Search Documents

By Xiu-Xiang Tao

This study investigated bio-liquefaction of lignite and its model compounds of thymol, bezioc acid and quinoline by a fungus, Hypocrea lixii AH. It analyzed, during bio-liquefaction, enzyme activity of oxidase, LiP, Lac, MnP and polyphenol oxidase, and degradation products by UV-Vis, FTIR, 13C NMR and GC-MS. The results showed that the bio-liquefaction percentage (by mass) of lignite was up to 44.86 %. The bio-liquefaction products of lignite were mainly aniline, amide, ether, carboxylic acid ketone and ester. The aromatic ring number was 1-3 with an aromatic carbon ratio of 0.328, which indicated rings opening, bonds breaking and oxidation reaction. By considering with the enzyme activity analysis results, it showed that LiP and Lac catalyzed reactions to open aromatic cycles and to break bonds; esterase to break ester bond; and peroxidase in oxidation reaction.

Aug 1, 2013

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By G. Deschenes

"This literature survey discusses the recovery of gold from thiourea solutions. An overview of techniques used and general comments on the basic cyanidation methods are presented. The chemistry and mechanisms of cementation, activated carbon, resins, electrowinning, solvent extraction and pressure reduction are examined. Conclusions and recommendations give orientation for future research and development activities in this field.RésuméCette revue littéraire traite de la récupération de I ‘or des solutions de thiourée. Elle fait un survol de I ‘ensemble des techniques utilisées tout en introduisant des commentaires généraux sur la méthode classique qu'est la cyanuration. La cémentation, Ie charbon active, les résines, l'électroextraction, I ‘extraction par solvant et la réduction sous pression sont les méthodes analysées tout en considérant leur caractère chimique respectif ainsi que les mécanismes qui y sont rattaches. Des conclusions sont tirées et différentes recommandations sont suggérées pour orienter la recherche dans ce domaine."

Jan 1, 1986

By J. Schmidt

Cold drawing of copper wire rod is usually combined with an in-line annealing process to adjust the ductile microstructure of the wire again. One important key factor for successful annealing is the quality of the copper itself. Rod producers can check the recrystallization behaviour of the rod by different methods: chemical analysis, Spiral Elongation Test (SEN) as well as the Rapid Elongation Test (AR) are some examples of common testing methods. The comparison of the results of these methods does not always show sufficient correlations. The paper introduces firstly the SEN and AR-Tests and their different approaches to the mentioned task. The second step is to compare some results of the SEN-Test with the results of the AR-Test and identify causes of deviations. Thirdly, the effect of pre-annealing is discussed, which is especially common for wire rod with diameters of more than 8 mm.

Jan 1, 2007

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By M. Huang

Electrodeless conductivity was employed to investigate the feasibility of continuous on-line monitoring of the free acidity of sulphate and/or chloride solutions of Cu and other base metals from various hydrometallurgical processes. These solutions were measured with both commercial and experimental electrodeless conductivity sensors from 15 to 250°C. It was confirmed that hydrogen ion has the greatest impact on conductivity by carrying the bulk of the current because it is the most mobile ion. In combination with a solution speciation analysis the conductivity sensor can be calibrated to account for the contribution of Cu electrolytes as well other dissolved salts allowing fast and accurate on-line measurement of free acid. The sensor was tested at both lab and pilot scale with very good performance. The average difference between the measured and the titrated acid concentration was less than 5%, which is excellent for industrial applications.

Jan 1, 2007

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By M. Isac, R. I. L. Guthrie, S. Ge

The Al-Mg-Sc-Zr alloys have shown exceptional potential as structural materials for transportation applications. These alloys have proved to be good candidates to be processed as thin strips via the Horizontal Single Belt Casting (HSBC) process. The HSBC process is a near-net-shape casting technology, which involves casting molten metal directly into thin strips, close to the final product thickness, at high cooling rates. It offers an efficient, economical and environmentally-friendly approach to the production of metal strips. Fluid mechanics and associated heat transfer are important aspects of any casting process, and the novel HSBC process is no exception. Three dimensional Computational Fluid Dynamics (CFD) simulations using ANSYS FLUENT 14.5 were performed, in order to assess the importance and effects of the various operational conditions of the HSBC process. This enabled process parameter optimization. Numerical predictions were validated against experimental casting results.

Jan 1, 2014

By B. Lafrance, C. J. Beaumont-Smith, L. R. Jones

"Abstract - The Burnt Timber gold deposit is located in the Paleoproterozoic Lynn Lake greenstone belt of the Trans-Hudson Orogen, Manitoba. The deposit occurs along the Johnson shear zone, and is hosted by enriched and depleted tholeiitic volcanic arc basalts cut by feldspar porphyry dikes. The Johnson shear zone is a regional, belt-parallel structure characterized by the intensification of the regional S2 foliation. At the Burnt Timber deposit, S2 is folded by centimeter- to meter-scale, Z-shaped, F3 chevron folds that have an axial planar S3 crenulation cleavage. Within the 20 to 30 m-wide core zone of the shear zone, S2 and F3 are transposed parallel to S3 and the volcanic rocks are strongly sheared parallel to S3. The presence of a steeply plunging stretching lineation, together with dextral shear sense indicators along both S2 and S3 on horizontal surfaces, suggest that the Johnson shear zone is a dextral transpression zone. Gold was introduced in pyritic, biotitic, and carbonatized mafic volcanic rocks along the core of the shear zone. Mylonitic mafic volcanic rocks contain localized high-grade zones (=10 g/t Au) that differ from wider carbonatized, low-grade zones (<3 g/t Au) by the presence of deformed gold-bearing quartz-pyrite veins. High-grade zones are also associated with swarms of quartz-pyrite veins that cut across sericitized and carbonatized feldspar porphyry dikes, which acted as brittle, competent bodies during shearing. Gold deposition in the high-grade zones was controlled by the channeling of hydrothermal fluid along the core of the shear zone during shearing of the volcanic rocks, and brittle fracturing of the porphyry dikes. Sommaire - Le gîte aurifère de Burnt Timber est situé dans la ceinture de roches vertes Paléoprotérozoïque de Lynn Lake dans l’orogène Trans-Hudsonien, au Manitoba. Ce gîte est situé le long de la zone de cisaillement de Johnson et est encaissé dans des basaltes tholéiitiques d’arc enrichis et appauvris recoupés par des dykes porphyriques. La zone de cisaillement de Johnson est une structure régionale parallèle à la ceinture de Lynn Lake caractérisée par une intensité accrue de la foliation régionale S2. Au gîte de Burnt Timber, S2 est affectée par un plissement F3 en chevrons en Z d’échelle centimétrique à métrique associé à un clivage de crénulation de plan axial S3. Dans la zone centrale de 20 à 30 m de largeur au sein de la zone de cisaillement, S2 et F3 sont transposés parallèlement à S3 et les roches volcaniques sont fortement cisaillées le long de S3. La présence conjointe d’une linéation d’étirement à forte plongée et d’indicateurs cinématiques dextres sur les surfaces horizontales S2 et S3 suggère que la zone de cisaillement de Johnson est une zone transpressive dextre. L’or a été mis en place dans des volcanites mafiques altérées en pyrite, en biotite, et en carbonate au coeur de la zone de cisaillement. Les roches volcaniques mylonitiques présentent des zones aurifères locales à haute teneur (=10 g/t Au) qui diffèrent des zones à basse teneur (<3 g/t Au) par la présence de veines de quartz et de pyrite aurifère. Des zones à haute teneur associées à des essaims de veinules de quartz et de pyrite sont aussi notées dans des dykes porphyriques à plagioclase altérés en séricite et en carbonates; ces dykes se sont comportés comme des corps compétents durant le cisaillement. La déposition de l’or dans le zones à haute teneur a été contrôlée par la circulation du fluide hydrothermal au coeur de la zone de cisaillement durant la déformation des roches volcaniques et la fracturation des dykes porphyriques."

Jan 1, 2006

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen&apos;s Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By S. J. Prout, J. M. Lang, D. Lascelles, K. Sarinas

"There is a growing demand for ore characterization methods to support metallurgical development programs from a true geometallurgical perspective. Today, there are multiple automated mineral analysis systems on the market, many of which are based on conventional mineral liberation data. However, liberation data can be limited when assessing the floatability of a mineral to predict its recovery as it doesn’t consider the surface area available for collector absorption and bubble attachment; whereas mineral exposure measurements can. Using the First-Order Rate equation to predict the recovery versus time of variously exposed particles, a model has been developed to predict the recovery of copper sulphides at a particular grind size. This model provides the opportunity for the prediction of copper recovery and grade from multiple, small-scale samples. These predicted values can be imported into resource modeling software, and guide the domaining of geometallurgical units within the ore body. Data has been analyzed from various global copper porphyry systems and compared with actual flotation testwork.IntroductionAs part of the development of a mining project, resource estimation primarily focuses on the definition of the quantity and grade of the ore in the deposit; as the project evolves from preliminary economic assessment through to feasibility, the geological model is usually further populated with hardness and recovery data.The CIM Definition Standards (2011) identifies measured mineral resource as the part of a mineral resource for which quantity, grade or quality, densities, shape, and physical characteristics are estimated with confidence sufficient to allow the application of “modifying factors” to support detailed mine planning and final evaluation of the economic viability of the deposit as an asset. The modifying factors include, but are not restricted to, mining, processing, metallurgical, infrastructure, economic, marketing, legal, environmental, social and governmental factors.With market fluctuations, many investors in the mining industry have become more and more risk averse which has increased the demand for more reliable data to support these modifying factors. This has led to the widespread use of geometallurgy and statistical analysis to better inform the resource estimation. Geometallurgy is used to characterize ore variability and is especially useful for highly variable or strongly zoned deposits, several close deposits that will be milled together, projects requiring complex or new metallurgical approaches, brownfields or sight-of-mine exploration, expansion projects that exploit new, deeper or adjacent reserves, and projects with significant legacy drill core that are being re-evaluated due to new economic circumstances."

Jan 1, 2018

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By M. S. Millman

Close monitoring of performance at each process stage, from raw material through to finished product, is vital for operational consistency and the production of high quality steel. However, many of the integrated iron and steelmaking process route stages operate under such severe conditions of temperature, dust, water, thermal radiation, vibration, pressure, vacuum, extreme dynamic events, high material flows, corrosion, erosion, electrical-noise, electromagnetic-noise, or audio-noise that, in general, it is a very difficult challenge to obtain useful information for control. Thus, state-of-the-art non-contact and remote sensors are applied to help monitor and control specific process operations. Often, these sensor systems have been developed especially for the steel industry and they are based on four principal technologies: Laser, Microwave, Electro-Magnetics and Thermal Imaging with supporting technologies such as: X-ray Fluorescence, Audiometry, Digital Image Processing, Radio Telemetry, GPS and many others. These advanced sensor technologies are reviewed with respect to their application at various stages along the integrated process route.

Jan 1, 2004

By H. C. W. Bosman

"Over the past five years, contributions from geologists and mining engineers were instrumental in the successful development of MEPS. It is a system of FORTRAN programs specifically designed to be used by mining personnel to solve geological and mining problems. MEPS is a flexible keyword-driven system. Extensive error editing procedures significantly reduce the time required to proceed from problem recognition to solution. Possibly the most attractive feature of MEPS is that computer solutions may be guided or selectively modified to obtain desired solutions. Some highlights of MEPS are:1. Vocabulary that is familiar to mining people.2. Geological data storage and retrieval.3. Statistical analysis and variograms.4. Contour maps of assays and geological horizons.5. Trend surface analysis with residual evaluation.6. Ore reserve calculations.7. Open-pit mine design.8. Marginal profitability calculations on pit walls.9. Production scheduling.10. Vertical cross-section plots indicating pit outlines, ore grade contours and selected geological horizons."

Jan 1, 1973

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By Hyumng Sup Choi

The role of the interfacial electrical &apos;Condition on the adsorption of col-lectors on mineral surfaces has been studied by electrophoretic mobility and adsorption measurements made on zircon. From the investigation of the electrokinetic properties of zircon, H+ and OH-are seen to act as potential determining ions, thus controlling the electrical nature of this mineral. The isoelectric point of zircon occurs at a pH of approximately 5.0, and it is evident, therefore, that the zircon surface would be positively charged below a pH of 5.0 and negatively charged above this pH. The adsorption of collectors therefore de-pends strongly on the pH of the solution; anionic collectors are adsorbed on positively charged surfaces and cationic collectors on negatively charged surfaces. This, in turn, de-fines the effective flotation condition, with respective collectors, for this mineral. The above results have been correlated with the flotation behaviour obtained by the simplified flotation test using a modified Hallimond tube.

Jan 1, 1963

By A. Ghasemi

An alumina-silica coating was deposited on a nickel substrate by sol-gel process, and the structures and composition were evaluated, The sols were made from aluminium and silicon alkoxide, and an acid catalyst including HCl, To produce adherent silica coatings on nickel, various additives such as surfactant, viscose additive and drying control chemical additives were introduced to the system, and appropriate drying and firing cycles were applied after dipping in solution. The hot corrosion and oxidation resistance of the coating at different temperatures were investigated, The structure and uniformity of the coatings were examined by scanning electron microscopy (SEM), The results indicate that a uniform coating of alumina silica can be produced on a nickel substrate by optimizing the composition and process variables of the sol. Coatings can protect substrates from oxidation and hot corrosion at different temperature up to 1000°C, but is not very effective for hot-corrosion resistance at 1000°C.

Jan 1, 2005

By L. Fernandes

A two level factorial study was undertaken to investigate the relative impacts of factors affecting the kinetics of polytetrafluoroethylene, PTFE, assisted pressure oxidation of chalcopyrite. A copper flotation concentrate, principally composed of chalcopyrite, was leached in 850 mL of leach solution under conditions similar to those of the CESL process. The factors manipulated were: the amount of 1/8" PTFE beads added (100 g or 650 g), oxygen pressure (690 kPa or 1030 kPa), and concentrate addition (10 grams or 65 grams). Copper extraction data, which indicated complete leaching under certain conditions, were fit using a shrinking core model from which rate constants were estimated and further used to generate a statistical model containing only the factors of significance and their interactions. Results indicated a strong positive effect of PTFE addition and a strong negative effect of increasing pulp density. A weak negative interaction between increasing PTFE addition and pulp density was attributed to PTFE/concentrate agglomeration.

Jan 1, 2014

By G Zahary

THE most acceptable approacl1 to analyzing rock behaviour, at the present time, is based on the application of principles of mechanics and strength of materials. Analyses have been made in which the criterion of failure is based on maximum stress (1) and on Mohr&apos;s rupture theory (2). If such analyses are to be carried out, the mechanical properties of the rock must be known within acceptable limits. Although an adequate correlation of laboratory test results with field conditions has not been established, test results have been published (3) on the basis of their comparative value. That is, test results may be useful for comparing the behaviour of different rocks under similar loading conditions or of a particular rock under different loading conditions. This study aims at establishing some of the mechanical properties of an andesite rock by testing specimens cut _from diamond drill core. Drill core (EX) was provided from run-of-mine drilling by New Dickenson Mines Ltd. and Campbell Red Lake Mines Ltd.

Jan 1, 1963