Search Documents

By K. A. Lewandowski

Agglomeration of ore used in heap leaching allows for the immobilization of fine particles that would otherwise migrate and cause permeability problems in the heaps. For copper ore, binders are needed in order to make stable agglomerates. However, the majority of binders break down when introduced to an acidic environment, allowing fine particles to be released from the agglomerate surfaces. These particles migrate through the heap impeding solution flow, leading to a decrease in metal recovery rates. The authors have developed a series of testing procedures to determine the acid resistance of several binders. Only five binders were shown to be acid resistant in soak tests, decreasing fines migration by up to 93%, compared to tests which were agglomerated with leach solution, raffinate, as a binder. Flooded percolation column testing also showed that these binders were able to reduce the "slump" of the ore by up to 82% and increased the hydraulic conductivity by up to 90%, when compared to agglomerating with leach solution alone. The use of binders in the agglomeration of copper ore also showed no negative effects on the bacterial populations throughout a leach cycle.

Jan 1, 2007

By N. Schreithofer, M. Aspiala, R. Serna

The novel attachment timer apparatus presented in this paper serves as a diagnostic tool that allows the detection of changes in bubble-particle attachment probability and therefore floatability caused by alterations in the chemical environment and particle properties. The apparatus consists of six identical capillaries where bubbles with defined size are produced simultaneously in a measurement chamber. The bubbles at the capillary tips are placed in contact with the submerged particle bed for specific time periods, controlled with the help of automatic actuators. The advantage of the instrument is that hundreds of bubble-particle contacts can be measured automatically within a short time period. Microscopic pictures of each measured bubble are taken while recording the movement of the bubble before, during and after contact with the solid particles. The recorded pictures can be used to determine the actual bubble size and its corresponding deviation, and to detect the attachment of particles. The attached particles are collected in a detachable chamber for subsequent characterization. Furthermore, the device is portable and can be taken to the mineral processing plants for quick evaluation of particle-bubble attachment efficiency with particles and process water sampled directly from real processes.

Jan 1, 2017

By W. S. Urbanski, A. L. Devernoe, R. W. Stuart, M. S. Walker

"Although many investigators have successfully achieved separations using variations of a concept wherein particles are buoyed upwards against gravity in a magnetically attracted fluid, none have succeeded in separating fine particles in a manner that is practical tor mineral beneficiation. This paper describes laboratory tests and preliminary economic analyses for a new mineral separation process which provides enhanced magnetic buoyancy and separation capabilities. The process provides a means of gravity separation in a regime where conventional gravity separation is inadequate; that is for small differences in mineral densities and for very fine particles. Although early interest centers on gravity separation, the process has also been successfully used for precise magnetic separation.Tests were conducted on a variety of mineral mixtures, ore samples and concentrates including; a sphalerite ore, pyrochlore ores and concentrates, cassiterite pre-concentrates, a chromite pre-concentrate, and heavy mineral placer samples. Separations requiring high discrimination between fine particles narrowly different in density or weak magnetic properties were obtained. Of particular interest is the ability of the process to concentrate or remove oxide minerals or gangues, especially silicates. Potential applications are discussed."

Jan 1, 1985

By D. H. Wilson

"This paper examines the increasing need for mechanical-electrical people within the industry and some of the reasons why such a shortfall exists. It is suggested that, in part, it is image related. The present industry-education relationship in addressing the situation is examined and some thoughts are expressed on how these may be built on, in order to help solve the problem of attracting people to this critical area.IntroductionAs a long-time proponent of plant engineering and maintenance as a management function, I would like to review the progress made by the industry/ educational approaches in satisfying the needs in that area. In doing so, I would like to make the following points:1) that there has been an accelerating shortfall of mechanical-electrical people relative to the needs of the industry;2) that the condition will probably get worse before it gets better; ,3) that the past industry I educational approaches to alleviate the problem have met with limited success; and finally4) I would like to review some of the things being done and consider how these efforts might be extended."

Jan 1, 1981

By Richard J. Kolada, Ian R. Muirhead

"This paper reports on a CANMET-funded examination of less conventional underground coal mining methods. These methods are documented and those that show the most promise for application to western Canadian conditions are discussed in detail.IntroductionIn recent years, mining considerations and economics have encouraged a transition from underground mining to surface mining. However, a change in market conditions or the development of superior underground mining methods may reverse this trend . Should this happen, the industry must be quick to respond and have information available on the latest developments of underground mining technology. In time, deposits of high-quality coal, which are easily accessible to surface mining, will be depleted and a change to underground mining methods will require consideration. The economic transition point between surface to underground will be a major determinant in maintaining a competitive edge. For these reasons, it is important to keep abreast of improvements in underground mining methods. To meet this objective, CANMET awarded a research contract to Monenco Consultants Limited, to investigate unconventional underground mining methods that show a potential for western Canadaoi. This paper presents the results of this investigation."

Jan 1, 1988

By G. Langlands

"R. Tenbergen Is this flotation machine suitable in the flotation ofInco ball mill discharges where we have a coarse feed at 60% solids?Reply Experience has shown that there is not a significant increase in the wear life of these machines when handling coarse material (8 mesh) at 60% solids. A common practice in Europe is shut down on the week-ends.The material is allowed to settle and on start-up an injectic of air for 15 seconds is sufficient prior to start-up. At,mining we put our unit in the middle of a bank of 44 cells and in order to ensure severe sanding we shut the aker cell down while the remaining cells kept running. After 20-25 seconds of air the cell started without trouble.P. Mahant Is there a build-up inside the impellor shaft housing? Falconbrige Ltd.Reply There is no sand build-up but rather a scale build-up which due to a flexing action frees itself periodically. Part of the design of the machine permits a water injection into the shaft housing to free any build-up. This is done in Europe during the week-end shut down."

Jan 1, 1984

By Michel Gamache

This paper describes a system that manages and assigns vehicles in real-time in an underground mine. Each dispatching decision takes into account the traffic on the road segments of the mine network, whether bi-directional or unidirectional, and ensures that each LHD (Load-Haul-Dump Vehicle) arrives in the right orientation at loading and dumping points. Such systems can be used for two main purposes: 1) as a strategic planning tool and 2) as a real-time managing and optimising system for operations. Using a simulator in conjunction with the fleet management system, it is possible to accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. Moreover, when used in for real-time dispatching, routing and scheduling of vehicles, the system can optimise production with respect to various assignment criteria such as minimising the cycle time or minimising the deviation from an optimal production plan. Dispatching, routing, and scheduling are handled simultaneously, taking into account the mine status, operational constraints, and all available information.

May 1, 2001

By D. P. Fenton

The Phelps Dodge El Paso Rod Mill produces approximately 2.4 million pounds per day of copper rod from a casting and rolling operation. The newly formed rod is treated to remove mill scale and oxides using a sulfuric acid and hydrogen peroxide solution which is bled periodically when the copper concentration reaches 30-35 g/L. The bleed solution is heated to 75° C to destroy the residual peroxide. Copper is then recovered in a 270 cell EMEW electrowinning plant. Clean acid is also regenerated in the EMEW plant and is returned to the rod cleaning circuit. The EMEW plant commissioned in January 2006, has two operators and replaces a copper sulfate plant with fourteen operators. The EMEW plant has a capacity of 1700 kg/day of cathode copper at 2.1 kWh/kg copper deposited. The electrowinning plant operates in closed circuit with the rod mill returning up to 2600 kg/day of sulfuric acid resulting in zero discharge. Use of dimensionally stable anodes (DSA®) ensures that the acid quality is maintained in the closed loop operation. The operating conditions, performance and plant experience of the EMEW copper and acid recovery plant are discussed.

Jan 1, 2007

By E. Roman E.

A novel anode slime purification process was developed and tested at pilot scale in the Chuquicamata Refinery. The process consists of three main stages: First, an atmospheric alkaline leaching at 90°C, under controlled pH and ORP operation parameters where metalloid impurities are preferentially removed from the anode slimes with high efficiency. In a second stage, alkaline washing of the mud leached with addition of reducing agent, with the intention of reducing the silver of the AgCl to metallic silver releasing the chloride, and finally, copper and other remaining impurities are leached out in mild conditions (60°C, one hour in sulphuric acid). In a side process Se, Te, and Sb are recovery with high efficiency from the alkaline liquor as chemical grade products. The global balance shows a high mass loss yielding a final product with high precious metal and low impurities content showing advantages in both a technical and economic point of view with a clear environmental sustainability. This treatment allows either the direct sale of the purified anode slimes or its pyrometallurgical treatment to obtain metal doré without emissions of Se, Sb and As. Chemical mechanisms for this novel process are also described.

Jan 1, 2007

By E. M. Córdoba

The effect of the Fe3+ lFe2+ redox couple on the chemical and biological dissolution of chalcopyrite was studied. All the tests were carried out in stirred flasks with 100 mL of a ferric/ferrous sulphate solution, in the absence or in the presence of bacteria (iron- or sulphur-oxidizing) and at low (35 DC) and high (68DC) temperature. The initial redox potential was controlled between 300 and 600 m V Ag/ AgCI and silver was used as chemical catalyst. The results showed that the oxidizing action of ferric ion on the chalcopyrite was controlled, in all cases, by nucleation and precipitation of jarosites on unreacted particles. The tendency of Fe3+lFe2+ solutions towards equilibrium favours the activities of both ions to be equal. Consequently, the dissolution rate was faster at relatively low redox potentials (between 400 and 500 mY) than at high values (600 mY). In this sense, the presence of ferrous ion in the system is a key factor to control hydrolysis and precipitation of ferric ion. Unlike jarosite, the elemental sulphur produced during dissolution of chalcopyrite was porous and did not act as a diffusion barrier.

Jan 1, 2007

"Background:The recorded coal production in Nova Scotia from 1863 to 1980 was 390, 000, 000 short tons. This extraction was associated with an estimated 60,000,000 short tons of discarded material. This mining discard and coal washing plant reject are located in numerous, varying sized dumps throughout the mining areas. Approximately 70% of these dumps are in the Sydney coal field region of Nova Scotia.The coal content of these dumps varies from 10 to 30% coal with an average of 18%.Energy Costs:The explosion of energy costs in the mid-1970 's greatly increased the sale price of thermal coal which made recovery of coal from some of the dumps economical. The environmental spin-off of these operations will be the rehabilitation of the dumps upon cessation of the coal reclamation operation.Cape Breton Development Corporation, the owner of most of the dumps in the Sydney coal field was receptive to an approach by Selco of reclaiming coal from their dumps. The technology to be used, had been developed by an associate firm in the United Kingdom on similar mine dump situations."

Jan 1, 1983

By S. Koski, M. Schmalzel, D. A. Jacobson, S. Crosby, P. Cook, M. Mular

"Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product.The MP1250’s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint."

Jan 1, 2012

By J. D. Stinnette

Traditionally, airflow requirements for diesel equipment operating in underground environments such as mines and tunnels were determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations(s) or determined empirically from known quantities. In some cases, utilization factors were further used to adjust (reduce) the total airflow calculations for a diesel equipment fleet. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is currently a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. Tier IV engine standards mandate a reduction of DPM and NOx of approximately 95%, but can ventilation rates at mines with Tier IV equipment (or equivalent) really be reduced by a factor of twenty? This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and examines how they can be applied in determining a reasonable ventilation rate for Tier IV compliant equipment operating in subterranean environments.

Aug 1, 2013

By Andrew D. Lapworth

The use of geological and grade models has been standard practice in mine design for many years now, with a wide range of software available to create and analyze the models. Although geotechnical parameters are also of vital importance for mine planning, there has been very little in the way of commercially available systems for integrating geotechnical data into the mine planning and design process. Sirovision is a new technology based on digital photography for automated, safe and accurate 3D mapping of geological and geotechnical features in rock faces. Datamine has integrated this capability into its product range so that Sirovision becomes an integral part of day-to-day face mapping, mine geology and geological / geotechnical modeling in both open pit and underground mines. This results in improved fragmentation for loading, hauling and processing, and for open pits local geotechnical conditions can be taken into account to improve slope design and control. This paper describes some of the ways that geotechnical modeling can be used to create more refined and cost effective mine designs and then discusses the role of Sirovision in enabling the raw data required for such modeling to be collected quickly, safely and reliably.

May 1, 2007

By H. Tokuichi, H. Ohta, K. Sato

A physical separation technique of tantalum capacitors from waste print circuit boards is in a development phase in Japan. A tantalum capacitor consists of an exterior coating of resin (epoxy resin) mixed with silica fillers and a sintered tantalum compact, the latter of which is impregnated with manganese dioxide (MnO2). In this study, we developed a process to recover tantalum oxide from tantalum capacitors by roasting, fluidized-bed separation, and hydrometallurgical treatments. Our aim was to recover tantalum oxide with high purity from waste tantalum capacitors. In this process, the exterior resin was selectively decomposed by roasting without oxidation and pulverization of the sintered tantalum compact at a proper temperature. Furthermore, the decomposed resin with silica filler on the surface of the sintered tantalum compact was mostly removed by fluidized-bed separation. The surface of the sintered tantalum compact was cleaned by ultrasonic irradiation in an acid solution to remove the MnO2 paste as well as residual Ag paste and silica filler. The impregnated MnO2 in the sintered tantalum compact was leached as Mn(II) ions using acid solutions via the reducing effect of tantalum metal to recover purified tantalum oxide.

Jan 1, 2014

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By Barry W. Schmitke, J. M. Marino

"Cigar Lake Mining Corporation is presently operating an underground test mine in northern Saskatchewan, with a view to developing a high grade uranium deposit. The mining test is intended to demonstrate that the innovative mining methods designed are safe and economical. Two vertical mining methods are considered for the test:• box hole boring from the lower level;• blind boring from the upper level.In both cases, it is anticipated to freeze the ground before excavation to ensure hole stability and limit the inflow of water. Special care will be taken to minimize radiation exposure of personnel.Remote controlled equipment will be used where applicable.The access to the orebody was an important component of the test. After shaft sinking to a depth of 500 m, development work commenced at the 420 level in fractured sandstone which was grouted to restrict the inflow of formation water. The drifting continued in a section of poorly consolidated sand, clay and sandstone; this area was frozen to allow stabilization prior to excavation. At the 480 level relatively little water was encountered in the altered basement gneiss and grouting was not necessary; however, extensive ground support was required in the soft ground areas."

Jan 1, 1992

By M. Abumiya, N. Onodera

"The synthesis of large scorodite particles in non-ferrous metallurgical industries usually requires a high-cost operation involving heating and high-pressure autoclaving. To overcome these obstacles, an atmospheric-pressure process for scorodite synthesis (DMSP®) was developed, in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. This process gives scorodite of good crystallinity with particle sizes as large as 15-20 µm. The solutions used for scorodite synthesis in the DMSP® are prepared from various residues containing arsenic from non-ferrous smelters. The solutions may be contaminated with Cu, Sb, and Bi, for example, and therefore the effects of such impurities on the formation of crystalline scorodite need to be investigated. In this study, the effects of Cu, Sb, and Bi contaminants on the formation behaviors of scorodite particles in the DMSP® were investigated systematically.INTRODUCTIONThe synthesis of crystalline scorodite (FeAsO4·2H2O) is a suitable method for arsenic (As) stabilization and storage of As-containing by-products such as flue gas dusts in non-ferrous smelters. It is expected that the formation of large, highly-crystalline scorodite particles would be an ideal method for avoiding the release of arsenic to the environment. Generally, autoclave methods under pressurized oxidation conditions at temperatures above 100°C have been used for the formation of arsenic minerals such as scorodite. However, the autoclave method requires sealed vessels that are resistant to high pressure, heat and acids. This process is also unfavorable on account of the high construction expenses, and high running costs as a result of vapor heat loss. Processes for synthesizing scorodite under atmospheric conditions at temperatures below 100°C which do not need an autoclave have therefore been extensively investigated (Demopoulos, Droppert, & VanWeert, 1994; Demopoulos, 1996; Demopoulos, Lagno, Wang, & Singhania, 2003; Droppert, Demopoulos, & Harris, 1996; Filippou & Demopoulos, 1997).Recently, Fujita et al. (Fujita, Taguchi, Abumiya, Matsumoto, Shibata, & Nakamura, 2008a, 2008b, 2009; Fujita, Taguchi, Kubo, Shibata, & Nakamura, 2009; Fujita, Taguchi, Shibata, & Nakamura, 2009) developed a new method for producing large scorodite crystalline particles with improved filtration and washability properties at normal atmospheric pressure and temperatures below 100°C. In the new method, oxygen gas (O2) is blown into solutions containing a high concentration of arsenic ions (As(V)) and ferrous ions (Fe(II)). The Fe(II) ions were subsequently oxidized to ferric ions (Fe(III)), resulting in the formation of large scorodite particles. High supersaturation of solutes such as Fe(III) will result in excessive nucleation, and the formation of poorly crystalline phases. The scorodite formation must therefore be conducted in a manner that avoids the critical supersaturation level being exceeded. It is supposed that the oxidation of Fe(II) to Fe(III) by O2 gas in the new method suppressed the supersaturation of Fe(III) during scorodite formation. The low Fe(III) supersaturation resulted in formations of highly crystalline scorodite particles of size of around 20 µm. In June 2008, based on the developed process described above, DOWA began experiments to verify the industrial capability of a plant with a capacity of 30 MT/month of As. It was successfully proven that it is possible to produce crystalline scorodite industrially on a commercial scale. This process was named and trademarked as DMSP® (Kubo, Abumiya, & Matsumoto, 2010)."

Jan 1, 2012

By Y. X. Li, L. R. Xiao, S. Gong, S. S. He

Porous copper and porous copper based alloys with controllable pore structure have been manufactured successfully by sintering evaporation process. This process consisted of mixing copper or copper based alloys with NaCl powders, hot pressing and final high-temperature sintering to evaporate the filler material of NaCl powders. NaCl was eliminated completely during vacuum sintering, and strong metallurgical bonding in the walls was achieved. The pores’ structural parameter (pore size, shape, and direction) and porosity can be controlled effectively. These porous copper and porous copper based alloys with controllable pore structure have great potential in many fields. Including heat dissipating materials, heat absorbing materials, chemical catalyst carriers, electromagnetic shielding materials, filtering materials, damping materials, silencing materials, battery electrode materials. INTRODUCTION The development of porous materials began in the 1960s. The research of activated carbon with high specific surface area made porous materials enter the stage of material research (Belyakov et al., 2008; Ferey et al., 2008). With the rapid development of science and technology, porous materials play an important role in material research, and gradually become an indispensable part of the material research field (Wu et al., 2012). The research of porous materials has gradually extended to metal, ceramics, plastics and glass and other fields. It has been successfully applied in many fields, such as functional materials, industrial production, aviation, medical materials, biochemistry and electronics, which fully shows that porous materials have considerable development prospects. Porous silicon, plastic porous materials and glass porous materials are the most widely used in the field of non-metallic porous materials (Capelle et al., 2012). Compared with non-metallic porous materials, metal porous materials have developed rapidly in the late 1980s and become new materials with good mechanical properties and excellent physical properties. Porous metal materials have many advantages, such as large specific surface, small specific gravity, good silencing effect, high stiffness, high electromagnetic shielding performance, good shock absorption performance, etc (Li et al., 1999; Ferey et al., 2008). Among its many applications, metal porous materials can be used as both functional materials and structural materials. In some cases, metal porous materials have dual functions and structures. It is a multi-purpose engineering material with excellent performance. At present, porous copper, porous aluminium and porous nickel are the most concerned materials (Chen et al., 2002; Yang et al., 2017; Liu et al., 2018). The preparation methods of porous copper and copper-based alloys mainly include self-propagating high temperature synthesis (SHS), capsule-free hot isostatic pressing (CF-HIP), spark plasma sintering (SPS) (Kvanin et al., 2008; Takahashi et al., 2008; Zhang et al., 2014). However, these methods can not accurately control pore structure parameters (including pore size, shape, orientation, distribution, etc.). In porous materials, pore structure plays an important role in the overall performance of materials. In order to control pore structure parameters accurately and optimize material performance, it is necessary to explore and develop new preparation technology. In this paper, the sintering evaporation process (SEP) was introduced for the preparation of porous copper and copper-based alloys. The core process of the preparation method is hot pressing and evaporative desalination. Hot pressing can make the pore orientation consistent. Evaporative desalination can ensure the complete removal of NaCl in the form of vapor in a short time, thus eliminating the corrosion of residual NaCl on the matrix metal (Gong et al., 2011).

Jan 1, 2019

By Ki-Bok Min, Bona Park

"In spite of the applications of DEM models to emulate the elastic modulus, Poisson’s ratio and strengths of isotropic rock in laboratory scale, extensions to anisotropic rock and larger engineering scale still have many challenges to overcome such as robust verification and validation against observed field case. In this study, a discrete element modeling was performed in order to represent a transversely isotropic rock such as shale, and the upscaled model was applied to foundation and borehole problems using PFC2D. The applicability of the upscaled rock mass model was verified by an analytical solution. The DEM modeling of stress redistribution induced by an applied surface line load compares well with Boussinesq’s isotropic solution and anisotropic solution given by Bray. The borehole model with a circular opening under biaxial stress was compared with both isotropic and anisotropic solutions resulting in good agreement. The abilities of DEM model to investigate the micromechanisms accounting for complex macroscopic behaviors and to predict the macroscopic behavior are discussed.The results demonstrate that DEM modeling has the potential to be applied to anisotropic rock mechanics problems on larger engineering scales such as wellbore stability problems especially in shale formations. Furthermore, the effect of anisotropy modeled through this study may be able to explain failure behavior of anisotropic rock encountered frequently in real cases.INTRODUCTIONAnisotropy is prevalent in various types of rocks, especially in shale that contain a set of parallel bedding planes. These weak planes in various forms are sources of large deformation and low shear strength and contribute significantly to the anisotropic behavior of rocks (Amadei, 1996; Cho et al., 2012; Kim et al., 2012). As elastic and strength behavior of anisotropic rock is substantially different from that of isotropic rock, proper consideration of anisotropy is of great importance. There is extensive of experimental evidence showing the anisotropy of shale. Niandou et al. (Niandou et al., 1997) analyzed the plastic deformation and failure mechanisms of Tournemire shale were highly dependent on the orientation of bedding planes. Cho et al. (Cho et al., 2012) presented various deformations and strengths of Boryeong shale obtained from laboratory experiments. Fjaer and Nes (Fjaer and Nes, 2013) performed uniaxial and triaxial compressive strength tests using Mancos shale, and they observed that the shear sliding along the planes of weakness before the occurrence of a major failure can reduce the strength of anisotropic rock. The recent research has demonstrated that the anisotropy of rock is an important consideration in rock engineering."

Jan 1, 2015