Search Documents

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

The AG/SAG circuit discharge P80 is now increasingly referred to as the ?Transfer Size? or T80 for short. From the literature it is apparent that in circuit design some approaches to the sizing of AG/SAG mills as well as the ball mills that they feed use this parameter. This paper reviews whether the use of the T80 is appropriate in this context. In the course of the review examples of AG/SAG discharge size distributions measured from range of operating circuits are used to illustrate the arguments made.

Jan 1, 2012

By C. C. Li

Traditionally, strong and stiff devices, such as fully encapsulated rebar bolts and concrete lining and arches, are preferred for underground rock support. The attention is paid to the strength of the devices in such support designs. It has been observed in engineering practice that support systems composed of stiff devices are often subjected to premature failure in high stress rock conditions. In the past decade, yield support devices have been employed to improve the performance of rock support systems. A rock support system usually consists of both internal and external devices that are installed within the rock mass and on the free surface of the rock, respectively. Great efforts have been made to make support devices yieldable in the past years, but the efforts are focused on different aspects in the tunneling and mining branches. In the tunneling branch, the focus has been put on the development of external yield devices, such as Lining Stress Controller (LSC), Honeycomb element and compressible concrete, which are embedded in shotcrete liners, while in the mining industry the efforts has been on the development of yield rockbolts, such as the cone bolt and the D-Bolt. The internal and external support devices are not compatible in their deformation capacities in the current rock support systems even though yield devices have been employed. All the devices in a support system should be deformable and compatible in deformation capacity. With such a support system, premature failure of individual support devices could be avoided and the service life of the support system is prolonged. It is a trend at present to take into account the energy absorption capacity, instead of simply the strength, of support devices in rock support design.

Jan 1, 2015

By K. J. Mintz

Conveyor belts installed in an underground mine can be a potential source of a major fire, thus the need for fife-retardant belting. A Canadian Standard, CAN/CSA-M422-M87, incorporating a small-scale flame test, a drum-friction test, a flame propagation test and an electrical surface-resistance test, has been developed to meet the varied needs of the mining industry. It is recommended that mines use Types A and B belting described in that Standard, because they will have passed the large-scale flame propagation test, rather than Type C, which does not require that test. Belting that has been approved by the U.S.A. Mine Safety and Health Administration (MSHA) may be much less fire-retardant than any Canadian approved belting.

Jan 1, 1992

By S. Pinard, A. Desbiens, R. del Villar, D. Jakelski

"During the fall of 1993, a new Pill-based control strategy was installed in the B grinding circuit at the Kidd Creek Division of Falconbridge Ltd. The control strategy was first evaluated on a grinding circuit dynamic simulator (DYNAFRAG), which permitted the discrimination between more than a dozen possible control alternatives. Once the final choice was made the necessary instruments were purchased and installed. The control strategy was configured on the plant computer and is planned to be commissioned shortly.This paper summarizes the control strategy, the design procedure, the installation and the controller tuning. Some preliminary problems posed by the process prior to implementation are also presented.IntroductionIn 1990 the GRAIIM (french acronym for Research Group on Computer Applications to the Mineral Industry) of Laval University started a research project on Knowledge Based Automatic Control (KBAC). This project is sponsored by a consortium of eight mining companies under the umbrella ofMI1EC (Mining Technology Council of Canada), the Quebec Mining Association (AMQ), CANMET and the Centre de Recherches minerales (CRM). The project also benefits from important grants from the Ministere de l'Education Superieure et de la Science and the NSREC-CRD program.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged."

Jan 1, 1994

By K. K. Panthi, P. K. Shrestha

"Displacement of rock mass around a tunnel opening varies according to the rock mass properties, insitu stress conditions and applied support in the tunnel. Such displacement is also altered by presence of bands of rock mass that differ in properties. This paper focuses on the deformation behavior of rock mass around tunnel openings at four tunnel sections in Kaligandaki headrace tunnel where extensive instrumentation was done. Based on the actually measured tunnel displacement records and actually measured support pressure; back analysis has been done to estimate rock mass properties and insitu stresses. Numerical analysis has been done to analyze and assess the deformation behavior of the rock mass around the tunnel sections.INTRODUCTION Instrumentation and monitoring of tunnel convergences have significant importance in evaluation of tunnel stability. One of the key aspects of monitored data is that early convergences can be used in estimation of long term convergence. In addition, these data can also be used in evaluation of rock mass parameters and in-situ stresses around the tunnel. Convergence around a tunnel periphery may vary according to rock mass quality. Presence of bands of different rock mass may hinder the displacement pattern in the tunnel. Particularly, displacement characteristic of tunnel periphery in schistose, foliated and deformed rock mass is altered by presence of bands of comparatively stronger rock mass, e.g., quartz veins or presence of shear seams or faults. Similar observations were also recorded in monitored tunnel sections in Kaligandaki headrace tunnel, located in the Nepal Himalayas. Extensive monitoring was done by installing multiple point borehole extensometers (MPBX) at three different locations of the tunnel periphery at four different tunnel sections. In addition, convergence measurements by tape extensometers and installation of pressure cells to record support pressures were also carried out at each of the tunnel sections. Observations showed that the tunnel convergences varied according to rock mass quality, in-situ stress and effective support pressure.Rock mass parameters and stresses have significant role in the extent of tunnel deformation, but these parameters are often unknown or difficult to predict. Back analysis based on actual tunnel displacement records and known support pressure is believed to be an important method in such endeavor. This paper performs back analysis to evaluate rock mass parameters and discusses correlation of rock mass behavior with tunnel deformation and applied support. For this purpose, the rock mass parameters are estimated from actual tunnel displacement records, mapped rock mass quality records and laboratory tested data. Then, numerical modelling is conducted to correlate post peak behavior of the rock mass with actual tunnel displacement."

Jan 1, 2015

By Jane Spooner

"The papers presented in this edition of the Bulletin cover some of the business issues that face mining companies exploring or operating in jurisdictions outside Canada. While technical innovations may, generally, be seen as fast-moving and farreaching, these papers also show that changes in approach and thinking continue to be evaluated and implemented.The Forum paper co-authored by Roger Taplin of McCarthy Tétrault LLP and Marchand Snyman of Muratie Investments Pty Ltd. highlights the quite radical changes that have taken place in South Africa’s mining industry with the introduction of the Mineral and Petroleum Resources Development Act, 2002, in October of that year, together with the Broad-based Socio-Economic Empowerment Charter for the South African Mining Industry and the Mineral and Petroleum Royalty Bill of March 2003."

Jan 1, 2004

What is the BC AMTA? ?What is an ASEP? ?Who are the partners? ?Critical Success Factors ?Questions/Answers Aboriginal Skills and Employment Program (ASEP) ?A collaborative partnership of industry, employers, post secondary, First Nations and government ?Working together to plan and implement training and education programs ?Demand-driven: targeted JOBS for participants

May 1, 2010

By J. E. Gill

"The Wasa Lake property is a block of about 1,640 acres in Beauchastel township, Quebec. Gold was discovered there first in 1936 in what is now known as the 'Southern area ( Fig. 1). Stripping and trenching were followed by 9,218 feet of diamond drilling in twenty holes. A number of good intersections were obtained, but their interpretation in terms of ore was difficult. A shaft was then sunk to 220 feet vertical depth. Thirteen hundred feet of lateral work and 543 feet of diamond drilling were completed at the 200-foot level before work was discontinued in 1938. Results up to this point had been just fair.Early in 1944, surface diamond drilling was resumed. The first hole cut material of ore grade in a strong shear zone 1,000 feet north of the old workings, and holes to the east and west showed this to be an extensive gold-bearing zone.In August 1945, a main working shaft was started. This has been sunk to 550 feet slope depth. A cross-cut at 390 feet vertical depth was driven to the ore zone and, by drifting and drilling at regular intervals, a length of 725 feet had been tested to December 31st, 1946 ( Figs. 1 and 2). The results check those from surface drilling quite closely.In the main zone, scoping widths from 8 to 40 feet and averaging about 25 feet are indicated. The grade after dilution should be about 0.15 oz. gold a ton and operation will probably start at 1,000 tons a day."

Jan 1, 1954

By Jason J. Crowder

Presentation Outline ? Introduction ? Costs of ground support and rehabilitation ? Why post-failure rock mass properties are necessary ? The Rock Mechanics Problem ? Present State of Modelling and Instrumentation in Mining ? Case Study Background ??Williams Mine ? Deriving Parameters for Modelling from Instrumentation ? Results from Case Study ??Back Analyses ? Discussion of Research Impact t Summary

May 1, 2006

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By H. A. Schnell

"The Phase I Mill at Cluff Lake in northern Saskatchewan was designed to accommodate a very specific high grade uranium ore. As this high grade ore was depleted, construction was undertaken on a new mill circuit (Phase 2) to process a more conventional lower grade ore deposit.The Phase 2 Mill expanded the ore throughput to 800 tonnes per day. The new process employs crushing, grinding, leaching, counter—current decantation, solvent extraction and magnesia yellowcake precipitation and drying to produce a yellowcake concentrate.This paper discusses the process decisions required for this expansion and outlines the new mill circuit. Included is a review of the start up in August, 1984.1.,INTRODUCTION The Cluff Lake Uranium deposit is located 720 kilometers north of Saskatoon in northern Saskatchewan. A high grade deposit was discovered in 1970 with the first production taking place in 1980 after lengthy hearings. The original mill (or Phase 1 Mill) was specifically designed to accommodate this very high grade ore for a very limited plant life.Pilot plant work was carried out in 1981 on the other lower grade ores found in the immediate Cluff Lake area. Feasibility and process selection studies were then undertaken as the Phase 1 mill was nearing its end of life. These studies were completed in March 1983 when approval was given to construct the new Phase 2 mill."

Jan 1, 1985

By Jürgen Antrekowitsch, Gerardo R. F. Alvear Flores, Mehmet Ayhan, Christoph Zschiesche

Synergies between copper and lead extractive metallurgical processes enable the processing of a broad range of polymetallic materials. However, this complexity also brings some challenges expressed in terms of complex intermediates and final products. For instance, based on the limited solubility of Cu and Ni in crude lead bullion additional phases will appear during the crystallization of the melt. Beyond the need for continuous optimization of metallurgy the control of phase solidification is a further important pillar to achieve a more efficient process by minimizing the amount and cycles of reverts. This paper describes the microscopy study of one of the most relevant intermediate in the Cu and Pb metallurgy, the Cu based alloy and highlights the importance of applying a well-controlled cooling sequence to improve the overall process efficiency. INTRODUCTION One of the key aspects in Aurubis’s 2025 vision is to move towards the implementation of a multi metal recovery strategy. The implementation of this new multi metal vision is supported by the long tradition of the company, founded in 1866 as Norddeutsche Affinerie, and further developed by adopting modern copper smelting and lead smelting technologies for the processing of primary and secondary materials. The combination of these assets have already build the basis for processing of complex materials in the copper and lead circuits implemented in Aurubis’s facilities. The addition of a new smelting facility, will enhance these capabilities. Aurubis current flowsheet combines Cu, Pb and Zn metallurgy. This includes primary smelting of copper concentrate, processing of secondaries (residues, slimes, slags) and recycling materials (scrap, shredder material, e-scrap). These broad range of materials contain not only the mentioned base metals but also a number of minor metals that requires to be properly managed to ensure efficient recoveries and quality of the targeted metals.

Jan 1, 2019

By C. Carlson, W. Muir

"The oxygen demand of the complex lead-zinc-iron feed at the Cyuro Anvil concentrator was determined denendent on the cyanide ion con-contration of the pulp. By redistribution of the cyanide [ ] the grinding circuit in direct proportion to the amount of surface area created, a more activated flotation feed in obtained.Monitoring the oxygen demand of the flotation feed and grinding mill discharge has proved useful in diagnosing metallurgical problems day to day operation."

Jan 1, 1976

By Don Thompson

It isn?t a lie if you don?t tell the whole truth The pictures National Geographic didn?t print Other photos National Geographic didn?t print?

May 1, 2009

By J. W. Merks

"Simulation is the process of designing a computerized model, of a system or procedure, for the purpose of understanding its behaviour and developing strategies to control its operation. Simulation models are rapidly becoming an effective tool for mineral processing plants. Powerful software and fast hardware are more readily available than a basic understanding of the theory of mathematical probability and applied statistics that process simulation models demand.Simple spreadsheet software can be used to develop simulation models that take into account any set of conditions at a mineral processing plant. In addition to an unbiased estimate for each variable in the set on which two-and three-product formulas are based, reliable variance estimates for all variables are required. How to estimate variances, effectively and at the lowest possible cost, and how to compute variances for simple functions such as the metal content of a quantity of ore or concentrate, or more complex functions such as the percentage recovery at a mineral processing plant, are the key to useful simulation models.IntroductionSimulation models for systems and procedures have become one of the most powerful and effective applications for computers( 2.6). Simulations are applied to a wide range of scientific and engineering disciplines. Generally, a model is designed to investigate the effects of changes in and interactions between a set of variables before a system is in operation or a procedure is implemented, by simulating weeks, months, and even years of operation, in a few minutes of computer time. Along with practical and useful applications always comeabuse and misuse. For a simulation process cannot be more reliable than the methodology that was applied to design the model, to estimate variables and variances, to check performance, and to verify validity. A mineral processing plant is a dynamic system that changes continuously as a function of time but within probabilistic constraints that can be estimated by applying statistical tools and techniques to the variables and variances that interact in the system.A model should be designed to simulate not only the set of variables but also the variance for each variable. Models in which constant variances are used to generate normally distributed random numbers, are less realistic than models in which the variances are simulated first, and then used to simulate the variables."

Jan 1, 1991

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the few years. Accidents rates are at a ?plateau? and yet, serious accidents and fatality rates are not. In more dramatic cases, such as in the BP Texas disaster, organizations that have ?exemplary? safety statistics, suddenly have a catastrophic or multi-fatality event occurring. Other classic examples are the Piper Alpha disaster and NASA?s Challenger and Columbia disasters and even the Chernobyl nuclear reactor. Looking into the root causes of these accidents provides an insight into the events and deficiencies that led up to the accident, but what are the common features in the organization?s mindset? What characterizes these organizations? decision making, their approach to safety and to risk and are there specific cultural features that can be delineated? The research and review presented in this paper covers a period since 1994, which started in the Australian resource industry and since then covered international events. The features of these organizations are summarized as the seven deadly delusions, based on extensive research since 1997 of organizations that suffered unexpected disasters. Their huge focus on safety, the achievement of lofty goals and celebration of safety successes led to ?mindset? that they are leaders in safety, protected by an extraordinary safety system and that their safety incident figures indicated a truly world-class safety performance. It led them into the trap of the seven deadly delusions?

May 1, 2011

By V. Cvetkovic, L. Zou, L. Jing

"Sorption process plays a significant role for solute retardation in rock fractures. In this paper, for the aim to investigate the effect of sorption on solute transport in a single rough fracture, a 2D model of representative single rock fracture was built and its roughness was statistically characterized based on the measured data of rock surface topography by laser scanning. A Finite Volume Method (FVM) code was developed to solve the Navier-Stokes (NS) equations and transport equation for numerical modelling the process of fluid flow and solute transport in the rock fracture model. Two groups of simulations were conducted: with and without the consideration of the sorption process with different average flow velocities. The results show that the surface roughness increased the complexities of flow fields, and the non-linear sorption process plays a significant role in the retardation of solute transport through rock fractures. The sorption process caused an obvious lagging time in both the solute concentration fields (plumes) and corresponding breakthrough curves. This lagging time increases with the distance from the inlet boundary, and relatively decreases with the increase of mean velocities. INTRODUCTIONFluid flow and solute transport in fractured rocks is an important research topic for performance and risk assessments for rock engineering projects concerning geo-environment safety, such as radioactive waste disposal, mining, geothermal extraction, reservoir engineering and other contaminant transport processes in geosphere (Berkowitz 2002).The solute transport in the rock fractures mainly involve the advection, surface sorption, matrix diffusion, dispersion, radioactive decay and chemical reactions, governed by general transport equations (e.g. Bodin et al., 2003). Among these transport phenomena, the sorption on the fracture walls can alter solute migration between the fractures, and play an important role in natural retention of solute transport (Weber et al., 1991; Wels et al., 1998; Kumar 2007; Dai et al., 2012). The aim of this study is to investigate the effect of sorption on the solute transport in a single rock fracture with rough surfaces. More complex transport processes, such as matrix diffusion, dispersions, radioactive decay and chemical reactions, are not included in this study."

Jan 1, 2015

By Pierre Pelletier, Julie Fournier, Gianni Bartolacci, Yves Breau, Dominique Girard, Ahmed Bouajila, Carl Duchesne

"The development of on-stream analyzers (OSA), such as those based on X-ray fluorescence (XRF), has been key to improve metallurgical performance of flotation processes. However, since these analyzers are shared between several streams, they typically provide grade measurements every about 10-15 minutes. In general, this frequency is too long compared to process dynamics and so, implementing an efficient feedback control strategy based on OSA can be difficult. In addition, due to the limited capacity of OSA systems, several important intermediate streams are not analysed, but could provide relevant information about the state of a flotation circuit.To overcome this problem, vision systems have been developed in the past to predict concentrate grade based on froth color – this could be very useful to control flotation performance between OSA measurements. However, applications reported in the literature typically use univariate summary statistics of the full red, blue, and green color distribution of froth images, while RGB images are truly multivariate. Although, in some cases, grade prediction was achieved with reasonable accuracy, one may, by using only summary statistics, miss important information about the state of the flotation process.This paper investigates the application of Multivariate Image Analysis (MIA) concepts to flotation froth images. These techniques are based on multivariate statistical methods such as PCA and PLS, which have the ability to analyze large databases (such as digital images) and summarize the relevant information content of the data into a small number of latent variables, capturing the most important features of the images for concentrate grade prediction. The potential of application of these methods in the mineral processing industry is illustrated using a few industrial case studies."

Jan 1, 2003

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987