Search Documents

By W. W. Cummings

Canada's only current tungsten producer started up in 1962 with a small open-pit mine on the Flat River , 180 air miles north of Watson Lake, Yukon Territory. The orebody was in a contact-metamorphic skarn zone and contained about 1.5 million tons of ore grading an estimated 2.47% W03 and 0.5% copper. Near the end of the open pit , a new zone was discovered on the lower limb of the same structure, and the decision to go underground was made in 1972. The new "E Zone" contains over 4 million tons of ore grading an estimated 1.6% W03 and 0.28% Cu , and has been supplying the concentrator at about 175,0 00 tons/ year since late 1974. A continuing program of change and up-grading is necessary in the conversion from a seasonal open-pit mine with limited life to an underground operation with twenty years of reserves. Changes are necessary in plant and services as well as the mine. Also, environmental protection requirements have changed from rudimentary to rigorous over the life of the operation. This paper sums up the changes in the operation since 1971 and outlines the changes yet to come.

Jan 1, 1977

By James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determination in a series of industrial campaigns. Some frother observations are described, including: concentration evolution down a bank, distribution between pulp and froth phases, and a mass balance around a circuit. Minute amounts of frother in recycle water were also measured.The contribution of frother and alcohol by-products in the analysis was generally additive for plants using aliphatic alcohol type frothers and decoupled for systems using glycols. Typically, U250C (polyglycol) was used at higher concentration (>10 ppm) than MIBC (aliphatic alcohol) (<10 ppm) or F-150 (polyglycol) (<3ppm).The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2007

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By W. N. Wallinger

The mine and concentrator of Cyprus Anvil Mining Corporation are situated in south-central Yukon, some 120 miles north of Whitehorse. The large lead-zinc concentrator employs conventional crushing and grinding , followed by differential flotation, to produce selective lead and zinc concentrates, as well as a mixed lead-zinc (bulk) concentrate. Since the commencement of operations in 1969, the concentrator has undergone expansions and modifications which have increased the capacity to 10,000 tons per day, and afforded some metallurgical improvements.

Jan 1, 1978

By S. A. Luciani

"In 1957, an asbestos orebody was discovered in the northern sector of the Ungava Peninsula of the Province of Quebec, an area now identified as Asbestos Hill. The deposit is situated on a plateau 1700 feet above sea level and 42 miles inland from Hudson Strait. It is a bleak, iso. lated location of typical arctic environment. Fifteen years were to pass before the first shipment of ungraded fibre was made in 1972. These years we1•e occupied with field surveys and investigations, diamond drilling, engineering design, evaluation of investment and operating costs, and construction. The problems normally associated with mine development were further complicated by location, isolation, and the extreme cold and permanently frozen ground of the arctic regions. Unique to an isolated arctic operation are the organization of support facilities and services, procurement and retention of personnel, construction of access roads and airports, and scheduling of product out and supplies in during the short summer period of sea navigation."

Jan 1, 1976

By Gabriel Zarate

"Los Bronces had two ROM dump leach operations designated Leach I and Leach II. Leach I was commissioned in 1998 and stopped in 2014 due to the mine requirements. Leach II plant, commissioned in early 2002, was built to treat around 700 million tons of marginal ROM ore averaging 0.45 % total copper. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides.The original electrowinning plant design capacity for copper production was nominal 19,500 tonnes per year at a current density of 276 A/m2 and a current efficiency of 92%. Presently, Los Bronces San Francisco plant typically operates at current densities between 390 and 440 A/m2, much higher than the average in the industry, with current efficiencies around 93% and a maximum copper cathodes production of 37,200 tonnes per year.In order to accomplish these achievements, a number of modifications in the process conditions, in the cell hardware and in the operational procedures have been implemented. In the first case, the specific flowrate, copper concentration and temperature of the electrolyte were modified to accommodate the operational requirements facilitating the increased current density. Associated with the cell hardware, a six cells expansion was added, upgraded equipotential inner cell busbars were installed and the cross section of the cathode hanger bars was enlarged for increased current carrying capacity. Documented operational procedures like short circuit detection and cathode weight control were improved.The modifications implemented and the results obtained are discussed in this paper.INTRODUCTIONLos Bronces Division of Anglo American Chile is located up in the Andes Mountains, northeast of Santiago. It had two cathode plants, Los Bronces at an altitude of 3500 meters above sea level (m.a.s.l.) commissioned in 1998 and closed in 2014 and San Francisco at an altitude of 2800 m.a.s.l. and in operation since 2002.The process is leaching run off mine (ROM) low grade copper sulphide ore in dumps. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides. The average grade is 0.45% total copper (Cut).At Los Bronces dump, Leach I plant, the pregnant leach solution (PLS) was collected and stored in an underground reservoir. From there, it was fed to a solvent extraction plant with a series-parallel configuration in two extraction stages and one stripping stage. The electrolyte produced was fed to the electrowinning plant having 30 cells and 60 cathodes per cell. Maximum capacity of this plant was 12,000 tonnes per year (tpy)."

Jan 1, 2016

By F. L. Wu

Based on the analysis of a sealed coal mine resulting from a fire-triggered explosion, limitations were discovered in the re-entry procedures used to reduce the size of the sealed area that were being applied during the process of re-opening the mine. The analysis of two re-opening plans in a mine using mechanical ventilation showed that the estimation of the degree of damage of two air doors close to the working face with the fire was key to the identification of the optimum mine recovery plan. The operation points of airflow and air pressure of the main fan under either the doors? damaged or intact conditions can be estimated through the use of a ventilation network simulation program. Starting the main fan for a short time period and measuring its operation points of airflow and air pressure allowed their comparison with the simulated values. This procedure provided a reasonable estimation of the degree of damage of the ventilation structures and more confidence in choosing a recovery plan. Through this process, it was possible to conclude that the two doors were still intact. Consequently, the final plan of installing a new main fan in the main decline, sealing the initial upcast shaft and unsealing the auxiliary downcast shaft, was proven to be reasonable at the mine site.

Aug 1, 2013

"The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high variability in the continuous operations together with a shortfall in the attainment of full capacity, or higher utilisation of consumables.At a level of best practice, ‘Operational Performance Excellence’ focuses on process control, using automation and control systems to deliver process optimisation. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection / installation. It includes the appropriate selection of the right instrumentation, control system, key process knowledge, individuals with a solid control engineering background / experience, and the essential backing / support of the operations management team together leading to higher value delivery. Robust solutions can be realised, considerably minimising process variation, thus leading to process optimisation. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimised process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this paper, these questions and their possible answers are discussed."

Jan 1, 2014

By W E. vanSteenburgh

The Polar Continental Shelf Project was initiated in 1959 to provide an administrative and logistic vehicle for research in the physical sciences of the land, sea and channel area of the Arctic Archipelago. Most of the scientists are supplied on secondment from the professional branches of the Department. The yearly expeditions number some eighty scientists and sub-professional staff, and they are supported by a fleet of fixed-winged aircraft and helicopters. Accurate positioning is obtained by the use of a Decca Lambda navigational system which is moved as the area of interest is shifted. The Project is designed to accommodate not only physical scientists, but to provide facilities for other scientist who may have an interest in the area under study. The main research scope of the Project includes topographical surveys, hydrography, oceanography, geology, including marine sedimentary studies, gravity, magnetics, seismology, glaciology and geography. The Polar Continental Shelf Project was initiated and recommended by the Committee on Northern Development in 1958.

Jan 1, 1963

By G. Armand, G. Arnold, A. Giraud, C. Auvray

The knowledge and understanding of the mechanical behavior of claystone is of critical importance in the aim of nuclear wastes storage. In this study, specimens of Callovo-Oxfordian claystone (COx) have been obtained from the ANDRA underground research laboratory in Meuse/Haute-Marne (France). This claystone is composed of carbonate inclusions (10-50µm) embedded in an argillaceous matrix (representing expanding clay minerals, such as smectites). The matrix itself is also multiphase and composed of clay aggregates of 1µm-size carbonate and quartz inclusions. This multiphase microstructure leads to a high heterogeneity witch was analysed through nanoindentation test grids. Moreover, the mechanical behavior of the claystone matrix is highly sensitive to humidity and temperature. The nanoindentation tests were performed in a climatic (i.e. temperature and humidity controlled) chamber at relative humidity levels from 50% to 98% and at two temperatures: 20°C and 60°C. In a first step, the curves of indentation were analysed using the commonly used Oliver and Pharr’s approach. Other wellknown parameters as the creep factor were also extracted. In a second step, Fisher-Cripps model (Fischer- Cripps, 2004) and Vandamme and Ulm model (Vandamme & Ulm, 2006) were used to identify viscoelastic properties. A statistical analysis is used in order to extract mechanical characteristics of the different phases. Hardness and elastic modulus decrease drastically with saturation (above 80% humidity) and to a lesser extend with temperature.

Jan 1, 2015

By Son Hye Jin

Abstract ? KHNP is participating in the construction of Nuclear Power Plant both in Korea and UAE. ? We want to improve our construction project management process. ? So we are now developing the process model on nuclear power plant construction management. ? For the effective adoption of this process, we are planning to develop IT system. ? For the first step, we were established the Information Strategy Plan

Aug 1, 2013

By Richard E. J. Putman

THE MINERALS INDUSTRY has always been a heavy user of energy in most of its unit operations: power in the mining, comminution, flotation and electro-winning processes; fuel in its smelting and other metallurgical processes; and, of course, fuel in the on-site generation of power and steam. Many of the techniques for using computers to perform energy management and conservation tasks have been known for some time, but they have not been widely implemented because the return on investment has hitherto been insufficient. Recent trends, however, have not only caused the dollar return to rise due to higher purchased energy costs, but the cost of the investment to fall. One trend has been the generally lower cost of computer control systems themselves, due to vendors having adopted the newer, lower-cost and more reliable electronic component technologies now becoming universally available. The second trend is the development of low-cost, but high-speed, remote multiplexing devices, which have reduced considerably the expense of bringing data from points scattered over a wide area, which is typically the case when applying energy management systems to a minerals processing plant. By taking advantage of these and related developments, computer control systems can now have a rewarding impact on plant energy management and conservation practices, and recent advances in application technology have opened up new and additional opportunities for energy cost reduction and control.

Jan 1, 1978

By J. Dubinski

This paper describes the key circumstances of the underground coal gasification (UCG) process, which is planned to be carried out in the Polish hard coal mine ?Wieczorek?. The construction and field tests of a UCG pilot plant have key issues that need to be addressed to realize the research project goal: the elaboration of a highly effective technology of fuel and electricity production. The project will conduct several monthly tests of gasification in the pilot geo-reactor, which will be constructed based on the results of laboratory tests. The realization of the process requires numerous appropriately prepared actions adjusted to natural conditions in the hard coal deposit. Based on scientific principles, it is necessary to elaborate the procedures related to the location of the UCG installation (including its legal and safety aspects), and to perform a technical risk analysis. In addition, it is necessary to determine the required mining, geological, technical, economic and organizational circumstances, while at the same time considering the real but constantly changing process conditions.

Aug 1, 2013

By H. J. Conolly

The area around Osisko lake, the Horne mine, and the town of Rouyn, in northwestern Quebec, presents a most interesting structural problem. The present discussion is confined to an area around Osisko lake, about six miles long and three miles wide, shown in Figure 1. The writers are particularly indebted to Mr. Thayer Lindsley, of Ventures Limited, who sponsored the investigation and gave permission to publish this paper. Mr. H. L. Roscoe and Mr. Oliver Hall, of Noranda Mines, Limited, gave every possible assistance; and the Noranda geologists, Mr. H. M. Butterfield, Dr. Peter Priee, and Dr. G. G. Suffel, contributed many data and ideas. It is a pleasure to acknowledge also the fuidance of Dr. W. F. James and Dr. B. S. Buffam and the full use made o their maps and criticism. Dr. M. E. Wilson and Dr. A. Lang, of the Geological Survey of Canada, kindly furnished data on the geology in neighbouring fields. Mr. E. Bailey assisted ably in the field, and Mr. H. F. King kindly reviewed the text. Memoir 166 of the Geological Survey of Canada, The Geology and Ore Deposits of the Roztyn-Harricanaw Region, Quebec, by Cooke, James, and Mawdsley, proved an invaluable source of information. STRATIGRAPHY The following stratigraphie sequence is based in part upon the interpretation of the structure as outlined in this paper:

Jan 1, 1936

By M. Abdollahi, M. R. Khalesi, Y. Kianinia, A. Khodadadi Darban

High cyanide consumption during the processing of gold ores with high sulphide minerals can make the typical cyanidation uneconomic. Also cyanide is a toxic material and environmental concerns of cyanide compounds are serious. Optimization of cyanide consumption requires a methodology to estimate the amount of exposed cyanicides, the kinetic of their dissolution and estimation of formation of cyanide complexes which consume the free cyanide. In this paper, a methodology to estimate cyanide consumption by modeling the minerals and gold leaching kinetic based on a liberation model and speciation of all possible cyanide related species in the solution is presented. The results showed that this methodology could successfully estimate the cyanide consumption based on mineralogical data with very lower number of parameters compared to empirical models present in the literature, while it offers the prediction of formation of all cyanide complexes which could be used for optimization purposes.

Jan 1, 2017

By Francisca San Martin, Tomas Vargas, Willy Kracht

"In Cu-Mo deposits it is usual to find considerable amounts of pyrite (FeS2). When processing this kind of ore by flotation, pyrite is rejected using lime to increase the pH to alkaline conditions (pH ~10.5). In the case of using seawater without pre-processing, i.e., raw seawater, the lime consumption increases dramatically and the recovery of molybdenite drops due to the precipitation of magnesium hydroxide on its surface. In order to avoid these negative effects, alternative ways of depressing pyrite should be considered.The current work introduces the use of Acidithiobacillus ferrooxidans, bacteria commonly used in bioleaching, as an alternative to depress pyrite in seawater flotation. The paper presents the results of biodepression in three systems: fresh water, water with added sodium chloride at 35 g/L (which corresponds to the salt concentration in seawater ) and seawater. The results show that it is possible to bio-depress pyrite with A. ferrooxidans in natural seawater pH (7.8-8.2). A similar behaviour is observed when running the experiments in fresh water, and in water with sodium chloride added.INTRODUCTIONWater is a scarce but essential resource for human development. The main reason for this scarcity is that, although 70% of the earth's surface is covered with water, only 3% of the total is fresh water and an important part of this water is frozen, so that only 1% of fresh surface water can be used for human activities. In Chile, most of the mining activity is concentrated in the north of the country, located in the Atacama Desert, considered the world's driest desert. That is why some mining companies have chosen to use seawater in their processes. For example, Esperanza (Antofagasta Minerals), and Sierra Gorda (KGHM International) use raw seawater in their flotation processes."

Jan 1, 2016

By Y. G. Yaroshenko, V. Y. Baldin, Y. M. Gordon

The manufacture of sulphuric acid from the off-gas of pyrometallurgical processes in the production of heavy metals is one of the common methods of effective recycling of sulfuric anhydrite. The new Impact-Inertial Devices with the rectangular contact channels (IIRCh) and the internal circulation of liquid allow the injection of an absorber into the phase&apos;s interactive cell by utilizing the gas stream energy and by this way increasing the sulphuric acid yield and reducing the power consumption. These devices have the following advantages: simplicity of design, smaller size, low capital expenses, absence of irrigating system, high operational reliability, simultaneous cleaning of solid, gaseous and liquid impurities and also cooling of gases etc. The IIRCh efficiency is almost 18 % higher and they require 1.3-2 times lower energy when compared with Venturi Absorbers. Also the elevation of spraying nozzles or injectors is 1.5 times lower in the IIRCh case.

Jan 1, 2004

By J. R. Gordon

I-Introduction The possibility of adapting low-temperature reduction methods to the treatment of iron ores has been suggested on numerous occasions. Papers published on the subject include, notably, Bulletin 270 of the United States Bureau of Mines on The Production of Sponge Iron, the Symposium of the American Electrochemical Society (1927) on The Gaseous Reduction of Ores and Other Metallic Compounds, and Les Procédés Actuels de Traitement Direct du Minerai de Fer, by A. Mayer (Revue de l&apos;Industrie Minerale, Nov. 15th, 1932) (1). The present paper contains the results of an investigation of the reducibility of some Ontario ores. The concentration of these ores and of the products of reduction has also been investigated.

Jan 1, 1933

By Niklas Willemsen

Introduction to SVCs ? SVC = Static var Compensator ? Dynamic step-less control of reactive power without switching of passive components: ? Voltage control/stabilization ? Harmonics- and flicker mitigation ? Dip mitigation ? Main components: ? TCR (Thyristor Controlled Reactor) ? Tuned harmonic filters ? Control- and cooling systems ? Typical applications: ? Mine hoists ? Large mining complexes ? EAF, SAF, rolling mills, wind/solar farms etc..

Aug 1, 2013

By Ellie Condolios

Hydraulic hoisting offers a number ~f attractive features over conventional hoisting methods: small shaft space requirements; great flexibility of layout, including pick-up or delivery of the material at points distant from the mine shaft; low investment and operating costs. However, limited practical experience with this type of hoisting dictates that careful design and, frequently, extensive testing be done by competent engineers before large-scale installations are built. This paper covers the following: basic laws and design criteria for hydraulic hoisting installations; a description of a coal hoisting installation which has been in industrial operation since 1960, with a vertical lift of 600 feet and an annual capacity of 500,000 tons of -3 ~-in. coal; and a tentative appraisal of the process, including cost estimates. THE transportation of solids in water flowing through a pipe-line has, for a number of years, been common practice in dredging, public

Jan 1, 1963