Search Documents

By P. A. Bahri, D. G. Dixon, T. M. Woodward

A comprehensive mathematical model of the Sherritt-Gordon ammoniacal pressure leaching process at K winana Nickel Refinery has been constructed. The process is comprised of six autoclaves functioning as a three-stage leach circuit, operating over the temperature and pressure ranges of 85-95°C and 750-1000 kPa, respectively. The process chemistry forms a complex series-parallel reaction network, characterised by: (1) the gas-liquid mass transfer and reduction of oxygen, (2) the oxidation of eight distinct minerals, (3) the oxidation of sulphur, and successive reactions involving various intermediately oxidised sulphur species, and (4) the oxidation of Fe(II) to Fe(III), and subsequent precipitation as a hydrated ferric oxide. Material balances were developed for species in all three phases, and an energy balance to account for all reactions and phase conversions. The multiple convolution integral (MCI) statistical reactor model was employed for the scale-up of particle kinetics. The model has been validated against plant data, and simulation results are in agreement with plant performance.

Jan 1, 2005

By G. F. Liu, S. Owada

Platinum Group Metals (PGMs), Pt, Pd, Rh, have been widely used as a three-way catalyst to clean discharged gas from automobiles and therefore a considerable amount of the spent catalysts is generated annually. This paper proposes a novel concentration technology of PGMs by utilizing the double-deck structure of PGM bearing alumina-ceria and cordierite phases. The applied technologies are a combination of heating-quenching, selective grinding and screening for separating alumina-ceria phase from cordierite. Temperature change as a function of quenching time and the thermal stresses applied to both phases were simulated and calculated by FEM, and it was clarified the mechanism of micro-cracks generation at the phase boundary and micro-cracks in alumina-ceria phase, which indicated that separation of alumina-ceria phase from cordierite and selective breakage of alumina-ceria phase could be achieved in the subsequent selective grinding with an attritor. This process could concentrate 46 wt% of alumina-ceria phase into fine fractions with 86 % recovery efficiency. The remaining alumina-ceria phase can be further recovered by applying flotation and so on.

Jan 1, 2015

The introduction consists of back-ground information, of an historical and statistical nature, relating to the Thompson mine. The geological presentation is based on illustrations that are intended to provide a progressively closer look at the ore occurrence. The illustrations consist of an index map, a geological map of a 15-by 85-mile area including the Thompson mine, a series of four maps dealing with the geophysics and geology of a 6-by 4\f.j-mile area at Thompson, a mine level plan and corresponding section, two sto11e 11lans and corresponding sections, and photo-graphs and photomicrogra11hs of the various one types. T HE Thompson mine is located about 400 miles due north of Winnipeg. The ore deposit was dis-covered in February, 1956. Five years later on March 25, 1961, the Thompson production facilities were officially dedicated with the shearing of the first nickel produced at the Thompson refinery. Full production, at an annual rate of more than 75,000,000 lbs. of refined nickel, was attained later in the year.

Jan 1, 1963

By Edouard Asselin, Tasawar Javed

The precipitation of hematite from ferric sulphate - cupric sulphate - lithium chloride acidic solutions was studied in a batch reactor. The effect of several variables on the extent of hematite precipitation as well as on its crystallinity and purity was investigated. The variables studied include: initial ferric concentration (1.5 - 30 g/L), retention time (0 - 12 h), initial sulphuric acid concentration (0 - 30 g/L), temperature (150 - 220 °C) and chloride concentration (0 - 25 g/L). The results show that hematite is preferentially precipitated at lower initial iron concentrations. Longer retention times increased the fraction of hematite in the precipitates but did not affect its crystallinity to a significant extent. On the other hand, higher temperatures increased the purity and crystallinity of the hematite. At lower acid concentrations hematite and goethite were precipitated. However, only hematite was precipitated when the initial acid concentration was > 12.5 g/L. Better crystalline hematite was formed at lower acidities. Increasing chloride concentration increased the amount of hematite and decreased the amount of iron sulphate hydroxide phases, but did not affect the crystallinity of the hematite.

Jan 1, 2015

By S. Oppenheimer, P. Au, R. M. Kearsey, J. Tsang, E. McDevitt

A new superalloy, ATI 718Plus® Alloy (718Plus), has been developed to have a 55oC higher temperature capability over the traditionally used Alloy 718, while maintaining favourable processing characteristics and intrinsic raw material costs. The fatigue and dwell-fatigue behaviour of four microstructural variations of 718Plus are evaluated and compared to Waspaloy: 1) standard heat treated condition (HT1), 2) standard heat treated condition with thermal exposure at 732ºC (1350ºF) for 1000 hours (HT2), 3) fine grain condition with a modified d phase (HT3), and 4) fine grain overaged through modified heat treatment (HT4). The results show that the steady-state fatigue crack growth rates of each microstructural variation and both alloys are identical, with all of the 718Plus variations showing a clear advantage over Waspaloy in the fatigue crack threshold regime. Dwell-fatigue results show that Waspaloy has better resistance to crack propagation under dwell conditions; however, optimization of the precipitate phase shows vast improvement in the dwell-fatigue resistance of 718Plus.

Jan 1, 2010

By G. Hamel

The LCL&L process (Low Caustic Leaching & Liming) is a patented hydrometallurgical route developed by Rio Tinto Alcan (RTA) to economically process spent pot lining (SPL) generated by aluminum cells. The three resulting end-products (carbonaceous, fluorinated and caustic liquor) are inert and have valorization possibilities. An industrial size pilot plant located in Saguenay (Quebec) was inaugurated in mid-2008 to demonstrate and optimize the technology. This paper describes characteristics of the LCL&L process and the experience acquired by RTA since the plant's start-up, including ramp-up capacity and technology challenges that were overcome. Possible end-products valorization methods are also presented. The carbonaceous end-product can be separated into carbon and brick rich fractions and used as either alternative fuel, reducing agents, or as raw material for third party processes. The development of a conversion process for the fluorinated end-product would allow its reuse as a substitute to fluorspar mineral for aluminum fluoride production. Finally concentrated caustic liquor is already valorized at the nearby RTA Vaudreuil alumina refinery.

Jan 1, 2011

By M. Fafard, D. Picard, J. -F. Bilodeau, G. Soucy

To simulate adequately the behaviour of a Hall-Heroult electrolysis cell, a finite element model must take into account the properties of each material. However, it has some lacking knowledge on the mechanical behaviour of materials, like the long-term visco-elastic (creep/relaxation) behaviour of cathode. A three-dimensional model is then proposed in this paper and will be ready to be implemented in the finite element code FESh++. The model was developed using the three-dimensional model based on thermodynamic of irreversible processes where the choice of the internal variables is based on a phenomenological approach. All parameters of the model are represented by constant constitutive tensors and the temperature and chemical dependencies are taking into account through scalar functions multiplying the constant constitutive tensor. The goal of the first part of this project was to determine the parameters of the threedimensional visco-elastic model at the reference state (virgin material at ambient temperature) of three different cathode materials. This paper presents the theoretical model and the results of creep tests at ambient temperature for the semi-graphitic carbon cathode.

Jan 1, 2006

By M. Lghoul

Acid mine drainage (AMD) remains one of the major environmental problems for the mining industry particularly for many abandoned mine sites. The production of AMD as is commonly known can significantly affect the surrounding groundwater and surface water of the mine site. With the objective to investigate the impact of the AMD produced at the abandoned Kettara mine site (Morocco), groundwater sampling campaign was performed at this site. The sampled waters were analyzed to determine the hydrogeochemical composition, and then results were analyzed using different studied methods such as multivariate statistical analysis and geochemical modeling techniques. Investigation results show that the hydrochemistry of sampled waters is characterized by the relatively significant enrichment of Ca2+, Mg2+ and SO4 2-. The typical mine waters belong to the (Ca2+ +Mg2+)-SO4 2-type. Seasonal variations in major ion concentrations were partly attributed to dissolution/ precipitation processes. The saturation index (SI) calculation of the representative dissolved minerals in waters show that groundwater samples are undersaturated with respect to most potential sulphated secondary minerals.

Aug 1, 2013

By R J. Tremblay, R. R. Hoffman

This paper deals with materials of construction and problems encountered and overcome in leaching and filtration of oxidized sulphuric acid slurry in the Port Radium mill after eight years of operation. The slurry is characterized by a high calcium sulphate content as well as a high chloride level under oxidized conditions, both of which affected initial design and subsequent changes. Leach agitation tanks are of wood with a mild steel superstructure and stainless steel agitator and moving parts below solution level. Electro-polished 316 stainless steel cooling coils are used for temperature control of the slurry. The string filters are of the Oliver type with wood decking. Extensive use is made of wood, Linatex lined mild steel and stainless steel for the slurry handling. A typical analysis of the slurry solution follows:(pH-1.30) ClOa Fe+++ Free Acid UaOs c1-so.--0.10 gms/litre 10.2 gms/litre 6. 7 gms/litre 3.5 gms/litre 2.0 gms/litre 155 gms/litre

Jan 1, 1961

By V. Fiedler, H. Lachmund, R. Bruckhaus

"After producing some 50 million tonnes of crude steel the two BOF vessels at Dillinger Hüitte steel plant had to be replaced in 2000/01 due to large deformations. The new vessel design was optimised after a number of theoretical evaluations.Refractory investigations were carried out as well as temperature measurements of the shell to provide a basis for selecting a suitable steel grade. This was found in a DH-GTS development - P420M HT - with high strength at elevated temperatures and excellent weldability and made it also possible to build the vessel without any cooling system.After putting the first vessel into operation the metallurgical results showed no remarkable improvement compared to the old vessel, and were therefore not satisfying. With the help of cold model investigations the arrangement of the tuyeres was modified to improve the flow conditions and the interactions between oxygen jet and the heterogeneous plume of the bottom stirring gas. Further optimisations were obtained by a variation of lance tips and a newly developed lime addition model."

Jan 1, 2004

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By G. S. Ospanova

The results of complex processing sulphide copper ore and advantages of recovery of copper by vat and heap leaching, sorption, cementation and electrolytic solutions processing and utilization of waste material after heap leaching of copper for production of building materials were investigated. The combined chemical solvents with the additives of oxidizing agents are developed at the KazNTU. The solvents are inorganic or organic chemical reagents, which form complexes of Cu, Au, Ag, Pt, Ni, Sr, Co etc. Recovery of non-ferrous metals from solutions and purification of industrial waste waters is carried out on the base of using new synthetic and natural sorbents (from local raw materials) which are able to bind ions in both cationic and anionic forms depending on type of ligands and external conditions. Optimum parameters of copper sorption were determined. The developed wasteless technologies of copper extraction from sulphide ores with usage of new non-toxic solvents and accessible sorbents with full recycling of water are tested in pilot scale heap leaching, and are recommended as the ecological, economical and practical alternative to traditional methods.

Jan 1, 2007

By W. Kunda, J P. Warner

SHERRITT GORDON Mines Limited annually produce 300,-000 pounds of pure cobalt by processing a nickel-cobalt-copper-iron sulphide ore which is mined at Lynn Lake, Manitoba. The ore (containing 0.04 per cent Co) is •concentrated to give a concentrate containing l 1-12 per cent nickel, about 2.0 per cent .copper, and 0.25-0.35 per cent cobalt, which is treated at the Refinery in Fort Saskatchewan, Alberta. The concentrate is leached in an ammoniacal solution of ammonium sulphate using compressed air as the oxidant. After filtration the leach solution contains, besides nickel and cobalt, copper ammines, sulpharnates and salts of various thionic acids. The copper is removed by precipitation as sulphide and the sulphur compounds converted to ammonium sulphate by a combined oxidation and hydrolysis treatment. The purified solution •Containing about 45 gpl of nickel and 1 gpl of cobalt is treated with gaseous hydrogen under pressure at 350°F to precipitate metallic nickel powder, the precipitation 'being terminated when the nickel content of the solution is about 0.8-1 gpl. Only about

Jan 1, 1962

By V. Polotski

This paper describes a platform for autonomous operations in open pit mining environments. A typical operation consists of: (1) Initial locomotion toward a remote worksite; (2) Pattern navigation within the worksite; (3) Worksite manipulations and (4) Return locomotion to the start location. The platform includes precise localization module based upon the fusion of odometry, inertial and GPS measurements. The guidance module starts from a set of way points specified on a GPSreferenced map and plans and executes the mission. A typical mission includes specified manipulative tasks along the navigation path. During motion execution the on-board system continuously verifies that the path is free of obstacles and that the hardware is not overloaded. Momentary losses of external positioning measurements does not adversely affect the performance, owing to the redundancy in position and heading estimation. A rehearsal phase follows planning and allows the supervisor to examine the kinematic behavior of the platform during motion, thus reducing the need for continuous monitoring during execution and providing protection against potential losses of communication.

May 1, 2003

By Madaah Hosseini H. R., P. Abachi, S. Miraghaei

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled powders are much higher than those of corresponding Fe-Si bulk alloys with a minimum at 13.5 at.% Si. The values of coercive force decreased after annealing but it seams that the residual strain developed during milling is not the major contributing factor to the higher values of coercive force in the mechanically alloyed powders and nanocrystals behave as single-domain particles without exchange interaction between them.

Jan 1, 2006

"Here, we statistically proved that giant earthquakes occur at lunar phases specific to each subduction zone. Enough attention during the lunar period, especially when seismicity is occurring, will significantly reduce damage from giant earthquakes. Two case studies in which giant earthquakes occurred after seismicity in dangerous lunar phases were discussed, and the mechanisms underlying why giant earthquakes occur around neap tide at some subduction zones were explained by prohibition of giant earthquake occurrences due to high strain rates at spring tides at N–S subduction zones. The prohibition was statistically proven for uniaxial creep tests on Inada granite with slight stress disturbances. INTRODUCTIONIn previous studies, we showed that from 1900 to present, giant earthquakes (MW ??8) have occurred at lunar phases specific to each subduction zone (Fujii & Ozaki, 2012; Ozaki & Fujii, 2012). Although we later proposed a possible reason for these occurrences, the study lacked statistical analyses (Fujii et al., 2013). Therefore, this paper shows the results of such statistical testing and presents case studies for the Tohoku 2011 and Chile 2014 events, thereby providing updated data on giant earthquakes through July 2014."

Jan 1, 2015

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By N. W. D. Davis

"As I have recently carried out some further research on the Navan lead-zinc deposit data while working in Michel David's research team, I should like to add a few comments on the paper- ""Universal Kriging for Ore-Reserve Estimation- Conceptual Background and Application to the Navan Deposit"", by M. Dagbert and M. David (CIM Bulletin, pp. 80-92, February 1976). The first comment is that since this research has been carried out, important new theoretical advances have been made which make for an easier application of geostatistics to the non-stationary case (see Matheron0l). This is the theory of intrinsic random functions of order k. With the aid of this theory, it has been possible to write computer programs which can carry out automatically universal kriging, although so far such applications have been largely confined to automatic contouring and not to mining problems. However, if approached with care there is no reason why these methods should not be applied to mining problems and, in this case, an automatic study has been done on this data."

Jan 1, 1976

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945