Search Documents

By John T. Ling

"This paper describes the operation of a rope haulage used as the main system of transportation in an underground coal mine. Prince Colliery, which is operated by the Cape Breton Development Corporation, has been in operation for 23 years and produces 1.2 million tonnes of coal annually. The mine extends a distance of 8000 metres under the Atlantic Ocean. All personnel and supplies are transported by means of an endless rope haulage system consisting of a train of rail cars that are operated by an electric engine on surface. The wire rope is 15 km long and weighs 63 tonnes. The system is believed to be the longest of its type used in an underground coal mine. The design of the system, safety features of the haulage, and problems encountered during the design and construction are described. IntroductionCoal has been mined commercially in Cape Breton, Nova Scotia since the 1800s. Several coal seams that are part of the Sydney coal fields, dip toward the north and northeast out under the Atlantic Ocean at angles between -4 and -15 degrees. Coal has been economically mined at depth in excess of 1200 m and more than 11 km from the coastline.Traditionally, single and double drum hoists have been used to haul the coal to the surface and also for transporting the workers and the materials required for mining up to 8 km. With the introduction of mechanized mining methods in the late 1960s, conveyor belts began to replace rope hoists for coal transportation. Improvements in hoisting system design also allowed for drums that could wind up to 6100 m of 32 mm wire rope in 15 layers.These hoists are commonly referred to as “drop hoists” because they take advantage of the gradient of the slope to assist in allowing the mine car train to reach the end of travel. The cars travel on steel rails and the rope is guided by rollers to reduce friction in the system."

Jan 1, 1999

By Jacek Paraszczak

As the deposits located closer to the surface are getting depleted, more and more Canadian mines produce ore from considerable depths. Deep mining represents a number of serious challenges including high rock temperature. Conventional diesel powered loadhaul- dump machines and trucks so widely used in metal mines constitute an additional source of heat and noxious gases. Due to this, they have a substantial adverse impact on a quantity of fresh air required and a cost of ventilation, particularly since the mines have to meet more and more stringent regulations in this respect. In this context, the paper examines possible alternatives for diesel powered equipment, both these commercially available as those at the stages of prototypes or under development. They are reviewed with regards to their principles, required infrastructure, stage of technology development and its progress. The questions of their flexibility, practicality and economic viability are also addressed. Following the above a potential for their implementation and possible benefits (if any) in the conditions of deep Canadian mines is discussed. The paper concludes with short to medium term predictions concerning the most promising drive alternatives for vehicles destined to operate in deep metal mines.

Feb 1, 2008

By D. M. Doyle

A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc., over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study progresses through monthly, daily and, finally, into quarter hourly data, the variations become more evident and, most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines Limited are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program. The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Limited's Sudbury operations, the metering and control equipment, the commitment, the new energy accounting practices and, lastly, the policies. Examples of successful energy conservation endeavours include automatic peak electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailment of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and, if necessary, immediate reporting of energy and energy per unit of production information The program so reported at Falconbridge's Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0-million-dollar annual energy account

Jan 1, 1979

By Robert B. Parsons

"It is generally acknowledged that Canadian and foreign-based mining companies are spending relatively fewer dollars in Canada and more dollars abroad than was the case not many years ago. It is common to see the Canadian tax system being fingered as one of the causes in this shift in direction. However, if one takes the time to peel away the surface of our tax system, and to probe a little deeper into its substance, it will be found that the Canadian taxation of mining is generally quite competitive. IntroductionCross-border shopping in the mining industry? - Absolutely! Economics 100 teaches that dollars are votes in the capitalist system, and mining companies are going to cast their limited number of votes where they can achieve the highest return at the least risk. The Canadian consumer knows that taxes are a major factor in cross-border shopping, and mining company executives know that the same tenet holds true in their industry. Unfortunately, mining operations are subject to such a bewildering array of tax rules that making an intelligent decision is not always an easy matter.Statutory Tax RatesConsider, for example, the ""statutory"" tax rates shown in Table 1. (Statutory tax rate in this table refers to the simple sum of federal and provincial tax rates on profits as specified in the tax legislation.) Looking only at the total statutory tax rates (such as 66070 for Manitoba) , one might quickly observe that the Canadian mining industry is subject to a truly onerous tax regime, especially as compared to the United States where statutory tax rates can be in the 34% range."

Jan 1, 1992

By Patricia Dillon

EHS Management Standards Communication and Reporting (8) ! Establish processes for internal and external communications ! Designate responsibilities for communication with COI ! Report as defined by senior management ! Report annually to employees, shareholders, COI on EHS and social performance Community Rights and Public Consultation (9) !Identify COI?s and establish process to hear concerns !Acknowledge and respond to complaints !Support local communities !Plan for closure and conduct public consultation !New projects include identification of COI?s, concerns to be considered in design

May 1, 2004

By Roger Davieds

FACT: a company?s profitability (or loss) is directly related to the efficiency and effectiveness of its maintenance operation. Fact: in order to contribute in a positive manner, maintenance must understand what its true purpose is in the organization. It is easy to say our main purpose is to increase: ?equipment uptime ?OEE ?asset life cycle We all understand this; so does management.

May 1, 2010

By J. Z. Cui

In this paper a statistical multi-scale method for the mechanics parameter prediction of the rock mass with random distribution of multi-scale cracks/joints is presented. First the micro-structure of the rock mass with random distribution of multi-scale cracks/joints is represented. Then the statistical second-order two-scale method for the mechanics performance predictions of the rock mass structure with random cracks/joints distribution is presented, including the statistical second-order two-scale expression on the vector-valued displacement, strain tensor and stress tensor, and the algorithm procedure of statistical multi-sale computation for the mechanics parameters. Finally some numerical results for mechanical parameters for the rock mass with random distributions of multi-scale joints/cracks by statistical multi-scale method are shown.

May 1, 2009

By K. Lambrych

Hydrometallurgical equipment used to extract and refine copper and other metals is exposed to extremely corrosive chemical environments. These systems must be fabricated from materials that are durable against corrosion, meet exacting mechanical requirements, and perform economically over the life of the mineral processing plant. In several recent large hydromet projects, fiber reinforced plastic (FRP) has been shown to provide equal if not superior durability relative to alternative materials of construction. This paper will compare corrosion performance and cost of plant equipment fabricated with corrosion resistant alloys, rubber lined steel, and FRP made with Epoxy Vinyl Ester thermoset resins. Case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory-based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment. Specific examples from projects such as El Boleo, Long Harbour and others will be used to demonstrate how the versatility of FRP allows for remote fabrication of durable corrosion-resistant large-scale equipment for hydrometallurgical refinement of copper and other metals. INTRODUCTION Fiber reinforced plastic (FRP) began to emerge as a material of construction for corrosion service in many industrial processes in the late 1950s because of its ease of use and overall performance. Corrosion resistant (CR) FRP, as an alternative construction material to alloys, rubber and tile linings, grew steadily in following decades. The aggressive operating conditions associated with hydrometallurgical processes typically require materials of construction that can withstand acids and acid chlorides at temperatures up to 90°C, sometimes higher. Common metallic materials of construction, such as carbon steel, are not compatible with these conditions. High nickel alloys are capable of meeting performance requirements, but often at a high cost. In many cases FRP mining equipment based on epoxy vinyl ester resin (EVER) offers durability, long service life and lower maintenance costs. Through demonstrated performance and decades of case histories, more and more design engineers are confidently specifying FRP as the material of construction for new mineral processing equipment.

Jan 1, 2019

By Emilie Williams

Introduction Mouska Mine, Doyon Division site Background and timeline Obstacles to standard paste delivery system Components of Mouska paste system Technical considerations Operational considerations Mouska Mine Underground gold mine 30 km east of Rouyn-Noranda, Quebec Part of Doyon Division, 100% owned by IAMGold Commercial production since 1991 Cumulative production over 850,000 oz Conventional mining until 2009 485 m shaft from surface 560 m internal shaft 500 tpd (ore and waste) Off-site milling Approximately 150 employees

Oct 1, 2010

By D. C. Martin, P. M. Hawley, C. P. Acott

"In bedded deposits such as coal or sedimentary iron, economic limits of mineable reserves are clearly defined by the footwall of the seams or ore-bearing units. Where open pits are developed in dipping strata, a long, high footwall slope may result. In many cases, unbenched slopes excavated along the base of the lowest mineable seam are operationally simple, economically desirable and geotechnicalty practical, although a variety of failure mechanisms may develop. This paper examines the engineering geology and rock mechanics parameters of importance in the design of footwall slopes. Possible failure mechanisms and stability analysis methods are described. Design considerations for benched and unbenched slopes are discussed with prime consideration given to development of long high stopes without benches or with a minimum number of benches. IntroductionIn bedded deposits, the ultimate depth and economic viability of an open pit in dipping strata may be controlled by the design of the footwall slope. The stability and, hence, design of footwall slopes is strongly influenced by the engineering geology and rock mechanics parameters of the slope forming materials. A clear understanding of the structural geology, engineering geology and tectonic history of the deposit is essential to assess the behaviour of the slope. This is particularly important for long high, unbenched footwall slopes such as shown in Photo I.A rational footwall slope design requires identification and assessment of all possible slope failure mechanisms with respect to the proposed slope geometry. Stability analyses of each potential failure mechanism are used to identify the main controls on slope stability and to develop appropriate slope design criteria. The optimum slope design is based on the most economic and geotechnically practical slope geometry with due consideration of operational constraints and of the possible advantages of specific remedial measures."

Jan 1, 1986

Proper water and thermal management is essential for obtaining high performance of Proton Exchange Membrane Fuel Cells (PEMFCs). A steady, two-dimensional water and thermal management model was developed, aiming at considering pressure drop, open circuit voltage variation with stack temperature, water vapor effects on membrane conductivity, which made the model physically more reasonable and more suitable for various operating conditions. The model could predict the distributions of a series of important parameters along the flow channel, and thus the effects of various operating and design parameters on the fuel cell performance could be investigated easily by numerical trial-and-error method. The modeling results compared well with the available experimental results from the literatures. The results also showed that the humidification is crucial for the performance of PEMFCs. The model could be a very useful engineering tool for the optimization of PEMFCs.

Jan 1, 2005

By J. Sammut, T. G. Joseph, R. Andreev, M. Curley

"Decisions regarding mining method and subsequent choice of excavator must take into account the quantitative factors of productivity, availability, and capital, operating, and maintenance costs. Dig performance was compared between a hydraulic excavator (HE) and electric rope shovel (RS) of similar size class (i.e., use the same amount of energy to excavate a unit quantity of the same material from a mining face), focusing on the quantitative factors above. Machine performance, normalized to bucket capacity, was assessed as a function of hours of service (60,000 hours per machine). Results showed higher production rates for the HE of similar capacity and age. In general, the RS exhibited lower service cost per volume capacity, though it had higher capital cost. The RS became more cost effective than the HE of similar capacity within approximately 30,000 hours of service. ¦ KEYWORDS Cost, Electric rope shovel (RS), Excavation, Hydraulic excavator (HE), Surface mining RÉSUMÉ Les décisions concernant la méthode minière à adopter et le choix ultérieur d’un engin d’ex¬cavation doivent tenir compte des facteurs quantitatifs de la productivité, de la disponibilité ainsi que des coûts d’investissement, d’exploitation et d’entretien. Cette étude compare les performances en termes d’excavation d’une excavatrice hydraulique et d’une pelle électrique à câbles de même taille (qui utili¬sent par exemple la même quantité d’énergie pour creuser une quantité unitaire du même matériau dans un front de taille), en se concentrant sur les facteurs quantitatifs susmentionnés. La performance de la machine, normalisée à la contenance du godet de volume unitaire, est évaluée en fonction des heures de service (60 000 heures d’activité par machine). Les résultats montrent des taux de production plus élevés pour l’excavatrice hydraulique d’une capacité et d’une ancienneté similaires. De manière générale, la pelle électrique à câbles affiche un coût d’entretien par capacité volumique inférieur, mais son coût d’in¬vestissement est plus élevé. La pelle électrique à câbles devient plus rentable que l’excavatrice hydrau¬lique d’une même capacité au bout d’environ 30 000 heures de fonctionnement. ¦ MOTS CLÉS coût, excavation, excavatrice hydraulique, exploitation à ciel ouvert, pelle électrique à cablesINTRODUCTION The most common excavating tools in surface mining operations are the hydraulic excavator (HE) and electric rope shovel (RS). In general, electric RSs are more reliable and cheaper to maintain (P&H Mining Equipment, 2007), but where complicated geological conditions exist, HEs are preferred because they are generally considered to be more mobile."

Jan 1, 2019

By G. A. Gross

DURING the past 5 years a large amount of money and effort has been expended in exploration of iron-formations and in testing their suitability for beneficiation. Beds of ferruginous material are numerous and widely distributed in the Precambrian rocks of Canada and practically all of the known iron ranges or belts have been examined to a limited degree at least in an effort to evaluate their potential as sources of iron ore. A number of favorable beds have been selected for mining on completion of surface sampling, diamond drilling, extensive metallurgical testing and economic studies, and many other ranges are being studied. There are still a great many iron-formations that have not been evaluated by modern concentration methods and their regional extent is not fully known. The iron-formations are easily located by airborne or ground magnetic surveys but the main task in finding a mineable ore-body of this type amounts to locating a bed sufficiently large for mining which consists of material that can be concentrated economically by modern beneficiating methods. The ease with which an iron-formation can be concentrated to give a marketable ore depends primarily

Jan 1, 1961

By M. Redfearn

"DUST COLLECTION EQUIPMENT LIST Primary Dust CollectorModular Mikro-Pulsaire - Model 2G1-96TR Capacity: 20,000 c.f.m.Bags: Total of 288; 8' x 4 1/2"" diameterMaterial: Dacron HCE feltAir to cloth ratio: 7.55/1Bags are changed every 6-9 months. Sent to A & L Services for cleaning at a cost of less than 1/3 the price of a new bag. No new bags have been required since start-up 4 years ago.Blow hack: 35 c.f.m. at 100 p.s.i.Fan: Joy Manufacturing, Model 3300, Type 4S, Backward inclined fan.Impeller: 33"" diameter36"" diameter Inlet33"" diameter Outlet at 3200 f.p.m. velocity1945Motor:,60 H.P., 1780 r.p.m.Capacity: 23,400 c.f.m.Design:,20,000 c.f.m.,•Actual:,17,500-19,000 c.f.m. depending on bag condition.Dust Slurry Agitator: Port-a-flo Model 050-350Major Maintenance:The fan was sped up from 1830 to 1945 r.p.m. and balanced at the higher speed. Several months later the impeller destructed beyond repair. A new shaft and impeller was installed, casings straightened, and bearings reused. Unit is currently running at 1945 r.p.m. No definite cause for the impeller failure has been found, although it might be attributed to improper balancing."

Jan 1, 1976

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

Today?s Topics ? Data to decision value chain ? Practical Considerations ? Example ? Before / After DSS ? Quick Decision Support Demo Practical Considerations ? More data is not necessarily better ? Organization and process silos ? Good vs. ?optimal?, but impractical Solutions

May 1, 2008

By Robert B. Parsons

"Income tax legislation is not keeping pace with federal and provincial environmental legislation. There is a vast array of new environmental regulations at various stages of implementation across the country. Unfortunately, there are serious concerns about the deductibility of significant payments which mining companies will be required to make under these new rules, and the Department of Finance seems to be reluctant to act on these concerns. IntroductionWhile the federal and provincial governments are racing ahead with obvious fervour to introduce new envirorunental laws, the tax rules relating to envirorunental costs are being allowed to lag far behind. In a nutshell, the tax treatment of envirorunental costs is not keeping pace with the new envirorunental legislation.One of the most serious concerns of the mining industry is the deductibility of mine reclamation or closing costs. The producing provinces are well advanced down the road toward mandating upfront deposits, bonds, or similar financial guarantees to protect the envirorunent from the operation and eventual closure of a mine. These requirements are not small. In some instances, they can amount to tens of millions of dollars. And, if there is no tax deduction for these sums when they are set aside by the mining company, then the costs have to be paid out of the company's after-tax earnings."

Jan 1, 1991

By Jason Prno

Context ? Climate change an issue of global significance ? Research is lacking ? Study initiated by the David Suzuki Foundation, led by ArcticNorth Consulting Industry Surveying ? 34% and 48% of respondents indicated climate change is already affecting operations ? Majority believed climate change would have negative impacts in the future ? Cost and uncertainty of Future impacts are major barriers to adaptation

May 1, 2010

By Raynald Vézina, Richard Leclerc, Jean Boissonnault, Louis P. Gignac, Gérald Veillette

Since mid-1989, Cambior has increased its producing gold mines from four to six, having acquired the Chima Mine and brought the Silidor Mine onstream. In June 1990, the company announced that the Mouska project would also be put into production. Gold production reached almost 190 000 ounces in 1989 and is expected to exceed 220 000 ounces this year. Cambior has also a non-gold operation with an interest of 50% in the Niobec Mine and has recently signed an option agreement in the development of the Lac Knife graphite deposit in northeastern Quebec. During the past year, the company has extended its exploration activities to the United States and Indonesia, and now has interests in nearly 80 properties. Last May, Cambior signed an option agreement with Golden Star for a gold deposit in Guyana, the OMAI Project, containing at least 2 000 000 ounces of gold in situ.

Jan 1, 1990

By H. D. Stolovitch, M. L. Lavallée

"An engineering system used to analyze and improve the performance of industrial grinding circuits has been adapted into a training program. The systematic approach to the design of training was applied in order to:Determine if training was an appropriate and effective tool for the transfer of this new technology;Define the technical content of the program;Establish program specifications based on learner and context characteristics;Design and test prototypes of the instructional modules; and,Establish a strategy for plant implementation and maintenance of the training program.This paper thus describes how a engineering system is transferred to the workplace through the use of designed instruction.INTRODUCTIONTraining can change human performance in a permanent way. It can improve productivity for the overall benefit of an operation. Organizations can therefore use training as a mean to achieve their specific goals. Training is not the solution to every performance problem. However, in many cases, it can be a very effective way to attain desired performance.The benefits of training are often difficult to assess. However, to remain competitive, organizations must introduce new products and innovative technologies. Often, they can do both most effectively through suitable training interventions.In order for the effort and investment of training to provide optimal results, two points of view should be adopted.• An overall view of the system in which training is to be applied.• A systematic approach to the design of training (Stolovitch and Keeps, 1989)."

Jan 1, 1992