Search Documents

By S. M. Bradshaw, E. Charikinya

"Microwave induced cracks have the potential to enhance metal recovery from coarse sphalerite particles in heap leaching operations by creating new crack surface areas for lixiviant and enhancing value mineral exposure. The mode of fracture and the extent of mineral exposure due to microwave induced cracks have not yet been investigated. The objective of this study was to determine the extent of particle damage and mineral exposure in microwave treated particles. This was done using X-ray computed tomography (XCT) and image analysis techniques. XCT analysis was conducted on small (–5+4.75 mm), medium (–16+9.5 mm), and large (–25+19 mm) sphalerite ore particles before and after microwave treatment (MT). Geometrical properties, such as volume and surface area of each mineral phase in each particle was determined from the XCT reconstructed images using VGStudioMax image analysis software. These geometrical properties were used to calculate the interfacial areas of sulphide mineral grains in microwave treated particles before and after MT. The ratio of specific interfacial area after MT to specific interfacial area before treatment was used as an indicator of the degree of preferential grain boundary fracture. The results showed significant grain boundary fracture after MT at all sizes. For small sized particles, about 31% of the interfacial area was lost compared to 23 and 16% for medium and large particles, respectively. The results also showed an increase in the degree of mineral grain exposure of 28, 26, and 15% for small, medium, and large particles, respectively, after MT. These results provide experimental evidence supporting improved mineral exposure due to MT. INTRODUCTIONFor some years it has been suggested that microwave treatment (MT) of ores might result in preferential grain boundary fracture that would have benefits such as improved grain exposure and particle weakening. (Kingman, 2006). Most of the experimental work investigating the application of microwaves to mineral processing flow sheets has focused on assessing the benefits of applying microwave technology to flow sheets consisting of size reduction and mechanical flotation cells (Kingman et al., 2004). Experimental studies have shown that coarse crushing during tertiary grinding of microwave treated ore resulted in a better liberated coarser flotation feed (Scott, Bradshaw, & Eksteen, 2008). It has been suggested that improved liberation in milled flotation feed, was due to the presence of grain boundary fracture in microwave treated particles. However, this improvement in coarse particle liberation does not necessarily translate to a significant improvement in downstream flotation recovery (Kobusheshe, 2010). This is as a result of the size limit to the flotation of coarse material, due to detachment forces acting on particle-bubble aggregates, which increase as the particle size increases (Jameson, 2012). Current conventional, mechanically agitated flotation cells are not designed to float coarse material (Jameson, 2012). Hence it has been difficult to show the downstream processing benefits of applying microwaves to ores processed by comminution followed by flotation (Kobusheshe, 2010). It is clear from investigations carried out so far that inappropriate downstream exploitation of microwave treated ore would fail to realise a meaningful process benefit (Kobusheshe, 2010; Ali & Bradshaw, 2011)."

Jan 1, 2016

By Kevin Bell

About Beltek Inc. For more than a decade Beltek, Inc. has been working with national and international organizations to harness and deliver solutions which gain real ebusiness advantages in today's world. Our objectives are to partner with our customers to achieve maximum results, while reducing costs. At Beltek, we provide a commitment to you and your organization's needs. Whether that be delivered by ensuring our services and products are state of the art or by providing a level of personalized service, which makes you feel like the center of attention, Beltek is about adding value to every job we work on. The individuals who work at Beltek quickly become your friends because we share your passion and enthusiasm for the business we are in. That's why every person is a leader in his or her respective fields. Having these individuals as apart of our business ensures you get the best out of our equipment, receive the very latest in advise, problem solving and support. We also pride ourselves on our ability to remain flexible at all times because we know deadlines and schedules can change quickly, so we always go the extra mile to deliver exactly what you need.

May 1, 2004

By L. Dubourg, H. Habibi, D. Rasmussen

The combination of laser welding with Gas Metal Arc Welding (GMA W) forms the hybrid laser-OMA W welding. This process is an attractive tool with a high potential in welding lightweight structures, especially for aluminum alloys. For five years, this technology has increasingly attracted interest in both, industry (aeronautics, automobile, metal industries producing large structures) and academia (universities and research centers). Hybrid laser-OMA W welding process is generally accepted for its robustness, efficiency and flexibility. Coupling of a deep-penetrating laser beam with the heat and molten metal feeding of GMA W significantly expands the original welding application range of lasers. Its main advantages compared to the two individual components are deep and stable weld penetration, gap-bridging ability improvement, low distortion and easy filler metal addition. Hybrid welding allows a much wider groove tolerance compared to laser welding, especially for aluminum welding. Moreover, the reduction in distortion decreases the post-welding rectification needed and makes the assembly easier. In addition, if metallurgical factors are critical, the weld composition can be balanced with filler metal, decreasing the hot cracking susceptibility of some aluminum alloys. The combination of these two welding processes can also improve the weld bead shape quality (including the elimination of undercut), possibly reduce the porosity and increase the welding speed. This article reviews the recent works about the laser-OMA W hybrid welding of aluminum alloys. After a brief presentation on the interaction mechanisms between a laser beam and an electric arc, the paper depicts the typical welding parameters and experimental methods along with their characteristics.

Jan 1, 2006

By J. P. Cooney

Placer Dome is learning from experience in Latin America, Asia and Africa, as well as in North America, that contributing effectively to sustainable human progress in the areas of its operations presents unending challenges to think creatively, communicate effectively and remain culturally sensitive. People must be better off in terms of their economic circumstances, their social conditions and the quality of their natural environment not only during the life of the mines, but after mines close. Stakeholders, all those who are directly or indirectly affected by a mining project, should be able to participate in decisions which affect them. The development of sustainability strategies, the monitoring of sustainability performance and the implementation of sustainability programs are best done in partnerships with governments, communities, nongovernmental organizations and multilateral development institutions. Ultimately, the success, if not the survival of mining, will depend on our ability to get the sustainability equation correct.

Jan 1, 2000

By L. B. Hale

"Introduction This paper will discuss the current operations of Westar Mining Ltd. and give a brief history of the company and of the Crowsnest Pass area. Westar is an integrated company involved in mining, processing and marketing coal from its mines in southeastern British Columbia and shipping coal from Westshore Terminals at Roberts Bank, located just south of Vancouver, B.C. It is two-thirds owned by the B.C. Resources Investment Corporation and one-third owned by the Mitsubishi Corporation of Japan and a consortium of Japanese coal consumers. Operations in southeast British Columbia consist of four coal mines and two processing facilities (Fig. 1). The Elkview Coal Processing Plant near Sparwood, B.C. receives its raw coal from Balmer operations (Harmer open pit), Balmer South (Panel 6) an underground hydraulic mine, and Balmer North an underground room-and-pillar mine. The fourth mine, Greenhills, an open-pit operation, is located near Elkford, B.C. and has its own processing plant. The Balmer mining and processing complex is the largest metallurgical coal facility in Canada producing up to 7 .5 million tonnes of clean coal per year. The Greenhills operation, completed in mid-1983, has a capacity of 2.8 million tonnes. The high-grade metallurgical and thermal coal produced is primarily for export markets. The major customers are Japan, Korea, Brazil, Pakistan, Chile and Taiwan.Our coal and that produced by other mines in Alberta and British Columbia is shipped to the international markets through Westshore Terminals Ltd., a wholly-owned subsidiary. Westshore will have an annual capacity of 22 million tonnes of coal and accommodate ships of up to 250,000 dead weight tonnes by 1984 when its current expansion program is completed."

Jan 1, 1985

By Irving Wigden

The world is fast becoming information based. Mine companies migrate business infrastructures to be handled electronically. Suppliers move onto the worldwide web. In this ?e-world? successful suppliers will recognize they no longer trade in just equipment, but in knowledge. Companies can no longer just provide products and services, but instead must find ways to harness their knowledge to provide new value for customers. Mine customers will be attracted to suppliers that can help them streamline the process and use Information Technology to optimize operations, increase profit, reduce cost and enhance shareholder value. With the continued move to industry standard communications and software platforms, technology that formerly stood alone can now be integrated with other technologies. This creates more powerful systems that mine operators can use quickly, easily and cost effectively. These unified architectures improve productivity, provide higher asset optimization and allow more informed decision-making. As a leading supplier of process automation solutions for the industry, ABB provides a dynamic range of such control systems. These systems are designed for instrumentation controls, variable speed drives, electrical distribution, electrical equipment and related services for Mine Automation. Enhanced by ABB´s new family of integrated software solutions ? collectively known as Industrial IT ? ABB´s control and Scada systems place you in the best position to optimize your plant, process and enterprise operations. The paper discuss system integration and installation of High-Tec system in an underground mine. ABB has the ambition to be a System Integrator and co-operate with partners in different areas of technology. To day it is a problem to find one Supplier that can be responsible for the complete Automation System. The design of the system is also much depending of the design of the mine and also which caving procedure that is used in the current mine. Much of the work must be done in a feasibility study and during the design phase. If there is careful planning and consideration during these phases is vital in order to avoid costly changes during the commissioning phase The paper will also include a presentation of the benefit of using Automation in an Underground Mine, and how important the integration of the Human Being is to the Automation System. The most profit gained in mining industries are received when the mines can reduce internal and external disturbances in the production flow and speed. Must of the experience and discussed in this paper is from advanced technology, that has been developed in Scandinavian and adopted of LKAB in Kiruna. The author of this paper has been responsible för the Automation projects in the Kiruna Mine during 1994 - 1999. These projects include: Broadband communication of data, audio, compressed video in one data stream. Control System for Haulage -1045m Automation of Load Haulage and Dumping machines (LHD) Control of Production Drilling Riggs from a Central Control Room.

May 1, 2002

By Irving Wigden

The world is fast becoming information based. Mine companies migrate business infrastructures to be handled electronically. Suppliers move onto the worldwide web. In this ?e-world? successful suppliers will recognize they no longer trade in just equipment, but in knowledge. Companies can no longer just provide products and services, but instead must find ways to harness their knowledge to provide new value for customers. Mine customers will be attracted to suppliers that can help them streamline the process and use Information Technology to optimize operations, increase profit, reduce cost and enhance shareholder value. With the continued move to industry standard communications and software platforms, technology that formerly stood alone can now be integrated with other technologies. This creates more powerful systems that mine operators can use quickly, easily and cost effectively. These unified architectures improve productivity, provide higher asset optimization and allow more informed decision-making. As a leading supplier of process automation solutions for the industry, ABB provides a dynamic range of such control systems. These systems are designed for instrumentation controls, variable speed drives, electrical distribution, electrical equipment and related services for Mine Automation. Enhanced by ABB´s new family of integrated software solutions ? collectively known as Industrial IT ? ABB´s control and Scada systems place you in the best position to optimize your plant, process and enterprise operations. The paper discuss system integration and installation of High-Tec system in an underground mine. ABB has the ambition to be a System Integrator and co-operate with partners in different areas of technology. To day it is a problem to find one Supplier that can be responsible for the complete Automation System. The design of the system is also much depending of the design of the mine and also which caving procedure that is used in the current mine. Much of the work must be done in a feasibility study and during the design phase. If there is careful planning and consideration during these phases is vital in order to avoid costly changes during the commissioning phase. The paper will also include a presentation of the benefit of using Automation in an Underground Mine, and how important the integration of the Human Being is to the Automation System. The most profit gained in mining industries are received when the mines can reduce internal and external disturbances in the production flow and speed. Must of the experience and discussed in this paper is from advanced technology, that has been developed in Scandinavian and adopted of LKAB in Kiruna. The author of this paper has been responsible för the Automation projects in the Kiruna Mine during 1994 - 1999. These projects include: Broadband communication of data, audio, compressed video in one data stream. Control System for Haulage -1045m Automation of Load Haulage and Dumping machines (LHD) Control of Production Drilling Riggs from a Central Control Room.

May 1, 2002

By John Convey

"IRON ORE was first smelted in Canada about the year 1736 at Les Forges, Quebec -a most appropriate name for such a historic locale. During these early years of the 18th, 19th, and first quarter of this century, about six million tons of ore were mined and employed in the manufacture of items ranging all the way from kettles, stoves, and cannon for the early settlers to weapons of war for the allied armies of World War I.But this symposium on iron ore is not concerned with this early period. Instead, it is concerned with the iron ore industry of today -an industry which will soon be-come one of the two most valuable mineral industries in Canada.The subject in its broad geographic and economic aspects will be introduced by Mr. Buck; Dr. Harrison will describe the geology and origin of the principal iron ore deposits; Dr. Downes will go into beneficiation as it applies to iron ores; and Mr. Gertsman will discuss primary processing. The symposium will not deal with the steel end of the industry, because that phase itself could well form the subject of a symposium."

Jan 1, 1955

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the last decade. Accidents rates are improving but more slowly and yet, serious accidents and fatality rates are not: in fact, these rates of more serious incidents have plateaued or deteriorating. In more dramatic cases, organizations that had ?exemplary? safety statistics, suddenly had a catastrophic or multi-fatality event occurring. Popular books such as In Search of Excellence of Peters and Waterman or Good to Great of Jim Collins created many delusional ?secrets? or recipes, to achieve great performance and yet, most of those ?great? or ?excellent? companies have now declined in their performance, some dramatically and some have fallen from grace, like Fanny Mae, a company Jim Collins identified as a ?great? one, that had to be bailed out in the latest financial crisis. These organizations share several ?delusions? about managing a business, and often, these delusions are created by academics, consultants and authors of popular books about (safety) management. More damaging however is that safety management is defined by a set of key practices or axioms: a focus on human error, compliance to rules and regulations, creating consistency of systems and actions, reacting to accidents and incidents and on prevention of those, measuring safety with performance metrics and rewarding employees on those measurements. All of these axioms contain the seeds of destruction, and they create conditions and dynamics that precede the disaster - and ironically, they are all 'good things' we do in safety management. For example, a mere focus on safety in the business, and the measurement of it, create a culture of repression of mistakes and incidents, leading to a situation where the organization knows incrementally less and less of risks and risktaking behaviour - until the day it all coincides destructively! This paper discusses seven such safety delusions and how they impact on the views and safety management approaches. They are: ??The delusion of (risk) control, that risks can actually be identified, analyzed and mitigated. ??The delusion of compliance, that mere compliance to rules will safeguard the business ??The delusion of consistency, that standard operating procedures will ensure safe operations ??The delusion of predictability, that accidents and trends tell us everything about the risks of the future ??The delusion of human error, that people are the weakest link and that it can actually be dealt with through discipline and enforcement. ??The delusion of statistical trends, that safety is measurable with statistics ??The delusion of invulnerability, that we have achieved high levels integrity and capability to deal wit risks. Organizations that suffered catastrophes all share some or all of these delusions and this paper traces how these played a role in many disasters, ranging from the Titanic, Challenger, Piper Alpha, Bhopal, BP Deepwater Horizon and many more.

Aug 1, 2013

Research, whether applied or fundamental, is a human endeavour which increases our understanding of nature. It is insufficient to simply observe, explore, record and classify. It i necessary, as well, to fit the observations into a satisfying theoretical scheme; that is, to synthesize. Two examples of successful research programs in physical metallurgy are di cussed from this point of view. A pessimistic view is taken of the prospects for rapid growth of research activities in the Canadian metallurgical industry. THE term "research" is used indiscriminately to describe any intellectual or experimental activity which leads to a change in society. Proponents of various activities, ex-tending all the way from alloy development to subliminal advertising, use the status of the term for special advantage. With the Canadian Government entering upon a project of support to industrial research, it might be well to determine what definition is most in the public interest. As an academic, I have a rather jealous attachment to the definition that research, whether applied or fundamental, is a human endeavour which increases our understanding of nature.

Jan 1, 1963

By W. G. Scott

IT IS APPROPRIATE that your Institute should have chosen, for its 1956 Annual General Meeting, the Capital City of a province which is making such rapid advances in mining. The railway industry is proud to be playing an active role in this development, expenditures on equipment and railway construction in the Province of Quebec alone in recent years being in ?excess of a quarter of a billion dollars. In looking up some background material for this address I ran across a definition of a mine by Mark Twain, the great American humorist, which I thought might amuse you. He said that a mine was "a hole in the ground owned by a liar". I am sure that if he were alive to witness the enormous value attached to Canada's mineral resources today he would quickly change his definition. Canada's postwar record of mining development has been staggering in its variety and enormity. Historically, only the ?construction of our transcontinental rail ways outranks the largest of three of these development projects - the aluminum undertaking at Kitimat; the Quebec-Labrador iron ore deposits ; and the petroleum and natural gas developments in Wes tern Canada.

Jan 1, 1956

By M. Myllymäki

"Pre-treatment of mill feed in a minerals processing plant enables for higher production efficiency per ton of product, reduction of consumables and diverting mineral feed types. Sensor based particle sorting allows for pre-concentration of the run-of-mine (ROM) material prior to other concentrating process. Various sensors provide different responses from the minerals in measured particles. The capability of “accepting” or “rejecting” particles based on sensor responses is investigated in specific test work for each project. Modern sorting machines use pneumatic actuators to divert the reject particles from the material stream. This paper discusses the incorporation of ore sorting test work in processing and plant design. When taking the effects of a sorting circuit into account early in the process planning phase, the downstream process can be adequately sized and impacts evaluated. Potential benefits include but are not limited to increased head grade, lower tonnage to the mill, increased mining operations, removal of deleterious elements and changed properties in the process feed. In a case study we present the Keliber lithium project in central Finland. The plant will produce 9000 tons of lithium carbonate per year from a spodumene ore. Ore sorting and flotation tests were carried out in laboratory and pilot scale. Process models were designed and simulations performed using Outotec’s HSC Chemistry Simulation software. Changes in the flotation performance (grade, recovery, impurity levels) were simulated with and without the pre-concentration of the ROM material. The metallurgical performance and mine economics of the different operational scenarios were evaluated using the Ore-Met optimizer module of the simulation software.INTRODUCTION Challenges in the recent years such as declining ore grades, increasing energy prices, scarcity of water and increasing environmental regulations raise the demand for more efficient processing technologies. Sensor based sorting offers a method for pre-concentration or waste rejection at an early process stage. The technology analyzes each rock particle separately for their unique physical and chemical properties, and diverts the particles into separate material streams by high pressure air jets. Successful implementation relies on ore heterogeneity, differential sensor response and suitable feed preparation."

Jan 1, 2018

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By D. Rylander

The operation of Quarry and Aggregate sites are similar to factory production, since it contains sequential production processes, tasks and activities to produce the output product. Compared to the plant though, the quarry processes are generally not synchronized and controlled towards the overall throughput of the site in real time. Some quarries control parts of the production but do generally not utilize real-time technologies for the whole site and all its activities. This fact indicates a general improvement potential in increased productivity at quarry sites, but also unsolved challenges for the same reason. The main contribution of this paper is the presentation of a Lean based method for how to describe the processes to identify control improvement potential within a site. The aim of the identified improvements is to increase overall site productivity by optimizing site, fleet and machine utilization towards the overall throughput, and minimizing operational expenses and inventories. Further the paper exemplifies the method?s usability with field studies at operational quarry plants successfully identifying and quantifying potential wastes and improvements. In addition the identified productivity improvements based on increased control and automation indicate challenges and needs in wireless communication and sensing technologies.

Aug 1, 2013

By R. B. Sudderth, A. Quiroz G., M. Torres M., C. Salgado Q., J. Fernández O., H. Bravo P., M. Torres B.

SNF FloMin, Inc. has introduced a complete line of extractants for recovery of various metals. Among them are the CuPRO MEX™ Brand of copper extractants that are based on the well- known 2- hydroxy 5-nonylsalicylaldoxime and 2-hydroxy acetophenoneoxime. This paper presents the laboratory and pilot plant trial results for SNF FloMin’s CuPRO MEX™ 3302 reagent, the equivalent to the wellknown ACORGA® M5640 extractant, and the composition of these reagents are described. Some examples of SNF FloMin’s CuPRO-Sim™ Advanced solvent extraction simulator are presented.

Jan 1, 2014

"IntroductionIn the 1970s, environmental concerns and associated liabilities were a new and unknown aspect of corporate risk. Today, social concerns and the associated conflicts that they can generate constitute a rapidly expanding aspect of risk. Although not a new phenomena — the Bougainville copper mine was forced into closure in 1988 — social risk has emerged as considerably more important, and increasingly visible, in the last few years. Social risk is now an aspect of all mining activities which needs to be calculated into project assessments, and to be managed throughout the life of a project. While social risk has a number of aspects at the corporate level, such as company image and shareholder relations, at the level of the individual project, its primary component is social acceptability, and the principal tool for managing it is the Social Licence to Operate.Social Risk in Latin AmericaThroughout Latin America there are newly modernized mineral codes and economic systems introduced over the last ten years which, together with new environmental legislation, look very much like regulations in developed countries. To the corporations, the existence of these instruments means that the risks from the environmental issues associated with the project are known; they are legislated, defined, quantifiable and hence manageable.It seems ironic that, just when comprehensive regulations for the environmental management of mining have been put in place throughout Latin America, there arise an increasing number of challenges to mining activities. For, in spite of the apparent guarantees provided by these new legislative reforms, communities in Latin America today are more frequently standing up and taking exception to the presence of mining companies, or the ways in which the companies are conducting themselves. The viability of projects becomes threatened because they are considered socially unacceptable, a phenomenon that we describe as social risk. These challenges are less about opposing mining activities than many people would think. Rather, they are based on an increasing desire on the part of the local population to have some measure of control over their own future, and to participate in the development process from the earliest stages."

Jan 1, 2000

By H. H. Fairfield

THE production and inspection of the materials of war involves thousands of observations. Logical action is generally based on the interpretation of many observations. The success of such action depends upon the accuracy of the observations and the soundness of the interpretation placed upon them. There are countless instances where the observer 'sees but perceives not'; that is, the significance of a group of observations is lost, due either to faulty interpretation or to no interpretation at all being placed on the results. This condition is being partly corrected in the United Kingdom and the United States (1) by the promotion of certain principles by Ordnance officials. The term Quality Control has been adopted to describe a system of studying and controlling industrial products by methods of handling observations. In these pages an attempt is made to outline in a non-technical manner some of the ideas used in the handling of observations. Of course the authenticity of the observations determines the worth of any decisions based on them. No matter how brilliant is the theory built on unreliable sampling, it is usually of little practical value. n some fields it is almost impossible to obtain observations free from bias. Let us suppose that observers of speed in miles per hour were available for judgment: (a) a bystander, (b) a motorcycle policeman, and (c) a motorist accused of speeding. The bystander might be unbiased but probably would be very inaccurate. The motorist is usually biased on the low side. The policeman is the only qualified observer and, if over-zealous, he might be biased on the high side. Conclusions drawn from large numbers of biased observations naturally would be of little value.

Jan 1, 1943

By A. Zaidi

"The mining and metallurgy industry is highly energy intensive and one of the largest energy users in Canada. Energy costs are also a major component of total production costs in this industry as described in the 1990 Report of The Canadian Industry Program for Energy Conservation (CIPEC). For some plants, energy costs are reported to be up to 30% of total production costs. Therefore, a reduction in energy costs provides an opportunity to improve industry profitability. The specific energy intensity and production costs can be reduced by using modem energy efficient natural gas technologies. In addition, these technologies often improve product quality and increase productivity. Natural gas not only offers economic benefits, but is also environmentally benign as compared to other major energy sources. Emissions of NO"", CO2 particulates and SO2 are lower with natural gas than other fossil fuels.This paper provides a brief overview of some state-of-the-art gas technologies for the mining and metallurgy industry including cogeneration, oxy-air-fuel burners, ceramic immersion tube heaters, direct gas contact process, low NOx burners, and energy efficient liquid heating systems.CogenerationCogeneration is defined as the simultaneous production of electricity or mechanical power and useful process heat from a single fuel source. One of the primary considerations in selecting a cogeneration system is the relative quantities of electrical and thermal energy which are to be produced. Two types of systems are discussed below."

Jan 1, 1993