Search Documents

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By T. W. Wloder

During recent studies concerning the effects that various surface treatments, surface imperfections, locked-in residual stresses and metallurgical and geometrical notches have upon the mechanical behaviour of metals and, in particular, upon their tension-bending characteristics under impact loads, it became apparent that specially developed methods and samples would be of great assistance in determining the desired data. This paper describes and discusses a number of different types of double-notched tension-bending impact samples which have been considered and examined for this purpose. The types most suitable for exploratory investigations are proposed for application in the study of the _behaviour of metals, their welds, and, in particular, their surfaces, when subjected to various notch-severities, surface imperfections, strain rates, temperatures, and constrained states of stress (i.e. the relations of the three principal stresses). It is expected that the proposed double-notched tension-bending samples and the proposed test methods will also contribute toward further understanding of the cold brittle behaviour and the notch-sensitivities of metals. The possibilities of introducing the so-called impact notch-sensitivity index and relative impact notch sensitivity of metals are discussed. Data obtained on double-

Jan 1, 1961

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

By T. N. MacAuley

"The Ingerbelle and Copper Mountain deposits are located near Princeton in southern British Columbia. They are owned by Newmont Mining Corporation's wholly owned subsidiary, Similkameen Mining Company Ltd. The property includes the Copper Mountain mine, a former producer. Ore reserves recoverable by open-pit mining are estimated to be 76 million tons containing 0.53% copper. Production commenced during 1972 at a rate in excess of designed capacity (15,000 tpd). All of the known major copper deposits in this area lie in a 14,000- by 3,500-foot belt of Triassic volcanics (Nicola Group) that is situated between a well-defined syenitemonzonite- diorite stock on the south and a variable intrusive complex on the north. The Nicola rocks consist of andesitic tuffs and agglomerates with lesser amounts of flows and some lensy siltstone layers. The orebodies are essentially disseminated sulphide deposits, although fracture-fillings are also important in many areas. Total sulphide content is usually less than 5%. At lngerbelle, and at Pit 2 and most of Pit 1 at Copper Mountain, the sulphides are chalcopyrite-pyrite. In part of Pit 1 and most of the former underground mine they are chalcopyrite-bornite. At lngerbelle the predominant alteration associated with mineralization is a pale greenish-gray bleaching of the dark andesitic rocks. This has been identified as albitization, with lesser amounts of epidote, chlorite, biotite, scapolite and calcite. This bleaching is plentiful at Pit 2, but K-feldspathization is also evident here. These orebodies can better be classified with pyrometasomatic deposits than with typical porphyry coppers. Their relationship to intrusives, the probably extensive metasomatic replacements, the evidence of pneumatolytic activity, the formation and redistribution of magnetite, and the irregular distribution of mineralization are all characteristic of this class. Deep-seated faults probably acted as channelways for mineralization; fracturing, faulting and rock contacts influenced ore localization in detail."

Jan 1, 1973

By C. H. Bertoni, A. Vachon

The Corner bay copper deposit is the first significan discovery on the south limb of the Dore Lake Complex, located at the eastern end of the Detour Lake-Chibougamau greenstone belt, Quebec. The deposit was discovered in March, 1981, after 26 years of intermittent work in the area. Mineralization is found in a shear zone cut ting rocks ranging in composition, from gabbroic anorthosites to anorthositic gabbros which have been intensely altered and deformed by at least two tectonometamorphic events. Both the copper-bearing shear zone and its host rocks are cut by a large NE-striking gabbro dyke. Most of the known mineralization is found east of the dyke, but two deep exploration holes have shown that the down dip extension is present to the west of the dyke. The mineralized shear varies from one to 15 metres in width, strikes around 010° and dips from 70° to 80° to the west, and has been tested for a length of 700 metres. The wall rocks are usually chloritized and silicified. Mineralization is characterized by chalcopyrite, pyrite, molybdenite, magnetite, and sphalerite occurring mainly as the matrix to quartz-carbonate breccias in the "main" shear zone. The predominant sulphides are pyrite and chalcopyri te as crystals or fragments. The brecciated mineralized shear shows evidence that there was at least one remobilization of the shear and it is suggested that copper-bearing fluids invaded the shear during its remobilization. The exact timing and source of mineralization are not known. Up to February 1984, 38 holes had been drilled to outline indicated reserves to a depth of 450 m of 1,5 million tonnes grading approximately 4% copper, 0.34 gm, gold and 13.71 gm silver per tonne. It is believed that there is considerable reserve potential in the block west of the gab bro dyke, the down dip extension of the main zone.

Jan 1, 1984

"The rocks of Notre Dame Bay form part of the Central Paleozoic Mobile Belt (Williams, 1964) of the Newfoundland Appalachians. The Central Paleozoic Mobile Belt of the northern part of the island consists predominantly of Lower and Middle Ordovician rocks overlain by Silurian elastic and volcanic sequences and underlain in the marginal zones of the belt by polydeformed metamorphic rocks of the Gander Lake Group (Kennedy and McGonigal, 1972) in the northeast and the Fleur de Lys Supergroup (Neale and Nash, 1963; Kennedy, Phillips and Neale, 1972) in the northwest. The Ordovician rocks of the Central Mobile Belt have been subdivided into a number of local groups in different parts of the region. The Lush's Bight Group was first defined by MacLean (1947) . Recently Marten (1971) has revised the definition of this group, as shown in Table 1 and his revised definition is accepted in the present paper. Plate tectonic models that have been proposed for the development of the Newfoundland Appalachian System have indicated that the mafic volcanic rocks of western Notre Dame Bay represent oceanic crust (Bird and Dewey, 1970; Dewey and Bird, 1971; Church and Stevens, 1970) which marks the remnants of the proto-Atlantic Ocean first proposed by Wilson (1966) . Such models infer that the mafic volcanic rocks constitute the upper part of an ophiolite sequence. Analyses of the lavas show that they are tholeiitic and support this conclusion (Papezik and Fleming, 1967; Smitheringale, 1972) . A complete ophiolite sequence, consisting of peridotites overlain by gabbros, overlain by a sheeted diabase dyke complex which passes upward into pillow lavas, occurs at the base of the Snooks Arm Group (Upadhyay et al., 1971 ) . Sheeted diabase dykes are known to underlie the lowest mafic pillow lavas of the Lush's Bight Group at several localities in Notre Dame Bay (Strong, 1972, and pers. comm.) . However, several conflicting points about the geology of this region suggest that although a typical oceanic crustal sequence of Lower Ordovician age is present, older rocks occur within the ophiolite terrane in several places (Williams, Kennedy and Neale, 1972) ."

Jan 1, 1972

By X. (Mike) Yao

Rock mechanics engineers must provide ground support designs that ensure a safe underground working environment. Unexpected falls of ground are unacceptable while ground support systems must be adequate. Ground support must be economic for the area supported and the time frame the opening is in use. While numerical modeling can be used for ground support design, empirical models are still the common useful design tools. Empirical models are best developed and improved from local experiences although some models, such as Stability Graph (Potvin et al, 1992), are in extensive use by the Canadian mining industry. To determine the adequacy of ground support practices at HBMS, a database of 50 fall of ground case histories between 1985 and 2001 was compiled. For each failure, the recorded data included: location, rock type, rock mass conditions, opening and failure geometry, installed ground support and failure mechanism. An analysis of the database was done to obtain an understanding of failure frequency association with rock types, stope geometry and installed ground support, and to assess what support design changes were necessary. The paper describes changes made to ground support and mining practices during the last five years, and the formation of new ground support standards and practices which have been successful in reducing ground falls while providing improved, efficient and economical ground support.

May 1, 2002

By Rita Michael

"The Marmara Ironworks was not the earliest ironworks in Ontario, but it was distinguished from other early works in a number of ways. It was established on an ambitious scale as a self-sufficient and, for the time, sophisticated community. In effect it was an iron plantation on the scale and scope of those at Hopewell, Pennsylvania and Saugus, Massachusetts(1). It was, besides, the only one of the few early ironworks in Upper Canada which operated almost to the end of the nineteenth century, albeit in fits and starts, and which used magnetic ores rather than bog iron ores (limonite). Furthermore it is the only works which has produced archaeological interest over a number of years. The ironworks is on the east bank of the Crowe River near Highway 7, on Lots 7 and 8, Concession 4, Marmara Township, Hastings County, Ontario. It is the property of the Village of Marmara, and the extant remains encompass about 2. 5 acres of the original 2000 or so which made up the original grant. The mineral riches of the Canadian Shield had been known since the days of the Jesuit missionary-explorers. A consortium headed by Alexander Henry and the Duke of Gloucester planned to exploit the copper near Sault Ste. Marie during the last part of the eighteenth century, but nothing came of the venture(2). This attempt may have grown out of Lord Dorchester's suggestion that private enterprise be encouraged in order that the iron ore which ""abounds"" in Canada might be exploited(3). John Graves Simcoe, the first Lieutenant Governor of Upper Canada was also anxious to see iron working develop. Simcoe was eager to encourage many enterprises, among which ""the development of iron mines""(4) - Governor Gore had been approached by John Mason for help with his ironworks in Norfolk County (5). Three Americans had applied for permission and support to erect an ironworks on the Gananoque River at the falls to become known as Furnace Falls. They were granted 1000 acres of land in fee simple to encourage their endeavor(6). Sir Peregrine Maitland, only a few months after taking up his duties as Lieutenant Governor in 1818, intended to visit the ""bed of iron ore on the Crow River"" (7) - Maitland was to provide a good deal of support, both moral and substantive, to Charles Hayes when he came to Canada in 1820."

Jan 1, 1999

By Andreas Oberrauner

Content ? What is? an introduction ? Crushing technology ? Conveying in pits ? Pit-exiting strategies ? Mine Planning in IPCC ? Summary/Conclusions EHS slide ? Sandvik?s objective is zero harm to our people, the environment we work in, our customers and our suppliers ? Current EHS-figures will be added in August! Who is this? Andreas Oberrauner ? Born in Austria ? Living in Cologne (Ger) ? Mining Engineer ? Montanuniversitaet Leoben (Austria) 2000-2005 ? PhD on Mineral Processing 2008-2012 ? Sandvik Mine Planning Department ? Main task: Provide practical and efficient solutions for mining-challenges

Aug 1, 2013

By Joanna LaForte

"IntroductionIn respect to The Human Dimension by M. Phyllis Bray, this author's impression is that research on long distance commuting (LDC) is long overdue. This type of mining is not new to many workers, especially those from areas such as the Maritimes, who have had to look for work away from their families for at least a decade. Perhaps to the industry the over-all set-up is new, but to workers who have faced mine shut-downs in their areas finding a job was the main objective and if the security of long-term employment was evident, then the families might join them later. This was the situation with which the writer' s family was faced.LDC LifestyleBeing the wife of an underground miner, the author has personally experienced this lifestyle for almost 10 years, and has never experienced accommodation in a company town. The first five years of marriage were spent in a small rural municipality within 50 miles of the worksite, but the town had industry separate from mining and was not affected by the mine shut-down.Since her LDC lifestyle began her family has been pretty much city-based, out-of-province commuters with two children and a third to arrive some years later. She therefore lived a fairly normal married life with a husband home daily. The author has experienced life with a husband who worked away for five-day stretches and then drove long distances to be home weekends or the portion of time left over from driving and fatigue. She has done the 3D-days in/l4-days out routine, and for approximately the past four years has been existing on a two-weeks in/two-weeks out ritual .The author does not agree that the ""bottom line is that mining families go where the jobs are"" . The miners go where the jobs are and the families fend for themselves with the assistance of the pay cheque making it home each pay period.Perhaps because there are many personal frustrations with this type of lifestyle, perceptions may be inaccurate. Having only dealt with underground operations, there may be gross differences between the pressures and demands of other forms of mining."

Jan 1, 1991

By G Anders

Underground tests of slusher cables at first might seem to be quite simple and inexpensive. They do, however, take a long time and give results that may be ambiguous and unreliable. Also, because underground test conditions are not exactly duplicable, tests carried out at different times or in different mines could not be compared. An attempt was made to develop a laboratory test method that would provide for all factors affecting slusher cable performance underground in such a way as to make it possible to achieve comparable results from different series of tests by exactly duplicating test conditions. Such a method should also make it possible to vary individual factors systematically in order to give a proper assessment of the effect of changing conditions on cable performance. A set of tests, comparing the same two types of cable both underground and in the laboratory, is described. AN assignment at the Algom Nordic mine called for the comparison of two types of %-in. slusher

Jan 1, 1964

By T. A. Utigard, S. Pedler

Ilmenite from the Everett deposit in Quebec was characterized both chemically and mineralogically. The sample investigated contained the following main components: 40% Fe2O3, 21% TiO2 and 21% SiO2. The ilmenite grains contained about 20 to 25% hematite intergrown blades, with widths ranging from 2 to 30 \u03bcm. Crushing the sample to less than 0.85 mm led to significant liberation of the ilmenite from the gangue minerals. Gravity separation followed by magnetic separation of this size fraction led to a TiO2 concentrate grading of about 30% TiO2, with a recovery of 94%.

Jan 1, 2010

By E. Yan, M. Mankosa, E. Wasmund

"Rougher flotation in sulfide ore applications is typically performed using conventional flotation machines. The trend over the last 100 years has been for these cells to become larger in volume with cells reaching sizes of 600 m3 and in some cases even larger. The associated foundation loadings, transport and installation requirements along with building size have also increased. In an economic environment where projects must be executed with dwindling capital supply, bigger is not always better. More recently, industry is being challenged to identify new technology that allows for improved flowsheets and financial returns through efficiency gains. To meet this challenge, a novel high-intensity two-stage flotation system known as the StackCell™ was tested to potentially achieve installation volume and required retention time gains when compared to conventional flotation circuits. The results from on-site pilot scale work conducted on typical copper concentrator rougher flotation feed showed retention time gains on the order of 6 to 9 times when compared with conventional flotation equipment. This finding has the potential of reducing capital demands for rougher flotation circuit designs when incorporating the StackCell. The results from test work will be discussed in this paper showing comparative test data generated with a Denver bench batch test, pilot StackCell and large conventional cells, all receiving the same feed.INTRODUCTION Over the last few years, a number of flotation devices have been described as two-stage or multi-stage flotation units. The idea behind multi-stage flotation devices is that flotation performance can be improved by utilizing cells with multiple specialized units in series, but not all units of the same type, as is practiced in trains of multiple tank cells or columns. Instead, each unit is specially designed to provide the optimized fluid environment for each stage of the sequential flotation process. This idea has been proposed based on a study of the fundamentals of the flotation process, and the realization that the process consists of discrete sequential processes, that are each optimized with dissimilar process conditions (Finch et al, 1995), (Zhou, 1996). Instead of executing each step simultaneously in a homogeneous fluid environment, where the conditions would be a compromise between particle collection and froth recovery, the multi-stage flotation unit operates in a set of segregated process environments, each with a set of conditions optimized for that step."

Jan 1, 2018

By Asanga S. Nanayakkara

The surface deformations induced by reservoir dilations can be measured using tiltmeters and these measurements can be used to infer reservoir level volume changes by solving an inverse problem. Preferred approach to solve such an inverse problem is to consider more tiltmeter measurements than the number of unknown variables considered in the inverse problem. However, sufficient number of measurement points is not always available due to economical and practical issues. This paper proposes a new approach to circumvent this problem. The new approach entails generation of pseudo surface deformation data by curve fitting tiltmeter measurements using a mathematical function, which delineates three-dimensional characteristics of surface deformation profiles. Then a three-dimensional inverse problem is solved using pseudo surface deformation data. This method is useful in inferring reservoir volume changes with high areal resolution when the number of available measurements is not sufficient to acquire the desired areal resolution.

Jun 1, 2012

By K. Sawada

Along with the expanding demand of copper concentrate in Asian countries, custom-smelters have confronted with difficulties of low TC/RC. Now, Japanese Copper Industry have 2 options; investment in mine development and/or recycling of copper scraps. The strategy of global mining companies is analyzed, and implications for Japanese Copper Industry will be discussed from the viewpoint of sustainability of smelters in Japan.

Jan 1, 2014

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012

"The standards set out requirements of the Toronto Stock Exchange for company’s providing information to investors, regulators and/or the media regarding their mineral properties. In addition, information contained in new releases, continuous disclosure documents [annual report], or other forms of communication [printed investor relations materials and electronic publications] are also subject to these standards.1.0 INTRODUCTIONThe disclosure of the results of exploration and development activity on mineral properties mustcomply with the requirements of the Toronto Stock Exchange Policy Statement on Timely Disclosure, theOntario Securities Act and all applicable policies and rules of the Ontario Securities Commission and anyother securities regulatory body having jurisdiction over an issuer listed on the Exchange. In particular,the requirements of National Instrument 43-101 must be followed.The purpose of the standards is to set out the requirements of the Toronto Stock Exchange when acompany provides information to investors, regulators and/or the media regarding its properties, whethersuch information is contained in a news release, a continuous disclosure document such as an annualreport, or other form of communication, including, but not limited to, printed investor relations material andelectronic publications such as Internet Web sites. These standards do not apply to prospectuses orlisting applications, the standards for which are contained in the policies and rules of the securitiescommissions and the Exchange. These standards are also not intended to establish requirements for thecontent of technical reports.Any information published by or on behalf of a company must comply with these standards. If acompany becomes aware of information published by others regarding its mineral properties which ismaterially misleading to investors, it should take appropriate action to correct such information orotherwise make it known that it is not responsible for publishing such information and does notnecessarily agree with such statements.Disclosure concerning mineral properties should identify the ""qualified person"" as defined in NI 43-101 who is responsible for the work conducted on the property and such person shall have read andapproved of the technical disclosure."

Jan 1, 2003

By D. D. Macdonald, G. Engelhardt

The accumulation of damage due to localized corrosion [pitting, stress corrosion cracking (SCC), corrosion fatigue (CF), crevice corrosion (CC), and erosion-corrosion (EC)] in complex industrial systems, such as power plants, refineries, desalination systems, etc., poses a threat to continued safe and economic operation, primarily because of the sudden, catastrophic nature of the resulting failures. Of particular interest in managing these forms of damage is the development of robust algorithms that can be used to predict the integrated damage as a function of time and as a function of the operating conditions of the system. Because complex systems of the same design rapidly become unique, due to differences in operating histories, and because failures are rare events, there is generally insufficient data on any given system to derive reliable empirical models that capture the impact of all (or even some) of the important independent variables. Accordingly, empirical models have generally failed to provide a robust basis for predicting the accumulation of corrosion damage in complex systems under realistic operating conditions. The alternative prediction philosophy is determinism, in which the development of damage is described in terms of valid, physico-electrochemical mechanisms with the output being constrained by the natural laws. The differential damage is then integrated along the corrosion evolutionary path for the system (i.e., over the future operating "history") to yield the desired integrated damage, which is the quantity that is most useful to an operator. In this paper, we review the theory of predicting corrosion damage within the framework of Damage Function Analysis (DFA), with particular emphasis on the pitting of aluminum in chloride solutions and on the accumulation of damage from SCC in Type 304 SS components in the primary coolant circuits of Boiling Water (Nuclear) Reactors (BWRs). These cases have been selected to illustrate the various phases through which localized corrosion damage occurs.

Jan 1, 2005

Between 1993 and 2003, a series of AG and SAG mill pilot plant trials were conducted using Hardinge Ical pilot plant scale SAG mills on numerous ore samples and ranging across a wide variety of operating conditions. The data from these tests were used to evaluate the design of SAG and AG mill circuits for over a dozen projects, of which about half were eventually constructed and commissioned. The data were also used in the development of SAG mill modelling, scale-up and simulation procedures by several consultants who had access to part of the data set. Recently, we have had the opportunity to bring this data together and further analyse the consolidated dataset. This paper reports on the outcomes of this analysis that has identified the impacts of different AG/SAG circuit flowsheets and operating conditions on energy efficiency and operating cost.

Jan 1, 2012

1 INFORMATIONS GÉOLOGIQUES ET PLANIFICATION MINIÈRE La notion de gisement exploitable s'appuie sur les connaissances de géologie, d'ingénierie et tablir la rentabilité en fonction des investissements requis, des coûts de production, et des revenus qui sont tributaires de la demande et des prix des marchés. C'est une notion qui est d'abord diffuse lors de la découverte et de la première délimitation d'un gisement "d'intérêt économique potentiel" mais qui doit se confirmer et se préciser par des travaux additionnels pour devenir de plus en plus quantitative et assurée. 1.1 Informations géologiques Les conditions géologiques varient d'un gisement à l'autre (forme, dimensions, attitude, concentration et continuité -litages, effets de pépites - de la minéralisation). D'autre part, chaque méthodes minière a des contraintes différentes quant aux possibilités de sélectivité d'une part, d'acquisition d'information additionnelle lors du développement de la mine d'autre part. Cette problématique a été résumée au tableau 1, modifié de Vallée et al. (1993) [tableau 5, CIM Bulletin, avril 93, p. 74.].

May 1, 2002