Search Documents

By M. P. Amsden

"Ecstall Mining is a wholly-owned subsidiary of Texas Gulf Sulphur at Timmins, Ontario. The mill tonnage is 10,000 tons per day of two different ores, a copper zinc ore and a silver lead zinc ore, producing about 2400 tons of concentrates per day. These are as a copper concentrate, a high silver zinc concentrate, a low silver zinc concentrate and a silver-lead concentrate. For flotation recovery a very fine grind is required, about 80% minus 325 mesh and the concentrates produced are 40% minus 10 microns.The thickened concentrates are pumped to the filter floor for filtering and drying. The filtering and drying section is separated from the flotation section by a wall and is controlled from a dryer control room by one operator.Two operating panels are located in this control room. One contains stop-start controls for the thickeners, filter motors and vacuum pump motors, and stop-start controls for dryer feed conveyors and dryer product conveyors to concentrate load-out bins, as well as ammeters for conveyor drive motors. Dryer throughput is regulated by Merrick Type L weightometers located on the dryer discharge conveyors and recorded on tons per hour strip charts.The second panel contains the temperature strip charts, furnace drive ammeters, scrubber and exhaust gas controls, burner controls and panel alarms for the four dryers.Filtered concentrates are dried in Nichols-Herreshoff, multiple hearth, dryers consisting of nine hearths (zinc) and seven hearths (copper and lead). There are two dryers for handling zinc concentrates and one each for copper and lead concentrates. The dryers are heated by burning natural gas. Each zinc dryer handles 1,000 t.p.d. and the copper and lead dryers 750 t.p.d. each.Multiple hearth dryers are unusual in the base metal mining industry and the reasons for selecting them in preference to rotary dryers are as follows:1) The concentrates could only be filtered to 15 to 17 percent moisture. These sloppy filter cakes would be extremely difficult to handle in rotary dryers."

Jan 1, 1972

By Y. Kocaefe, S. Afshar, D. Kocaefe, Z. Kunt, C. Allaire

Interaction of aluminum with silica based ceramics Jose M. Soto, Jeffrey D. Smith, William G. Fahrenholtz. Department of Ceramic Engineering University of Missouri-Rolla Rolla, MO 65409-0330 USA ABSTRACT Interactions between A356 aluminum (Al-Si alloy) and dense fused silica (FS) riser tubes used for low-pressure casting of aluminum alloys were evaluated using a sessile drop approach. The tubes have a short service life, but cost and thermal shock resistance make them an effective solution. The main problem encountered during use is the reaction of aluminum with silica to form alumina and silicon, which causes failure. Tests have been conducted on as-fired (uncoated) and modified (coated) tubes. Experiments were carried out in a horizontal furnace at 1225°C under argon to minimize the effect of the aluminum oxide on the interactions at the alloy-silica interface. Images of the drop were acquired and contact angle values were estimated for uncoated and coated samples, but no significant differences in the contact angles were observed. Scanning electron microscopy revealed the presence of cracks at the interface between the reaction zone and the unreacted silica. The presence of reaction products (silicon in the reacting alloy and aluminum in a reaction zone between the alloy and the unaffected silica) has been confirmed using energy dispersive spectroscopy. A two layer coating system was found to be effective in reducing penetration of the aluminum alloy. The interactions between bed media and aluminum have been studied under static and dynamic flow conditions. An experimental system was set up simulating a small filter. Desired flow field can be created around alumina particles and velocities can be adjusted. A mathematical model was developed to predict the velocities, and this was validated using data from a visualization study. The interaction zone on the surface of the particles was analyzed with optical microscopy and SEM. This paper presents the study and compares the results under static and dynamic flow conditions.

Jan 1, 2004

By C. Barnett

"The mill at Noranda Mines Limited, Geco Division in Manitouwadge, Ontario went into production in 1957 treating 3,500 tons per day of copper, zinc, silver, lead ore. It was not until 1964, however, that the zinc concentrate drying plant was constructed. In 1970, milling capacity was increased from 4,000 to 5,000 tons per day. The zinc content of the ore is quite variable so that the tonnage of zinc concentrate dried varies from 200 to 650 tons per day.The drying plant was designed to dry 25 tons of zinc concentrate, dry basis, per hour from an initial moisture of 8.5% to a final moisture of 2%. Major components were selected so that capacity could be increased to 35 tons per hour with minor modifications.The rotary dryer is a Hardinge type ""XH-12"" with a diameter of 80"" and a length of 50 feet. The all welded construction shell is 1/2 inch thick mild steel plate with 3/4"" thick reinforcing bands under the tires arranged for operation at a slope of 1/2 inch to the foot. The 3/8"" x 12"" radial flights are welded to the shell. There are no flights in the last ten feet of the shell in order to reduce dusting. This unit is driven by a 50 HP motor through a Hamilton type CD250 double reduction helical gear speed reducer. The shell speed is 5.8 RPM.The standard Peabody horizontal air heater has a rated capacity of 10,000,000 B.T.U. 's/Hr. The combustion chamber is lined with high temperature refractory brick and is air cooled. The conical outlet section of the air heater is lined with insulating fire-brick. The burner is a type AT wide range mechanical atomizer fired by a type ""CR"" gas-electric ignitor.The Bunker ""C"" fuel is supplied by a Compower duplex pumping, heating and straining unit, including tank hotwell, Powertronic oil line heating system with a 550/24 volt transformer."

Jan 1, 1972

By K. Blower

"Since there was no representative from Wesfrob Mines Limited, the information on their infra-red concentrate drying operation, which had been prepared by Mr. K. Blower, was presented by Mr, Dorland. Mr. Blower, in submitting the information, emphasized that their objectives in this operation were (a) to guarantee less than 90%, of flow-moisture in their copper concentrates and thus satisfy marine shipping regulation• and (b) to minimize capital costs, The infra-red dryers have satisfied these objectives.To control final moisture in the copper concentrate, current practice is to preheat the filter cake with steam in the disc filter hood and then conveyor-0r7 the concentrate with infra-red calrod heaters. The application of steam aids the system as follows:1) Improves vacuum pump efficiency.2) Lowers viscosity of filtrate (increased temperature},3) Preheats the cake prior to radiant heating. (150°F)The hot cake discharging from the filter ranges from 10.6 to 10.9% moisture. After radiant heating the moisture level is reduced to 8.5% - 9.7% depending on production rate. Further moisture loss occurs during conveying and transferring to the stockpile for a final shipment moisture ranging from 8.1% to 9.5%. Production rate is frail J to 5 dry short tons per hour.1) #23 Conveyor 18"" flat belt covered from filter discharge to transfer point with 7 heaters end-to-end. Drive - Reeves Vari-Speed, 31:4 ratio, type 332-10-18, class ""D"", driving through a 24:1 ratio Dodge reducer. Speed of Conveyor - 3,9 feet per minute to 19.6 feet per minute. (Speed has been established and is not changed as a rule from the present level of a1:out 15.)2) #23 Conveyor 24"" wide, 20° troughed belt covered with 21 heaters, end-to-end from loading point, Speed - Constant at 54,2 feet per minute."

Jan 1, 1972

By A. Farzanegan, D. A. Lowther, A. R. Laplante

"Off-line optimization studies are often necessary to improve the efficiency of grinding circuits. These studies are primarily based on the mathematical modelling of processing units (e.g., ball mills and hydrocyclones) and computer simulations. To complete an optimization task, process engineers must possess skills and knowledge of different subtasks involved in such efforts, e.g., plant audit, laboratory tests, and data analysis. Such know-how can be in part provided by Knowledge-Based Systems (KBSs). One such system, being developed in C Language Integrated Production System (CLIPS), is presented here, with focus on the estimation of ball mill selection functions for the purpose of both diagnostic and simulation, and its use for the optimization of ball size. Some of the interpretation and diagnostic rules will be presented, as well as grinding kinetics and classification data likely to fire them.IntroductionSince the late eighties there has been a growing trend in applying Knowledge-Based Systems (KBSs) to mineral processing [Meech 1990, Bearman and Milne 1992). Table l lists some KBS (often referred to as expert systems) applications that have been used mainly as tools for improving on-line monitoring and control of grinding circuits. However, there has been fewer attempts to add the symbolic processing powers of KBSs to conventional off-line grinding simulators. Figure 1 shows a relatively standard procedure to perform an off-line optimization study [Napier-Munn and Lynch 1992]. In brief, a typical program includes taking representative samples from a number of streams, running laboratory tests on collected samples, estimating model parameters which describe physical processing units (e.g. ball mills and hydrocyclones) validating model predictions and using models for simulation trials. One inevitably needs to be familiar with concepts of process modelling and simulation as well as various computer programs to be able to complete all steps of the study. Much of this ""expertise"" can be captured by KBSs, given their inherent capabilities for symbolic knowledge representation and manipulation."

Jan 1, 1997

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-ehalcopyrite core interlayered pyrite-sphalerite-galena (pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyritequartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone I) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (II and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone I, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F, fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By K. Lambrych

Hydrometallurgical equipment used to extract and refine copper and other metals is exposed to extremely corrosive chemical environments. These systems must be fabricated from materials that are durable against corrosion, meet exacting mechanical requirements, and perform economically over the life of the mineral processing plant. In several recent large hydromet projects, fiber reinforced plastic (FRP) has been shown to provide equal if not superior durability relative to alternative materials of construction. This paper will compare corrosion performance and cost of plant equipment fabricated with corrosion resistant alloys, rubber lined steel, and FRP made with Epoxy Vinyl Ester thermoset resins. Case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory-based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment. Specific examples from projects such as El Boleo, Long Harbour and others will be used to demonstrate how the versatility of FRP allows for remote fabrication of durable corrosion-resistant large-scale equipment for hydrometallurgical refinement of copper and other metals. INTRODUCTION Fiber reinforced plastic (FRP) began to emerge as a material of construction for corrosion service in many industrial processes in the late 1950s because of its ease of use and overall performance. Corrosion resistant (CR) FRP, as an alternative construction material to alloys, rubber and tile linings, grew steadily in following decades. The aggressive operating conditions associated with hydrometallurgical processes typically require materials of construction that can withstand acids and acid chlorides at temperatures up to 90°C, sometimes higher. Common metallic materials of construction, such as carbon steel, are not compatible with these conditions. High nickel alloys are capable of meeting performance requirements, but often at a high cost. In many cases FRP mining equipment based on epoxy vinyl ester resin (EVER) offers durability, long service life and lower maintenance costs. Through demonstrated performance and decades of case histories, more and more design engineers are confidently specifying FRP as the material of construction for new mineral processing equipment.

Jan 1, 2019

By Simon Houlding

"Part 1 (CIM Bulletin, August 1991) of this article identified the limitations of the traditional modelling methods and demonstrated the approximations and errors introduced by their application to complex mining situations. The objective of Part 2 is to describe the evolution of new, proven technology which eliminates these deficiencies and provides precise and practical alternatives. These promote the use of realistic geological and mining shapes and eliminate altogether the rectangular approximations of traditional methods. Limitations of the Traditional MethodsThe limitations of the traditional modelling method s (viz. simple block modelling, gridded modelling and their more recent variations) were discussed in detail in Part I . These methods are all based on the use of rectangular discretization to represent the boundaries and volumes of ore deposits and mining excavations. As a result they are unsuited to the representation of nonrectangular geological complexities such as folding, faulting and irregular surfaces . They are equally unsuited to the representation of realistic excavation limits, particularly in the case of underground mining.Recently these methods, with limited variations in technique, have been applied to increasingly more complex geological and mining situations. The resulting potentials for error and conflict within the modelling pro cess were demon strated in Part I . The effects can be summarized as follows:• volume and boundary approximations introduced by therepresentation of irregular three-dimensional boundaries andvolumes by rectangular modelling elements ; • geostatistical errors and conflicts caused by neglect of the relationships between grade estimates and the geometric/ spatial aspects of irregular volumes and associated observations (samples), including an inability to produce precise estimates with meaningful confidence limits;• a compounding of these effects by using rectangular element sizes other than the geostatistical optimum, and by using differentelement sizes within a model; and• general inefficiencies introduced throughout the modelling pro cess by the requirement to represent geology, grade distribution and excavation limits with a singular modelling method and model."

Jan 1, 1991

By R. B. Stein

"Countercurrent decantation circuits(CCD) are often employed in hydrometallurgy to effect solids-liquid separation in combination with a barren solution wash to reduce losses of valuable solution component(s) from the tails. Bechtel Corporation uses its BEMSIM flowsheet-modelling PC computer program to simulate a CCD circuit where the ""dirty"" wash solution contains significant amounts of soluble components. An algorithm successfully models this condition and is simplified to a single expression when the wash solution is a ""clean"" solution containing no solubles. The CCD calculation module is compared to operating data from uranium and nickel-cobalt CCD circuits.IntroductionHydrometallurgical process schemes have often relied on countercurrent washing methods to reduce soluble losses of valuable product in the tails. Commonly used equipment to effect this operation is a CCD circuit of N thickeners in series, where a slurry is fed to thickener I and a wash solution to thickener N; clear pregnant solution overflows thickener I and washed tails exit as underflow from thickener N. CCD circuits of this type are typically employed when the solids tend to slime heavily and where a filter is not economic.A typical CCD circuit usually employs from two to five thickeners and can employ either a ""clean"" washing solution of, say, pure water or else the hydrometallurgical circuit may generate a ""dirty"" barren solution containing an appreciable amount of soluble component which may be advantageously returned to the process as CCD wash solution. Various authors have treated the case for clean washing solutions (Svarkovsky 1977, Merritt 1970). For the case of dirty wash solutions, an algorithm has been developed to enable efficient modelling by the BEMSIM computer program, because the need for an accurate method to calculate soluble losses is required when performing an economic trade-off analysis of the value of product lost in the tails as a function of the number of thickeners."

Jan 1, 1990

By Neil Schofield

"The Pine Creek gold mineralization is associated with saddle reefs and quartz and quartz sulphide veining within the Enterprise Anticline. The anticlinal structure is complex and the mineralization was considered prior to development to be dominantly strata controlled. Gold grades vary up to 160 gin 1.5 m core samples with coefficients of variation in excess of three.The estimation of ore reserves for such a deposit must account for both the geological complexity and the extreme variability of gold grade.This paper describes the structural and variogram analysis of the gold grades and demonstrates the importance of incorporating the geological model in such an analysis. Variogram interpretation is greatly improved and greater insights into the finer geological structure areprovided. Part 2ofthis work presents the application of multigaussian kriging to reserve estimation for deposits with highly variable grade and which consequently demand highly selective mining operations. IntroductionThe Enterprise Gold Mine is situated some 220 km southeast of Darwin in Australia's tropical north. Gold is believed to have been discovered there in 1869 during the construction of the overland telegraph line.From 1894to 1915, some 75 000 ounces of gold were produced from 121 000 tonnes mined mainly by Chinese leaseholders. From 1906 to 1915, government-sponsored drilling led to the sinking of the Enterprise Shaft to 79 m and several drives were developed. Mining ceased because of war.Since late 1980, Goldfields Exploration Pty. Ltd. had explored on several mining tenements near Pine Creek under joint venture with the title holders, Enterprise Mines NL. This work culminated in the development of the current mine which opened on October 29, 1985.Feasibility studies to determine the economic viability of mining were based on ore reserves generated by project geologists using a sectional polygonal approach tuned to the interpreted geological control of the mineralization.The study motivating this two-part paper covers are-estimation of the recoverable reserve s using the geostatistical approach of multigaussian kriging developed at Stanford University, (Verly, 1984)."

Jan 1, 1988

By W. J. D. Stone

Discussions with people knowledgeable in the insulating material field revealed that materials on the market would be considerably improved if there was a greater meeting of certain very desirable criteria. Such criteria include: (1) the material should not burn, even at higher temperatures; (2) at an elevated temperature, the material should not give off toxic gases or produce smoke; (3) the material should have a low energy input; and (4) vermin would find the material unattractive. Theoretical discussions led to the conclusion that an insulating material made by foaming a mineral, preferably of a platy nature, with an inorganic binding system that could be converted to a rigid structure at low temperature would likely meet all the above requirements. It was also theorized that the use of microwaves in the converting stage would be beneficial in the creation of a cellular structure by aiding the foamer through creating vacules of steam. Talc was selected as readily meeting the theoretical mineral requirement and the material of Baker Talc Limited was used as the basic filler. The early results obtained led to an agreement between Americ Mines Limited and Baker Talc Limited pertaining to commercial production in a specific geographic area. It was recognized that due to the economics of shipping, the availability of the basic filler material should be geographically widely spread. Samples of materials were requested and many received from all over North America and one from Britain. Enough work has been done to show that they respond to the basic process in a similar manner as the Baker Talc material. From the data acquired, it is considered that the process is applicable for the production of loose fill insulation, moulded insulation for pipes and structural steel, ceiling tile, batts, sheet and for incorporation into other products such as various roofing board materials. Sufficient development has been done to enable a budget to be prepared for the construction and operation of a loose fill insulation plant.

Jan 1, 1979

By Hoeve. J.

"In the unconformity-type uranium deposit at Midwest Lake, mineralization is associated with extensive host rock alteration, which affects the metamorphic basement as well as the overlying Athabasca Group sandstones. Host rock alteration is manifested by (I) transformation of clay minerals [kaolinite into illite and chlorite (sudoile)]; (2) bleaching due to removal of hematite from the lateritic paleoweathering profile and the overlying red bed, Athabasca Group sandstones; (3) loss of coherence of the sandstone resulting from corrosion of quartz cement; and (4) in the immediate vicinity of high-grade ore, development of a clay envelope due to residual enrichment of clay minerals caused by massive dissolution of quartz. Clay mineral transformation and bleaching are the most prominent and the most widespread alteration effects, forming haloes that extend for several kilometres along the strike of the mineralized structure and also constitute distinct alteration pipes that rise f or several hundred metres above the unconformity to be truncated at the present top of the bedrock.Although the two haloes are largely congruent features, cross-culling relationship s indicate that clay mineral alteration represents an earlier phase in the history of the deposit than the large-scale bleaching that gave rise to the superimposed bleaching halo.Because clay mineral alteration and bleaching are intimately tied to the mineralization and extend well beyond the limits of the actual orebodies, host rock alteration may be used as an ore guide in exploration and drill-hole evaluation. In this application a third hydrothermal discharge centre was identified, as yet untested for are, which is located between the hydrothermal centres associated with the two known orebodies of the deposit.It is estimated that host rock alteration may enlarge a potential drill-target by a factor 10 - 20X. Information on the configuration of bleaching haloes can be obtained from systematic core logging, whereas diagnostic clay mineral alteration is readily identified by means of automated, quantitative XRD techniques."

Jan 1, 1984

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By J. C. Li, Y. Zou, L. He

"The effect of rock joints is significant in characterizing dynamic behaviors of discontinuous rock masses. To reveal the relation between the transmission coefficient and the contact situation of the joint surface, an experimental study on stress wave propagation across an artificial rock joint was carried out using a modified Split Hopkinson Pressure Bar (SHPB) apparatus. All the bars and specimens were norite cored from the same site, and one surface of the specimen which contacted to the transmitted bar was sawn with a number of notches to simulate the artificial rough joint. According to a wave separation method, two strain gauges were mounted on each pressure bar at a specific spacing, then the incident, reflected and transmitted waves across the joints were obtained from the test data. It was found that the contact situation of the rock joint surface makes a different on the wave propagation. Finally comparisons of the transmission coefficients with different contact area ratios and different joint thicknesses were made respectively. The results show the effects of contact area ratio and thickness of joints on wave transmission.INTRODUCTIONJoints affect the dynamic mechanical behaviors of the rock masses significantly. When propagates across the rock masses, wave usually attenuates in amplitude and frequency due to the presence of the joint as a discontinuous interface in the rock masses. Rock joints are the main factor that affects the behaviors and properties of rock masses. Many researchers have focused on the mechanical properties of rock joints under quasi-static conditions. Nowadays, the effect of joint dynamic properties on wave propagation across rock masses is gradually taken into account in theoretical and numerical studies.The effective contact area, joint roughness, and properties of the asperities and filling materials have been found to influence the normal stiffness of joints (Bandis et al. 1983). As suggested by the International Society for Rock Mechanics (ISRM), the roughness of the discontinuities can be generally characterized by large-scale “waviness” and small-scale “unevenness” (Brown 1981). Many researchers focused on the roughness of rock joints that affects the mechanical properties of rock masses and wave propagation. For example, Brown and Scholz (1985, 1986) presented theoretically and verified experimentally a closure model of contact between two random nominally flat elastic surfaces, which showed that the joint closure property depended both on the surface topography and material properties. Pyrak-Nolte et al. (1997) presented the quantitative aperture data for three-dimensional interconnected fracture networks, which were imbedded in intact opaque rock samples several centimeters in length, using x-ray computerized tomographic (CT) imaging. Fardin et al. (2001) systematically investigated the effect of scale on the surface roughness of rock joints and concluded that samples should be equal to or larger than the stationary limit for surface roughness to be accurately characterized on a laboratory scale or in the field. Zhao et al. (2006) conducted excellent ultrasonic tests across intact cement mortar specimens, singlefracture specimens, and two-fracture specimens."

Jan 1, 2015

By H. R. Kempthorne

"The Property of Bevcon Mines Limited, including a recently acquired adjoining south group, occupies an area of 2,625 acres in northeast Louvicourt township, Abitibi county, Quebec. It is situated 17 miles east of Val d'Or at the junction of provincial highways 58 and 59.Gold was first discovered in the area in 1931 by the late S. B. Jowsey on the present property of Buffaddison Gold Mines adjoining to the west. However, it was not until the winter of 1944-45 that diamond drilling encountered encouraging results on the Bevcon claims. During the period 1946-1948 a shaft was sunk to 1,000 feet and considerable development undertaken from the 500-foot to the 1,000-foot levels. Between 1947 and 1950 approximately 24,000 tons of dump ore and 48,000 tons of ore by stoping were milled at Perron Gold Mines. The favourable results of these tests prompted the decision to construct a milling plant at Bevcon. The mill began operating in July 1952, and presently has a capacity of 800 tons per day. In 1953 the shaft was deepened to 1,600 feet and is currently (1955) being driven to 2,225 feet.Total production of gold to the end of 1954 has been 101,024 ounces from the milling of 697,427 tons of ore of an average grade of 0·163 ounces per ton.GeologyThe Bevcon orebodies occur in a granodiorite stock which has an east-west length of approximately 4 miles and a maximum width of 1 1/2 miles. The property covers the central portion of the stock and its contacts with the Keewatin volcanics. Approximately one-third of the northern contact and one-half of the southern contact are contained within the Bevcon claims. The granodiorite has been cut by acid (feldspar porphyry) and basic dykes trending east-west. A younger diabase dyke, 300 feet wide, strikes northeasterly across the property 1,000 feet east of the shaft.The main ore zone, striking east-west, lies between the more northerly porphyry dyke and the north granodiorite-greenstone contact. It has been extensively sheared, fractured, altered, and mineralized by gold-bearing solutions. It is approximately 2,000 feet Jong from the west boundary towards the diabase dyke. The shaft is centrally located and passes through the south contact of the ore zone at the 500-foot level. The zone increases in width and trends northerly with depth, due to the porphyry and greenstone contacts having average dips of 80 degrees and 70 degrees respectively to the north. Thus on the uppermost or 500-foot level the width is 150 to 200 feet, and at the present bottom level at 1,600 feet the width is 400 to 500 feet.Another gold-bearing zone has been indicated 200 to 400 feet south of the main ore zone by limited surface drilling."

Jan 1, 1949

By X. G. Zhao, M. Cai, L. K. Ma, P. F. Li

"Crack initiation stress is one of the characteristic stress thresholds in the rock deformation process under compression. By analyzing AE responses of brittle rocks in uniaxial compression, a new method which is called cumulative AE hit (CAEH) method is proposed for determining the crack initiation stress. An advantage of the CAEH method is that the method removes the user's subjective judgment. To verify the CAEH method, uniaxial compression tests with AE measurement using 77 crystalline rock specimens were conducted. The test specimens cover eight rock classes with different mineral grain distributions. Crack initiation stresses of these specimens were determined by the proposed CAEH method and the LSR method, and the resulting mean crack initiation stresses determined using the two methods were comparable. In addition, taking one rock class with 20 specimens for example, the mean crack initiation stresses determined using the CAEH method and those from several established strain-based and AE-based methods were similar. Hence, the CAEH method can be used as an alternative method for crack initiation stress determination.INTRODUCTIONExperimental observations indicate that the failure process of brittle rocks is associated with crack initiation, crack propagation, crack damage and final strain localization (Brace et al., 1966; Bieniawski, 1967; Lockner, 1993; Wawersik & Fairhurst, 1970). Compression tests on cylindrical specimen are often used to characterize the crack development process. The crack initiation stress (sci), crack damage stress (scd), and peak stress (sc) represent important stress thresholds during the failure process of brittle rocks. Among the three characteristic stress magnitudes, sci is difficult to be determined objectively, directly from examining the stress–strain curves. Some researchers argued that sci obtained from laboratory compression tests is an important parameter for estimating the spalling failure observed in brittle rocks around underground excavations (Andersson et al., 2009; Diederichs, 2007; Martin, 1997). sci can also be used to estimate rock tensile strength and Hoek-Brown failure criterion parameter mi (Cai, 2010). Over the last 40 years, various strain-based methods have been proposed to determine the crack initiation stress in compression tests (Brace et al., 1966; Diederichs, 2007; Eberhardt et al., 1998; Lajtai, 1974; Martin & Chandler, 1994; Stacey, 1981). Nicksiar and Martin (2012) proposed a Lateral Strain Response (LSR) method for establishing sci for low-porosity rocks. Meanwhile, they also used different strain-based methods to evaluate sci of Äspö diorite, and the results showed that all strain-based methods gave acceptable crack initiation stress values. Subsequently, they utilized the LSR method to further investigate the crack initiation stresses in igneous, metamorphic, and sedimentary rocks in compression tests (Nicksiar & Martin, 2013). Compared with previously proposed strain-based methods, an advantage of the LSR method is that it removes the user judgment when interpreting sci. However, the use of the LSR method relies on accurate determination of scd and on having a polynomial fitting equation to find the maximum LSR value."

Jan 1, 2015

By W. N. Wallinger

The mine and concentrator of Cyprus Anvil Mining Corporation are situated in south-central Yukon, some 120 miles north of Whitehorse. The large lead-zinc concentrator employs conventional crushing and grinding , followed by differential flotation, to produce selective lead and zinc concentrates, as well as a mixed lead-zinc (bulk) concentrate. Since the commencement of operations in 1969, the concentrator has undergone expansions and modifications which have increased the capacity to 10,000 tons per day, and afforded some metallurgical improvements.

Jan 1, 1978

By J. Fujioka, Y. F. Gu, C. Cui, D. Ping, A. Sato, H. Harada

"A new kind of cast & wrought (C&W) Ni-Co base superalloys named as ""TMW alloys"" are developed recently for compressor or turbine disks of gas turbine engines in High Temperature Materials 21 Project at National Institute for Materials Science (NIMS) in Japan. These Ni-Co base superalloys combine the characters of two kinds of y- y' two-phase alloys (Ni-base and Co-18at%Ti alloys) and have higher tensile strength and creep resistance than C&W UNDIMET 720Li superalloy."

Jan 1, 2006

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Apr 1, 2005