Search Documents

By F. W. Gray

Ideal utilization of the heat energy in coal should theoretically be secured by supplying each atom of combustible material present with the exact quantity of oxygen necessary for complete combination. An intimate and equal admixture of the fuel particles with air is therefore to be sought. Coal, or the combustible substances of which coal is composed, may be used in solid or liquid or gaseous form. The use of coal in small particles intimately mixed with air is, in effect, a specification of coal in pulverized or dust form. There has been much important development of this manner of using coal, which may be instanced as the outstanding advance in the use of coal as a solid. The completeness and efficiency of combustion in a properly designed dust-fired furnace permits the use of locally available coals of inferior quality, and enables them to be used commercially instead of imported coals of better quality. That is to say, some grades of coal of low calorific value, that are not economically useable in lump form on grates, are useable in pulverised form, because of the more complete combustion thereby obtained, and the consequent more efficient results. In the case of coals that are unsuitable for steam-raising in grate-fired furnaces, because of clinker troubles, (arising usually from a combination of high sulphur content and low-temperature fusibility of the ash content) use in pulverised form has obvious advantages, and in addition gives the benefit of any heat units that are contributed by free sulphur in the coal.

Jan 1, 1924

By P. Mišcevic, B. Kavur, I. Vrkljan, N. Štambuk Cvitanovic

It is known from earlier and recent research that mechanical properties of intact rock like uniaxial compressive strength (UCS), Young's modulus (E) and Poisson's ratio (?) are influenced by shape deviations of test specimens as deviations from the ideal cylinder. That impact can be significant at certain level of inaccuracy of specimen preparing, and it should be objectively evaluated and controlled in testing. The effects of intact specimens side straightness, ends flatness, ends parallelism and perpendicularity to the specimen axis, on UCS, E, and ?, measured in several actual ways during laboratory compression tests, were determined by previous research on 90 homogeneous specimens of limestone. In this paper, we subject these new experimental results to Response Surface Methodology (RSM) to model the mentioned dependence, to identify significant connections of variables and to evaluate the conclusions obtained directly from experimental phase. This study indicates how the responses of the model (outputs) – parameters UCS/E/??of limestone rock depend on factors (inputs) – parameters of specimen shape deviations like flatness R, parallelism P and perpendicularity O, assuming modern test machines with spherically seated upper platen. Starting from general RSM model with three factors (R, P, and O), we investigated the multiple linear regression models of specific mechanical property (UCS, E, and ?). Using the NCSS program ("NCSS 2004 and PASS 2005") in several steps, final models with very high coefficients of determination were developed for properties with the most evident effects of specimen shape deviations: nine models for strength UCS and UCS50 (equivalent UCS for specimen with 50 mm diameter), and three models for ?L (Poisson's ratio calculated from axial deformations measured on the entire specimen length). These statistical models with their response surfaces further strengthen and confirm the results and conclusions from the experimental phase. The critical values of R, P, and O are established using an additional statistical analysis to determine the lower and upper engineering limits. These findings set the basis for the new eligibility criteria for specimens of limestone (and similar rock with UCS about 100-150 MPa) in further testing of strength and deformability.

Jan 1, 2015

By Chris Twigge-Molecey

"Over the last 50 years there has been a dramatic evolution in the metallurgical engineering field in Canada. In the 60s the field was dominated by large American and UK groups, often selling major process and equipment packages. The local content was limited to wrap around facilities and the civil and structural work. The mining and metallurgical companies had strong internal teams to lead these projects. Over the decades and business down cycles the large foreign contractors disappeared or re-structured and the mining companies largely shed their engineering and project management groups. The resulting gap was filled by a cadre of local specialist engineering companies, some of whom have grown to be world leaders in the field. The paper traces this evolution and examines the underlying causes and consequences."

Jan 1, 2015

By W. B. Gallup

"The Athabasca Bituminous Sands have been subject to sporadic investigations since the beginning of the century. It is probable, however, that much of what has been learned and achieved concerning the deposit has been accomplished in the last few years.Current exploratory techniques, generally speaking, involve a moderate amount of coring. Electrologs and often radioactive logs are run on most holes and certain types of these archieved excellent qualitative analysis when backed up by some core analysis for calibration. Exploration - is moving back from the river and consequently a permanent network of access roads has been developed within the last few years. Most of the operations take place in the winter time. There are about 90 permit holders at the present time.Some exploratory techniques are set up to go into recovery experiments where rich tar beds are found. It is probable that in the final analysis there will be several successful methods of extraction and that both mining and various in situ techniques will be applicable depending upon the problem locally."

Jan 1, 1960

By D. D. Campbell

The Hat Creek coal deposit s occur within folded and faulted Tertiary (Eocene) strata of the Coldwater Group, which comprises weakly lithified shales, siltstones and conglomerates underlying the floor and lower flanks of the valley of Upper Hat Cr eek . This upland valley,16 miles in length and 2-4 miles in width, is located within the eastern foothills of the Coast Mountains, 120 miles northeast of Vancouver, approximately midway between the towns of Lillooet and Ashcroft, in the Interior Dry Belt of British Columbia . Most of the valley floor is covered by till and glacial outwash deposits ranging up to 500 feet in depth. Became of this overburden cover , the majority of the data on the coal deposit have been obtained from diamond drilling done during 1974?76 by the property owner, B .C. Hydro and Power Authority. Because of the limitations imposed by the lack of out crop, the Tertiary geology at Upper Hat Creek is imperfectly known; however, it appears from correlation with other coal-bearing Tertiary remnants in the southern interior of the province that these remnants, including Upper Hat Creek, may represent preserved segments of the western shoreline of a Tertiary continental sea along which deltaic swamps developed and were sustained for unusually long stable periods, giving rise to the world's thickest known coal beds.

Jan 1, 1977

By Peter Rubie

For many years, optimising the relining of hard rock grinding mills has been complicated by: ?? the large number of variables; ?? the low frequency of relines (slow feedback loop); ?? the potential economic risk associated with some changes. A technology that has its roots in the automotive manufacturing industry is being utilised to construct a statistically accurate, configurable, and dynamic simulation of the mill relining process. The effects of various mechanisation and process changes can be rapidly modelled and compared. This technology will provide mill maintenance managers and contract relining companies with the opportunity to benchmark current performance against world?s best practice. It will also provide an opportunity for concentrator plant designers and mill manufacturers to plan for maximum plant efficiency, by designing an infrastructure and equipment combination that maximises annual plant availability. This simulation tool and its associated data set, has been developed using recent grinding mill performance data from mills of varying dimensions, liner configurations, mill relining equipment, operator and tool variables. The simulation will provide an output that the various stakeholders can utilise to make optimal decisions within the given financial, physical and technological constraints of the individual concentrator plant.

Jan 1, 2012

By D. Groenveld, M. Rozou

"Recent trends move towards automation, smart sensors, internet of things, powerful DCS, and more data. Are those trends already utilized in a real time production environment? Today operators still have to monitor several complex processes at the same time and predict their behavior based on an overwhelming amount of data available.The fact of the operator being overloaded and humans being unable to process multivariable problems shows the need of a tool merging essential data and providing consistent, sound decisions for long-term profitability.This paper shows a successful execution of ABB’s process improvement services in Aitik (Boliden SA), a copper mine located in Sweden. Soft sensors, fuzzy rule blocks and model predictive control were seamlessly integrated in the control system of the grinding area, resulting in proper control of mill loads and particle size without violation of any constraints.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations. The goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. It is also crucial to execute this process step at the lowest possible energy and grinding media consumption.An optimal grinding process controller must manage to maintain a given fresh feed level while keeping the product size within a given range without violating any constraints such as power, torque or load limits. To accomplish the aforementioned, it is necessary to manipulate the ore feed rate, water feed rate and the mill speed. The most significant disturbances adding another degree of complexity to this control problem are ore hardness and the amount of circulating load."

Jan 1, 2016

By R. W. Lawrence

"In the past year, BioteQ Environmental Technologies Inc. have initiated design and construction of new plants to add to an existing list of plants that utilize the BioSulphide® and ChemSulphide™ process technologies for metal recovery and water treatment. In these plants, low cost biogenic sulfide or, in some cases, chemical sulfide reagent is used to selectively remove metals from contaminated water. The process produces high grade, marketable, metal sulfide products even from low grade feed solutions. The revenues generated from the sale of products can allow for water treatment at a profit in some cases, offset treatment costs in others, and generally reduce sludge disposal and management costs. The effluents produced from the process can meet stringent environmental standards. Current plants in operation and under construction range in sulphide demand from 50 kg/day to 3.7 tonnes/day, with the feasibility of larger plants with sulfide demands ranging from 6 to 43 tonnes/day under review.Biogenic sulfide reagent can also be considered for other applications in hydrometallurgy and mineral processing. Uses under consideration by a number of mining companies include: (1) replacement of sodium hydrosulphide in the SART process for cyanide regeneration and copper recovery in the processing of gold-copper ores, and (2) replacement of sodium hydrosulphide for use in the separation of copper and molybdenum in flotation. Biogenic sulphide, produced on demand at site, offers significant cost savings and provides the additional benefit of improved safety due to the elimination of the transportation, handling and storage required for chemical sulphide reagents.This paper reviews the applications of the BioSulphide® and ChemSulphide™ technologies for water treatment and metal recovery, and introduces projects where biogenic sulfide can be applied in hydrometallurgy and mineral processing."

Jan 1, 2007

By L O. Montpetit

The economics of the asbestos mining industry of Canada, and the physical and chemical characteristics of asbestos fibre, as well as exploration, mining, milling and quality control methods, have been described by several authors in the past few years. The scope of this presentation is to survey the application of asbestos fibres in the major product groups of the construction industry in North America. Principal categories considered include flooring materials, asbestos-cement pipes and building products, high-temperature insulation, textiles, saturated asbestos felts and asphalt com pounds. During 1962, the asbestos mining industry of Canada produced an estimated 1.3 million tons of chrysotile fibre grades, and production capacity is expanding. The market demand for chrysotile fibre, on this continent, has been in the order of 50 per cent of the production volume. The asbestos industry is dependent for growth on the construction industry. Product research is active in finding new uses for asbestos fibre; some of the new developments are presented, including the use of short-fibre asbestos grades for extending the life of asphalt pavement.

Jan 1, 1963

By F. Andrieux

"Extruded aluminum profiles are increasingly used for lightweight vehicle construction. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles, not only the stress state but also the orientation influenced both the deformation and damage behavior. For the material characterization smooth tensile tests were performed in six orientations, both stress-strain curves and r-values were registered. Moreover notched tensile and shear-tension tests were performed in three directions. Finally punch specimens were tested to investigate biaxial loading. Digital image correlation (DIC) analyses were performed to determine local strain values such as critical values at failure. Numerical investigations were conducted with the strain based damage model GISSMO, which is well suited and widely applied for crash simulation. For a strain based failure model the choice of the deformation model is crucial. Deformation models with increasing complexity were investigated to find the best compromise over all experiments. It was found that there is still a great requirement on development of a material model which describes the orientation dependence of the hardening behavior over all stress states in order to be able to use a strain based failure model reliably.INTRODUCTION Weight reduction is an important step for less energy consumption and as a consequence aluminium is increasingly used in automotive parts. An important field of application is the well-established aluminium extrusion which allows the realisation of quite complex shapes of profiles required for an innovative lightweight design with integrated functions. Typical applications are chassis parts, bumpers, crash elements, air bags, etc. Especially the Al–Mg–Si medium strength alloys of the 6000 series can be easily extruded to form complex profiles and prevail for extrusion. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles not only the influence of the stress state but also the orientation with respect to the extrusion direction have an influence on both the deformation and damage behavior and need to be characterized. The effect of orientation on deformation behavior has been intensively investigated in the last decades and material models haves been proposed (e.g. Barlat & Lian, 1989; Barlat, Lege, & Brem, 1991; Barlat et al., 2003) to describe accurately anisotropic behavior. However it can be noticed that the parameters of anisotropic material models often rely on the yield stress in different directions, which means that the effect of strain hardening is not automatically accounted for. The accuracy of the models at large deformation is not guaranteed and has to be verified. In contrast to deformation models both the characterisation and the modeling of anisotropic damage behavior are not systematically studied. Isotropic failure models based on a critical strain as function of stress triaxiality (ratio of the hydrostatic stress to von Mises equivalent stress) are widely used for crash application (e.g., Bai & Wierzbicki, 2010; Sun, Andrieux & Feucht, 2009; Sun et al., 2013). The mechanisms of failure are manifold and not fully understood; to develop an anisotropic failure model it is mandatory to also have experimental data in different orientations for loading scenarios other than uniaxial tension, e. g. shear, biaxial tension, which implies an extensive experiment plan. This makes the development of failure models more challenging than deformation models for which it is possible to develop a reasonable anisotropic model using the framework of yield function and calibrate the material parameters based on results of tensile tests in different directions. Moreover the development of deformation and failure models are intricate as the variables governing the damage evolution are predicted by the def"

Jan 1, 2018

By Mehmet Guney

This article is based on a detailed heat investigation conducted at the Rokana Division of Nchanga Consolidated Copper Mines Limited while both authors were employed in Zambia. Mindola Mine is one of the three underground mines comprising the Rokana Division on the Copperbelt of Zambia, producing about 270,000 tons of ore per month at 1.9% Cu and 0.14% Co. The total volume of air being circulated by means of five primary fan installations slightly exceeds 1,000 m3/sec at standard density. Sectional bulk cooling is practised where air cooling coils are installed at primary splits some considerable distance from the stoping operations. Total capacity of the refrigeration complex is 10,500 kw (3,500 R. tons), of which about 7,000 kw is available as effective cooling power after losses, but the heat removed from the coifs is about 3,500 kw with 61% over-all plant performance. An extension program is planned for a further five production levels with the re-deepening of a sub-vertical shaft. Thermal heat will become a major problem at increased depth associated with higher rock temperature, higher thermal conductivity of the rock groups encountered and fissure water flowing into working areas through the strata with increased rock temperature. This paper describes the ventilation and refrigeration practices in Mindola Mine, with special reference to future thermal heat problems. These are discussed with a view to mining at depth.

Jan 1, 1979

By J. A. Harle

Introduction When considering power in Alberta, there automatically come to mind ideas of either hydro or thermal generation, leaving in one's thought an uncertainty as to which one would propose. There is frequently an obvious source of power in some locations on our fastflowing rivers, the major possibilities being described in the report on Surface Water Supply and Water Power of Alberta issued by the Alberta Government in 1948, but it must be realised when reading that report that the sites so described will require extensive geological and other surveys before they can be exploited, and account must be taken also of the transmission distances involved in each instance. From a conservation point of view, where water power can be economically developed and power transmitted to the load centres, this should be done, and our thermal resources should be husbanded for our coming generations, especially if our water resources are falling owing to glacial shrinkage.

Jan 1, 1951

By B. G. Hunt, E. J. Kwasney, W. P. Campbell, S. L. Gertsman

"AbstractIn the separation of lead and zinc concentrates from the ore from Cominco's Sullivan mine at Kimberley, • B.C., an iron sulphide concentrate is also produced, some of which is roasted to provide sulphuric add for the manufacture of phosphate fertilizer. The iron oxide calcine from the roaster is potentially a valuable raw material for the production of pig iron and steel. To evaluate this material, six tons of .pig iron was produced from it in an experimental 75 k.w. electric furnace at Trail. The pig iron alone, and also in varying proportions with structural steel scrap and commercial pig iron, was used in the production of basic electric furnace steel at the Mines Branch Laboratories, Ottawa. Details are given of the steel making and fabrication procedure, of the visual and microscopic examination, and of the extensive series of tests on the steel produced. The steel produced using Cominco .pig iron in the charge showed normal working properties in all tests carried out.IntroductionTHIS PAPER describes (a) experimental work by The Consolidated Mining and Smelting Company of Canada, Limited ( Cominco), at Trail on the production of pig iron .from Sullivan iron concentrates, and (b) a joint laboratory investigation by Cominco and the Mines Branch, Department of Mines and Technical Surveys, Ottawa, to determine the feasibility of making a satisfactory steel from this pig iron."

Jan 1, 1955

By R. Blosser

Phelps Dodge introduced a process improvement model known as Quest for Zero in 2001. In 2004, the focus of Quest for Zero shifted from corporate-led initiatives to projects led by site personnel. The Hydrometallurgical Division at Morenci focused on two (2) significant process improvements: reducing electrolyte bleed and organic losses. In September 2004, Morenci kicked off a bleed reduction project to reduce electrolyte bleed by 45%. By the end 2005, electrolyte bleed was reduced by 55% through understanding and reduction of variance. Significant process changes made during this time period include changes in acid-addition strategy, reduction of uncontrolled bleed, and optimization of bleed placement. In April 2005, the organic reduction project began with the goal of reducing losses by 15%. Operational improvements during this project included improved organic recovery systems, mixer speed optimization, and picket fence installation. By the end 2005, this project reduced organic losses by 35% and current losses are 48% lower than at the start of the project. These projects and smaller Questfor Zero projects have resulted in sustainable annualized savings of $13 million in Morenci hydrometallurgical operations. Through the use of Six Sigma tools, process variances can be controlled and reduced.

Jan 1, 2007

By Hugh P. Godard, K. Winslow

"AbstractA number of panels of various aluminum alloys in different combinations and secured by steel and three types of aluminum rivets were exposed underground at two locations in a Northern Ontario gold mine for two years and then examined to determine the extent of corrosion. The results indicate Alcan 65S-T to possess considerable advantages over Alcan 178-T, which has been employed in the construction of light skips and cages with considerable success for almost twenty years. Information on the behaviour of these alloys when used with steel rivets and in mixed combinations with themselves was obtained.IntroductionBy the complete substitution of aluminum alloys for steel in the fabrication of mining skips and cages, their weight can be reduced as much as 50 per cent. Lesser savings are possible though its savings are possible through its plates, doors, reinforcing members, etc. Reduced weight leads to economy through increased hoisting efficiency.For a new installation, the basis of design is the rate of production, which thus fixes the live load to be hoisted per trip. A lighter skip permits the use of a lighter rope and a smaller hoist. In deep shafts with high-speed hoists operated in balance, the power required for accelerating is considerable. The hoist size is determined by the weight of skip, load, and rope plus the force required to accelerate or decelerate these three elements A light skip may result in a considerably lighter rope. This is important because, even though the skip can be completely balanced this is not true of the rope. Partial balancing is possible, but conical hoist drums or other devices for this purpose are costly; thus a smaller rope results in a smaller hoist, with consequent general reduction in cost of the whole installation. A reduction in power consumption is also obtained as a result of keeping to a minimum the amount of unbalanced load and the weight of all moving parts which must be accelerated."

Jan 1, 1950

By R. Vracar, D. Sinadinovic, Ž. Kamberovic

The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions aiming to get products with favourable technological characteristics from which precious and other useful metals can be recovered. A high partial oxygen pressure (1.5 MPa to 2 MPa), high leaching temperature (190°C to 200°C), pulp density 80 g/L to 240 g/L, ore fraction size 76 µm and leaching time up to 4 hours yield good results in rich ores. The full extent of copper and zinc conversion as well as a high extent of iron conversion has been achieved, while lead, gold and silver and a minor part of iron remain as a solid residue among gangue minerals.

Jan 1, 2001

By A. -M. Lafront

The corrosion resistance of die-cast and freely-solidified and electromagnetically-stirred thixocast AZ91D alloy has been studied using electrochemical noise technique in a 0.05M NaCI solution at pH 6.1 and 25°C. Specimens polished at different depths were immersed for a period of 75 min in order to assess the influence of the microstructure on corrosion kinetics and morphology. At depths between 10 and 50 µm (skin), all specimens showed general non-uniform corrosion with the lowest corrosion resistance. Between 100 and 200 µmn (interior skin), the observed corrosion was accompanied by superficial undefined pits due to metastable pitting. The corrosion form for 100-200 µm gave the best corrosion resistance. Stable pitting corrosion was observed beyond 400 µm deep on the bulk specimens. The skin of all thixocast specimens prepared billets showed a more corroded surface than that of die-cast. The interior skin as well as the bulk specimens showed better performance than that of the die-cast specimens.

Jan 1, 2007

By Charles Camsell

If it were necessary to preface a discussion of the mineral position of the Empire by justifying one's interest in that subject, there are two points that at once suggest themselves by way of vindication. Tremendous Growth of MINERAL Consumption The first of these points has to do with the general question of the world's mineral consumption. Most thinking persons appreciate in a more or less vague way the vital rôle that has been, and is being, played by mineral products in building up the material side of our modern civilization. But, apart from that casual and almost subconscious appreciation, very few have any precise knowledge of the extent to which the growth and the operation of our vast present-day industrial structure has been made possible by, and only by, a tremendous increase in the consumption of mineral products of all kinds. The increasing use of minerals confronts us today at almost every turn. It does not matter in what direction we look-at the expansion and the change in transportation facilities, in the air as well as on land and on sea; at the increasing mechanization, not only in factory and mill but even in our domestic life; or at the constantly widening use of machinery for all phases of farm production-everywhere we meet the same phenomena of rapidly growing uses of equipment produced mainly from minerals. Without resorting to any tiresome statistics, a few figures may suffice to indicate with what enormous strides the world's mineral consumption has been advancing. The figures for recent years may be open to objection on the plea that, ever since the outbreak of the world war, conditions have hardly been sufficiently normal to give us trustworthy data-we have been living under extremes either of depression or of abnormal stimulation. During the last decade before the war, however, from 1903 to 1913, the world was moving along in a quietly prosperous manner; and we have figures, or at least reasonably reliable estimates, as to the growth in mineral consumption during that decade.

Jan 1, 1932

By Huan-Qiang Zhang, Gang-Hai Huang, Yu-Yong Jiao, Fei Zheng, Zhang. Xiu-Li

An efficient and accurate three-dimensional (3-D) contact detection algorithm is of vital importance in large-scale computing of discontinuous deformation analysis. The contact detection algorithm takes up a large proportion of the whole calculation time because of the increasing calculation number in three-dimensional case. For block systems which consist of convex polyhedrons, the efficiency and accuracy of the contact detection algorithm is a great challenge. The presented contact detection algorithm in discontinuous deformation analysis (DDA) method is carried out in three phases: the global neighbour searching, the local contact type searching and the contact transferring. A contact detection algorithm for 3-D DDA is presented with some improvements on the three phases. A grid-based global neighbour searching algorithm is used to eliminate unnecessary neighbour blocks to the exact number. The local contact type searching includes two steps. In the first step, the common plane method is used to determine the contact type between convex polyhedrons. In the second step, the contact pairs detected by the common plane method are divided into four basic types. In the third phase, the four contact types are transferred into two basic contact types, vertex-to-face contact type and edge-to-edge contact type, which are managed in a uniform procedure. Three verification examples are calculated, the results show that the proposed algorithm based on the three contact detection phases is robust and efficient.

Jan 1, 2015

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007