Search Documents

By B. T. Lu, J. L. Luo, T. Yu, C. W. Chen

In this paper, the synergism in erosion-corrosion process occurring in oil sand wastewater transportation caused by the interaction of mechanical and electrochemical factors was experimentally investigated. The erosion-corrosion tests were conducted with A1045 steel in synthetic slurries comprising tap water and silica sand. The material loss due to corrosion-enhanced erosion was assessed with the chemo-mechanical model developed by the authors recently. The results indicate that the material loss produced by corrosion-enhanced erosion at the open circuit potential can be formulated as a linear function of logarithm of corrosion current density. The wastage caused by the erosion-enhanced corrosion was analyzed based on the concept of non-equilibrium thermodynamics. The material loss induced by the erosion-enhanced corrosion is approximately a linear function of overall erosion rate measured in synthetic slurries, indicating that erosion-enhanced corrosion could be reduced by adopting surface strengthening techniques to improve the resistance to the plastic deformation in surface layer.

Jan 1, 2004

By Paul G. Dunn

Safe rapid drift development results principally in reducing exposure of underground workers to the working face. This reduction in exposure is not achieved until either the rock walls have been suitably scaled or sufficient support has been put in place. Rapid drifting enables quicker access to orebodies (increasing returns), higher production rates and a resultant lower cost of mining. The Mining Innovation, Rehabilitation And Applied Research Corporation (MIRARCO) has been developing technology and a methodology for safe rapid drift development within the underground metalliferous mining industry. In terms of rock scaling for underground metal mines, there is still considerable use of manual and mechanical impact rock scaling techniques. Two main issues result from this approach. The first is that in highly stressed or highly fractured ground, a decision has to be made as to when sufficient scaling has taken place. This is not always easy to do and hence operator judgment is a crucial element in this approach. During a baseline study of current rock scaling practices, a wide range of scaling practices were observed within five different underground mining operations; this demonstrates the difficulty inherent in the rock scaling quality decision making process. The second issue is related to the exposure of workers to freshly created rock surfaces. In manual scaling techniques this is unavoidable and despite the best scaling practices, accidents still occur. In an attempt to provide an alternative scaling technology, MIRARCO has been investigating highpressure water jet scaling for removing loose rock as part of the drift advance process. This technology not only provides a means by which scaling practices can be engineered (remove the loose material you want to in a given rock mass condition), it is also quicker and easily automated. Automating the scaling process removes workers from exposure to freshly created rock surfaces and also enhances the application of spray-on liners through improved adhesion of these support types to the rock surface. This paper describes the water jet scaling technology research and methodology for safe rapid drifting within the underground metaliferous mining industry and highlights the key issues and major drivers behind their continued development at MIRARCO.

May 1, 2004

By Waldbillig. D.

A baseline of the poisoning effect of hydrogen sulfide (H2S) fuel impurities on solid oxide fuel cell (SOFC) anodes was developed using polarization testing. After the baseline behaviour was characterized, tests to study the effect of various H2S concentrations on the rate and amount of cell voltage degradation and recovery were performed. Attempts were made to improve the rate and amount of recovery by various methods. Testing was very reproducible, but significant electrochemical performance degradation was seen after all H2S poisoning tests even at an H2S concentration of 0.1 ppm. Degradation is initially quite rapid, but after a period of time the rate of degradation levels off. After poisoning was complete, the H2S flow was stopped and the cells were allowed to recover. Some recovery was seen after poisoning, but cell performance was never fully recovered.

Jan 1, 2005

By W. Baranek

The paper describes activities undertaken for intensification of copper cathodes production in electro-refining plants of the Polish copper smelters: 'Legnica', `Glogów I' and `Glogów II'. In the 'Legnica' smelter, Outokumpu?Wenmec machine was used for preparation of copper anodes. Intensive studies were conducted in order to optimise copper electro-refining conditions. As the result of them, spacing between the electrodes was reduced to 99 mm, which enabled placing forty-one cathodes in each tank and increasing amperage from 10.8 to 13.0 kA. This modification resulted in the increase of electro-refining capacity to 103,000 tons/y. Intensification of the copper production at `Glogów II' by 18,000 tons/y became possible after development of new electro-refining procedures, including application of a regime of changes in electrolyte level during the cathode cycle, implementation of the changes in location of starting sheets relative to anodes, and in dimensions of the sheets, and modification in the shape of the anodes. Similar works have been performed at `Glogów I', which were concentrated mainly on defining of a new method of anodes preparation, modification of their geometry, determination of optimum current density, composition of a set of inhibitors and of a method of their introducing. The implemented solutions resulted in the increase in electro-refining capacity at `Glogów I' from 207,000 to 240,000 tons/y.

Jan 1, 2007

By D. E. Ayres, J. Farstad

"The Midwest uranium deposit is located within the Athabasca Basin near its eastern margin and displays many of the features seen in a number of other similar deposits in this area. The mineralization occurs in the vicinity of a tectonically disrupted portion of the unconformity separating the clastic sedimentary rocks of the Helikian Athabasca Group from Aphebian pelitic meta-sediments which are equivalent to the basal pelitic meta-sediments of the Wollaston Group. The orebody consists of pods of massive pitchblende and sulphur-arsenides within an elongate and tablular envelope of disseminated and fracture controlled mineralization. The massive pods are intimately associated with overbank mudstones of the lowermost Athabasca Group. Both structure and lithology have played major roles in localizing the deposit as follows:1. The basement lithology influenced the mineralogy of the regolith produced on the pre-Athabasca unconformity.2. The style of clastic deposition and the character of the regolith on this unconformity favoured local preservation of mudstones.3. The basement lithology influenced the location of zones of post-Athabasca faulting.4. The proximity of these fault zones to mudstones provided for the coincidence of circulatory channels for fluids bearing uranium, with a good precipitant for the metal.IntroductionA brief summary of the geology of the Midwest uranium deposit was presented by J. Farstad (1979) to the attendees of the Saskatchewan Potash and Athabasca Basin uranium deposits field trip organized by the Canadian Institute of Mining and Metallurgy (May 28 to June 1, 1979). Since that time a substantial amount of data has been collected and studied. This paper is a precis of a report by J. Farstad (1981) which summarizes the geology of the deposit as inferred by visual examination of diamond drill core, augmented by information obtained from detailed examination of selected cores by D.E. Ayres."

Jan 1, 1986

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Mines Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840 µm to 1200 µm in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding , smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840 µm to 1200 µm class reported to the 600 µm to 840 µm; this figure is much higher than for silica (46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50 urn to JOO pm to 20 at 500 um to 1000µm.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840 µm to 1200 µm to the 600 µm to 840 µm class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photograhic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase over-all gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydro cyclones takes place at a much finer cut-size than ore, 20 µm vs 57 µm. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty-four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3 in.) Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89% and 92% for the PCUF and secondary mill discharge."

Jan 1, 1991

By E. L. Chanturiya

The research and characterisation for compositional, physicochemical, structural, electrical and flotation properties of various pyrite samples for a copper-zinc sulfide ore was carried out. Various methods were used during the research, such as optical microscopy, X-ray diffraction, electron probe micro-analysis (EPMA), phase emission analysis, routine chemical analysis, auger electron spectroscopy (AES), scanning electron microscopy (SEM), back-scattered electron images (BSE), potentiometry, and instrumental neutron-activation analysis, flotation. Analysis of obtained results established the interrelation between impurity structures and concentration of electric charge carriers in minerals, Butyl xanthate sorption and flotation yield of pyrite. The research concluded that pyrite samples differ by morphology, micro defects of structure, concentration of donor and acceptor impurities (Co, As, Sb, etc.) and conductivity parameters (thermo-electrical force, specific resistance and concentration of charge carriers The peculiarity of pentagon-dodecahedral pyrite is the high concentration of electric charge carriers (electrons) and the more negative surface potential (by 25–75 mV) in comparison to cubic pyrite. The surface of cubic varieties is more active, therefore it is oxidized in alkaline lime medium much faster, than the surface of pentagon-dodecahedral varieties. This phenomenon is caused by high reaction ability, irregular jointing and defects of cubic pyrite. This promotes the increase of calcium ion sorption on its surface and the decrease of Butyl xanthate sorption. According to this, an increase in alkalinity (lime medium) from a pH of 10.0–11.5 leads to an increase of gold content reporting to the tail of bulk flotation. Gold content is increased from 0.58 g/t (?? 9.5) to 1.9 g/t (?? 11.6), which represents an increase in gold recovery of 24.68 to 79%, respectively.

Jan 1, 2016

By T. R. Madhavan

The development of contact angles on highly polished ?uraninite surfaces, using sodium oleate and dodecyl ammonium acetate as collectors, has been studied at different collector and hydrogen ion concentrations. It was found that sodium oleate in acidic media (up to a neutral: PH) and dodecyl ammonium acetate in neutral and alkaline media give good contact angles. It appears that the combined forms of these collectors, viz., oleic acid and free amine, are more important in effecting contact. W ITH the emergence of uranium as a strategic metal in the last fifteen years, considerable effort has been directed toward the commercial recovery of uranium from its ores. This has resulted in the development of a uranium technology. It is only in recent years, However, that fundamental data regarding the floatability and surface properties of uraninite and ?pitchblende have been elucidated by different methods. Contact-angle measurement is one of the important tools for tl1e evaluation of the conditions of floatability

Jan 1, 1964

By G. R. Sadowski

"Large subhorizontal joints have been found in the foundation excavations in basalt and granite of Brazilian Dams. Some spread for hundreds of square meters showed slickensides—polished surfaces plus striations—and laminations interpreted as related to shear displacement, what substantially reduced their shear strength and imposed special reinforcement measures against the potential sliding of overlying concrete structures. The geological characteristics of these discontinuities have raised speculations related to their origin, be it related to mechanisms of bulging, cambering or to some tectonic or primary geological event.Several geologists and engineers from the northern hemisphere including Terzaghi already showed to be concerned with their role in granite foundations while in the southern regions Brazilian authors have found similar occurrences but also affecting individual lava flows of continental flood basalts in the foundations of major dams of the Parana Basin, which they designated under the particular name of “fault-joints”. This double-standard designation is self-explanatory of the difficulties involving their origin and related geomechanical properties: faults or just shear joints?Recently, similar features were encountered in the foundations of large dam constructions in anorogenic granites inserted in the realm of the Brazilian Amazon, where some of these discontinuities exhibit features common to tectonic thrusting combined with deep tropical weathering.The evidence of preshearing along the surfaces of such fractures, also associated to products of deep weathering, reduces their geomechanical strength substantially, suggesting values of ultimate phi spanning 12 to 28°. The detection of these descontinuities during initial investigation phases continues to be a major complex task in geological risk evaluations surveys. Trenching associated to some geophysical exploration techniques, although considered to be very basic exploration techniques are still the suggested methods for their forecast and previous determination."

Jan 1, 2015

By G. J. Hawkes

"We all know that every man who works for us should have a thorough knowledge and understanding of his responsibilities. But how about ourselves? Du we have a thorough knowledge and understanding of our own responsibilities as Mill Superintendents?I once had an occasion to say to a Manager that I did not know something was my responsibility and he replied with suitable emphasis ""Everything inside those four walls is your responsibility"". That makes the extent of our responsibilities clear but does not give us a check list to keep an eye on as we do our job from day to day.What are our responsibilities? I suggest they are the following:1. Developing and maintaining efficient operating and maintenance crews.2. Milling the required tonnage.3. Recovering the economical maximum amount of gold.4. Keeping costs at the economical minimum.5. Seeing that the figures are reasonably accurate for tonnages, assays, production, losses, and costs.6. Preventing accidents.7. Preventing fires.8. Maintaining the equipment and building and keeping them clean and tidy.9. Enforcing company rules and regulations."

Jan 1, 1965

By Michael P. Davies

Mine waste facilities, and in particular tailings impoundments, are one of the highest risk aspects of any mining venture. There are far too many recent examples of how real and/or perceived physical or environmental impact from one of these facilities has had enormous economic impact on both the specific project and the overall parent mining company. In many cases, such dramatic impacts have followed a period where a due diligence of the mine had been carried out (e.g. in an acquisition, merger or similar) or an internal or otherwise audit had taken place. Consequently, it is suggested that there is a need for an audit/due diligence framework to assist those processes in terms of assessing mine waste facilities. This paper presents a recommended framework for completing either an audit or due diligence assessment of mine waste facilities under a number of typical scenarios. The framework will be of relevance to reviews carried out prior to mine construction, during operations and for mines that have been in a care and maintenance position and are to be re-opened. Concepts of risk management are introduced as an essential part of the recommended framework. The paper should be of value to current and prospective mine owners involved in stewarding an area of significant risk to viability of their mining venture. The paper should also interest prospective lenders to these ventures.

May 1, 2007

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By M. Olper

Commercial copper plants utilising current best technology are tending towards ever increasing scale, the concentrate requirements of which cannot be serviced by a single mine. In such cases, raw materials are often sourced from different mines, which are often far away from the production plant and usually with very different ore compositions. These plants tend to use the traditional thermal processing steps of smelting, converting to blister, anode refining and casting to produce copper anodes that are then refined in a sulphate electrorefining operation. These thermal steps are in some cases troublesome and require the recycling of considerable quantities of material. A new process was developed taking advantage of the latest developments of the first thermal step of the classic loop, the smelting of copper concentrate to high grade matte or white metal using the well known AUSMELT Top Submerged Lancing Technology. The white metal and/or high grade matte product is converted directly to copper cathode and elemental sulphur using the ECUPREX technology. This approach provides an alternative to the traditional thermal steps of conversion to blister, thermal refining and anode casting, which, especially at small scale, can be expensive and problematic in terms of technical and environmental concerns. At first evaluation, this new process can be operated at low capacities, thereby, changing the traditional approach to copper production. Instead of taking the concentrate to the copper production plant, the copper production plant is taken close to the mine with some significant economic and technical advantages.

Jan 1, 2007

By Candido Bariáin

A new vapochromic material of formula [Au2Ag2(C6F5)4(bipy)2]n (bipy = 2,2´ bipyridine) has been developed and used for the detection of some volatile organic compounds as acetone either in vapour or in water solution. The material is presented in the form of powders which colour changes with acetone vapours turning from bright yellow in the absence of vapour to white in the presence of vapour. By using the sol-gel technique, the powder ? dispersed in tetraethyl orthosilicate- was easily deposited on optical fibres. In order to study experimentally the behaviour of this material for construction practical optical fibre sensors, a sol-gel material doped with the vapochromic material is deposited onto an extreme of a monomode fibre connected to a coupler. The behaviour of the material was studied for different wavelengths and concentrations of acetone vapours and acetone/water solutions. Changes up to 4dB in the reflected optical power were detected. Optical fibre sensors have many advantages over conventional ones, such as electromagnetic interference immunity, passivity behaviour, possibility of using multiplexation techniques, low weigh and little size, etc. Actually, there is an increasing interest in developing optical fibre sensor for vapour detection in the chemical industry and in fact many sensor had been developed [1]. Some are based on the deposition of a sol-gel-based material either over the core of an optical fibre [1] or onto the thinner zone of a biconically tapered optical fibre [2]. Others are based on Fabry-Perot interferometers [3]. Also there are sensors based on the reflection of the light on films, on the fluorescence of dye-doped polymer cladding in fibre, on colorimetric reagents in the core of a silica fibre or on surface plasmon [4]. The possible materials for the construction of such sensor should be colorimetric reagents able to change the colour or refractive index in the presence of same organic vapours. There are not many metallic complexes with these properties, although same interesting examples have been reported in the chemistry of palladium and platinum as [Pt(p-R-C6H4NC)4][Pd(CN)4] described by Nagel [5] and Mann [6], which reported the construction of some LEDs. We recently reported the preparation of a novel vapochromic material (Fig 1) [7] which can be used for the construction of optical fibre tapered environmental sensors [8,9] of vapour organic compounds (VOC´s). Also we reported other nickel and palladium derivatives which present this type of behaviour [10]

Oct 1, 2003

By R. Sharma, I. Miskovic, S. Miskovic

Solvent extraction (SX) is a widely used method for the extraction of copper from pregnant leach solutions or other ionic solutions in hydrometallurgical applications. About 17% of total refined copper production worldwide is produced using SX followed by electrowinning (EW). Conventional SX units, such as mixer-settlers, consume a large amount of extractant, offer poor process control and yield low extraction efficiency. Extraction efficiency is poor due to low specific interface area, crud formation, emulsification, and slow phase separation stage. Micro solvent extraction (micro-SX) is a rapidly developing technology that provides an opportunity for improved process control, higher extraction efficiency, lower residence time and, as such, has a potential to reduce the environmental footprint of SX operation. In this research, extraction of copper ions in an acetate buffer media is investigated using D2EHPA with kerosene as a diluent. Chemical factors such as extractant concentration and ionic concentration of aqueous phase are varied to determine the optimum conditions. Subsequently, the extraction efficiency and reaction time of new micro-SX reactors are compared against previous bulk SX studies. Extraction in the microfluidic reactor was observed to be faster with a residence time more than an order of magnitude lesser than bulk SX. This study forms a prelude for developing new modular micro-SX units which will enable continuous, effective, and safe operation on a large scale. In future studies, numerical and analytical models validated through this work will help eliminate rigorous experimentation and enable faster design and fabrication of micro-SX units. INTRODUCTION Conventional industrial solvent extraction (SX) units such as mixer-settlers, extraction columns present various disadvantages. Low specific interfacial area, crud formation, and emulsification in industrial reactors lead to long extraction times and severely hamper extraction efficiency (Priest et al., 2011; Chen et al., 2017). Microfluidic extraction considerably improves upon the current extraction practices by (1) creating a large surface to volume ratio that enables rapid mass transfer across the interface, (2) better process control, and (3) easier separation of phases (Kashid, Renken, & Kiwi-Minsker, 2011; Ciceri, Perera, & Stevens, 2014). These factors establish micro-SX as a crucial mode for process intensification. Although, a micro SX unit has significantly low processing volume than conventional extraction methods, their throughput can be increased via massive parallelisation (‘numbering up’), which is an area of active research (Darekar, Singh, Mukhopadhyay, & Shenoy, 2016a; Kriel, Woollam, Gordon, Grant, & Priest, 2016).

Jan 1, 2019

By G. Vibert Douglas

Introduction A preliminary paper dealing with the subject of ore-shoots was presented to this Society at its Annual Meeting last year (1). The present paper records the attempts which have been made during the interval to further this study. In reporting this work, I wish to state that I do not consider the investigation complete; many more experiments will have to be carried out, and more field data will have to be recorded, before the geologist can say with confidence an ore-shoot should start at this point and pitch in that direction. The aim of these experiments is to find some criteria which will serve the mining engineer and mining geologist concerned with ore-shoots in hydrothermal veins.

Jan 1, 1935

By H. J. Meyer

"A hydrostatic elevation difference meter has been developed for use in measuring elevations along gravity traverses. Elevations of stations 100 feet apart can be obtained at a rate of 1/2 mile per hour and to an accuracy better than 1/3 foot. This can be done along traverses which have not been cut and chained. The instrument is durable, lightweight and constructed of materials which will withstand any temperature encountered in field work.It is believed that this device will more than double the rate at which gravity surveys over mining prospects can be carried out."

Jan 1, 1972

By Bish Chanda

In the minerals business, like any other commodity-based business, management faces the daily challenge of holding down costs while the real prices of products are continually falling on an inflation-adjusted basis. Since the marketplace sets the prices, often without any premium attached for product quality, being one of the lowest-cost producers is the most viable competitive strategy. Continuous improvement is the mantra that can make the difference in terms of long-term survival of a mining company. Yet, this message has not always been followed, especially during periods of prosperity ushered by high commodity prices. More often than not, the need for improvement is only triggered by a crisis. This may be caused by events such as the onset of a severe economic recession, a prolonged oversupply situation due to an optimistic expansion of capacity during the period of prosperity, or simply falling profits alerting management to bring costs under control. At that time, there would be a need to implement a new cost-saving program, bring in a consultant to find ways to reduce costs, or re-activate an old program that had been shelved for some time.

May 1, 2003

By Mostafa Benzaazoua, Bruno Bussière, Jean Lelièvre

De nombreuses opérations mimères exploitent et traitent des minerais sulfurés pour concentrer des métaux precieux (Au, Ag ... ) OU des métaux de base (Cu, Pb, Zn ... ), laissant en fin de parcours des tonnages considérables de résidus plus ou moins générateurs de drainage minier acide (DMA) selon leur contenu en sulfures. De nos jours, Jes restrictions en matière de protection de l'environnement obligent Jes opérateurs miniers a trouver Jes solutions Jes plus efficaces pour préserver Jes sites environnants de la pollution due a l'oxydation des sulfures. Cette oxydation cause une acidification accrue du milieu et une mise en solution des metaux toxiques. L'utilisation des recouvrements multicouches est l'une des solutions Jes plus efficaces pour limiter la pollution liée au DMA mais entraine des coilts de construction qui sont souvent considérés par l'industrie miniere comme prohibitifs. Une façon de rendre cette technologie applicable, d'un point de vue économique, est de désulfurer Jes résidus à l'usine de traitement et d'utiliser la fraction inerte comme composante d'un recouvrernent multicouche. Cette opération de desulfuration peut etre réalisée par flottation non sélective des résidus dans le but d'obtenir d'une part un faible volume de concentré de sulfures qui devra être géré convenablement et d'autre part un rejet non générateur d'acide.

Jan 1, 1998

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995