Search Documents

The NorthMet deposit of PolyMet Mining is located in northern Minnesota, adjacent to the Iron Range. The deposit is polymetallic with values of Cu, Ni, Co, Zn, Pt, Pd and Au. The processing route selected for extraction of these values utilizes bulk sulfide flotation followed by hydrometallurgical treatment. The hydrometallurgical process has been thoroughly tested on the bench and pilot plant scale at SGS Lakefield Research. The major steps in the process are; ? Chloride-assisted total pressure oxidation for extraction of base and precious metals ?Thickening/filtration/washing of the barren residue from total oxidation ? Reduction and precipitation of Au, Pt, Pd from the oxidation solution ? Partial neutralization of autoclave acid using limestone ? Copper SXlEW for production of copper cathode ? Treatment of a portion of the raffinate from Cu SX to recover NilCo/Zn as either a mixed Ni-Co-Zn hydroxide or as separate Ni hydroxide, Co hydroxide and a Zn sulfate solution. ? Recycling of the remaining raffinate to the autoclave as coolant The process flowsheet, chemistry and bench/pilot plant test results will be reported in this paper.

Jan 1, 2007

By M. Honarmand, Z. Moezifar, H. Ranjbar

Abstract - The Sar Cheshmeh area covers an area of 640 km2, and is located in the southern part of the Iranian Volcanic-Sedimentary Belt. ETM+ images have been used for alteration mapping. The Crosta method was found useful for enhancing exposed areas containing hydroxyl and iron oxide minerals. However, field checking has shown that this method is not able to identify all the known areas of hydrothermal alteration. Many of these altered areas are also not clearly resolved in the geophysical data. In order to improve resolution of such areas, integration of remote sensing and geophysical data may be helpful. The Darrehzar Cu deposit was chosen as a control area. The data have been divided into two sets: explanatory and target variables. The explanatory data are Landsat hydroxyl and iron oxide images and airborne geophysical data (K, U, and Th total counts, and total magnetics). The target variables are rock geochemistry and ground geophysics. Data analysis and integration of geophysical and remote sensing data were performed using directed principal components. This technique is found to be useful for the delineation of hydrothermally altered areas with more confidence.

Jan 1, 2002

By S. M. Bulatovic, D. M. Wyslouzil

"This paper presents the results of a study of the effect of flowsheet configurations on metallurgical results and describes a general method for developing and optimizing flowsheets used in the treatment of massive sulphide ores. The flowsheet configuration can have a significant effect on recovery and selectivity between valuable minerals and gangue minerals. Placing of intermediate products within the flowsheet, positioning of various pretreatment units, such as conditioners or regrinding mills, and the ability of the flowsheet to cope with wide swings in the feed grade and composition are the major parameters that determine the optimum flowsheet configuration. The complexity of the flowsheet is largely a function of the ore itself and of the number of final, marketable products that have to be recovered from the ore. INTRODUCTIONTechnological ExpansionThe trend of past decades has been towards larger equipment and a better understanding of the chemistry of the flotation process. Despite appreciable progress in these areas little attention was given to the study of the actual configuration of the flowsheet, although the arrangement of the flotation equipment significantly affects the overall performance of the circuit."

Jan 1, 1989

By D. Thibault, A. Akhiate, M. Brochu, E. Braud

Cast martensitic stainless steels, 13%Cr-4%Ni, having carbon contents between 0.018 wt% and 0.067 wt% were normalized, air quenched, and tempered at two different temperatures (550°C and 610°C). Their microstructures were characterized by optical microscopy and X-ray diffraction (XRD). Macro and microhardness, tensile strengths, and impact resistance were quantified for each material and condition. Results show that the prior-austenite grain size is constant through the materials but the percentage of reformed austenite, contained in the martensitic matrix, depends strongly on the material chemistry and on the tempering temperature and on its duration. It is observed that, independently of tempering conditions, an increase in carbon content increases the material hardness and tensile strengths, whereas the elongation remains constant. In contrast, the results of Charpy type impact toughness tests show a different trend. The material containing the average carbon content (0.034 wt%) is significantly tougher than the two other alloys. Surprisingly, the toughness of the steel containing 0.034 wt% carbon was found independent of the reformed austenite content. It is thus concluded that carbon and reformed austenite contents are not the only parameters affecting the toughness of these steels.

Jan 1, 2014

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-I993. Part I, presented in the June, 1994 issue of the CIM Bulletin, gave a listing of thesis titles. Part II. which consists of edited abstracts of theses considered to be of direct application to mineral deposit studies and exploration. is presented under various themes as follows:A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothermal Gold Deposits. Other Gold Deposits and Related Studies:E. Magmatic Nickel-Copper, Platinum Group Element and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;G. Diverse Hydrothermal Deposit,>, Sediment-hosted CopperDeposits and Mississippi Valley Type Lead-Zinc Deposits; andH. Uranium-related studies, Evaporites and Exploration Geophysics.Abstracts related to themes A to F were presented in previous issues of the CIM Bulletin, abstracts related to themes G and H are presented in this issue.G. Diverse Hydrotbennal Deposits, Sedimenthosted Copper Deposits and Mississippi Valley Type Lead-Zinc Deposits"

Jan 1, 1995

By F. Boudreault, C. Hendricks, M. Scobie

Drilling accuracy represents an important quality control factor in minimizing dilution. Apart from geology, the factors governing drilling accuracy are largely within the control of the mine. Setup location and alignment, as well as actual drilling accuracy, can all be monitored toward their improved control. Trajectory deviation during drilling, although usually beyond the control of even the most experienced and conscientious driller, can be accounted for (if not full controlled) by down-hole surveying of blastholes prior to explosives loading. This paper reviews the available instrumentation for improved drill setup and recent field experience with several commercial systems designed for monitoring borehole deviation. It reports on a recent survey of 50 Canadian mines which use blasthole stoping and addresses the reasons for the apparent lack of interest in instrumentation: i.e. does this reflect a lack of awareness of the technology, perceived inadequacies in its performance or a predominant reliance on productivity (drilling and mucking) as a measure of operational efficiency? The survey findings supported the latter viewpoint and showed that very few Canadian mines operate drilling incentive programs that are related to drilling accuracy.

Jan 1, 1994

By Arash Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5 M tons. The underground mine has three active development panels and one longwall panel. The mining horizon is about 500 m below surface and strata liberate methane. Three surface-based blowing fans provide ventilation air. A ventilation survey and subsequent analysis was undertaken and a simulation model developed. Air heating during winter is essential to prevent freezing of pipelines and to lesser degree, for miner comfort. Air at all three intake shafts is heated using gas-fired heat exchangers. A strata heat study was conducted in one of the active panels to determine rock attributes. Tests included in-situ measurements of rock thermal conductivity and geothermal gradient. Continuously methane monitors have also been installed in an active development panel?s return drift. Ventsim ventilation software was used to aid the heat and contaminant simulation study. An exercise was also undertaken to gain some understanding of methane contaminant levels throughout the mine. It was further used to determine an adequate surface intake air heating rate and consequently the minimum natural gas consumption needed for winter intake air heating at the mine.

Aug 1, 2013

By J. Donovan

Underhand cut and fill mining is being planned for selected areas at the David Bell Mine where high ground stresses have resulted in particularly challenging mining conditions. In order to test the placement and performance of a variety of underhand cut and fill paste mats three different designs have been installed and extensively instrumented along the A-Zone 9C ore sill. The sill is approximately 87m long, 4.0m high, and 5.0m average width. The sill was broken into 3 sections each of which will contain one of the sill mat designs. The underhand sill will be mined 3.75mW x 4.0mH, allowing for some overbreak while minimizing the risk of the back span exceeding the design limit of 4.0mW. Each test sill mat includes pre and post-support and includes 0.5m (18?) broken muck mat placed along the sill floor. Upon developing beneath these mats quantitative and qualitative measures will be used to determine which design is the most suitable for application in underhand mining at David Bell.

May 1, 2007

By Yves C. Lizotte, Malcolm J. Scobie

Blast fragmentation is affected by the physical and mechanical characteristics of the rockmass as determined by geology as well as the explosive energy, the partition of this energy, the actual amount of energy transmitted to the rockmass, the blast geometry and the detonation sequence. This paper reviews studies of the influence of geology on blast fragmentation, particularly structure, i.e. the in situ or inherent fragmentation arising from rock discontinuities. Prior structural studies have mainly been limited to comparing equivalent diameters of the in situ blocks with the size distributions of the blasted material. No criteria exist to integrate structure into blast design. This paper reviews on-going studies of the blasted fragment shape and size observed in different rockmasses aimed at analyzing geological control over blasting. Digital photoanalysis was applied {o measure size and shape distributions, to correlate results with block size distributions and shape parameters of the inherent fragmentation. An integrated and comprehensive fragmentation assessment procedure which accounts for geological control is proposed. The potential of this research is to provide a greater understanding of the true contribution of explosives to fragmentation, the effects of fragment shape on system productivity and the reduction of blast-induced damage.

Jan 1, 1994

By X. Cao, P. Wanjara, J. L. Fihey, X-T. Pham, F. Mirakhorli

Single-pass hybrid laser-arc welding of 10-mm thick cast plates of CA6NM, a low carbon martensitic stainless steel, was carried out in butt joint configuration using a continuous wave fiber laser at its maximum power of 5.2 kW over welding speeds ranging from 0.75 m/min to 1.2 m/min. The microstructures from the fusion zone to the heat affected zone and base metal were characterized after post-weld tempering at 600°C for 1 hour. From optical and scanning electron microscopy examination, the fusion zone was observed to mainly consist of tempered lath martensite and some residual delta-ferrite. The mechanical properties including microindentation hardness, ultimate tensile strength and Charpy impact energy were evaluated in the post-weld tempered condition and correlated to the microstructures and defects. The ultimate tensile strength and Charpy impact energy values of all the fully penetrated welds in the tempered condition were acceptable according to ASTM, ASME and industrial specifications. The failure mechanisms during tensile deformation and Charpy impact loading were examined by scanning electron microscopy, fractography and optical metallographic analysis near the fracture origin.

Jan 1, 2015

By M. Kim, M. Ha

"The effect of red mud on the melting behavior of ferronickel slag was investigated by a laboratory-scale horizontal tube furnace. Melting and softening of slag samples fluxed with different amount of red mud was examined by in-situ visualization technique at temperature range from 1400 to 1550°C. FactSageTM 7.0 was used for the thermodynamic calculation of multi component system of ferronickel slag and red mud. Liquid phase area was extended to lower temperature by adding red mud indicating its suitability as a flux material. X-ray diffraction analysis confirmed the dependency of the phase changes on the red mud content. Microscopic observation by scanning electron microscope (SEM / EDX) clarified the phase transformations from olivine to spinel along with red mud additions.INTRODUCTION Ferronickel smelting by submerged arc furnace (SAF) is an energy intensive process performed at high temperature range 1500–1600°C. During the smelting process of saprolitic nickel laterite ore with a nickel content of 2.2–2.3 pct, a large quantity of ferronickel slag is being produced that account for 97 pct of ore charged. To achieve ferronickel grade of 15–20 pct Ni, electrical energy of 80 to 85 MW is used for the melting and reduction of nickel oxide (NiO) and iron oxide (FeO) in the ore (Rodd et al., 2010). Unreduced components, mostly MgO, SiO2 and partly FeO are removed from the furnace in a liquid slag form by a tapping operation. Due to the high melting temperature, forsterite (Mg2SiO4) based slag containing approximately 10 pct FeO requires typical process temperature of 1600°C. Flux in metallurgical process is a medium that decreases melting and operating temperatures while it increases fluidity of the liquid slags. Calcite and fluorite are examples of flux materials used for the ironmaking, steel refining and continuous casting process. Oxide systems based on CaO - CaF2 - SiO2 - Al2O3 - MgO cover most of the slag composition in ferrous metallurgy accordingly. Crucial operating factors for ironmaking and steelmaking slags are basicity (typically CaO/SiO2 ratio), viscosity and impurity levels. These are extensively controlled by the fluxes. General metallurgical fluxes such as limestone, dolomite and calcium fluoride are abundant in nature and supplied to steel mills at low prices. Meanwhile, in copper flash smelting process, silica is supplied with copper concentrate to remove iron oxide (FeO) generated from sulfide oxidation. FeO - SiO2 binary system formulates eutectic area at 25–38 pct of silica that has low melting temperature below 1205°C. Fayalitic system (Fe2SiO4) that has low viscosity (0.1 Pa·s) (Park et al., 2011) facilitates easy separation of slags from molten sulfide mattes. Recently, copper plants actively utilize recycled raw materials as a flux. Various recycled glasses are ground and fed to copper smelting process as a partial replacement of silica ore. Applying industrial wastes to smelting processes is advantageous since the operators can reduce the production cost remarkably. Not to mention the consumption of recycled materials can ultimately minimize the environmental risks and the waste management costs. The authors, therefore, investigated the reasonable waste materials that can be effectively used for ferronickel smelting process. Prerequisites for potential fluxing materials are non-recyclable property, low transportation cost and excellent performance as a flux."

Jan 1, 2017

By D. K. Sarkar, Jiawei Xiong

"Self-assembled monolayers (SAM) on the aluminum substrates are used as the adhesion promoter between two aluminum substrates when bonded with the adhesive in adhesive bonding technology. Traditional surface analysis tools are not capable of identifying the presence of SAM on a surface; therefore, EIS has been used to determine their presence on the aluminum substrates. In this study SAMs have been deposited on aluminum using the monomer of (3-Glycidyloxypropyl)trimethoxysilane (GPTS) organosilane. AA6061 aluminum alloys substrates were chemically cleaned with NaOH and HNO3 to remove the native oxides, followed by immersion in silane solutions. In a second method, SAMs were prepared by applying a spin coating of silane solution to the samples. The prepared SAM coated aluminum samples were analysed by EIS in the three electrode corrosion cell using a diluted alkaline solution. The impedance of the SAM coated aluminum is found be higher than the as-received aluminum. It has been also observed that the open circuit potential (OCP) of the SAM coated aluminum is higher than the as-received aluminum. Both elevated values of the impedance and OCP confirm the presence of SAM on aluminum.INTRODUCTIONSelf-assembly (Schreiber, 2000) is defined as the spontaneous formation of complex hierarchical structures from pre-designed building blocks, typically involving multiple energy scales and multiple degrees of freedom. Generally speaking, SAMs are created by the chemisorption of ""head groups"" onto a substrate from either the vapor or liquid phase followed by a slow organization of ""tail groups"" of a molecule. Typically, head groups are connected to a molecular chain in which the terminal end can be functionalized with groups such as –OH, –NH2, –COOH, or –SH to vary the wetting and interfacial properties (Chauhan et al., 2007; Ulman, 1996; Vashist, Lam, Hrapovic, Male, & Luong, 2014). Though there exist several methods to prepare SAM (Chauhan et al., 2007; Chen, Yang, & Zhang, 2014; Cho, Park, Jon, & Choi, 2007; Igor Luzinov, 2000; Reis, de Melo, & Costa, 2006; Song, Zhai, Wang, & Jiang, 2006; Sugimura, Hozumi, Kameyama, & Takai, 2002; Vashist et al., 2014), the two methods vapor phase (Song et al., 2006; Sugimura et al., 2002) and solution(Chen et al., 2014; Igor Luzinov, 2000) are commonly used. Recently, many articles have been published on the fabrication of superhydrophobic surfaces with SAM technology (Cho et al., 2007; Pan, Shen, Shang, & Xing, 2012; Siddaramanna, Saleema, & Sarkar, 2014; Song et al., 2006). Brassard, Sarkar, and Perron (2011) successfully obtained a superhydrophobic film by applying fluoroalkylsilane via self-assembly on monodispersive silica. SAMs are also reported as good candidates for anti-corrosion and adhesion promotion (Chen et al., 2014; Saleema, Sarkar, Paynter, Gallant, & Eskandarian, 2012). However, papers on the characterization of SAM properties are rarely seen. The most commonly used substrate for SAM is silicon and the method implemented is scanning probe microscopy (SPM) such as atomic force microscope (AFM) (Igor Luzinov, 2000; Moores, 2011; Zhang, 2003, 2005). Igor Luzinov (2000) analyzed the epoxysilane SAMs’ surface morphology and microstructure properties using scanning probe microscopy (SPM) and ellipsometry on single-crystal silicon wafers. SAMs have been used to improve the adhesion bonding of aluminum or plastics but no characteristic data have been presented yet (Saleema et al., 2012; Telegdi, 2007; Wang, Xu, Luo, Wang, & Wang, 2009). Recently, Reis et al.(Reis et al., 2006) have studied SAM of alkane diphosphonate (Gardobond X4661) on Al 5052 alloy samples by EIS in a naturally aerated sodium sulfate solution."

Jan 1, 2016

By K. Negishi, H. Izui, Y. Komiya

"Aluminum has the disadvantage of low strength. In order to obtain the high strength composites, crystals were refined in the composites. Grain refinement was approached at two process points, generating new grains and grain growth. It is important for refinement how to control the grain growth. Spark plasma sintering (SPS) technique and TiB2powder addition prevent grain growth. To investigate effects of strain and additives to the alloy, aluminum powder was sintered at 70 MPa and 80 MPa, changing the content of TiB2additive powder by SPS method. As the results, the crystal grain size was finer in the composite sintered at higher sintering pressure and with larger amount of additive, though over 1.0mass% TiB2addition dissuades grain refining. These grain refinements improve hardness and tensile strength of sintered aluminum alloys.INTRODUCTIONAluminum matrix composites have low density, high specific strength, and low cost. Their applications are growing continuously in the field of automotive and aerospace industries. Recent studies to improve their good mechanical and tribological properties use different ceramic materials such as Al2O3(Das, Munroe, & Bandyopadhyay, 1996; Ashwatha & Anthony Xaviorb, 2014),SiC(Hassani, Bagherpour, & Qods, 2014), B4C(Ehsan, Masoud, Touradj, Amir Hossein, & Ali, 2015),TiC(Ehsan, Ali, Masoud, Kamyar, & Touradj, 2017), and TiB2(Fei & Zhong-Hua, 2013).On the other hand, grain refinement is also an important techniques for improving the properties of aluminum alloys. Finer grains improve the mechanical properties of the alloy. For cast and wrought alloys, addition of grain refiners in molten alloys accelerates generation of nucleus and suppresses grain growth. Al-Ti-B alloy is generally added as grain refiners in the molten aluminum alloys(Easton & Stjohn, 2001). Especially, TiB2has very high melting point, low density, and excellent hardness. Therefore, TiB2was selected as additions into aluminum alloys. Liquids reaction leads to high cost, oxidation, discoloration of molten alloy, and clustering of additive powder as compared with solid reaction such as sintering. However, sintering of aluminum alloy powder with ceramic powders is difficult for oxide layer surface. Recently, we take attention to spark plasma sintering (SPS) as advanced sintering process. SPS process can easily sinter a high quality specimen at a lower sintering temperature and in a shorter time than conventional sintering processes. By SPS process, we have sintered titanium powders that are as difficult to be sintered by any other processes as aluminum powders, and improved mechanical properties by adding hard ceramic powders TiC and TiB(Kamegawa, Izui, Komiya, Kobayashi, & Arimoto, 2015; Sampei, Izui, Komiya, Shigimura, & Suzuki, 2015). Furthermore, it is important to consider not only pure aluminum but alloys for solid-solution or precipitation strengthening. Actually, pure Al does not have enough strength compared with the alloys. Al-Cu alloy and Al-Mg alloy demonstrate adequate strength for industrial and commercial sectors. Al-Mg alloy retains good formability, and has high resistance to corrosion. It is therefore used for many applications. We must consider alloying processes. The most cost effective process is blended elemental technology where alloying elements are added to base powder as elemental or master alloy powder (Smugeresky & Dawson, 1981; Yasue, Radjai, Miwa, & Sakaguchi, 2003; Bolzoni, Esteban, Ruiz-Navas, & Gordo, 2012)."

Jan 1, 2018

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"Abstract - The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By Harold L. Gibson, Don H. Rousell, Ian R. Jonasson

"The Sudbury Structure consists of three major components: 1) the Sudbury Basin; 2) the Sudbury Igneous Complex which surrounds the basin as an elliptical collar; and 3) an outer zone of shatter-coned and intensely brecciated footwall rocks. Although the Sudbury Event which formed the structure may be unique, the area has, in fact, been shaped by a series of tectonic, magmatic and mineralization events which can be considered in terms of two Wilson cycles of continental extension and closure. The first cycle, from 2500 to 1700 Ma, included the following events: doming (uplift of Levack Gneiss Complex); NE-SW extension (Matachewan dikes); N-S to NW-SE rifting (faults, mafic intrusions, sedimentation, and Ni-Cu-PGE and U mineralization); NW-SE extension (Nipissing diabase, and Ni-Cu-PGE, Ag, Co mineralization); and NW-SE and NE-SW closure (Penokean Orogeny, 1900 to 1700 Ma) with superimposed meteorite impact (1850 Ma, Ni-Cu- PGE, Zn-Cu-Pb deposits). The second cycle, from 1700 to 1000 Ma, included: N-S extension (alkali metasomatism, Au); N-S extension (hornblende diabase dikes along the Murray fault set); NNESSW extension (olivine diabase dikes); NE-SW extension (Fecunis Lake fault set); and NW-SE closure (Grenvillian Orogeny).The rich and diverse Ni-Cu-PGE and subordinate Zn-Pb-Cu and Au mineralization of the Sudbury region is related to endogenic and impact-triggered crustal extension and magmatism. The Sudbury Structure apparently was the site of a triple junction or hot-spot. The Sudbury ores, although located within an impact structure, are analogous in terms of age and tectonic setting to Ni-Cu-PGE and Zn-Pb-Cu ores elsewhere in the world. Meteorite impact accentuated on-going ore forming processes and magmatism at Sudbury."

Jan 1, 1997

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By Georges Houlachi, Akram Alfantazi, Michael Mahon, Maysam Mohammadi

Corrosion resistance of the lead-based anodes directly influences the purity of the final product in the zinc electrowinning process. The anodic MnO2 layer that is electrodeposited on the anodes during this process can protect the anodes against corrosion. Sand-blasted anodes generate a uniform, adherent and shiny MnO2 layer, which gradually blisters and eventually sloughs off after several weeks. In this study, we attempted to develop a new method to stabilize the MnO2 protective layer on the anodes during the electrowinning process by providing suitable nucleation sites for electrodeposition of this layer. MnO2 particles (P80=40µm) were used as seed material for this purpose. Different techniques of galvanostatic and cyclic voltammetry polarizations, scanning electron microscopy (SEM) and atomic absorption spectroscopy (AAS) were employed to investigate the performances of the MnO2-seeded lead anodes. The experimental results showed that growth of the MnO2 layer is influenced by the MnO2 seed particles on the anode surface. The MnO2 layers electrodeposited on the MnO2-seeded lead anodes were uniform and strongly adherent to the substrate. This layer was more stable than those formed on the PbAg anode without MnO2 seeding. This could provide the anode with a higher level of corrosion protection. Moreover, formation of undesirable MnO2 mud in the electrolyte and the rate of manganese consumption were decreased when the MnO2-seeded lead anodes were polarized. These observations could be attributed to the different properties of the electrodeposited MnO2 layer on this anode in comparison with that formed on the PbAg anode.

Jan 1, 2016

By H. Bouzahzah

Sulfidic tailings, subjected to atmospheric water and oxygen action, can generate acid mine drainage (AMD); which is the most important environmental problem facing the mining industry. AMD generating potential can be assessed by the static tests which consist of a screening method where the neutralization potential (NP) and the acid-generating potential (AP) of a given rock sample are determined. The AP and NP are determined separately in the different static test existing procedures which can be divided into two distinct classes: chemical and the mineralogical methods. For some chemical method, the AP is calculated on the basis of total sulfide sulfur content in the sample which may overestimate its AP if significant quantities of non-sulfide sulfur species are present (e.g. organic S in coals, some sulfate as gypsum, barite, etc.). However, the mineralogical method evaluates the AP by the sum of the individual sulfides participation on acid generation based on their concentration within the sample and can be more accurate than the chemical method. For AP calculation, the Paktunc (1999a) mineralogical static test takes into consideration all sulfide minerals occurring in the sample. However, it does not take into account the rates of acidity production of these sulfides submitted to weathering conditions. So, the present study focusses on the modification of Paktunc AP calculation by considering the acidity production rates of these minerals. To reach this objective, five base-metal sulfides (pyrite as reference, chalcopyrite, sphalerite, arsenopyrite, galena), diluted within quartz (25?75 wt.%) simulating mill tailings were subjected to a kinetic test to evaluate their AP. The results show that all the studied sulfides minerals generate acidity at different rates, so the Paktunc?s equation for AP calculation has been adapted accordingly.

Aug 1, 2013

By A. Warczok

Chalcocite concentrate obtained by magnetic separation and flotation of Bessemer matte is processed in the Inca top blowing bottom stirring MK reactor into semi-blister copper. The semi-blister is then converted into blister copper in the multi-purpose vessels (MPV) by oxidation of iron, nickel and sulphur. High melting point NiO and Fe30 4 are formed inside the MPV s, which together with Cu20 and smaller amount of fayalite are the major constituents of the solid mush. The accumulation of solid mush and buildup requires periodic MPV cleaning by adding reductant and copper-nickel matte, a unique process called "washout". Various reductants and their combinations, such as pig-iron, 15%Si Ferro-silicon and 50%Si Ferro-silicon, have been used for the reduction of solid mush and buildup. The possibilities of using calcium carbide as a reductant and slagging flux were examined experimentally at the crucible scale. The rate of reduction of MPV buildup was determined by continuous measurement of CO and C02 contents in the offgas and the flowrate of argon carrier gas. The rate of the buildup reduction with calcium carbide was approximately five times faster than the rate of reduction with coke. Additionally, the formation of CaO results in the melting of reduced buildup and formation of a slag at 1300°C and higher temperatures. It was found that simultaneous silica addition enhanced the melting and slag formation. The results showed the strong dependence of the reduction rate on temperature. Activation energy is approximately 225 kJ/mol. Expected benefits of using calcium carbide are related to cost saving on reductant, significant acceleration of solid mush reduction, and reduced amount iron input from reductant.

Jan 1, 2007

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016