Search Documents

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By C. Lapointe

"IntroductionTen years ago, when nuclear fission became practical, the element uranium, until then a not very desirable by-.product of the radium industry, became overnight the strategic material par excellence. One of the several important problems that had to be solved at that time was the rapid and precise determination of uranium in ores and concentrates.GeneralThe chemical analysis of uranium ores is a long and difficult business and is complicated by the presence in most ores of a large number of interfering elements. True, much progress has been made, during the past few years, toward simplification of the analytical methods, but the chemical determination still remains the job of a skilled operator. For this reason, the chemical method has been replaced, whenever possible, by a physical determination based on the measurement of the radiations emitted by the elements of the uranium family. There are several types of instruments suitable for these measurements, but of all the radiation detectors known to the physicist, such as ionization chambers, crystal detectors, scintillation, proportional counters, and the like, the Geiger-Mueller counters have proved to be the most satisfactory for routine determinations, because of their simplicity.The Geiger-Mueller counter is a very versatile instrument; it can be constructed to detect any type of radiation, corpuscular -0r electromagnetic. Here, however, we are interested in these counters because of their ability to detect the beta and the gamma radiations, both emitted by some members of the uranium family. The beta radiation is corpuscular, and is composed of fast electrons, while the gamma radiation is electromagnetic."

Jan 1, 1950

By Dan Currie, Tom Lamb, J. Coady Marsh, Gary Landry

"This paper describes the Cape Breton Development Corporation's experience with the Lovat M-300 tunnel-boring machine at the Donkin-Morien Mine. Between January 3 and December 21, 1984, the 7.6 m (25 It) diameter TBM advanced 3350 m (10 990 ft) . The authors will describe experiences with the machine and highlight the implications of tunnelling machines to underground coal mine development in Canada. IntroductionThe Cape Breton Development Corporation (CBDC) has recently completed the drivage of a 7.6 m (25 ft) diameter tunnel, 3.5 km (2.2 miles) in length , to access the Harbour Coal Seam at the Donkin-Morien Project. The tunnel was successfully driven with the first Canadian rock tunnel-boring machine (RTBM or TBM), designed and built by Lovat Tunnel Equipment, Inc. The initial mine development consists of the drivage of two tunnels to the first major coal seam. Future plans are proposed for the development of a 4 million tonne-per-year mine (Marsh et al., 1983, Gillman, 1982), which will require the drivage of a further two tunnels and could access up to four coal seams. The tunnel cross-sectional areas were designed to provide sufficient ventilation area and access for a production of 4 million tonnes per year."

Jan 1, 1986

By C. F. Chung, F. P. Agterberg

"Prediction of a variable sulphur content in Cape Breton seams is important for planning the production of a highgrade metallurgical coal. Two extrapolation methods (Kriging and a version of Universal Kriging) to predict sulphur content in blocks of coal before mining are presented and applied to the New Lingan Mine reserves in the Harbour seam. The uncertainty of the predicted values is expressed by using standard deviations. Some statistical results for the Phalen seam, which occurs about 400 ft below the Harbour seam, are presented for comparison. The two mathematical models consist of two sets of equations which have been used in computer algorithms. Some limitations of the present approach and possibilities for further statistical work are indicated."

Jan 1, 1973

By Grant J. Goddard

"The Iron Ore Company of Canada (IOC) has been in operation for over 30 years. Today, and in the future, technology and its application will play an ever more critical role in the company’s business success.The Carol Mining and Concentrating (CMC) division of IOC is energetically applying technology today to enhance performance and results, and is aggressively exploring opportunities to apply technology to support improved business results in the future.A critical area of focus is the application of technology to maintenance management performance. CMC has taken a “back to basics” approach to the fundamentals of maintenance management in 1995 and 1996. In parallel, the mine is aggressively implementing its Vision 2000 maintenance integration plan. This plan is targeted at levering the energies applied to sound maintenance management fundamentals as the company moves to a fully condition based maintenance approach.This paper discusses some of the strategies, key technologies and objectives of theVision 2000 maintenance integration plan at the mining operations of IOC."

Jan 1, 1996

By Paul R. Clark

Outline of Presentation ? Brief review of gasification and IGCC ? Polygenerationand its potential ? Why gasification today ? Major technology providers and their activities ? US initiatives ? Alberta Energy Resources and application of gasification ? CO2 management ? Advantages and barriers to gasification ? Conclusions

May 1, 2006

By 000-900-009-492

The flotation has been and is still the most widely used mineral concentration method. Because of its complexity, the flotation process required the development of robust control strategies which was facilitated by the introduction of on-line sensing instruments such as x-ray fluorescence (XRF) on stream analyzer (OSA), gamma density gauges and electromagnetic flowmeters. The interest in developing control strategies has persisted because the benefits to be gained in terms of improved metallurgical performance are substantial. As the flotation control becomes more and more difficult due to the emergence of low grade and complex ore cases, other control strategies have to be introduced. Froth based control is one of the emerging useful control strategy This paper will focus on the state of the art in the on-line froth characterization as obtained by numerical image analysis. The technology of machine vision provides a novel solution to several of the problems encountered in conventional flotation systems for monitoring and control, and constitutes a powerful tool for the investigation and interpretation of the effect of various flotation parameters as driven for the froth phases. Copyright @2001CIM

May 1, 2001

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By W. A. Gow

"In January of 1964, a group known as the Canadian Gold Metallurgists was formed with the backing of the managers of most Canadian gold mining operations. This organization is composed of about thirty mill superintendents of Canadian gold milling operations where the cyanidation process is in use, and one member from the staff of the Mines Branch, Department of Energy, Mines and Re-sources, Ottawa. The aim of this group is to bring together gold mill operators, and research and development people from both industry and government for the purpose of discus-sing common metallurgical problems, and deciding on what operational R and D efforts can be made to help solve these problems. Since the conception of this organization, this approach taken by the gold industry to the study of metallurgical problems has resulted in benefits to all operators, both by assisting them with problems peculiar to their own individual operations and by providing developments of general interest to the industry.This paper describes events leading up to the formation of the Canadian Gold Metallurgists, and how the group has operated since its formation. Examples of progress made toward the group's objectives are given, and possible future programs are discussed."

Jan 1, 1968

By T. Iwasaki

This paper points out two key elements in resource trade in general and the Canada-Japan relationship in particular. The first is that the advanced countries have a more important role than one would expect in the supply of resources in world trade. Canada 's dual role as a major resource supplier in conjunction with an advanced economy will continue to increase. The second point is the heavy reliance on foreign resource supplies in some advanced economies, particularly in Japan. Finally, as regard the future of the Canada-Japan economic relationship, particularly .in resource development, it is suggested that trade could be enhanced by an accelerated exchange of various types of resources between the two countries. These include natural resource commodities as well as the more abstract capital, technological and human resources.

Jan 1, 1978

By H. G. Stephenson, C. W. Gregory

"This article describes the methods used for pillar extraction in the Wilson Seam at Canmore Mines, Alberta. The Wilson Seam is extremely gassy and varies in thickness between 7 and 30 ft, with an average of 12 ft. The gradient varies from 5 to 30 degrees, with an average of 15 degrees. The seam was developed using Lee Norse miners to form pillars which the company intended to extract using the same machines. Before pillar extraction commenced, an abandoned and inaccessible mine 160 ft above the Wilson had to be drained of 360 million gallons of water. When this was done pillar extraction commenced. Conditions in the mine slowly deteriorated and after 6 months the decision to withdraw the continuous miners was taken. Slusher hoists were installed to replace the continuous miners, with the result that roof conditions and safety steadily improved."

Jan 1, 1972

By Don McColman

"Tires, although not always the largest single cost item in open-pit mining operations, will place in the top three, along with explosives and fuel. How this high-cost supply is controlled is dependent upon on an efficient tire program. The success of this program is, in turn, dependent upon the people who are directly associated with tires and their use, namely: the mine's tire personnel, the tire sales representatives and a technician for the rubber company. The technician will relay his observations and information received from the mine personnel back to the manufacturer with recommendations to overcome current problems .Haulage truck tire life and costs in a hard rock open-pit mine are governed and controlled by four important factors:I) Field control.2) Operating within manufacturer's guidelines.3) Different tire purchasing methods.4) Scrap piles.Field ControlPerhaps the most influential people involved in this program are those who live with the tire through every hour of its lifespan: the truck driver, the shovel operator, the dozer operator, the grader operator and the shift boss. Of these, the truck driver has the most control, in that he can drive over or around rock s as these situations arise. The loading area, the edge of the haul road and the dump account for most of the tire injuries.This is why shovel, dozer and grader operators must appreciate their influence on haulage tire life. Spillage cleanup must be ongoing and is not being done adequately if any of these operators are idle. The shift boss that drives by a rock on the road without removing it or calling for a cleanup has little recourse with the truck driver who runs over it-he has sanctioned the driver's actions by his own neglect."

Jan 1, 1986

By Ish Grewal

"Batch centrifugal gravity concentrators, which produce very high ratios of concentration, have become common place for recovering free gold within milling circuits. Their effectiveness has proven to be especially useful in recovering finer gold particles. The knowledge related to testing, modeling and scale-up of these systems has been well established over the recent decade mostly due to the efforts of the late Dr. Andre Laplante.Gravity separation technologies such as jigs, spirals and shaking tables can provide the increased mass yields required for minerals that occur at higher concentrations than gold, however their effectiveness tends to diminish at finer particle sizes. The development of high mass yield centrifugal concentrators has provided the opportunity to be able to recover a wide range of minerals at finer particle size classes when compared to the more traditional gravity concentration devices. These concentrators also provide additional benefits such as smaller unit footprint and automated operation.This paper discusses the background, current practices and future applications for high mass yield centrifugal concentrators in base metals, sulfides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.INTRODUCTIONGravity concentration, one of the oldest mineral beneficiation processes, has evolved over the decades and continues to play an important role in modern mineral processing operations. The development and growth of froth flotation in the early part of the twentieth century led to a decline in the importance of gravity concentration. However, gravity concentration continued to be used for ores that are difficult to beneficiate using froth flotation; such as tin, tungsten, niobium/tantalum, iron, industrial minerals and oxidized coal. In recent decades, many operations have begun to employ a combination of both gravity concentration and froth flotation Since flotation relies on surface chemistry and gravity concentration relies on specific gravity differences, putting these techniques in series provides today’s metallurgist with unprecedented opportunities to maximize grade and recovery of many of these minerals."

Jan 1, 2009

? The Mining Association of British Columbia (MABC) was established through an Act of Parliament in 1901 ? The MABC represents the interests of B.C.?s ? Coal and mineral mining companies ? Smelting companies ? Advanced stage development projects ? Key areas of work: ? Environment, Health and Safety ? Policy & Government Relations ? Knowledge and Information Services

May 1, 2008

By J. B. Scott

"A computerized cost estimating program developed with the use of the Lotus 1-2-3 spreadsheet program has produced dramatic savings in preparing estimates for operating costs, equipment fleet size and manpower requirements for underground mines.The program is used by Dynatec to support its consulting engineering projects, particularly feasibility studies. The 'first principles' approach is used to prepare detailed estimates under direct labour and supplies categories and maintenance costs for each mining operation . User notes have been developed to guide the estimator and ensure appropriate consideration is given to the specifics of the particular mine.A typical case history is illustrated and the ease by which alternatives and sensitivity analyses can be prepared is demonstrated. IntroductionHistorical MethodsMining engineers have used one or a combination of methods to prepare operating cost estimates for new or existing mine s. Operating companies have access to historical cost data and generally use this for preparing estimates. Consulting engineers do not usually have direct access to such information and must rely on mining companies (the present or previous clients); publications (text books, equipment manufacturers manuals, CMJ reference manual, etc.); annual reports (applicable to public companies); previous studies (to be used with caution as conditions change from mine to mine); and first principles (the subject of this paper), for cost information:Definition of First PrinciplesA first principles approach to cost estimating considers individual primary work elements of an operation. Quantities of work items are developed from the mine plans, production rates, geographic and physical layouts etc. The knowledgeable estimator, assisted by experienced operations personnel, can assign appropriate resources (equipment, labour, supplies and services) to each work element and establish productivities. Completion of the cost estimate is then largely arithmetic."

Jan 1, 1988

By C. A. Godden, T. N. Atkinson

Metallographic techniques developed from studies of corrosion films and electroplated coatings on aluminum alloys, are discussed. These methods, the result of work at the Naval Research Establishment, give extremely flat fields at the interface despite the large difference in hardness, in cases where electrolytic polishing could not be used. Techniques to overcome the similarity in refractive index of immersion oil, aluminum ox1d~, and mounting plastic are also considered, as are methods for improving visual and photographic contrast in areas of interest. A device for marking specimens is also de-scribed. ELE•CTROLYTIC polishing is inapplicable in the study of surface films on aluminum, whether corrosion films or electrodeposits. Mechanical procedures must there-fore be followed. Sample flatness and edge retention are of paramount importance. Special measures are required in the study of oxide films, because of the close proximity of the refractive indices of aluminum oxide, mounting plastic, and immersion oil.

Jan 1, 1962

By Willemijn Husslage

Tata Steel Group At a glance ? Part of the Tata Group ?Tata Steel Group: ?Fortune 500 company ?Top 10 global steel producer ?Annual crude steel capacity of 28 million tonnes ?More than 80,000 employees ?Manufacturing operations in 26 countries across 5 continents ?Serving customers all across the globe ?Turnover 2009-10: $22.8 billion

May 1, 2011

By Pascal Lesagel

Life Cycle Assessment (LCA) is a holistic environmental assessment tool that allows the compilation and evaluation of the inputs, outputs, and potential environmental impacts of a product or service throughout its life cycle, from cradle to grave (i.e., from resource extraction and transformation to final disposal, including production and use stages). The relevance of LCA for the mining industry is twofold. First, the mining industry has a role in providing the LCA community the data that allows subsequent evaluations of the life cycle environmental impacts of primary materials such as metals, as well as the environmental comparison of the downstream products of the mining industry with other competing materials for specific uses. Second, the mining industry can use LCA in order to evaluate the environmental impacts of its activities, identify their environmental hotspots and compare the impacts of available technical options. For example, the environmental impacts of different extractive and processing technology can be compared through the use of LCA. This latter use of LCA by the mining industry is less common. This paper discusses the use of LCA to compare sulphidic tailings management options. The paper also presents some of the LCA research challenges that still have to be addressed to increase the relevance of LCA results for the specific context of mining activities.

Nov 1, 2008

By M. H. MacLeod

"IntroductionTHE ORE PASS raise system at the H.B. mine as contracted by the Patrick Harrison Company consisted of two raises 6 ft. by 10 ft. in section •at 60 degrees to the horizontal. No. 88-88 raise, the longer of the two, was a straight raise 690 feet long, with access only from the bottom. In addition, this raise had two branch knuckle-backs only one of which was driven by. the Patrick Harrison Company. The other, known as 88-89 raise, was 540 feet long with knuckle-backs at 280 feet and 410 feet. Its access, also, was from the bottom (see Figure 1)."

Jan 1, 1954

Mineral resource development activities impact the health and well-being of many people, from workers, to families and surrounding communities. In the decade up to 2010, mining revenues increased from 6% to 14% of Australian GDP, and minerals contributed 55% of total exports, with a growth in mining employment from 1% to 1.7% of the national workforce (Connolly and Orsmund, 2011). The growth in Australia?s minerals operations is mostly located in remote areas, or in rural communities with a limited population. As a result, operations have increasingly implemented long distance commuting (LDC) programs, often called ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO), as a staffing strategy to meet rapid industry growth in locations with limited local populations. The rapid expansion of the minerals industry has resulted in considerable public debate about the benefits and costs to all sectors of Australian society. In response to the concerns of constituencies from many parts of Australia, the Minister for Regional Australia, Regional Development and Local Government, The Hon Simon Crean MP, asked the House Standing Committee on Regional Australia on Tuesday 23 August 2011 to inquire into and report on the use of ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO) workforce practices in Regional Australia. The recently published report highlights the national interest and the diverse opinions about this practice in Australia. Resource extraction companies have developed several options to meet the accommodation requirements of their long distance commuting workforce. In this paper, initial results are reported from an ongoing survey of FIFO (and other non-residential) resource industry workers (n = 286) in the Australian resource extraction industries. The purpose of this study was to better understand how accommodation arrangements may impact on the health, wellbeing and job satisfaction of non-resident workers; and to attempt to find a relationship between different accommodation variables and workforce wellbeing and retention. In doing this it investigates evidence for the linkage between accommodation factors, hours of work, health, well-being, job satisfaction and job retention in the LDC work force.

Aug 1, 2013