Search Documents

By Ali Montaser

This paper presents an experimental study conducted to facilitate the use of RFID on construction job sites. The study focuses on deployment settings to provide data acquisition with higher accuracy for indoor location sensing. It provides extension to the state-of-the-art in this field as it addresses the impact of metal media proximity to RFID tags, the reasonable duration for data capturing, number of RFID tags employed and the distance between them. Low cost passive RFID tags were used in the experiments where each tag is used as a reference point with a known location. Five hundred and forty (514) experiments were conducted in lab environment using a 3m by 3m test bed that is dynamically rearranged to generate 15 test beds and a total of 67713 data sets were collected and analyzed. The collected data were captured from nine locations for each test bed at four time intervals. Received Signal Strength Indicator (RSSI) was used as the main attribute for signal measurement to process the captured data. Results of the data analysis performed are studied under four main categories: duration, number of tags, locations of tags and metal interference. The best duration was found to be the 15 second in the test bed with the least number of tags; as the short amount of time to capture data did not allow creation of a lot of interference among the emitted signals. Within each test bed, errors occurred most at points where the received signals were not well distributed in a 360 degree vicinity of the data capturing point. It means that the center point of each test bed resulted in lowest errors and the points located on the extremities led to the highest errors. Finally, metal objects were found to have major impact on the accuracy of the captured data; to the level where reliable values for errors could not be calculated in the test beds attached to metal objects. In summary, the results of the experimental study and related findings are expected to provide guidelines to the users of RFID technology for localization in building construction.

Aug 1, 2013

By K. Law

"The Hatch Product Transport (HPT) system is a highly flexible and configurable route selection and sequencing system for controlling large bulk material handling facilities. The system has a generic control algorithm that can be configured to suit any material handling facility. It can also be easily reconfigured to cater to plant expansion or modifications without incurring significant disruption to the existing production, costs in testing, and re-commissioning, thus achieving cost savings throughout a facility’s lifecycle.This new material handling control system has been installed at BHP Billiton’s Port Hedland iron ore terminal to facilitate its expansion to beyond 100 Mt output capacity."

Jan 1, 2006

By W. A. Gow, H. H. McGreedy

It is believed that many of the problems encountered in the operation of gold cyanidation plants are difficult to resolve due to the lack of sufficient and reliable in-formation regarding the variations and actual values of operating variables at any given time. The application of instruments to monitor the more important variables in the cyanidation process should result in more efficient plant operation and a better understanding of the process. The use of pH and conductivity sensing devices for alkalinity measurements, a monitor to determine the dissolved oxygen content of plant solutions, a continuous cyanide titrator and sonic control of grinding circuits are discussed. Although the discussion is oriented toward the cyanide process, much of the paper is applicable to other ore treatment operations.

Jan 1, 1966

By L. K. Mireku

"Abstract - The Halfmile Lake South Deep zone, Bathurst Mining Camp, New Brunswick, was discovered by Noranda Inc. (Exploration) as a result of a 3-D seismic survey in 1998 and the subsequent drilling of ten diamond-drill cores. The deposit consists of massive, breccia, and stockwork Pb-Zn-Cu sulfide minerals, and is hosted by a volcano-sedimentary sequence belonging to the overturned Ordovician Tetagouche Group. Epiclastic rocks and interbedded fine-grained felsic pyroclastic rocks dominate the stratigraphic footwall. Locally, crystal-rich felsic tuffs and subordinate epiclastic rocks comprise the immediate stratigraphic hanging wall. The entire stratigraphic sequence was intruded by quartz-feldspar porphyritic intrusions, and cut by intermediate and basic dikes. The volcanic and sedimentary rocks can be discriminated geochemically using trace element ratios such as Zr/TiO2 and Nb/TiO2, despite intensive alteration and cleavage development. These ratios indicate that four protolith volcanic compositions exist: rhyolite, dacite, andesite, and basalt. The aphyric and feldspar- and quartz-phyric volcanic rocks are dacitic and rhyolitic in composition; epiclastic rocks have trace element ratios consistent with dacitic compositions. Pearce element ratio diagrams, general element ratio diagrams, and petrographic observations demonstrate that the rhyolitic volcanic rocks exhibit evidence of albite, potassium feldspar, and quartz fractionation, dacitic volcanic rocks exhibit little evidence of any fractionation, and epiclastic sedimentary rocks exhibit evidence of quartz sorting only. Hydrothermal alteration is best represented by the presence of phengitic muscovite and daphnitic chlorite. Minor calcite occurs in the stratigraphic hanging wall, deep in the stratigraphic footwall, and in post-mineralization dikes, and thus is not interpreted to be part of the causative hydrothermal event. Element additions and losses during alteration have been used to determine net alteration reactions, and these have been used to identify alteration parameters that are independent of other forms of alteration and fractionation/sorting, and which can be used to guide exploration. These parameters include: a bulk hydrolysis measure, (2Ca+Na+K-2CO2)/Al; a muscovite alteration measure, K/Al; an albite destruction measure, Na/Al; a chlorite alteration measure, (Fe+Mg-S/2)/Al; a chlorite composition measure, (Fe-S/2)/Mg; a sulfidization measure, S/Ti; and a carbonatization measure, CO2/Ti. With the exception of the carbonatization measure, these alteration parameters define a distinct lateral and vertical zone of intense hydrothermal alteration in the stratigraphic footwall of the deposit, and demonstrate that the epiclastic rocks are predominantly chlorite altered, and the volcanic rocks are predominantly muscovite altered. Within the alteration halo, element additions of Fe and H, and element losses of Na are characteristic. Potassium was added to muscovite-altered rocks, but subsequently removed from chlorite-altered rocks. The results from this study demonstrate that metamorphism and deformation have not significantly obscured hydrothermal alteration signatures."

Jan 1, 2006

By Robert C. Stanley

Early History Probably the first use of nickel by man was in the fashioning of implements, and later swords, from nickel-bearing meteorites, masses of metal that have fallen from time to time at many points on the earth's surface and which consist normally of iron carrying substantial amounts of nickel. Meteorites were perhaps the first metal known to man. The falling star, sought out with fear overborne by curiosity, was found to be a better stone than the earth-given, truly a boon from the gods. Archeologists tell us there is good evidence that the ancient oriental peoples learned at an early date to make these stones into useful implements. The invincible blades of the great warriors of old in China, Persia, and in northern Europe, were Heaven-sent, a fable which sounds significant of meteoric iron. Probably some of the ancient swords of Khorassan and of Damascus were of meteoric nickel-bearing iron (1). Fifty centuries were to pass before men learned to isolate nickel and add it to iron to produce the same alloy for much the same purpose. Meanwhile, man had found another natural alloy of nickel, known first to the Chinese as paktong, or 'white copper.' It was obtained from complex copper-nickel sulphide ores of Yunnan in southern China. This metal was brought by caravan through India into Bactria, a country north of the Hindu-Kush mountains, in what is now known as Russian Turkestan. The earliest specimen extant is a Bactrian coin attributed to 235 B.C. The rough reddish-white metal was also sent in the form of triangular rings to Canton, where zinc ores were added and the whole smelted to a more malleable alloy, also known later as paktong. This alloy was the forerunner of German-or nickel-silver. Specimens of this alloy, wrought into ornamental candlesticks and boxes, were brought from Canton to Europe by the East India Company in the early days of the China trade. Paktong was highly prized for its beauty as well as its eastern origin in far-away China. By 1760 the unwrought metal was imported into England for domestic manufacture.

Jan 1, 1935

By H. J. McQueen

Pyro-reduction of ores to metal products developed markedly through the industrial revolution into the great depression. Nineteenth century resource and environmental sustainability were haphazardly improved by many process changes, although the motivation was primarily reduction in labor, feed stocks and fuel. Some notable achievements were coke and hot air for blast furnaces (later from waste heat stoves), puddling of wrought iron and steel ingot production with convertors advancing into oxygen use and continuous slab, billet and strip casting. Although advances in one sector were often counteracted by fall-backs in others, there was progress in that the resource consumption and pollution per unit of production was decreased. Improvements in the 2 decades following WW2 were mixed but popular notice of environmental hazards forced governments to legislate pollution controls and initiate steps in resource conservation. The energy crisis of the 1970’s saw an industrial energy-saving campaign and legislation of technology assessment procedures. Up until mid 18th Century, the training of iron masters depended on apprenticeship with some formalized knowledge from medieval books such as those of Biringuccio (1540) and Agricola (1556). The advances were very slow partly due to absence of scientific concepts of the smelting process. Nevertheless, some iron masters succeeded in improving the process and described procedures to instruct others. With the surge of steam power and the reverberatory puddling process for ductile wrought iron (WI), machinery changed from wood (iron strap reinforced) to WI machinery. With the clarification of the reduction and oxidation mechanisms by Cavendish and Lavoisier (~1780), productivity in iron production surged. The mechanical testing and microscopy of Kirkaldy (1862) spurred understanding of processing and properties of WI and steel. The various forms of C in steels were determined by chemists at the end of the 19th Century. It also became possible to control metal and slag chemistry in the open hearth furnace. But understanding of the transformations during heat treatment of steel only came in the first decades of the 20th Century.

Jan 1, 2012

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

By J. M. Janssens, Van Quach Tinh, M. Ruel, R. Leblanc

"Microscopic studies of peat moss indicate a highly porous material. In view of using this natural product as an adsorbing agent for the treatment of polluted water, studies of its adsorbing power for beef extract and alkyl benzene sulphonate solution were determined. The effects of time of contact, particle size, concentration of adsorbent and concentration of pollutant were studied. In the case of beef extract, there is a COD reduction of around 27 per cent; in the case of the alkyl benzene sulphonate, the percentage reduction varied from 72 to 95 per cent. A water treatment plant based on the adsorbing power of peat moss with simultaneous recuperation of the pollutant is proposed."

Jan 1, 1971

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By F. F. Langford

"The Athabasca Basin occupies about 100,000 km2 of the northwest corner of Saskatchewan with its western margin extending about 50 km into Alberta (Fig. 1). The basin is filled with a Helikian sequence of predominantly fluvial sandstones up to 1600 m thick. The sandstone beds are generally flat-lying, and rest unconformably on a crystalline basement which consists mostly of granitic intrusive complexes and quartzfeldspar- biotite gneisses. The basement rocks represent Aphebian sediments and Archaean basement rocks that were metamorphosed and remobilized to varying degrees during the Hudsonian Orogeny (ca 1800 Maj.Since 1968, three mining camps and several substantial unconformity-type uranium deposits have been discovered in the area (Figs. 1 and 2). These deposits lie along the unconformity surface, partially enclosed in sandstones, and partially in the basement rocks. The major deposits have elongate, pencil shaped orebodies that are parallel to the strike of underlying graphitic biotite gneisses. The total tonnage of uranium is in the order of 150,000 to 200,000 tonnes and mining grades range from 0.5 to 2.5 per cent U3O8.IntroductionUranium exploration started in Saskatchewan in 1945 when Jolliffe and Murphy headed field parties to investigate uranium occurrences on the north shore of Lake Athabasca (Kupsch, 1978). Their investigation lead to the development of the Beaverlodge camp in the following years. Some of the early prospectors were impressed by the fact that the uranium occurrences at Beaver lodge were centred on a thick sequence of unmetamorphosed arkosic redbeds which are now called the Martin Group. This sequence was referred to as the Athabasca Series by Christie (1949), and although some occurrences of uranium were found near Stony Rapids and Black Lake, the vast expanse of Athabasca sandstones south of Lake Athabasca was generally regarded as unpromising."

Jan 1, 1986

By Jianwen Yang, Yucai Zhou, Yanhong Dong, Daixiong Chen

"The study of combined depressants for flotation separation of lead from copper has been carried out to solve the copper-lead separation problem. Test results show that the depressant of CMC (Carboxyl Methyl Cellulose) or sodium sulfite plays an important role on the selective depression of galena flotation. When the two reagents above are combined, the selective depression effect on galena is further enhanced. When the mass ratio of CMC to sodium sulfite is 1:4, galena was best depressed, with the lowest lead content in the copper concentrateClosed-circuit tests indicate that under a certain pH value of the slurry, with the best ratio of CMC to sodium sulfite as depressants, the copper concentrate with the grade of 28.23% copper and 4.12% lead is obtained, and the copper recovery is 84.87%; the lead concentrate with 68.12% lead and 0.86% copper is obtained, and the lead recovery reaches to 92.20%. An efficient separation of copper and lead is achieved with the combined depressants. INTRODUCTIONComplex copper-lead-zinc sulfide ore is abundant in China. With the rapid increase of mineral consumption, it has become one of the important sources to produce copper-lead-zinc metals. However, it is difficult to achieve effective separation of copper and lead, due to the complicated ore properties, such as fine dissemination, low copper grade, complex symbiotic relationship and similar floatability of copper and lead.Poisonous reagents of bichromate and cyanide are often used as depressants for copper lead separation. They have good separation efficiency, but pose serious pollution issues. As the environmental protection is becoming more and more important, it is a trend to replace traditional toxic reagents with new nontoxic efficient chemicals. Organic depressant FCLS studied by Liu has strong selectivity against galena, and does not depress chalcopyrite. A new type of galena depressant of CLS-01 discovered by Jin-lin Yang shows good results in the separation a mixed copper and lead concentrate. In addition, dextrin, chitosan and some other natural organic compounds (Drzymala, 2003; Huang, 2012; Qin, 2013) have also been studied to separate copper and lead."

Jan 1, 2016

By W. S. Dyer

The lignite deposit at Onakawana on the Abitibi river is of particular interest at the present time, since the Ontario Government has recently decided to proceed with the extension of the Temiskaming and Northern Ontario railway to James bay. Forty-five miles of steel will be laid this year to the crossing of the Moose river. This will cross the lignite field. It has been known for many years that lignite occurred in the Moose River basin, but it was not until drilling was commenced at Blacksmith rapids (or Onakawana, as the camp is now known) in June, 1929, that a seam of economic thickness and extent was found. Early in 1929 the Ontario Legislature voted $25,000 for the carrying out of a drilling programme in the Moose River basin. This came as a culmination of two summers' exploratory work by the Geological Branch of the Ontario Department of Mines, and as the result of a report which said; in effect, that further information concerning the mineral resources of the basin could only be obtained by drilling, and that such a drilling programme was well worth while in order to establish once for all whether lignite, fire-clay, or oil or gas did or did not exist in economic quantities in the region.

Jan 1, 1930

By A. Aubin, H. Yang, G. Zaluski

The Athabasca Basin of northern Saskatchewan and Alberta is an exceptionally rich metallogenic region, hosting more than 2.8 B lb U3O8, of which over 927 M lb U3O8 have been mined out since extraction first started in the late 1970’s. A detailed compilation of several empirical features of 85 deposits located within the basin was conducted in order to understand the distribution and variability of the geological characteristics of the mineralization and its associated alteration. A new empirical classification was devised based on four parameters: 1) geometry of the mineralization (dimensions and relation to the unconformity surface), 2) size, grade and metallurgical complexity of the mineralization, 3) lithostructural setting, and 4) extent and nature of associated alteration haloes. This compilation defines the footprint characteristics of the Athabasca Basin deposits, which guides decision-making processes from early exploration and discovery to resource expansion and extraction.

Jan 1, 2020

By David S. Wong

With air emission limits for total particulates continually tightening, management of `potroom dust' or airborne particulates from aluminium smelting potrooms is of increasing importance. To better understand how settled and airborne particulates are generated within a potroom, methodologies have been developed to sample and analyse the compositional signature of dust, in relation to its sources. During a smelter case study, these methods allowed tracking of mineralogical phases in dust across a range of potroom locations, showing that the mechanisms of dust generation do vary spatially and vertically in a potroom. Such methodologies may also be applicable to other metallurgical industries.

Jan 1, 2011

By C. G. McLachlan

Abstract This paper deals with the application of the cyanide process to recover gold from a pyrite concentrate produced by means of differential flotation. This concentrate before cyanidation contains from 0.09 oz. to 0.14 oz. gold per ton, of which only about 60 per cent is recoverable. The rest is so fine that it remains interlocked in the pyrite and therefore is not acted on by the cyanide. The concentrate also contains about 15 per cent pyrrhotite and 0.4 per cent chalcopyrite, both of which are cyanicides. The cyanicidal effect of the pyrrhotite is inhibited by preacracing the pulp with lime, and maintaining a high lime alkalinity during cyanidation. The effect of the chalcopyrice is reduced as far as possible by removing those particles which are free by means of a further flotation step immediately prior to cyanidation. This involves the flotation of some very fine material. After nullifying as far as possible these two cyanicides, the concentrate is cyanided directly, i.e., without being roasted. This leaves the pyrite available for subsequent sale as a source of sulphur dioxide and sulphuric acid, and the entire residue of the cyamde plant, amounting to about 500 tons per day, 1s now being disposed of in this way. Prior to deciding on direct cyanidation, a number of laboratory roasting tests were made. These showed chat, 1f proper control were exercised, a better recovery of gold could be effected from the roasted product than by the direct method of treatment. The tests also showed that the capital cost o the plant would be much higher than that needed for the procedure adopted. The possibility of subsequently selling the pyrite for its sulphur content would also have been eliminated. Introduction A previous paper has described in considerable detail the application of the flotation process to improve gold recovery from Noranda's milling ore, and in so doing has covered the production of an auriferous pyrite concentrate. The present paper deals with the recovery of gold by cyanidation from that concentrate. This gold, though intimately associated with the pyrite, can, for metallurgical purposes, be considered as all occuring in the native state.

Jan 1, 1946

"Load-haul-dump machines (LHDs) are typically used in underground metal mining operations. Delays or inappropriate use of LHDs can result in production loss. Optimized LHD use is especially crucial in larger mines because longer travel distances increase heat, dust, and gas emissions, which in turn increase ventilation costs. This study, conducted at an existing Swedish sublevel cave underground mine, used discrete event simulation and the AutoMod™ DES tool to determine the ventilation costs related to using too many diesel LHDs in a production area with reduced ore pass availability. When fewer ore passes are available, ventilation costs related to operating LHDs in the production area were found to increase by as much as 200, 224, and 306% for one, three, and six LHDs in operation, respectively. ¦ KEYWORDS Discrete event simulation (DES), Loading operations, Production rate, Ventilation costs RÉSUMÉ Dans les exploitations souterraines d’extraction des métaux, on utilise généralement des chargeurs-transporteurs (LHD, de l’anglais Load-haul-dump machines). Les retards ou l’utilisation abusive des LHD peuvent entraîner une perte de production. L’utilisation optimisée des LHD est particulièrement importante dans les grandes mines en raison des longues distances parcourues, lesquelles augmentent la chaleur, la poussière et les émissions de gaz qui, à leur tour, décuplent les coûts de l’aérage. Cette étude, menée en Suède dans une mine souterraine utilisant la méthode d’exploitation en sous étages avec foudroyage, s’est basée sur la simulation à événements discrets (SED) et l’outil de SED AutoMod™ pour déterminer les coûts de l’aérage liés à l’utilisation d’un nombre trop élevé de LHD alimentés au diesel dans la zone de production, avec une disponibilité réduite de la cheminée à minerai. Lorsque les mines disposent de moins de cheminées à minerai, l’étude montre que les coûts de l’aérage liés à l’exploitation des LHD dans la zone de production augmentent respectivement de 200, 224 et 306 % pour un, trois et six LHD en fonctionnement. ¦ MOTS CLÉS coûts de l’aérage, opérations de chargement, simulation à événements discrets (SED), taux de productionINTRODUCTION Transporting material from the mine face to the dumping location requires flexible loading and hauling equipment that is able to cope with sharp curves and a complex mining environment. Load-haul-dump machines (LHDs) are designed for such an environment. Models are available to suit specific features of the working environment such as small, large, or narrow open stopes (Atlas Copco Rock Drills AB, 2007). When carrying a full load, haulage speed is higher for LHDs than for front-end loaders with the same engine size. Also, payloads are approximately 50% higher for LHDs than for front-end loaders (Atlas Copco Rock Drills AB, 2007). LHDs are capable of climbing steep (Bloss, Harvey, Grant, & Routley, 2011). The haulage distance between stope and ore pass is usually between 50 m and 400 m. LHDs are efficient for tramming distances up to 200 m (Bloss et al., 2011), whereas when loading trucks, the LHDs work efficiently when the distance is less than 100 m (Atlas Copco Rock Drills AB, 2007). The largest diesel-powered LHDs, with drive motors of up to 350 kW, can handle a payload of 21 t (Wennmohs, 2014). Most mining equipment runs on diesel fuel, which provides flexibility, high durability, and high efficiency (Pronk, Coble, & Stewart, 2009); however, other alternatives such as electric, hybrid diesel/electric, or hydrogen fuel cell machines are increasingly being developed and used. This change is due to diesel-powered machines accounting for a significant portion of the ventilation costs in the mine (Chadwick, 2008; Paraszczak, Laflamme, & Fytas, 2013). Currently, as part of the European sustainable intelligent mining systems (SIMS) project, Epiroc AB is planning to demonstrate technology for a diesel-free underground mine at Agnico Eagle’s Kittlä mine in Finland using"

Jan 1, 2019

By James H. C. Martens

Among the many interesting problems of the pre-Cambrian of the Canadian Shield is that of the origin of certain types of gneisses which are intimately associated with the granites on the one hand and with the metamorphic rocks of known sedimentary origin on the other. The observations recorded in this paper on the structure and composition of these ancient rocks found in a small part of northern Quebec may help to lead to a clearer understanding of the way in which they were formed and also constitute a contribution to the regional geology and petrography of a district for which little detailed information is available. The area considered is located near the Ashuapmuchuan, or Chamuchuan, river about 180 miles north-northwest of the city of Quebec, and therefore well within the Canadian Shield. Although most attention was devoted to the rocks along this river from the 57th to the 70th mile above its entrance into Lake St. John, a few observations on other localities to the north and northwest of that lake will be included. The field work was done in the summer of 1924 in cooperation with L. W. MacNaughton, E. S. Roberts, and B. M. Shaub, all of Cornell University. The party ascended the Ashuapmuchuan river by canoe and spent about a month near the mouth of Stacker, or Brochet, river, the outlet of the lake of the same name, returning by way of Mikoasas river. The writer wishes to express his obligation to his associates for their co-operation in the field and for their permission to publish the results. He is especially indebted to B. M. Shaub for the photographs of rock outcrops. Professor A. C. Gill g:ive many suggestions which were helpful in the laboratory study of specimens and in the preparation of this paper.

Jan 1, 1927

By J. R. Rodda

Stainless steels are widely used to handle concentrated sulphuric acid (H2SO4) solutions produced in the manufacturing process, The majority of corrosion rate data published for stainless steel in product acid conditions is typically complied in tables or in iso-corrosion diagrams (iso-corrosion rates plotted as a function of temperature and H2SO4 concentration), without any reported consideration as to the accuracy and relevance of the method used to obtain the data, Given the characteristic potential cycling associated with the active-passive corrosion behaviour exhibited by stainless steel in hot, concentrated H2SO4, weight loss is considered to be a more reliable method than electrochemical measurements to measure corrosion rates, Consequently, an effort is made herein to demonstrate the accuracy and relevance of weight loss to determine laboratory corrosion rates in product acid conditions.

Jan 1, 2010

By M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9 m × 2.05 m AG mills (fixed speed) are used in parallel in a dry operation. The performance of AG mills has been lower than the target value indicated by an increase in the product size (P80) from 450 µm (target) to 515 µm and low power draw (50% of nominal). By simulation it was found that increasing the liner lifter face angle from 7 to 30o while keeping the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. When the proposed liners installed in one of the AG mills, the throughput increased by 27%; when 5% (v/v) balls were added the throughput increased by 40%. The product size also decreased from 515 to 501 µm.

Jan 1, 2012

By Yongjie Bu, Wei Sun, Zhiyong Gao, Yuehua Hu, Hongbiao Tao, Runqing Liu, Central South University

"The flotation behavior of O-isopropyl-N-ethyl thionocarbamate (IPETC) and pH for chalcopyrite and galena was studied through pure mineral test, adsorption quantity determination, solution chemistry calculation and Materials Studio simulation. The results show that the recovery differential value of chalcopyrite and galena is about 20% when pH of the pulp 9.5 and IPETC is 7×10-4 mol/L, the flotability differences of the two minerals is significant. There is competitive adsorption between OH? and IPETC on mineral surfaces, it lead to galena flotability is lower than chalcopyrite flotability. IPETC can remove the hydration layer on mineral surface and adsorb on active sites for collector adsorption, minerals have a better hydrophobicity.INTRODUCTIONCopper and lead are two of the most widely used metals in industrial and living, their applications include building construction, various metal alloys, heat and electricity, machine manufacturing (Zhang et al., 2014). Chalcopyrite and galena are the major source of copper and lead, normally they associated with each other. With the growing use of these resources, high grade and dissemination large particle sizes minerals are less and less, the use of low grade and complex dissemination minerals have to be paid more attention (Chen, Ye, & Li, 2010; Liu, Sun, Hu, & Wang, 2009). As the special properties and complex composition of copper-lead sulfide ore, flotation separation of chalcopyrite from galena effective is a research emphasis and difficulty point in mineral processing (Bruckard, Sparrow, & Woodcock, 2011).In the separation process of chalcopyrite and galena, it is rather important to choose effective collector (Huang, Wang, & Liu, 2014). Enlarging and using the two mineral flotability will be a good basis and start in flotation (Reyes-Bozo et al., 2014). Qin et al. (2013) made a great deal of research on flotation separation of copper/lead concentrate, collector O-isopropyl-N-ethyl thionocarbamate (IPETC), butyl xanthate (BX) and ammonium dibutyl dithiophosphate (ADTP) were investigated, BX and ADTP floated both chalcopyrite and galena well, specific adsorption appeared in the surface of mineral, the problem was the collectors were not selective enough, however IPETC showed better selective."

Jan 1, 2016