Search Documents

By G. Diaz

Técnicas Reunidas (TR) has been involved for over 30 years in the development of process technologies for the recovery of zinc from different primary and secondary feed materials, such as the ZINCEXTM process. Because of the complexity of the feed mineral resources, solvent extraction (SX) is an invaluable technique to concentrate and purify zinc solutions. When applied to a pregnant leach solution, solvent extraction can produce an extremely high quality zinc electrolyte, suitable for obtaining SHG zinc ingots, after electrowinning and melting and casting processes. However, the high affinity of most organic extractants for Fe(III) poses a serious problem, which may adversely affect the zinc extraction process. Different methods may be applied to deal with the negative effect caused by Fe(III). An acid regeneration step and electro-reduction stripping have been considered as the most viable techniques to remove the iron from the organic phase. This paper describes some findings of Técnicas Reunidas in the area of zinc solvent extraction, especially on removing Fe(III) from the organic phase.

Jan 1, 2006

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By L. Veleva, Garcia. A., G. Perez

Aluminum is a metal used for the transmission of electricity of high voltage, in the construction industry and other areas. In atmospheric conditions aluminum forms an oxide layer (Alz03'H20) as a result of its corrosion, entering the passive state. The oxide layer can be destroyed by the presence of ions (Cr, SOx-n) developing localized (non uniform) corrosion attack by pitting, difficult for evaluation. The concepts of fractals and self-similarity were used in this study for the characterization of the development of localized corrosion. Images obtained with a scanning electron microscope (SEM) of samples of electrolytic aluminum wire that have been exposed during one year in ruralurban and marine-coastal environments of the humid tropical climate of Mexico, have been processed. The development of pitting has been studied as a function of time, making a statistics of the frequency of appearance of pits versus the area occupied by them. The data show that the distribution of the pits follows a power law. Therefore, the concept of self-similarity can be applied for the study of the phenomenon of localized corrosion, describing their development with time.

Jan 1, 2006

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By Mark Sherman

One of the main functions of a process technology and engineering services provider is to select grinding equipment that will meet the client?s throughput rate target. Prudent risk mitigation strategies would suggest that throughput rate estimates be cross-checked using a variety of techniques. Whilst some comminution circuit designers have estimated specific energy requirements via the manipulation of the Bond specific power equation e.g. Barratt?s Grindpower and OMC?s FSAG approach, other designers have opined that the Bond Indices have no role to play in the calculation of SAG mill specific power. As a result, they have developed their own specific energy estimating methodologies, e.g. SMCC?s Drop Weight based power methodology, SPI, SAGDesign, etc. Each method has its supporters and its critics. The challenge facing the engineering provider is how to nominate an SAG mill based circuit throughput rate estimate when faced with significantly disparate specific energies calculated by the different methodologies. This challenge is exacerbated via the continuing evolution of contemporary circuit configurations such as two stage pebble crushing some of which incorporate HPGR technology as the second stage of pebble crushing. The methodology presented in this paper shows that the Bond Indices are an excellent tool for estimating the specific energy requirements for SAG mills in SAB, SABC and SSS circuits. The method accommodates primary crushed feeds, partial and or fully secondary crushed SAG mill feeds, and emulates the impact of pebble crushing on SAG specific energy. As a result, the new Bond Index based method has provided an additional tool for increasing Fluor?s confidence when predicting SAG mill based circuit throughput rates. Based on this outcome, the author proposes that the decades old conundrum of using Bond Indices to calculate SAG specific energies for SAG mill based circuits has been solved.

Jan 1, 2012

By Cedric E. Gregory

"A study of model rectangular mine shafts has been made in the wind tunnel, with the aim of reducing air-flow resistance elements to a practicable minimum. An analysis of Table 7 shows an indicated average decrease in resistance of 28 per cent by adopting the over-all modifications involved in the configurations actually tested. Much greater reductions (up to 68 per cent) are indicated by extrapolating beyond the test results directly achieved. Intermediate partial reductions in aerodynamic resistance are shown for individual modifications, such as: (1) about 3 per cent for locating the lagging in the No. 4 (inside flush) position as against the No. 1 position - 8 per cent as against the No. 2 position - and 23 per cent as compared with position No. 3; (2) about 12 per cent for using lagging instead of steel meshwork along the divider separating the skipway from the service compartment; (3) about 14 per cent for using steel gridwork ladder stagings at 3-set intervals instead of similarly spaced wooden stagings; (4) about 12 per cent for using steel gridwork ladder stagings at 3-set instead of at 1-set intervals; (5) about 13 per cent for fitting a streamlined fairing (see Fig. 5) to the upstream face of the skipway divider. Contrary to expectations, an advantage of only 3 per cent is indicated for lagging in the inside flush (No. 4) position over the outside position (No. 1). This slight gain does not appear to warrant the cost of moving the lagging. However, if the lagging is already in the No. 2 or No. 3 position, there is an 8 and 23 per cent advantage respectively."

Jan 1, 1973

By T. T. Tigert

INTRODUCTION THE PURPOSE of this article on methane is to present the simple basic facts of the characteristics, detection, occurrence, and control of this natural gas in metal mines, so that operators and .safety men may deal with it with some degree of confidence. Fortunately, although methane has been noted at many metal mines throughout Canada, the occurrences usually are small flows of short duration, and the ignitions experienced have, in most cases, had minor consequences. However, methane does present a hazard that can be of serious proportions, and ?any complacent attitude toward this gas that might exist in the minds .of people engaged in underground mining operations should be dispelled when it is ,pointed out that, in Ontario alone, ignitions of this gas have resulted in at least four fatalities, and eight men seriously injured and burned, during the past three years. lt is well-known that liberation of methane can and does .occur suddenly, often in mines where no gas has been found before, and that many ignitions and explosions have occurred in so called non-gassy mines. In view of this, it is apparent that no mine can, with any degree of certainty, be classified as non-gassy. CHARACTERISTICS OF METHANIZ The characteristics of natural gas encountered in most of the Ontario mines indicate that methane is the chief constituent. Methane (CH4), commonly termed 'marsh gas', and by the coal miner 'firedamp', is a colourless, odourless, and non-poisonous gas considerably lighter than air, and is the explosive gas frequently found in coal mines. Its physiological effects, closely resemble those resulting from nitrogen.

Jan 1, 1951

By J. Weyer

"Threshold limit values (TLVs) for NO and NO2 have been reduced drastically in 2016. Emissions of diesel engines have been reduced in the last decades. In many cases this is not enough to stay under required TLVs. Remaining gas in the blasted rock is set free during loading and transport. At the end, only a combination of measures with a further reduction of diesel motor emission, replacement of diesel driven vehicles by electric equipment, new explosives with reduced NO and NO2 production, changes in the organization and effective ventilation measures can ensure that the TLVs are not exceeded. KEYWORDS Blasting fumes, Gas measurement, Gases, Threshold Limit Value (TLV) SHORT HISTORY OF EXTRACTION OF RAW MATERIALS The extraction of raw materials—besides haulage and transport—is one of the main processes in mining and tunneling. The principal objective is the creation of a material which can be transported from the place of extraction (face) to another place for further processing or direct use. Furthermore, recently a desired grain size distribution has become more important. A revolutionary development took place in the course of centuries. With the use of primitive tools like shovels, chisel and iron in the 12th/13th century in Freiberg, ore mines performances of 12 16 cm per man and week could be reached in cross section of 1 m2. Recalculated with an assumed average density, this is a performance of 0.006 t/h. With the introduction of black powder into the subsurface in 1627 by Caspar Weindl in the city of Schemnitz (nowadays Banska Stiavniza), performances increased. A part of the hard extraction work was now done by the explosives. But first in 1767, it was recognized in a mine in Freiberg that more than 1 hole could be drilled (hand-drilling) and blasted. This discovery was so important that a plate with an inscription describes this event. The performance was increased more than 10 times compared to the extraction with chisel and iron. Since this time, drilling and blasting has been the most important innovation force for the increase of the performance. Problems with noxious blasting fumes led to the construction of the first tunneling machine by Henry Joseph Mouse in 1846 (beside shield machines from 1825) (Stack, 1982)). The triumph of mining machines started only interrupted by the two world wars. The development of hard rock boring machines (including roadheaders) was enforced after 1945. An almost complete extraction by hard rock boring machines was predicted for the turn of the millennium. And, indeed, one could find powerful machines in Canadian potash mines which were able to mine 1000 t of potash in 1 hour. That was an increase in the performance by several powers of ten. But already in the 1980s, it was recognized that the ambiguous goal could not be reached. Problems with wear of the tools, radius of curves, minimal length of openings, size and costs of the machines led to a more or less parity between drilling and blasting on one side and machines on the other side, of course depending on the field of use. For this reason, drilling and blasting is still the dominant extraction technology for raw materials. In the development of drilling and blasting technologies, the focus was mainly on the improvement of the safety but also on the increase of the blasting power and performance. Examples are tests for the increase of the power of ANFO explosives which were carried out in the 1970s and 1980s, in the former teaching mine “Reiche Zeche”. In the 1980s vehicles for loading and mixing of ANFO explosives have been developed, the blasting cab sensitivity of ANFO has been increased, emulsion explosives have been developed and up to now further developments like PMMA LOX EX explosives are on the way. At the turn of the millennium, 6 million t/a explosives have been used worldwide. Annual rates of increase of 2% have been predicted (Weyer, 1999). Meanwhile the focus changed from an increase of the performance"

Jan 1, 2019

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal

In copper Eta plants the optimal current density setpoint depends on the electrolyte composition and temperature. However, conventional plants operate with large standard deviations. A value of 14% with current densities offsets up to ±50% is typical. For worst, during opencircuit or shortcircuit events this variation can be from -100% to +200%. Naturally, energy consumption and copper quality are compromised. Several devices have been successfully employed to reduce set point deviations. Last developments include; Optibar Segmented Intercell Bars, Outotec Electrodes Arranging Method and NTC Selective Electrodeposition Enhancers. This paper researches and compares these technologies. It is shown that short circuits can be effectively reduced in occurrence and magnitude. Moreover, 95% of the electrodes can be forced to operate within ±10% of the set point. The specific energy consumption is reduced from 2,000 KW per Ton to values close to 1,900 KW per Ton.

Jan 1, 2011

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By J. R. Parga T., P. J. Valenzuela G., L. S. Quiroz C., P. Guerrero G., J. L. Valenzuela G.

"Pressure oxidation is a hydrometallurgical pre-treatment process used for refractory auriferous sulfide ores. In the work reported here, a refractory pyrite ore sample from the Mulatos mine, Sonora, Mexico was characterized. The sample was subjected to atmospheric cyanidation, and simultaneous pressure oxidation and cyanidation under different conditions of temperature and pressure. The mineral characterization showed that pyrite is the main species in the sample. The gold extraction tests were carried out in an 1-litre Parr pressure vessel at a temperature range of 90-120 °C, a pressure range of 87.5–150 psi (using oxygen), and a cyanide concentration range of 0.8-1.2 %wt. The gold extraction results showed that diffusion through product layer is the rate controlling step.INTRODUCTIONIn hydrometallurgical precious metals extraction, the most commonly used process is sodium cyanide leaching, as shown in the next reactions involving gold and silver (Fleming, 1992; Marsden & House, 2006):4Au(s) + 8CN- (aq) + 2H2O(l) + O2(g) ? 4Au(CN)2 -(aq) + 4OH- (aq) (1)4Ag(s) + 8CN- (aq) + 2H2O(l) + O2(g) ? 4Ag(CN)2 (aq) + 4OH- (aq) (2)“Refractory” auriferous ores or concentrates often contain gold and silver locked inside other sulfide phases such as pyrite. This renders cyanidation ineffective, so oxidative pre-treatments are used in order to convert the sulfide minerals into porous oxide minerals and make cyanidation work more efficiently. Reaction (3) shows the oxidation of pyrite in alkaline media and the formation of the porous oxide (Koslides & Ciminelli, 1992):2FeS2 (s) + 15/2 O2 (g) + 8H- (aq) ? Fe2O3 (s) + 4SO4 2- (aq) +4H2O(l) (3)A process of simultaneous chemical pressure oxidation and cyanide leaching for a flotation concentrate produced in the mine of Bacís, Durango, in Mexico, gave good results (Parga et al., 2007). In the study presented here, it was intended to use this treatment for a refractory pyrite mineral from the Mulatos mine in Sahuaripa, Sonora, Mexico, modifying variables such as pressure, temperature and cyanide concentration to find the best conditions for oxidation and leaching."

Jan 1, 2012

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By Dong-kil Lee

A ventilation improvement index (VII) was developed in an effort to propose an optimal ventilation improvement measure for a designated mine. The index was designed to incorporate both ventilation effectiveness and cost efficiency. To verify the effect of the index, a mine experiencing a ventilation problem was selected, the ventilation assessed and ventilation network analyses were conducted. In the selected mine, four areas with ventilation difficulties were detected and an improvement schemes for each area were proposed. These were simulated through network simulation and evaluated using the ventilation improvement index. As a result, an optimum ventilation improvement scheme was proposed. The improvement scheme with the highest VII value was incorporated in the design.

Aug 1, 2013

By R. W. Lawrence, O. Lopez

Many gold deposits in the world have not been developed clue to the presence of copper and other base metals which can cause metallurgical and environmental challenges clue to the formation of base metal cyanide complexes. SART technology (sulphidization-acidification-recycle-thickening) can resolve these issues by recovering copper as a high grade sulphide concentrate, recycling the associated cyanide back to the gold leach, and eliminating the downstream environmental liabilities. Project economics can be improved substantially, leading to a positive re-evaluation of new and existing gold-copper projects. Some aspects of the design and operation of two recently commissioned SART plants will be discussed.

Jan 1, 2011

By H. Paudyal, K. Ohto, H. Kawakita, S. Alam, B. Pangeni

The orange waste after lime water modification was converted into promising adsorbents for fluoride by metal loading reaction. The effectiveness and mechanism of fluoride adsorption on metal loaded orange waste gel from synthetic and real plating solution were investigated. Amount of zirconium(IV), aluminium(III), cerium(III), lanthanum(III), titanium(IV), vanadium(IV) and tin(IV) loaded on orange waste from aquearegia dissolution were evaluated to be 1.62, 1.16, 0.93, 0.95, 1.20, 1.12, 0.97 mmol/g respectively. The maximum adsorption capacity (qmax) of zirconium(IV), cerium(III), lanthanum(III), iron(III) and aluminium(III) loaded orange waste for fluoride ions were evaluated to be 1.74, 0.91, 1.07, 0.98 and 1.01 mmol/g from aqueous solution. The mechanism of fluoride adsorption by metal loaded orange waste was inferred to be ligand exchange reaction. Application of zirconium(IV) loaded saponified orange juice residue(SOJR) for real plating solution showed effective removal of trace concentration of fluoride down to the accepted standard. The negligible interference of co existing anions like nitrate, carbonate, sulphate and chloride makes zirconium(IV) loaded SOJR a promising sorbent for waste water treatment. The adsorbed fluoride from fluoride loaded zirconium(IV)-SOJR was effectively desorbed by using alkali solution for its regeneration. This work shed light on the potential application of metal loaded SOJR to remediate fluoride contaminated water for environmental relevance.

Jan 1, 2012

By V. S. Sastri, Elboujdaini. M.

"Economics of wear in mining industry and methods by which wear cost may be reduced will be discussed.IntroductionCanada loses more than $5 billion annually due to friction and wear (Table 1). It is estimated that about $1.3 billion, or about 25% of the losses, could be saved through better application of existing technology (Table 2). It should be noted that the costs given in Table 1 and 2 refer to 1986. The losses due to friction and wear and the savings would be much higher in 1996. Tribology combines the many branches and specialties in science and technology concerned with understanding and combatting friction and wear. Specifically, tribology is concerned with the design and manufacture of sliding and rolling bearings, piston rings, gears, cutting tools and other devices in which surfaces interact, in sliding or other relative motion. Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of the surfaces with the lubricants, with the chemistry, physics and use of lubricants. It is concerned with the reduction of friction and wear and the avoidance of associated failures in machinery. Similar tribological components such as bearings are used in different technologies and similar tribological problems such as abrasive wear occur in different industries. Thus, tribology is in itself a generic science and technology, concerned with the generation and dissemination of knowledge on friction, wear and lubrication, and the application of the knowledge, to a wide range of industrial products and equipment, from ploughs to space equipment, from prosthesis to engines, from washing machines to railways, from computers to power stations, from paper mills to mines. Avoidable losses due to friction and"

Jan 1, 1997

By E. Eccleston, E. Gardner, F. Letarte, R. Schonewille

"In 2005, after nearly a decade of process development and feasibility work, the commercialization of the Falconbridge Nickel Smelting Technology (NST) began in earnest with the design and construction of a grassroots ferronickel plant at Koniambo Nickel in New Caledonia. The NST process was developed as an alternative to the conventional Rotary Kiln-Electric Furnace (RKEF) process for production of ferronickel from saprolitic nickel laterite ores. The NST process promised environmental and energy efficiency advantages over the conventional route. A key step of the NST process involves fluidized bed pre-reduction of calcined laterite ore using direct injection of pulverized coal as the reductant. Two parallel fluidized bed reduction roasters (FBRs) were installed at Koniambo Nickel, each designed for a maximum capacity of 4,200 MTPD of calcined nickel laterite ore. This paper describes the process development and scale-up of the fluidized bed pre-reduction process, the design challenges associated with the prototype commercial units, and the current status of the FBR operation at Konaimbo.INTRODUCTION In the mid-1990s, Falconbridge began to develop a new flowsheet for production of ferronickel from nickel laterite ores. The process that developed came to be known as the Falconbridge Nickel Smelting Technology (NST). The flowsheet, which is particularly appropriate for saprolitic ores, involves several major unit operations, including: drying in a hammer mill-flash dryer, calcination and preheating in a flash calciner, pre-reduction in a fluidized bed reactor, and smelting in a DC arc furnace to produce the ferronickel product. This paper focuses on the fluidized bed pre-reduction step of the process and provides an overview of the process chemistry, laboratory and pilot plant development work, scale-up and commercialization of the pre-reduction step, and the results obtained in the prototype commercial units."

Jan 1, 2017

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By C. Butcher

Numerical simulations of straight tube hydroforming of a dual phase steel were performed using both upper and lower bound constitutive models for porous ductile materials. The Gurson model is based upon an upper bound approximation to the material behavior and thus overestimates formability. Conversely, a lower bound solution to Gurson's unit cell geometry was developed by Sun and Wang to provide a conservative estimate of formability. The effect of a compressive axial load (end-feed) on damage development and tube formability is investigated. The resulting upper and lower bound models successfully captured the experimentally determined burst pressure, formability and failure location.

Jan 1, 2010

By Edward P. Barrett

Iron ore, when subjected to reducing gases at a temperature suitable for reduction of the oxide but not high enough to melt the ore or metal formed, is converted into metallic iron. The product, being the original piece of iron oxide minus its oxygen, is sponge-like in appearance when viewed under a magnifying glass, and hence is called 'sponge iron. Sponge iron was probably the form in which some of the first iron was recovered from the ores. As early as the eighth century the Catlan forge developed into a low shaft furnace known as the high bloomary, in which iron was produced in the form of a pasty mass. These furnaces were increased in height, and with increased temperatures came the production of liquid cast-iron, at first undesirable because of lack of knowledge of methods for working it. In 1340 the first true blast-furnace was built iri Belgium. Some castings were made, but the greater part of the iron was converted into wroughtiron blooms by a crude puddling process. Charcoal was the universal fuel until the latter part of the seventeenth century, when coke was first used in England. Larger scale developments of methods of refining pig-iron followed. In I 885 Bessemer built his first converter in England, and within a few years the Siemen' s regenerative open-hearth furnace was developed, also in England, to produce steel. Then followed the enormous expansion in the metallurgy of iron. The idea of a direct process for the production of iron and steel has persisted during all of this time.

Jan 1, 1925