationships between hydraulic apertures and mechanical apertures, we studied the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks. The results show that fracture roughness can affect the flow rates and residence time to varying extent, mainly depending on the empirical models between hydraulic apertures and mechanical apertures. However, fracture roughness has negligible influences on the general patterns of fluid flow (channeling) and solute migration (e.g., travel paths and shape of breakthrough curves). This is because the connectivity of a fracture network is mainly determined by other geometrical parameters (fracture positions, orientations, and lengths), rather than roughness or apertures. INTRODUCTIONIn fractured crystalline rocks of low or negligible matrix permeability, fluid flow and contaminant migration mainly occur within the connected fractures. An understanding of fluid flow and contaminant migration in fractured rocks is a crucial issue in many deep underground projects, e.g. underground repositories for radioactive waste, CO2 sequestration, enhanced geothermal systems, oil and gas production, etc. Rock fractures are typically rough-walled, and surface roughness appears to have first order control on the mechanical and hydraulic behavior of single rock fractures (Boutt et al., 2006).It is well known that the mechanical aperture of a rock fracture is usually larger than its hydraulic aperture, due to fracture surface roughness (Tsang and Witherspoon, 1983). However, for naturally fractured rocks including numerous discontinuities, the effects of this reduced hydraulic aperture in local fractures on macroscopic fluid flow and solute transport in complex fracture systems still remain unclear. Many previous studies assumed identical hydraulic and mechanical apertures in discrete fracture network models for simplicity (Min et al., 2004; Zhao et al., 2011). Therefore, the main objective of this study is to evaluate the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks, by employing the empirical models that relate the hydraulic aperture to the mechanical aperture."

Jan 1, 2015