Search Documents

By Juergen Antrekowitsch, Stefan Steinlechner

"Waelz oxide from steel mill dust recycling is usually sold to the primary zinc industry, where it is first charged to the roasters to eliminate the remaining fluorides and chlorides. This limits the overall amount of secondary materials which can be used because of different operating problems in the roasters. Another option, in the case where the halides are low, would be direct leaching with low or medium concentrated sulphuric acid. Unfortunately, because of the carryover of some steel mill dust, iron is also present in the Waelz oxide, reaching contents up to 5 wt.%. Since the objective is to treat the solution more or less directly by electrowinning, with only a few simple preliminary purification steps, iron in the solution is a very important factor. Various trials have been done to investigate the dissolution behavior of the iron contained in the Waelz oxide. Although the zinc extraction should reach a maximum, all other elements, especially iron, should be low. This paper describes the results of our research in this area and offers possible options for Waelz oxide utilization. There is also a focus on how other elements, present in the material, influence the dissolution behaviour of zinc and iron, and whether a loss of zinc is unavoidable, if low iron dissolution is required.INTRODUCTION One of the most important secondary zinc resources is the zinc oxide originating from steel mill dust recycling. For the treatment of high zinc containing steel mill dusts, the Waelz kiln process is the so called “best available technology” and it dominates the industry, with roughly a 90% market share. The product Waelz oxide contains mostly zinc oxide, but it also contains lead compounds and halides due to evaporation with the zinc. In addition, it contains iron and some slag compounds due to mechanical carry-over. The presence of halides limits the use of the material as an alternative concentrate for primary zinc electrowinning. Such halides can be reduced to a certain extent by washing and/or solvent extraction (see following chapter). Although lead is not troublesome and theoretically represents a second recoverable valuable metal, iron is unwanted and causes additional problems during leaching. Even though Waelz oxide is generally a highly welcome input material in primary zinc metallurgy, due to its high zinc content, it still contains halides, and in the majority of cases, the oxide must first be treated in a roasting process. Different circumstances, like accretion formation because of the lead and halogen compounds as well as unwanted cooling effects in the roaster, limit the amount of Waelz oxide which can be substituted for the primary concentrate. Another, even more limiting factor, is the allowable concentrations of chlorides and fluorides in zinc electrowinning, the last step in the primary zinc processing route (Ruetten, 2011)."

Jan 1, 2016

By H. A. Dakin

"An introduction to the metallurgical requirements of the Flin Flon concentrator reveals the magnitude of ore blending which is required in its operation of three flotation circuits. The resulting variability in flotation heads which has in-creased the separations complexity justified the development of an on-line analysis system.This paper provides a summary of the development and operation of that system. Particular attention is devoted to the problems encountered and where possible their solutions; as the requirements of accurate information and minimum downtime of the sampling system and x-ray analyzer are considered essential. The addition of a recess central computer has provided information in a more easily understood form and as well has allowed the start of automatic reagent control.An indication of the on-line analysis system's value to the concentrators' operation is provided by an examination of the plant in metallurgical data and reagent costs in previous years.The metallurgical plants of Hudson Bay Mining and Smelting lie adjacent to the city of Flin Flon on the Manitoba-Saskatchewan boundary. Plant operations commenced in 1930 treating copper-zinc ore from the local mine. In recent years ore bodies near Flin Flon and in the Snow Lake area, about seventy-five miles east, have been brought into production.By the beginning of 1973 the number of producing mines had increased to nine; with all the ore being handled by the Flin Flon concentrator. Figure l, showing mine ore assays during 1973 indicates the variation in metal content possible."

Jan 1, 1974

By D. O. Downing

"The 1990s saw enormous changes in the Canadian coal industry and the future promises to be no less turbulent. While the markets served by Canadian coal producers have changed and buying practices continue to evolve, the coal mining, or supply side, has also changed remarkably in response and now provides the basis for an interesting industry story.The dynamic situation in coal mining has led to some surprising outcomes and seemingly contradictory developments. This paper outlines the changes that have occurred, and which are still unfolding in Canadian coal mining, firstly, in terms of mining technology and productivity, secondly, in terms of corporate divestments, acquisitions and bankruptcies, and finally, in terms of resource development. The paper also outlines some plausible futures for the industry looking ahead."

Jan 1, 2002

By A. Ghasemi

An alumina-silica coating was deposited on a nickel substrate by sol-gel process, and the structures and composition were evaluated, The sols were made from aluminium and silicon alkoxide, and an acid catalyst including HCl, To produce adherent silica coatings on nickel, various additives such as surfactant, viscose additive and drying control chemical additives were introduced to the system, and appropriate drying and firing cycles were applied after dipping in solution. The hot corrosion and oxidation resistance of the coating at different temperatures were investigated, The structure and uniformity of the coatings were examined by scanning electron microscopy (SEM), The results indicate that a uniform coating of alumina silica can be produced on a nickel substrate by optimizing the composition and process variables of the sol. Coatings can protect substrates from oxidation and hot corrosion at different temperature up to 1000°C, but is not very effective for hot-corrosion resistance at 1000°C.

Jan 1, 2005

Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage. The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed.

Jan 1, 2012

By D. Laguitton, D. Hodouin, V. K. Gupta, R. Spring

"The CANMET SPOC project aims at inducing progress in process evaluation and optimization by developing user oriented software based on state-of-the-art theory. The present work is the result of a joint effort by CANMET, Noranda Mines and Université Laval to develop two computer packages: one (RTD) to calculate the residence time distribution that best describes the material transport through the mill, the other (FINDBS) to estimate the rate of breakage and distribution function of the population balance model in a ball mill. The RTD package can handle data from various experimental methods (impulse or complex tracer feed, with or without recycling, etc...). The FINDBS package provides options for the functional description oj both model parameters Band S. The full detail of the methods and programs appears in a users guide. The program capabilities and several sample runs are presented.IntroductionSimulation of mineral dressing operations by computer has been largely contained within academic and research circles and has not yet gained a status of routine practice in the ore and coal industries. It is however a matter of time before process simulators are available on every process engineer's desk to assist process optimization tasks, flowsheet design and professional training. The CANMET SPOC project (Simulated Processing of Ore and Coal) was initiated in 1980 to assist the Canadian industry in integrating computer-based methodology for process evaluation and optimization(1). Software development, documentation and transfer is one of the main priorities of the project which will mature in 1985 by releasing a complete package of manuals and programs covering sampling, material balance computation, unit modelling, flowsheet simulation and optimization . This paper is a condensed description of a typical project element in its 1982-1983 state of development. The required methodology for ball-mill modelling and simulation was consolidated an d merged to other project elements during a joint study under contract financed by CANMET and Noranda Mines Ltd . The first part of the study dealt with documenting experimental methods and software for ball-mill computer simulation. Université Laval GRAAIM (Goupe de Recherche en Automatistion Appliquée à l'Industrie Minérale) acted as sub-contractor for this part of the study(16,17). A second part dealt with applying the model calibration techniques to a large industrial data base and is reported elsewhere(2,18,19)."

Jan 1, 1984

By Franciszek Letowski

"Recovery of precious metals associated with a sulphidic matrix has an important economic effect on complex sulphide ore treatment. Because a significant portion of the silver and gold associated with pyrite are rejected to tailings during the selective flotation of pyritic Zn-Pb-Cu ore, other ore processing routes have been investigated.Direct leaching of the ore with ferric sulphate solution followed by separation of different components of the solid suspension by flotation was applied. Such a process allows for: production of zinc sulphate solution; transformation of galena PbS to insoluble lead sulphate PbS04 and its accumulation in a non-floatable fraction together with precipitated geothite FeOOH and other insoluble gangue minerals; separation of sulphur and non-decomposed sulphides in the floatable fraction.Laboratory research carried out on the ore samples from an Alaskan pyritic deposit from the Delta region indicates that gold and silver are mostly concentrated in the floatable fraction.Total recovery of zinc from the ore attains 96.5% to 98.5% after ferric sulphate leaching. About 85% of copper was extracted from the ore during the ferric sulphate and subsequent ferric chloride leaching, and about 6% of the copper remained in the non-floatable fraction and mixed fraction during the leaching-flotation step. Extraction of lead from the nonfloatable fraction during leaching with calcium chloride solution attained 98% to 99%. Extraction of silver from the floatable fraction during leaching with ferric chloride solution reached 98%. Extraction of gold from the floatable fraction during cyanide or thiourea leaching reached 71% to 89%. The results of the laboratory research are presented."

Jan 1, 1987

By R. G. Achter, E. Wilson

"This paper describes the work undertaken to renovate the Pipe Open Pit drainage system, incorporating measures to improve effluent quality. It describes the technical feat of drilling an l l-inch-diameter hole from the bottom of the open pit for a distance of 1100feet to intersect an underground drift. An innovative method of checking the inclination of this hole is also described. The paper outlines the construction required on the 1500-foot level of the underground mine to facilitate water impoundment and slime settling, as well as the instrumentation for control of water flows. IntroductionThe Manitoba Division of Inco Metals Company operates two mines-an underground mine at Thompson and an open pit at Pipe. The Pipe Open Pit is located 20 miles southwest of the City of Thompson, approximately 400 miles due north of Win nipeg(Fig. 1).Surface diamond drilling of the Pipe ore body was sta rted in 1959. In 1961, a shaft was sunk to a depth o f 1,570 feet to carry out further exploration work and obtain bulk ore samples for metallurgical testing. Site preparation to mine the upper portion of the orebody as an open pit was initiated in 1966 and by late 1967, the removal of silt and clay overburden was in progress. The contractor completed the dredging in the fall of 1969. Over 12 million cubic yards of muskeg, clay and silt was removed, which in some places was 150 feet deep over the orebody. Production began in early 1971, by which time the top three benches of rock had been excavated and the orebody exposed.The Pipe No. 2 Mine main shaft was started in 1970 and completed in 1973 at a depth of 3,160 feet. Development for exploration purposes was carried out on the 1500 and 2460 levels, and permanent pumping facilities were installed.The surface dimensions of the open pit are 2,200 by 1,600 feet, with the long axis striking northeast. The walls are designed with a 45- to 50-degree slope and the ultimate design depth is 720 feet. The present depth of the pit is 520 feet and production capacity is 6,800 tons of ore per mine day."

Jan 1, 1980

By Eugene Nel, Johan Theron, Chris Martin, Hans Raabe

"Impala Platinum Limited is the world’s second largest platinum producer, producing more than 1.7 million ounces of the precious metal last year, much of this from the UG-2 reef located in the Bushveld Complex, South Africa. As part of Impala’s ongoing expansion programme, tonnage through their principal UG-2 processing facility, near Rustenburg, was increased 40% in 2001.To accommodate the increased throughput, the role of the existing primary mills was converted from conventional semi-autogenous grinding units, to attrition and selective grinding units, operating in fully autogenous mode. The finer chromite and coarser silicate components in the mill discharge are then separated by screening and processed in dedicated circuits downstream. This way, the need to spend considerable capital to increase primary grinding capacity was averted.In the last year, considerable work has been conducted to evaluate and optimise the two downstream circuits. This has involved an optimisation programme of sampling and diagnostic flotation testing, supported with QemSCAN analysis. This paper will describe the operation of the new circuit. It will also describe some of the more novel aspects and interesting findings from the optimisation programme.INTRODUCTIONThe South African platinum industry is the world’s largest producer of platinum and the world’s second largest producer of palladium. Located in a wide area north of Johannesburg, the industry mines ores from the Bushveld Complex, one of the world’s great mineral treasure chests, containing over 70 percent of the world’s platinum, as well as extensive reserves of the other PGE (platinum group elements), chrome, manganese and vanadium. The industry employs about 180,000 people in, predominantly, underground mines, which together form an almost unbroken circle of mining operations 200 km in diameter."

Jan 1, 2004

By P. G. Semple

"In January 1985, Equity Silver Mines Limited began operation of a cyanidation circuit to scavenge precious metals from the flotation tailings. At present, this process is treating 270,000 tonnes of tailings per month and is recovering in excess of 0.20 grams of gold per tonne. To obtain these results Equity is operating a carbon-in-leach circuit that utilizes pressure stripping, zinc precipitation acid washing and thermal reactivation. A cyanide destruction circuit is also required to minimize the deleterious effects on reclaim water in the flotation stage. This paper describes the existing scavenger plant, and details the start-up problems encountered and the modifications made to correct these problems.INTRODUCTIONEquity Silver Mines Limited , a 68% owned subsidiary of Placer Development Limited , is located 38 km southeast of Houston in north central British Columbia. The geographic location of Equity Silver Mines is shown in figure #1. In September 1980, production first began with the ore being supplied from the Southern Tail open pit. In March 1984, the Southern Tail deposit had reached its economic pit depth, and since then ore has been supplied by the Main Zone pit the gold mineralization in the Main Zone is less refractory than the Southern Tail and cyanidation of the flotation tailing appeared to be a viable alternative.An extensive test program was undertaken and the results confirmed that considerable gold and silver values were amenable to cyanide leaching. A feasibility study showed that these values could be economically recovered and the detailed engineering work began."

Jan 1, 1987

By C. F. Gleeson, D. G. Sheehan

"The results of humus and overburden geochemical surveys over the Doyon, Bousquet and Page-Williams gold ore deposits are presented.These studies show that humus sampling for gold gives negative results over the Doyon deposit. The lack of response is probably caused by the presence of 1 m of relatively impermeable glaciolacustrine clay and silt that overlies 1 m to 2 m of till over the surface expression of the ore zone. By contrast, positive responses for gold occur in humus samples over the Page Williams A and C gold deposits. The ""A"" ore zone is covered by several metres of exotic calcareous till over 0.5 m to 1 m of older, locally derived till. Anomalous values for gold in humus range from 10 to 35 ppb over the orebody. Overburden over the ""C"" ore zones is much thinner, generally it consists of less than 2 m of sandy till. Trenching humus anomalies that range from 10 to 1360ppb Au uncovered the gold mineralization. The geochemical dispersal trains in till from the Doyon orebody and the Page-Williams ""A"" zone are relatively short (i.e. less than 200 m) because both deposits occur in the lee of bedrock highs that shielded them from extensive glacial quarrying. Dispersal trains from all three pyritic gold deposits can be defined using either the fine fraction or heavy mineral fraction of the till.The intensity of the gold in till anomalies over the ore zones is variable. Therefore, it would be misleading to attach rigid significant threshold gold values to overburden drilling results. Each case must be evaluated based on bedrock topography, sample density, overburden type, thickness of till, as well as size, type and orientation of the target exposed to glacial erosion."

Jan 1, 1987

"The North Star and Don Jon copper deposits lie beneath the waters of Thompson Lake, which is 12 miles east of Flin Flon, Manitoba. The deposits were discovered during the years 1949 and 1951 by diamond drilling done in the vicinity of pyritic showings on the shores of two small islands in the lake. The Don Jon ore body lies 1, 700 feet southeast of the North Star orebody and is connected with the North Star mine workings by a crosscut on the 600-foot level (Figure 1 ).Production began on January 1, 1955, at a combined rate of 200 tons per day. The ore is trucked, on 24 miles of highway, to the Hudson Bay Mining and Smelting Co., Limited mill at Flin Flon.Regional GeologyRocks in the Thompson Lake area are Precambrian volcanics, ranging in composition from andesite to rhyolite, with related tuffs and breccia. These rocks have a general north-south trend and are steeply dipping. The area is part of the Lac Aimee fault block, which probably is the southward extension of a south-plunging syncline now thrust some miles to the north. This regional deformation has produced many subsidiary zones of intense shearing and crumpling. It is in two of these zones of shearing and drag-folding that the orebodies occur. The only recognizable intrusive is a narrow diorite sill which trends northeasterly near the west shore of Thompson Lake.The North Star MineA pyritic showing, carrying some chalcopyrite, was discovered around the year 1930 on the west side of a small island near the west shore of Thompson Lake. This ground was included in a group of claims acquired by the Hudson Bay Exploration and Development Co., Limited in 1947.In the years 1949 to 1951, a diamond drilling program outlined a copper sulphide orebody. This ore zone comes to surface beneath the lake, about 300 feet north of the pyritic showing on the island."

Jan 1, 1949

By Charlie Graham, Helen Shang, Ashley Scott, Andrew Hall

"Approaches to Energy Recovery• Upgrading for electricity generation - steam turbines• Direct extraction- process improvement or space heating- support medium for animal or plant growth– fish or microalgae• Heat pumps- space heating/coolingWater Energy Grades• High (150+ °C) - electricity Generation• Medium (26 to 121 °C) - direct extraction• Low (5 to 18 °Celsius)- use of heat pump is required• Temperatures between zones will depend on circumstances for best use."

Jan 1, 2012

By Z. Z. Öztürk, N. Sarica, A. H. Üçisik, C. Bindal

"Titanium oxide films were fabricated on commercially pure titanium surfaces via anodization procedure. Anodization parameters, anodization time and voltage were altered, whereas temperature and chemical composition of anodization bath were kept constant. The main idea in this study is to obtain rough titanium-oxide surfaces. The type and feature of titanium oxide formed were observed via SEM and EDX analyses. What was revealed from SEM and EDX analyses were combined with Ti-O phase diagram in order to make judgment on the type of phases obtained, e.g. solid solution and/or compounds. Studies on the different regions of each sample showed that surfaces consist of different titanium oxide compounds with various O/Ti ratios in nano level and solid solutions varying in terms of chemistry on the same sample. Thus together rough surfaces and inhomogeneous distribution of "titanium oxides" were obtained. It was also found that when anodization time and voltage were increased, more granular surface with higher O/Ti atomic ratio was obtained."

Jan 1, 2015

By Jarek Jakubec

The new euphoria in diamond exploration brings with it a need to understand the challenges that new projects can face in different stages of the development and risks that the commercial outcomes from the new projects fall short of expectations. In many cases, the problems are related to a poor understanding of the technical risks and a failure to adequately address them during the course of investigation. Failure to evaluate all disciplines to the same level of certainty could lead to a situation where the important issues are only identified late in the project development, resulting in costly delays and financial difficulties. The diamond projects located in Canadian Arctic, with its challenging environmental, geographical, social, political and geological contexts are especially sensitive to the high variability of the outcome. This presentation highlights some of the technical aspects that could be the leading sources of risk in diamond projects and could ultimately result in inappropriate mine designs, reducing the economic outcome.

May 1, 2006

By B. R. Conard

Occupational epidemiology of the nickel-producing industry has found that inhalation exposures to certain nickel-containing substances are linked to respiratory cancers and to nonmalignant respiratory endpoints. Establishing such a linkage, however, is complicated by the fact that some diseases occur long after exposure to a causal agent (i.e., some diseases have long latencies). Furthermore, most chemical agents (especially nickel substances) vary significantly in their toxicological properties and their concentrations in workplace air have varied over processing history. Because of these complications, it is critical to understand historical exposures to specific nickel substances. To assist in this effort, the author focuses on the history of smelting and its related processes at Vale Canada’s (Inco’s) Ontario operations in the first half of the 20th century.

Jan 1, 2012

By Teresa Sikora

For over 40 years the Institute of Innovative Technology EMAG has specialized in the development of systems and equipment for laboratory and on-line monitoring of coal quality parameters, as well as the implementation of these systems and devices in mines and power stations. Some of these systems, based on advanced radiation detection techniques such as ?-ray backscattering (ALFA-06 and ALFA -06/T systems) or dual energy ?-ray transmission measurement (ALFA-06/2E ash meter), and also the ALFA-06/3E system applying microwave technology for the measurement of moisture, have had numerous applications in Poland. At present, over 100 systems and devices are used in Polish hard and brown coal mines. For over 10 years, EMAG has been specializing in the development of systems and devices, based on natural gamma measurement technology. An on-line ash meter, RODOS and RODOS Ex, based on measurement of natural gamma radioactivity of coal, has been developed and put into operation. This technique has been also used in developing the portable ash meter WALKER and laboratory analyzer GAMMA NATURA. The paper briefly presents features of the above-mentioned devices, their limits and their obtained accuracy, but in particular refers to the laboratory analyzer, GAMMA NATURA, as the first such device in the world, and presents the results of ash and moisture content measurement in hard, brown coals and potassium salts. The possible applications and advantages of the device in coal mines are discussed. The paper also presents the implementation results of the portable ash meter, WALKER, and the on-line ash meter, RODOS, that is used underground in coal mines.

Aug 1, 2013

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019

By Jessica Egan, Daniel Hodouin, Mohammed Reza Khalezi, Steve Bellec, Claude Bazin, Carl Duchesne

"A model for gold leaching was developed and implemented into a simulator. The simulator uses a description of the ore that is based on the mineral composition and precious metal content. The model accounts for the distribution of minerals and precious metals through the size intervals. An ore texture model based on precious metals and minerals grain sizes within the ore is used to predict the exposed surface of the species in the various size intervals. A model is proposed to predict the rate of dissolution of any species dissolution using the exposed surface, particle size, cyanide and oxygen concentrations, temperature, pH and agitation. The flow of slurry through a leaching tank is modelled using a parallel arrangement of perfect mixers to simulate a bypass and a Cholette-Cloutier mixer model. The simulator can be used for circuit optimization but was developed to provide an environment for learning the basic concepts of process analysis methods. Examples are given to illustrate the application of the simulator for planning tracer tests and sampling campaigns.INTRODUCTIONThe constant pressure to improve the operation of processes that are already close to optimum imposes to plant engineers to be aware of the available process analysis tools and to be able to use them to assess process operation and make a diagnosis to possible problems. Some of these tools are:•,Sampling the streams of a process;•,Data reconciliation;•,Analysis of mixing in reactors;•,Estimation of rate parameters;•,Optimal tuning and flow sheet modification;•,Automatic control and real time optimization.Although some of these tools are part of the curriculum of many university engineering programs, the students are not exposed to actual process analysis problems. In addition the complexity of the ore dressing processes compounded with unavoidable measurement errors and plant disturbances can discourage many motivated engineers. These factors often lead to an incomplete valorization of the collected data and a poor return on the investment associated with the sampling, testing and analysis of the samples.Simulators are readily available for process optimization (Yalcin and Shang, 2006) by allowing:•,The simulation of various flow sheet configurations;•,The simulation of a change of operating conditions;•,The simulation of various control strategies;•,The training of plant operators.However few simulators have been developed with the objective of providing an environment for training plant engineers and technicians to the use of tools for process analysis and optimisation."

Jan 1, 2008

By E. Rezaei

Glue is an animal protein that is used with other organic agent such as thiourea, in copper electrorefining. The concentration of glue has to be controlled carefully, because the electro-deposition process is often very sensitive to small fluctuation in the operating variable. This additive (glue) prevents rough and nodular copper cathode deposits. The nodular deposits may grow causing short circuits, which results in losses in production. Addition agents are effective in controlling metal growth; they modify the normal nucleation and lattice growth steps and refine the grain structure. In this research glue concentration was determined in an industrial copper electrolysis plant. A non-linear model with high capability was constructed and after optimizing its parameters, the accuracy and precision of the model were evaluated. For determination of glue concentration, electrochemical voltammograms in optimum condition (Differential pulse voltammetry technique, Hpulse=50 my, scan rate=10 mv/s) were plotted. Some information from voltammograms was transferred to the model as inputs and the calibrated model analyzed the information and the glue concentration was determined with high precision and accuracy. In this way there is no need to separate or add agents to remove interferences. This method has been successfully applied at Sarcheshmeh copper complex.

Jan 1, 2007