Search Documents

By Dale L. Pitt

Introduction In opening up a new country, one of the most vital problems is that of transportation Without roads, railways, or water routes, development is very slow because these are the arteries through which the life-blood of the country flows. British Columbia is unusually fortunate in having along its western coast, for some 600 miles, a stretch of inside water unequalled, for comfortable and safe navigation, by any other similar stretch of ocean in the world. This solves in a general way the major north and south transportation problem for the coast section, and offers comparatively cheap rates for the shipping of all commodities. The principal cities and centres of distribution will naturally grow up on the coast. These cities, however, must have methods of communication with the hinterland, and it is the necessity of supplying these, as feeders to the principal ports, which presents problems of considerable magnitude.

Jan 1, 1930

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By J. Paraszczak

ABSTRACT Diesel-powered loaders are a pillar of modern underground metal mining. As these mines are getting deeper and hotter and the emission regulations stricter, ventilation costs are soaring, affecting production cost. Also, the cost of diesel fuel is expected to rise. These may make the use of diesel engines more problematic. Electric load-haul-dump machines (LHDs) are an interesting alternative. This paper compares features and performance of diesel and electric, cable-powered LHDs. It overviews equipment offerings, and compares, analyzes and discusses technical parameters, operational problems and cost issues. The paper gives some conclusions about electric LHD applicability and performance, indicates possible applications, and suggests further research work.

Jan 1, 2013

By Charles Camsell

If it were necessary to preface a discussion of the mineral position of the Empire by justifying one's interest in that subject, there are two points that at once suggest themselves by way of vindication. Tremendous Growth of MINERAL Consumption The first of these points has to do with the general question of the world's mineral consumption. Most thinking persons appreciate in a more or less vague way the vital rôle that has been, and is being, played by mineral products in building up the material side of our modern civilization. But, apart from that casual and almost subconscious appreciation, very few have any precise knowledge of the extent to which the growth and the operation of our vast present-day industrial structure has been made possible by, and only by, a tremendous increase in the consumption of mineral products of all kinds. The increasing use of minerals confronts us today at almost every turn. It does not matter in what direction we look-at the expansion and the change in transportation facilities, in the air as well as on land and on sea; at the increasing mechanization, not only in factory and mill but even in our domestic life; or at the constantly widening use of machinery for all phases of farm production-everywhere we meet the same phenomena of rapidly growing uses of equipment produced mainly from minerals. Without resorting to any tiresome statistics, a few figures may suffice to indicate with what enormous strides the world's mineral consumption has been advancing. The figures for recent years may be open to objection on the plea that, ever since the outbreak of the world war, conditions have hardly been sufficiently normal to give us trustworthy data-we have been living under extremes either of depression or of abnormal stimulation. During the last decade before the war, however, from 1903 to 1913, the world was moving along in a quietly prosperous manner; and we have figures, or at least reasonably reliable estimates, as to the growth in mineral consumption during that decade.

Jan 1, 1932

By D. S. Case

"Following a brief explanation of the land arrangements under the Alaska Native Claims Settlement Act, this paper will examine both a mineral exploration agreement and a mining development agreement negotiated between two large mining companies and two different Alaska Native institutions. One of the institutions is a village corporation involved with an exploration agreement and the other is one of the Alaska Native regional corporations, which is party to a mining and development agreement with Cominco Alaska for the development of the Red Dog lead and zinc mine.Special attention will be given to the factors to be considered when dealing with small aboriginal owners with few resources in the context of an exploration agreement, including development issues which must be considered early in the process. The paper will also discuss the unique royalty and taxation structures developed for the Red Dog Mine Agreement as well as environmental issues. The paper will also consider the ways in which the cultural and differing economic interests of an aboriginal owner and a large mining company have been accommodated in the both the exploration and development agreements"

Jan 1, 1998

By Leroy C. Stewart

Owing mainly to the use of ethylene dibromide in the production of tetraethyl lead for gasoline treatment, there has been a tremendous increase during the past decade in the demand for bromine. In the United States, production, derived mainly as a by-product from the treatment of brines from salt wells, rose steadily from about two million pounds in 1924 to nine million pounds in 1931. In 1936, production amounted to between 20 and 21 million pounds. Much of the increase during the past four or five years has been due to the operation of the Ethyl-Dow Chemical Company's plant, which extracts bromine directly from sea water. The process employed by the Ethyl-Dow Company is somewhat similar to that in use on salt-well brines at their plant at Midland, Michigan, but whereas these brines contain around 1,300 parts per million bromine, sea water contains only 65 to 70 p.p.m.-about as much as the waste effluent in the brine process. By intensive research, however, a process was developed whereby a very considerable percentage of the bromine content of sea water could be recovered, and at a satisfactory operating cost. In its essentials, the process consists in liberating the bromine from the sea water by treat-ment with chlorine, blowing the bromine out of the water by a current of air, and finally absorbing it in a solution of soda-ash.

Jan 1, 1938

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

By T. Gonzales, S. Thakurdin

The conducting of risk reviews is an essential activity in ensuring safe operating conditions, both during project design phases and for existing facilities. The following paper presents a structured approach to the conducting of risk reviews for existing operations, including descriptions of supporting documentation and guidelines for on-site review activities. The conducting of regular site risk reviews and safety audits is crucial in ensuring the continued safe operation of existing facilities, particularly in the copper industry where numerous processes and unit operations can present catastrophic risks, both in terms of loss of life and financial liability. The structured approach presented aims to provide a logical and comprehensive analysis of risks to align safety-related facilities and procedures with current industry best practice and ensure consistency across multiple client operations. INTRODUCTION The production of copper, whether by pyrometallurgical or hydrometallurgical process routes, carries significant inherent safety risks. Production volumes are relatively large, often requiring complex processing routes, multiple production trains and a variety of supporting ancillary facilities. Furthermore, considering the relatively large size of ore reserves, copper production plants can have operational lives well beyond the typical design duration of 20 years. In this context, the conducting of regular risk reviews is essential in ensuring safe operating conditions and aligning facilities with current industry best practices. Risk reviews and safety audits can take various forms and have various areas of focus. The methodologies and approaches described below relate specifically to catastrophic risks, defined broadly as risks that carry the potential for multiple fatalities and significant financial losses. Focus is given to existing facilities and does not consider the risk-related activities such as hazard and operability (HAZOP) studies conducted during plant design. The structured approach presented aims to provide a guide for effective site- based audits and a logical analysis of risks identified. RISK CLASSIFICATION Table 1 provides a typical summary of the classification of risk types and the associated consequence categories and descriptions. It illustrates the descriptions of a catastrophic risk in terms of the broad categories of Health & Safety, Environment, Financial, Image & Reputation and Legal & Compliance. In terms of the Financial category, numeric costs ranges are often prescribed depending on the financial characteristics of the specific operation and the associated parent company.

Jan 1, 2019

By A. E. Boudreau

Abstract-It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydrothermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward- migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

By Ross Gallinger

In 1997 a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded (i) that Canadian industry and NRCan should fund a small secretariat in Ottawa to support technology transfer in Canada and (ii) that it was important for industry to continue the momentum of MEND on an international scale. The need for INAP (International Network for Acid Prevention) was strongly endorsed by company, university, consultant and government experts from Australia, Canada and the U.S. who were convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP's members to promote the dissemination of successful practices, the identification of knowledge gaps and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry based initiative to globally coordinate research and development in the management of sulfide mine waste. Significant improvements in the management of sulfidic mine materials through knowledge sharing, research and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP.

May 1, 2002

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

By Daniel Hodouin, Bruno Girard, Claude Bazin

"Mineral processing and smelting operations have the reputation of being complex processes. Process operators of these unit operations have acquired from experience and basic training a superficial understanding of the relationships between process output and manipulated variables. This understanding, which is a very valuable know-how for process control and optimization as well as for operator training, is however difficult to extract. This paper describes a time series based approach that can be used to extract this know-how, which can subsequently be used for operator training. The method is illustrated with an example taken from a smelting process.IntroductionThe emergence of Total Quality Management and Statistical Process Control philosophies in the North American industry (Brown, 1991 ), as well as the increasing popularity of the IS0- 900x standard accreditation, provide a strong incentive to review the training procedures for plant operators. The importance of employees training is acknowledged in two of the 14 points of Deming's road to quality (Deming, 1982) as well as by control engineering consultants (Hendricks et al., 1994). However guidelines for the operation of industrial processes are often transferred from an operator to another one with allowance for flexible interpretation of many operating rules. Such transfer is typical of complex industrial processes to which particulate processes of ore dressing and extractive metallurgy belong.Capturing the knowledge of experienced operators is often a difficult task. Cognition engineers are able to extract this knowledge and transfer it into rules that ultimately are implemented into expert systems. Cognition engineers are however not always available and plant supervisors may prefer to keep training as an internal liability. Another difficulty through interviewing of the process operator is its lack of willingness to transfer what he has learned by hard working to other people, whose ultimate goals are to develop computerized applications that may replace him in a near future, or reduce its importance in the production line.This paper shows that time series can be advantageously used to capture the average process understanding of plant operators and to help reviewing training procedures. The method s illustrated with data collected during normal operation of electric arc furnaces and it is shown how the approach has led to a fruitful discussion between process engineers and operators that ultimately provided savings of more that $200,000 per year per furnace. There are 9 furnaces in the studied foundry. Such savings are not the results of application of advanced control strategies nor of ""miracle press button software», but of an improve awareness by engineers and operators of the importance of properly defining the operating procedures to control a process."

Jan 1, 1996

By E. Gaucher, M. St-Amant

"Among the electromagnetic surveys performed by SOQUEM in the last three years, a certain number of the more instructive cases have been chosen to illustrate the theory of electromagnetism by field examples of: (a) The depth penetration of the TURAM as compared to the SLINGRAM (Ronka) method. (b) The limitations of the TURAM as compared to the SLINGRAM method when a conductor dips the wrong way, or when it is small in size. (c) The expression of a shallow-dipping conductor in a SLINGRAM survey. (d) The effect on the SLINGRAM survey of deep ditches or reef structures.(e) A comparison between the CRONE and the SLING-RAM method in the Abitibi clay belt, by means of field and model studies, indicating a usually better signal-to-noise ratio for the SLINGRAM method. From the above and from other experiments, different electromagnetic methods are now being used by SOQUEM, depending on field conditions."

Jan 1, 1970

By J. Güntner

A significant portion of Outotec's business relates to the application of fluidized bed for processing a wide range of industrial materials, including gold ore and gold concentrate. As part of the former Lurgi and Boliden organization, our division constructed the first industrial reactor for roasting sulphur-bearing materials in 1950, based on the principles of fluidized bed technology. This process, when combined with efficient heat recovery and off-gas treatment and its conversion to sulphuric acid, became the standard for processing sulphur-bearing ores. In the last 60 years we have delivered more than 265 plants and developed (in addition to the standard fluidized bed solution) variants of the fluidization technology, such as the circulating fluidized bed and the bubbling fluidized bed. This paper describes the different options of the fluidized bed technology for gold roasting reflecting on main process design criteria.

Jan 1, 2011

By S. Kariyawasam, R. McNealy

Pipelines are subject to multiple threats often requiring quantification of pipeline risk and engineering evaluation of in-line inspection and other data to effect discovery of conditions defined by the regulation. Public concern and pressure from regulatory bodies are accelerating the need for pipeline operators to formalize and intensify their approach to integrity management. Most operators need a phased approach to progressively adopt the most relevant and needed assessments. The organized and relevant assessment steps need to be introduced according to data available and maturity of the integrity management program. Each refinement to the quantification offers distinct advantages to the user. In this paper, the progressive integrity assessment solutions using quantitative methods are presented. Methodologies for engineering evaluation of integrity in-line inspection data for immediate and future integrity are summarized. Corrosion is used as an example, but the approach is applicable to any time-dependent defect based hazard. Strategies for pipeline integrity management are discussed.

Jan 1, 2005

By S. Belair, V. Weigel

As a growing mining company, ERAMET is looking for new positions on the strategic metals market. In this context, the Gabonese Maboumine pyrochlore deposit is currently being studied for the recovery of niobium, tantalum, rare earth elements (REE), and uranium. This ore shows mineralogical and chemical characteristics that make it challenging to process by already known practices, from both technical and economic points of view. In this context, ERAMET has developed since 2008 an innovative hydrometallurgical process which has been successfully operated at a pilot plant scale. While the upstream part of the process aims to dissolve the valuable elements in sulphuric acid, the downstream part of the process aims to recover them separately in a marketable form. The focus here will be on the recovery of the REE. The ore deposit contains approximately 1.4% of REE including 87% of light REE and 13% of medium-heavy REE. The challenge in this process lies in the fact that the major elements in the matrix are iron and aluminum. An innovative process has been developed in order to recover all of the REE in these unfavourable conditions, described in this paper.

Jan 1, 2014

By J. S. Brock

Magnetic, electromagnetic and gravimetric surveys have played an important role in the mineral exploration leading to the discovery of three major massive sulphide deposits in the Anvil-Vangorda area of the Yukon Territory. During 1964 and 1965 a saturation prospecting program, relying heavily on the integrated use of airborne and ground geophysical survey techniques, led to the discovery of the Faro deposit, which was subsequently proven to be a 63-millionton lead-zinc orebody. Locating the Faro deposit, the largest found to date in this overburden-covered region, involved an exploration sequence requiring the selection of a favourable geologic environment, aeromagnetic and electromagnetic surveys, property acquisition of anomalous areas and detailed ground geophysical surveys, followed by rotary drill testing, detailed gravimetric surveys and diamond core drilling.

Jan 1, 1973

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack 'of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930

By Frank Doxley

"FIRST OF ALL I should like to express to the members my sincere thanks for having had the privilege of serving them as President during the year now ending, to the Council for their guidance, and to the Secretary-Treasurer for his untiring efforts on both the Society's and my behalf during my year of office.During the .past five years the Canadian •Coal picture has changed considerably. In the West, production has been almost halved and many mines have been closed, due to the development and expansion of oil and natural gas industries, which, with some imported residual oil -on the Pacific coast -have provided competition which has been impossible to meet. The two major railway companies have embarked on an oil-burning and dieselization .programme and with this has .been lost one of the largest available markets for coal. Natural gas pipe-line installations still further threaten the remaining outlets for Western coal.In the East, retention of markets has also been a •problem, due to the intense competition provided by imported American •coal and the importation of residual oil.Because of cost it is impossible for central industrial Canada to be supplied with .coal from the Maritimes and markets are, therefore, restricted to fringe areas in Ontario and Quebec, and the Maritime Provinces.The dieselization programme of the Canadian National Rail ways has meant the loss of a large market for Nova Scotian coal and it is fair to assume that within a comparatively short time the market will be completely lost."

Jan 1, 1955

By Karl J. C. Harries

Mineral Agreements and Royalties

Jan 1, 2003