Search Documents

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

"In 1989, improved milling and recoveries resulted in a record production of 7 722 200 Ib Nb2P5 at the Niobec Mine. At the beginning of 1990, proven and probable reserves stood at 11 952 000 tons grading 0.65% Nb205. This year, the world steel market has slowed and as a result, niobium consumption is down. Consequently, production at the mine dropped 14% for the second quarter.IntroductionThe Niobec Mine is located approximately nine miles northwest of Chicoutimi, Quebec, (Fig. I). After ten years of production, the Niobec Mine is the only operating niobium mine in North America and the second largest producer of niobium in the world after Brazil.The Niobec Mine is a joint venture held equally by Teck Corporation and Carnbior. Teck Corporation operates the mine while Cambior is responsible for marketing and selling the niobium pentoxide concentrate (Nb2P5).The deposit was discovered in 1964 following an airborne radiometric survey in search of uranium. However, mining of the deposit did not begin until 1976. The initial production capacity of 1500 tons per day was increased several times to the present capacity of 2450 tons . The deposit is considered as an ample source of pyrochlore concentrate for at least 15 years at the present production rate.Niobium, also known as columbium, is a greyish-white metal used primarily as an alloy in various steels and other metals. The use of niobium in alloys heightens tensile strength and improves corrosion resistance while at the same time reducing the weight of the alloy. Niobium is also used in the fabrication of steel for the aerospace, automobile, and oil and gas pipeline industries. Although substitutes for niobium exist, their use often results in diminished performance and net cost increases."

Jan 1, 1990

"Line Creek Resources Ltd. produces three million clean tonnes per year of metallurgical and thermal coals for the international market. The mining operation, which is located in the mountains of southeastern British Columbia, produces coal from four pits by conventional truck and shovel methods.The South Pit, which has been in operation since J982, has a benched highwall 490 m in height. Shallow dipping coal seams at the base of the syncline formation will be exposed in the highwall over the next four years of pit life. The first of these seams, which will measure 500 m in final highwall length, was exposed in J994. An auger, powered by a 1250 hp engine capable of cutting 2.2 m diameter holes, was brought on site in J994 and has proven to be a successful means of recovering coal from the J3 m thick seam.This paper covers the background to the selection of an auger mining method to recover highwall reserves together with the geotechnical and methane considerations for this approach.IntroductionLine Creek Resources Ltd., a wholly owned subsidiary of Manalta Coal Ltd., owns and operates the Line Creek mine. The operation which consists of four active pits, a processing plant, and rail loadout is located in the southeastern coal fields of British Columbia. Figure 1 shows the general area.The coal bearing sequence at the mine is preserved on the east and west limbs of a major syncline. Up to twelve mineable coal seams, ranging in thickness from 2 m to 15 m are contained in the formation. Within the pits the seams are stratigraphically consistent and structurally undisturbed, except for small-scale thrust faults that create multiple repeats of the seams."

Jan 1, 1995

By Kenta Kusunose, Dadang Sundana, Ahmad Munib Fikry, Yosuke Unno

PT Smelting has operated the Mitsubishi Process in which feed materials are charged into the S- furnace through top lances using a pneumatic conveying system comprising 6 feeding tanks (S-Feeding Tanks). Each S-Feeding Tank was designed as a batch machine and had been operated in a batch mode so that feed materials are conveyed 70% of the operating time (conveying time). An S-Feeding Tank was revamped in August 2016 in order to attempt to achieve 100% conveying time during operation, aiming to reduce the furnace draft fluctuations and melt temperature fluctuations leading to reduced copper losses to slag and refractory wear on the sidewall in the melt zone. After two-year operation with some adjustments and modifications, it was concluded that the new system works as expected. During scheduled major shutdown in November 2018, the same modification was applied to all other 5 feeding tanks as the first one, while several modifications other than the S-Feeding system were also conducted for the purpose of expanding the capacity of the smelter. INTRODUCTION PT. Smelting (PTS) Gresik Copper Smelter and Refinery is located 30 kilometers north of the city of Surabaya, East Java major port. PT Smelting equity partners are Mitsubishi Materials with 60.5%, PT. Freeport Indonesia with 25%, Mitsubishi Corporation RtM Japan Ltd. with 9.5% and JX Nippon Mining and Metals corporation with 5.0%. PTS was established in February 1996 and started commercial operation of the Mitsubishi Process in 1999. The Mitsubishi Process is a unique technology which connects 3 stationary furnaces, namely the Smelting furnace (S-furnace), Slag-Cleaning furnace (CL-furnace) and Converting furnace (C-furnace) by covered launders. These features result in savings in manpower and energy, and make the process more environmentally friendly since there is no ladle transfer of melt. Figure 1 illustrates the outline of the Mitsubishi Process.

Jan 1, 2019

By L. Lamothe, C. H. The

"Pilot precipitator tests were conducted at Noranda's Horne Smelter in late 1978 to evaluate methods of improving converter dust collection efficiency. A bout 35 Nms/min. of converter off-gas were isokineticatly diverted from the converter flue to the pilot precipitator leased from Flakt (Canada) Ltd., consisting of three fields, one transformer-rectifier set per field and 77-m2 total collecting plate area. The effects of gas volume flow rate and conditioning the gas with sulphur trioxide and/or additional moisture were tested. II was found that gas flow rate and moisture level had the most pronounced effect on collection efficiency. Based on a techno-economic assessment of different options for improving converter Courell efficiency, waffle hoods and water sprays were installed on the converters to reduce air infiltration and increase the moisture level in the gas.BackgroundThe Horne Smelter of Noranda Inc. is situated in northwestern Quebec and, since the closure o f the min e in 1976, has been operating as a custom smelter. The concentrates treated at the smelter come from various mines with mixed sulphide ores , many o f them containing significant amounts of lead and zinc which makes dust collection in electrostatic precipitators mo re difficult than normal.As part of a continuing program on reducing smelter dust emissions, the No . 6 Cottrell was installed in 1972 up stream of Nos. 2 and 4 Cottrells (in parallel) in a n attempt to improve dust collection by increasing the over- all precipitator capacity ( Fig. I). However, it has never per formed a t its designed efficiency o f 94%. The average efficiency established in various test s was in the range of 60 – 65%."

Jan 1, 1985

By R. J. Mitchell

"A lest apparatus has been developed for obtaining the relations among confining stress, porosity and percolation rate for hydraulic sand backfills. The apparatus can also be used to evaluate internal drainage characteristics and the effects of partial saturation on percolation rates. The test apparatus, test procedures and typical test data are presented in this paper.IntroductionAlthough the standard percolation test has become an accepted method of evaluating the drainage characteristics of hydraulically placed tailings backfill, it is recognized that the test results require considerable interpretation due to the following factors: (I) The results can be markedly influenced by varying sample preparation procedures, which vary the amount of material segregation in the sample . In particular, a thin layer of slimes on the top of a sample can control the flow of water into the sample. Wall edge effects can also affect the test results. (2) The in-place porosity of the backfill is not duplicated in the test sample and empirical formulae must be used to estimate the variation of percolation rate with porosity. (3) Internal drainage characteristics and the percolation rate of partly saturated fill cannot be evaluated in the standard percolation test.In addition to eliminating these problems, the compression percolation test apparatus also provides additional data on the mechanical properties of the backfill. Compressibility (or bulk modulus) is measured at different stress levels during the course of a test and this information can be used in evaluating the usefulness of the fill in providing ground control and in limiting ground subsidence. The engineering design of mine backfill is becoming an important part of the over all design of underground mine operations. The design problems are sufficently different from conventional civil engineering soil mechanics problems that new test methods and design procedures are required."

Jan 1, 1981

By D. Laguitton

"Mathematics, process theory, process practice and computer applications are the main disciplines that contribute to developing useful techniques for computer simulation of mineral and coal processing plants. As in any multidisciplinary effort, communication or transfer mechanisms must be developed to facilitate the flow of experience between participants of different backgrounds. These mechanisms include written reports, verbal communications, workshops and transfer of computer programs. The SPOC project at CANMET is devoted to computer simulation and as such has addressed, or will address in the near future, problems inherent to methodology transfer. The first major output of the project was the material balance program, MATBAL2, which has been acquired by over 30 organizations. Program documentation, industrial workshops and summer student programs have been used to effect the transfer. This experience is discussed and the future outlined.IntroductionComputer simulation has become a common tool in many different fields of human activity during the past two decades, as illustrated in Figure 1. The total number of articles abstracted in Chemical Abstracts under the general subject entry of “Simulation"" has been following a pseudo-exponential growth since 1972 and was approaching 5000 in 1980, whereas no such entry was even used prior to 1967. This represents over a dozen papers published daily on the subject and should continue to grow to higher figures. Still, progress toward accepting modelling and simulation in mineral and coal processing has been very slow. It will be shown later that this slow acceptance is a cause rather than a consequence of the limited success of the various attempts made so far to draw unambiguous benefits from simulation applications. The real cause of the difficulties in fully accepting the new methodology lies in the multidisciplinary aspect of modelling and simulation, which does not suit the traditionally conservative approach that prevails in designing and operating large and costly processing plants."

Jan 1, 1982

By Brian E. Robertson

"This paper summarizes work carried out at the Dome Mine to mechanize the mining of narrow veins of less than 1.5 m in width by the introduction of new mining methods and specifically designed electric LHDs.Extensive mining trials have been conducted using sublevel blasthole, modified Avoca, and resuing mining methods. The introduction of the Microscoop and the Jarvis Clark remote, radio-controlled scooptram has increased mucking productivity.As a result of this work, additional narrow vein stopes are now being prepared for production. In the future, narrow vein stoping wil lprovide a greater percentage of the total mill tonnage.IntroductionThe Dome Mine, which is owned and operated by Dome Mines Limited, is located at Timmins, Ontario. Production has been continuous since 1910 and in 1984 was increased from 1814 to 2721 tonnes per day.At least six distinct ore types have been recognized at the mine. In general, these orebodies can be broadly categorized into wide and narrow deposits. The wide deposits are approximately lenticular in shape and vary in width from 10 m to 40 m. The narrow orebodies consist of quartz and quartzankerite veins ranging in width from a few centimetres to six metres. The average dip of the veins is 65 degrees.Since the I970s, mining activity has been largely concentrated in the wider orebodies using highly productive open sublevel blasthole and mechanized cut-and-fill stoping methods. With the demise of shrinkage stoping in 1975, investigations were initiated to develop new mining methods and introduce LHDs - truly designed for narrow orebodies. These investigations resulted in test trials of the sublevel blasthole, modified Avoca, and resuing mining methods. Consultations with equipment manufacturers and suppliers led to the development of the Jarvis Clark remote, radio-controlled electric scooptram and the introduction of the France Loader Microscoop."

Jan 1, 1986

By Gerardo Fuentes

Arsenic extraction from Chilean copper concentrates up to nearly 99% was achieved, using hydrothermal reactions. Arsenic appears in nature in more than 200 mineral species, being arsenopyrite (FeAsS), enargite (Cu3AsS4), and tennantite (Cu12As4S13) the most common species. In addition, arsenic is present in a large amount of copper concentrates, produced in northern Chile. Medical statistics show that in northern Chile, the amount of cancer to the lung, skin and bladder are the highest in the country. The latter situation, demonstrates the importance of studying metallurgical processes that do not generate atmospheric pollution. The hydrometallurgical processes such as hydrothermal treatment in autoclave reactors, do not produce gaseous emissions. On the other hand, the arsenic remains in solution from where it can be transformed in scorodite by widely known methods. Previous works about hydrothermal treatment of enargite have shown the feasibility of transforming the enargite of the copper concentrates into chalcocite or mineral species of the chalcocite family such as djurleite, digenite and for this reason enrich the concentrate in copper and pass the arsenic to solution. For this research, two Chilean copper concentrates were used, concentrate 1 with 5.5% arsenic and concentrate 3 with 1.8% arsenic. These concentrates were subjected to a complete chemical and mineralogical characterization. Later these concentrates were carry out to batch tests of hydrothermal treatment. Also, these concentrates were subjected to grinding to have different particle sizes. For the hydrothermal tests, a liter capacity Autoclave Engineer reactor was used. Characteristic of this reactor was the maximum temperature 350°C, 5000 PSI pressure, and 900 rpm agitation speed. Kinetic tests were carried out with the two concentrates maintaining the same solid: liquid relationship, the same agitation velocity and the variables studied were treatment temperature, time of reaction, concentration of copper in the solution and grain size of the concentrates. The conclusions of the study indicated arsenic extraction of the order of 93.98% from the concentrate 1 and arsenic extraction of the order of 98.74% from concentrate 3. After the hydrothermal treatment, the solids and solutions were characterized chemically, by electron microscopy and X ray diffraction. Also the solids were characterized by grainsize through a particle size analyzer (MICROTRAC). Results of batch treatment shows that arsenic can be release almost completely from real copper concentrates using this hydrothermal process and the next stage will be a scale up process in order obtain results for pilot plant design. INTRODUCTION Arsenic is an impurity that appears associated with copper minerals forming enargite, tennantite, tetrahedrite, and that due to the pyrometallurgical treatment either in conversion or roasting furnaces, it goes into the atmosphere together with the sulfur dioxide. A great quantity of literature can be found to eliminate arsenic or try to separate arsenic from copper. The methods used are mainly leaching processes with or without pressure (Padilla, Jerez & Ruiz, 2015) with different reagents like chloride media (Herreros, Fuentes, Quiroz & Viñals, 2003) or chloride media with sulphuric acid (Riveros & Dutrizac, 2008) or sodium hypochlorite (Mihajlovic, Strbac, Zivkovic, Kovacevic & Stehernik, 2007). It is known too that Chile is the first copper producer in the world and a great quantity of its minerals are in the north of the country, in Antofagasta.

Jan 1, 2019

By A. Paulin, J. Roth, S. Spaic

This experiment was carried out to see whether copper-iron ingots from Late Bronze Age hoards could have been produced by smelting ferruginous copper ores. Since ferruginous copper-ores are chalcopyritic, chalcopyritic concentrate from a present day copper mine was dead roasted in our experiment in lieu of a rich chalcopyritic ore. Charcoal was used as a reducing agent in the reduction of calcine (i.e., a product of dead-roasting), and quartz sand was used as a flux. Two separate metallic solutions, a copper-base and an iron-base alloy, were obtained as a result of two factors: the presence of carbon and the miscibility gap in the Cu-Fe-C system. The metallic melts appeared in a form of bigger or smaller droplets, enclosed by a molten slag which, during the cooling, solidified into metallic beads. The presence of both metals was noticed in the majority of the examined beads. It was therefore concluded that calcine consisted of an intimate mixture of oxides of both metals which were simultaneously reduced during the reduction process. Due to the miscibility gap in the Cu-Fe-C system, separate iron and copper regions were formed in the beads. In both regions, sulphide inclusions were found. The formed molten copper and molten iron solution were found to be saturated solutions. The metallographic analysis revealed the precipitation of iron out of copper and that of copper out of iron during the cooling and solidification of melts. The formed slag contained little iron and no copper oxide.

Jan 1, 2001

By Edward S. Bell, Frank Angebrandt

"Nuclear reactors must have very large heat outputs to compete with conventional sources and the only feasible applications are in the production of electric power or large quantities of process steam. This paper considers alternative fuels for electric power generation in Canada. In a publicly owned utility, nuclear stations are economic for base-load generation for unit sizes of 500 mega• watts or larger where competitive fossil fuel costs are higher than about 30 cents per million Btu. In British Columbia, Alberta and Saskatchewan, fossil fuels will continue to be in adequate supply at costs lower than 30 cents per million Btu and thus, except for the special case of Vancouver Island, power generation in Western Canada will continue to be the hydraulic and conventional thermal type. In Eastern Canada, fossil fuel prices are likely to be higher than 30 cents per million Btu and most utilities will be able to install units of 500 mw or larger, so that nuclear power plants will provide much of the base-load generation required. Base-load generation comprises about two-thirds of the energy generated by power utilities. By 1990, the total annual electrical energy load will be over 600 billion kwh, with two-thirds of this load in Eastern Canada. Allowing for additional hydraulic resources which may be developed in Quebec, British Columbia and Manitoba, hydraulic generation is forecast to provide a little more than a third of this electrical energy, nuclear generation a third and fossil-fuelled generation about a quarter."

Jan 1, 1969

By P. E. Auger, J. E. Gill

"The zinc deposits to be described are in Lemieux township a few miles south of the Tabletop mountains, in the central part of Gaspe peninsula, Quebec. Although they have not been worked, they constitute a potential source of zinc and lead and structurally are of considerable interest.GENERAL CHARACTER OF THE OCCURRENCEThe deposits are in sharp-walled quartz-carbonate veins and breccia zones carrying locally, and in varying amounts, sphalerite, galena, pyrite, marcasite, chalcopyrite, and specularite. Those so far investigated strike generally north-south, have steep dips, and cut through sediments of Lower Devonian age, mostly calcareous argillites or siltstones. Wall-rock alteration is negligible.BROADER STRUCTURAL FEATURESThe principal known occurrences are in the south-central part of a dome structure measuring 6 by 5 miles. The argillaceous sediments are overlain, on the flanks of the dome, by sandstones and lavas. These have been stripped from the central part of the dome, revealing the veins in the argillites beneath. The veins formed after the volcanics, but the fractures and breccia zones in which the deposits formed are confined mainly to the argillite series, presumably because of the greater strength of the lavas.The argillite series is cut by dykes, sills, and small stocks of diorite and acidic 'porphyries' that are older than the veins.THE FEDERAL HILL AREAThe distribution of known veins is shown in Fig. 1. The characteristic features of the veins are well illustrated by the Federal Hill area shown in Figs. 2, 3, and 4, and described below."

Jan 1, 1954

"In mills, metallurgical efficiency is important in every step of the operation through to the tails. Different problems which hinder metallurgical efficiency exist in different mills. One such problem occurred in the Bralorne mill at the tailings end of the circuit, where the washing efficiency of the filters was so low that serious losses in dissolved gold occurred.The new cyanide plant at Bralorne went on stream in August 1961. Test work done showed that: a flowsheet of grinding in water, jigging, thickening, agitating, followed by double filtration, gave satisfactory results and was more economical than a counter current plant. Two filters, 141 x 161, with approximately 700 square feet of filtering surface on each, were purchased and installed in series. Test work showed that this was ample filtering area for 500 tons per day.When the plant started up a density of 45% solids was maintained in the agitators, and a 20 ounce cotton dl1ck was used on the filters. Vacuum was between 23 - 25 inches. Under these conditions the filters would not work and only picked up a very slight skim of pulp. Various speeds were experimented with, 4 minutes per revolution being the most efficient. At this speed the thickness of the pulp on the filters increased to about 1/8”• It was therefore quite apparent that, under these conditions, the filters would not handle very much tonnage and the mill tonnage would have to be reduced drastically until the problem was solved."

Jan 1, 1967

By Frank Wright

"The Icon Sullivan Joint Venture ore deposit was discovered in June, 1965 by Messrs. Paul Benard, Bob Galipeau and Mac Watson working under the direction of Mr. Andrew J. Troop, as employees of the Icon syndicate. The deposit is located on the Waconichici River as the south end of Baie du Poste of Lake Mistassini, approximately 45 miles north of Chibougamau. Property acquisition and Winkie drilling was followed by a diamond drilling program to evaluate the deposit. Stripping of the open pit area connnenced in the late fall of 1966 and the first test sample of ore was shipped to Chibougamau in December of that year.Regular ore shipments to the mill of Merrill Island Mining Corporation Limited for concentration commenced May 25, 1967. Production to December 31, 1970 amounts to 42,960,000 pounds of pay copper.The ore is chalcopyrite in white quartz dolomite, and it contains a very small amount of precious metals. The quartz dolomite assumes a flat to gently dipping attitude and is associated with a graphitic argillite contact zone on both hanging and footwall sides, in dolomitic limestone rocks. There is practically no other sulphide present in the ore.During the summer of 1969 a series of pre-concentration tests were completed and a Wemco heavy media sink float plant was installed in late 1969 and early 1970. This pre-concentrator eliminates at least one third of the ore mined in the form of barren quartz dolomite prior to ore shipment by truck to the concentrator in Chibougamau."

Jan 1, 1971

By M. Leroux, C. J. Martin, S. R. Rao, J. A. Finch

"The effect of nitrogen on the flotation separation of sulphides from complex ores from Brunswick Mining and Smelting (New Brunswick) and Mattabi Mines (Ontario) was investigated. The most significant finding was enhanced pyrite floatability after as little as 3 minutes nitrogen conditioning. This was used in a novel sphalerite/pyrite separation process developed on the Brunswick ore. After aeration and Cu/Pb bulk flotation in air using xanthate the slurry was nitrogen conditioned, xanthate added and the pyrite floated in nitrogen. As an example up to 70% pyrite recovery with about 20% sphalerite recovery was achieved. Sphalerite was recovered from the pyrite tailings and the pyrite concentrate by copper-activation, raising the pH to 10 and floating in air. About 65-70% recovery at 35-40% Zn grade was achieved compared to 25% Zn grade by the conventional route. The process offers a promising alternative to current practice which seeks to depress pyrite at all stages. A possible mechanism of the effect of nitrogen is presented. INTRODUCTIONUse of gases other than air in froth flotation has been reported from time to time. [Podobnik and Shirley, 1982; Lin and Metzer, 1975]. Of all the gases, nitrogen would appear to hold the greatest practical promise because of its easy availability and chemical inertness. It is used in froth flotation in chalcopyrite-molybdenite separation [Redfearn, 1983]. The use of nitrogen in polysulphide chalcopyrite. this case is mainly to reduce the oxidation of a compound (Nokes reagent) used as a depressant for There is no reported use of nitrogen in the flotation of other sulphide minerals."

Jan 1, 1988

By Karl Houseley, Dr. Robert J. Chapman

"A gravity concentration process has been applied to ores from the Clogau Mine, north Wales, the Tyndrum deposit, central Scotland and an alluvial ore from Leadhills area of Scotland. In the case of the Welsh ore and the alluvial deposit the gold grains in the concentrate and tailings streams have been characterised in terms of their three dimensions.In the case of Welsh ore, the thickness of a gold grain has been shown to be the single most important factor in determining behaviour in a gravity concentration operation. Six indices were used to quantify the overall geometry of the gold grains and those which incorporate a thickness term have proven to be effective in predicting the destination of gold particles within the concentration circuit. It is proposed that the most simple of these, the Heywoods flakiness ratio, has potential for the control of milling operations as an alternative to the established practice of characterising the size of the mill discharge.The effect of grain geometry on the recovery of fine gold has been studied using Tyndrum ore. The recovery of gold by gravity concentration increased from 20% to 70% when the criteria used to design the milling operation was the prevention of over grinding of gold grains.The destination of alluvial grains in the concentration circuit did not show such dependence on shape, and this has been attributed to the effective classification of all the gold grains in the sample by fluvial action producing a population of similar geometric characteristics."

Jan 1, 1996

By Tim Robinson, Michael S. Moats, William G. Davenport, Andreas Filzwieser, Andreas Siegmund, Shijie Wang

This survey continues the long tradition of providing a snapshot of operating data from industrial electrorefineries. It is a supplement to previous surveys that were performed in 1987, 1991, 1995, 1999, 2001, 2003, 2007, 2010, 2013 and 2016. Analyses of current data and historical trends are presented. Examples of innovations to reduce costs, improve productivity, and improve quality are provided. In general, refineries continue to increase productivity while treating anodes with more impurities. INTRODUCTION This manuscript analyzes global survey data provided by operating copper electrorefineries. This paper continues a series of surveys of copper refining tankhouses that started in 1987 (Schloen, 1987, 1991; Schloen & Davemport, 1995; Davenport et al., 1999; Robinson et al., 2003; Moats et al., 2007, 2013, 2016). In this installment, data collected from 2015 and 2018 will be presented and analyzed. The 2015 survey data were presented at Copper 2016 in Kobe, Japan. This survey will continue the analysis of previous data to illustrate long term trends in copper electrorefining, which were originally presented at the Davenport Symposium in October, 2014 (Moats, Robinson, & Wang, 2014). Refineries who supplied surveys are listed in Table 1. Cathode production data from 2015 and 2017/18 (from surveys presented in 2016 and 2019) are provided to indicate which plants provided surveys and when. This manuscript presents operating data for ~6.5 million tonnes of copper production, which represents 30–35% of the world’s copper electrorefining production. The detailed survey results are available upon request from the corresponding author.

Jan 1, 2019

By P. D. Duever, P. J. Readyhough, P. L. Silveston

"The Plastojrost apparatus, developed by Ritter and Juranek in the 1960s has been modified primarily, to automatic temperature control. A limited investigation of carboniferous and cretaceous coal samples showed that both coals undergo the same changes when coked in the Plastofrost unit. Dilatometer plastic range and total dilatation correlated well with the Piastofrost plastic range for the carboniferous Appalachian coal, but not for the cretaceous western Canadian coal. Work to elucidate the characteristics of some western Canadian coals using the Plastofrost is in progress. IntroductionCoke quality is critically affected by the properties of the plastic phase in the coal-to-coke transformation. Since these properties exist in a coke oven and are not measurable, they are approximated by standard laboratory tests, such as free swelling index, plastometry, and dilatometry. Of particular interest to us is the anomalous behaviour of western Canadian coals of cretaceous origin. By many predictive methods, these coals should not produce coherent cokes. When coked in pilot scale test ovens, in fact, they produce cokes of good stability. They typically make up 20% of Japanese coking coal blends and are also used in South Korea, Mexico, Brazil, and several European countries. This anomalous behaviour has been studied in our laboratory<8.9.1O). Plastic properties or rheological tests examine just the external ramifications of the coal-to-coke transformation. To understand the process, however, microscopic examination of the coal and coke seems to be needed. The Plastofrost unit has been shown to be a convenient means to this end."

Jan 1, 1987

By R. Thierbach, W. Kahnt, Oberthür. T., D. Eisenburger, V. Gundelach

ABSTRACT: The ground penetrating radar (GPR) method was used in a platinum mine in Zimbabwe by members of the Federal Institute for Geosciences and Mineral Resources (BGR). The measurements were carried out in boreholes and drifts. Electromagnetic re?ections from a fault that consistently trends parallel to the mineralization zone permitted the mapping of the economically minable parts of the deposit. An introduction is given to the geology of the studied area and the application of the GPR method. The electrical parametres of the rocks are measured in situ, the GPR measurements are displayed with radargrams, and the visible structures are explained in illustrations.

Jan 1, 2010

By J. M. R. Carvalho, M. T. A. Reis, M. R. C. Ismael, M. J. N. Correia, S. M. C. Santos, J. M. Carvajal

A sulphide zinc concentrate (Zn-40%) has been leached in sulphuric and chloride media to optimize the conditions for the recovery of zinc and copper. Previous results showed that extractions of 95% zinc and 20% copper can be achieved in just one stage, after two hours of leaching at 80°C with a solution 0.5M in Fe2(SO4)3 and H2SO4 and a solid/liquid ratio of 5%. This work presents the results obtained in the leaching experiments carried out in sulphuric and chloride media using two and three crosscurrent stages and a countercurrent process simulation for a solid/liquid ratio of 10%.

Jan 1, 2008