Search Documents

By Alan L. Sangster

Auriferous, bedding-parallel veins occur in zones of carbonaceous, argillaceous and sulfidic turbidites in the Lower to Middle Cambrian sandy flysch of the Goldenville Formation. The 0348 values for vein and wall-rock arsenopyrite and pyrrhotite, and for regional pyrite and pyrrhotite, are highly positive. The values are similar to those from Cambro-Ordovician sediment-hosted deposits of other types, and display trends that increase upward in the stratigraphic sequence. The similarity in composition of vein and wallrock sulfides indicates a seawater-sulfate sourCe for sulfur, derived from the enclosing rocks at the time of vein formation. The upward increase in ?34S values is consistent with closed system sulfate reduction in the anoxic portion of a stratified water-colurnn. Published ? 13C and ? 18() values for Meguma Group vein carbonates are unlike those of other gold-vein carbonates, but are similar to those of diagenetic-metamorphic carbonates from the Meguma Group and elsewhere. These data indicate that the source for the vein-related sulfides and carbonates may be the host strata; possibly the arsenic and gold were derived from the same source.

Jan 1, 1992

A key point in the manufacture of cemented backfill is the dewatering and settlement of the total tailings product. A new technology characterized by rapid non-mechanical settlement of total tailings has been developed based on a large number of laboratory and field tests, where dynamic settlement and continual slurry preparation of total tailings in a vertical sand silo are realized by the addition of an effective flocculating agent named NPA. It has been shown that the sedimentation velocity of the interface between total tailings and water after NPA was added is 10 to 20 times higher than that without any flocculating agent, that the mass fraction of sand slurry deposited at the bottom of the vertical sand silo reaches 70%, and that the solid particle content in effluent waste water meets national water quality standards. The simple devices used to add flocculants have little deleterious effects on the current preparation tank and have been tested in an industrial environment. The processing cost of total tailings by the new technology is only 10% to 20% of that required for mechanical settlement.

May 1, 2007

By Fathi Habashi

This Historical Metallurgy Note is the final part of a three-part series, the first two of which appeared in the November- December, 1997 and January, 1998 issues of the Bulletin. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940- 1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of the Institute.

Feb 1, 1998

By Roy O. Ifill, W. Charle Cooper, Alan H. Clark

"Queen’s UniversityIn representative, run-of-mine samples from the Panel and New Quirke mines of the Elliot Lake uranium district, Ontario, brannerite, ametamict uranous titanate, occurs in microscopic grain-aggregates which display wide variations, both in textural habit and in the relative proportions of brannerite, titania polymorphs and/or “uraniferous titania”. As is widely documented, much of the brannerite occurs as trellis-like arrays of laths and needles pseudomorphing rutile oranatase. In some cases, the laths and needles are cemented by coffinite. Brannerite, with an average composition of (U0.629Th0.039Ca0.20)(Ti2.199Fe0.13)O69contains =3 wt% Th and is distinctly Ti-rich relative to the ideal composition, UTi2O6. Much of the Si reporting consistently in electron microprobe analyses (between 1 wt%and 5 wt%) is tentatively attributed to contamination by the quartz-sericite matrix, and a minor proportion is attributed to the presence of coffinite intergrowths. “Uraniferous titania” (average par-tial composition by weight: 10.8% U, 0.3% Th,32.9% Ti) is considered to represent an intermediate stage in the conversion of titania to brannerite.The leaching behaviour of brannerite in its different modes of occurrence was studied qualitatively by the rotating-disc (polished section) method in H2SO4and HCl solutions at 25° to70°C. Redox potential was not measured. The progress of the dissolution of the individual brannerite crystallites and grain-aggregates was monitored by optical and scanning electron microscopes. Regardless of its morphology and texture (laths or needles, reticulate or blocky),brannerite is not readily leachable. Regardless of the process conditions, the rate-controlling step appears to be the initial leach-pit formation. These pits expand radially through the aggregate as leaching proceeds. This dissolution mode is independent of the relative amounts of brannerite and titania, i.e. the type of grain-aggregate. Secondary coffinite intergrowths are readily leachable and enhance the overall leaching kinetics of brannerite by accelerating leach-pit formation. These data provide, for the first time, information on the controls on the leaching of the uraniferous phases which dominate the lower-grade ores in the Elliot Lake district."

Jan 1, 1996

By Fathi Habashi

This Historical Metallurgy Note is the second part of a three-part series, the first of which appeared in the November- December issue of the Bulletin. Part III will be published in February, 1998. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940-1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of his Institute.

Jan 1, 1998

By C. Greimel

Modern roadheaders provide a safe and cost-effective, yet very flexible way of mechanical tunnel and roadway excavation. In the last years, SANDVIK Mining and Construction has developed a NEW ROADHEADER GENERATION, which incorporates new features, allowing significant improvements of underground excavation. Partial face cutting machines such as roadheaders excavate the desired profile by means of a cutter unit mounted on a swiveling boom. This flexible method for mechanical excavation makes the roadheader suitable for a large range of profile varieties and most rock characteristics. Over 1,250 roadheaders have been delivered since the 1960s from the Zeltweg plant of Sandvik Mining and Construction, with the current products ranging from the light-duty, 130kW MR220 machine, widely used in the tunneling and coal industry to the heaviest 300kW tunneling and hardrock mining roadheaders. Roadheaders are generally used in coal mine development, salt/potash mining as well as construction and hard rock mining. This paper describes the technology behind the succesful introduction of hard rock cutting with roadheaders, and aims to offer best practise operation experiences from various hard rock cutting sites.

Oct 1, 2010

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China. The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture rone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrurn in stage I and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to rone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994

By Natasha A. Essar

Nevsun Resources Ltd. Bisha Mine Project is a gold and base metal development project in the Gash Barka region of west-central Eritrea. The project has the potential to be one of the largest industrial developments in the country, and Eritreans have no experience in modern mining. Nevsun recognized early that the success of the Bisha Project would require meaningful consultation and engagement with all levels of Eritrean society. Meaningful engagement required not only full disclosure, but also capacity building from government officials at all levels to other stakeholders who live in the nearby communities. This paper describes the approach used to develop capacity and to help introduce a modern mining culture in a country without previous experience in mining.

May 1, 2007

By R. Biss

"Niobium or columbium, as usually called in North America is becoming a more and more important metal in the industrial world because of its attractive properties.Eventhough discovered in the early nineteenth century, it was not until the 1930's that its use became more widespread. The discovery of large commercial deposits in the late 1950's and the demand of industry for steel with high strength and toughness further promoted its use. To assure its adequate supply new or-e processinr technologies had to be developed. So, beside the traditional gravity concentration, the flotation process was employed for the partial upgrading of pyrochlore concentrate at S8ve (Norway) plant in 1953. The flotation process was equally used at St-Lawrence Columbium plant in the province of Quebec, Canada. The new plants at Araxa and Catalao in Brazil and at St-Honore, Canada, which supply almost of all niobium used today in the non-Communist world, also adopted the flotation process. The processes using long chain aliphatic rnonoarnines, diamines or sulfonates as collectors proved to be difficult especially on weathered types of ores or on those having a substantial content of silicate gangue minerals. They almost completely failed in case of alkaline intrusive rocks as syenites, nepheline syenite, ijolites and pyroxenites, composed almost entirely of silicate minerals. A lot of effort was devoted all around the world on research of new, more efficient flotation processes. So in 1982, Les Services T.M.G. Inc. (Niobec), sole producer of pyrochlore concentrate in North America, developed the direct pyrochlore flotation process from carbonatites. In 1983, at about the same time, the Quebec Department of Natural Resources Laboratories and Les Services T.M.G. Inc. announced a successful recovery of niobium Minera1s from a low grade nenheline syenite ore."

Jan 1, 1984

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980

By R. V. Kumar, F. Tailoka

In order to use ZnO laden dust as a possible desulphurization reagent, it is important to evaluate thermodynamics of the Zn-O-S system. At temperatures greater than 1450 K, there is an uncertainty in the thermodynamic data for the reaction of zinc with sulfur to form Zinc sulfide. In this work, the standard free energy has been determined using an electrochemical cell: Pt, Mo, MoO2/YSZ/ZnO, ZnS, S02, Pt., between 1198 and 1602 K. AG° varies from -145,880 to -88,100 J (± 2500) , with a phase change to ZnS (g) by sublimation occurring between 1450 and 1460 K. This is supported by thermogravimetric analysis which shows about 80% weight loss in ZnS from 1273 to 1473 K. Feasibility reactions were also performed and confirmed that ZnS (g) is formed when ZnO reacts with FeS (1473 to 1653 K) or with Fe-Csat-S(1473-1673 K). There is therefore potential for the utilization of ZnO laden waste as an additional or alternative reagent for desulfurisation.

Jan 1, 2004

By G. Ladouceur

"LOCATIONThe mine and mill are located in Lemoine township which is 20 miles directly south-east of the town of Chibougamau Quebec. Personnel live in Chibougamau and commute to the property over 33 miles of paved and gravel roads. Concentrates are trucked 13 miles to a railway siding on the line connecting Chibougamau and Quebec city.HISTORY Several companies explored the property before acquisition by Patino Mines (Quebec) Limited in 1973. Further exploration led to the discovery of a high grade copper-zinc orebody and the property was brought into production by the above company in 1976.ORE The ore contains 85% - 95% sulphides consisting of chalcopyrite, sphalerite, pyrite, pyrrhotite and minor gold and silver. Argenti tetrahedrite, antimonial silver, native bismuth and galena are also pre sent in very minor quantities. Associated gangue minerals are quartz, carbonates and occasionally chlorite."

Jan 1, 1979

By M. F. Gallerneault, V. Fallah, A. Howells, W. M. T. Gallerneault

"The occurrence of recrystallization in cold-worked aluminum sheet during the brazing process leads to loss of strength, an inhomogeneous grain structure and reduced corrosion resistance. AlMgScZr alloys are known for their extraordinary recrystallization resistance due to the influence of Sc and Zr addition on their microstructure. Here, we investigate the effect of alloy composition (i.e. Mn, Mg, Sc, Zr content), cold-roll reduction and pre-aging treatment on the recrystallization behavior of cold-rolled sheets at brazing temperatures typically used during the manufacture of heat exchanger units. The analysis of recrystallization behavior is carried out through microstructural characterization and the results are compared with the behavior of a commercial, AA3xxx-based heat exchanger alloy.INTRODUCTION Control of recrystallization is of critical importance during brazing, which is a widely-used joining technique for aluminum alloys in aircraft structures (Heinz, 2000) and automotive heat exchangers (Miller, 2000; Marshall, 1993). Due to excessive local heat at brazing temperatures, the cold work texture of aluminum alloys in the cold-rolled sheets may undergo a local recrystallization process (Marshall, 1993). This leads to the formation of an inhomogeneous microstructure and thus anisotropic mechanical properties (Miller, 2000) and low corrosion resistance (Marshall, 1993) across the sheet. X800, a commonly-used Al-Mn alloy series for automotive heat exchangers applications, has been developed specifically for a higher strength as well as an enhanced corrosion resistance as opposed to the traditionally-used AA3003 alloy (Marshall, 1993). X800 alloys, however, exhibit a low recrystallization resistance at normal brazing temperatures, i.e. 590°C. In contrast, Al-Sc-Zr alloys have been shown to exhibit an extraordinary recrystallization resistance at such temperatures (Riddle, 2004) while also being corrosion resistant and possessing a high room-temperature strength (Fuller, 2002). This has been shown to be due to the formation of coherent, nanoscale Al3(ScZr) precipitates that effectively impede grain boundaries while also exhibiting very slow coarsening kinetics at high temperatures (Riddle, 2004; Jones, 2003; Ocenasek, 2001). In this study, we analyze the recrystallization behavior of X800 alloys under brazing conditions through introducing Sc and Zr into the system as well as varying the Mn and Mg content. The effect of processing route is also studied by introducing a pre-aging stabilization treatment as well as varying the cold-roll reduction prior to the final brazing anneal."

Jan 1, 2018

By L. Voisin, K. Itagaki

In the reductive smelting of the copper concentrate like a blast furnace operation using coke as fuel and reductant or in processing the copper concentrate which contains coal in the bulk, a sulfur-deficient matte phase often coexists with an iron base alloy in the bottom of the smelting furnace. This alloy is generally called furnace residue or speiss when considerable amount of arsenic or antimony is contained in the alloy and in the extreme case of reducing condition the alloy is saturated with carbon. As a fundamental study to know the behavior of some precious metals such as silver, gold and platinum between the sulfur-deficient matte and the furnace residue or the speiss which are in equilibrium under reducing condition, the phase relations and distribution of precious elements in the Cu-Fe-S-As and Cu-Fe-S-Sb systems saturated with carbon were determined at 1473 K by a quenching method.

Jan 1, 2007

By H. Warren Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomic. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

May 1, 2002

By Jiwen Zhang

Abstract Due to the blocking nature at the crusher station, straightforward application of queuing theory cannot give realistic results on the performance of a shovel-truck-crusher system. A new queuing network-based model has been developed in which, the crusher station is formulated into an open queuing network and the whole shovel-truck-crusher system into a closed queuing network with the crusher station as a special server. To fully account for the influence of blocking, Monte Carlo simulation is first used to obtain the performance parameters of the open queuing network for the crusher station. The closed queuing network for the entire system is solved by applying the Extended Summation Method (ESUM), in which the crusher server is described by the simulation results. The model has been applied to the Yuanbaoshan open-pit coal mine to analyze its shovel-truck-crusher system and to improve its efficiency. Results indicate that the blocking at the crusher is an important factor affecting the crusher output and in turn the efficiency of the whole system, and prove that the model can realistically describe the behavior of such systems.

Oct 1, 2009

By Jiwen Zhang

Due to the blocking nature at the crusher station, straightforward application of queuing theory cannot give realistic results on the performance of a shovel-truck-crusher system. A new queuing network-based model has been developed in which, the crusher station is formulated into an open queuing network and the whole shovel-truck-crusher system into a closed queuing network with the crusher station as a special server. To fully account for the influence of blocking, Monte Carlo simulation is first used to obtain the performance parameters of the open queuing network for the crusher station. The closed queuing network for the entire system is solved by applying the Extended Summation Method (ESUM), in which the crusher server is described by the simulation results. The model has been applied to the Yuanbaoshan open-pit coal mine to analyze its shovel-truck-crusher system and to improve its efficiency. Results indicate that the blocking at the crusher is an important factor affecting the crusher output and in turn the efficiency of the whole system, and prove that the model can realistically describe the behavior of such systems.

Oct 1, 2009

By E. W. Thorton

"This paper is intended to show that grinding media can effect flotation results, and in some instances the results are vastly different. I do not suggest that autogenous grinding is beneficial in the separation of all complex base metal ores, in fact I know of a case where autogenous grinding would be disastrous to any selective flotation. I do however contend that prospective flow sheets and reagent balances of any complex base metal ores should be tried with both types of grinding. I feel fortunate that the paper to be presented later in this meeting by Rene Klymouski will, I think, compliment and perhaps explain some of the results of my research.This paper will be in four parts. The first part deals with a literature survey on the subject. Surprisingly enough, very little information has been printed on the subject. The second part deals with results obtained in bench scale tests on an ore from Chester Mines Limited. It was in these tests that we realized that steel grinding was giving us serious problems. So bench scale tests are shown giving results with a stainless steel grind, a mild steel grind and a grind in a ceramic mill with ceramic billets.The third part of the paper deals with results obtained in the Mines Branch Pilot Plant, when again we ground the ore with three different types of grinding media. Incidentally, this has been the only pilot plant test made at the Mines Branch in which flotation products were made on both steel grinding and autogenous grinding on the same ore. The fourth part deals with two other New Brunswick ores and is intended to show that changing the grinding media effects ores other than that of Chester Mines Limited."

Jan 1, 1973

By H. P. Kang, Y. J. Feng

The hard roof in underground coal mines is generally considered as a main cause that induces disasters in working faces and entries, such as rock burst and windblast. Hydraulic fracturing technology is an effective approach to weaken hard roof to reduce ground pressure and control rock burst. The state and achievements associated with hydraulic fracturing technology applied in Chinese coal mines are summarized in this paper. Theories related to hydraulic fracturing are of the essence in fracture design to determine the fracture initiation and propagation pressure and predict the geometry and the characteristics of hydraulically induced fractures. Initially, theory of elasticity was employed to determine the breakdown pressure for a vertical borehole where the rock medium is assumed to be elastic. However, porosity and pore fluid have an influence on the borehole breakdown pressure, and then the poroelasticity theory was applied. Arbitrary deviated boreholes in practice are rather common and the maximum tensile stress criterion was employed to determine borehole breakdown pressure. The effect of natural crack in the rock medium on the initiation pressure has been taken into consideration through fracture mechanics. Meanwhile, considerable achievements have been made on hydraulic fracturing tools and equipment, and a set of mature hydraulic fracturing technologies for hard roof control are available. Some comprehensive investigations on the hydraulic fracturing for hard roof weakening are presented, and successful field applications in the Jincheng and Luan coal mining districts are introduced. Finally, the unsolved problems related to hydraulic fracturing are also put forward.

Jan 1, 2015

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016