Search Documents

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

By G. R. Guillet

THE LATE Dr. D. F. Hewitt, Ontario's foremost authority on industrial minerals, was the first to point out the importance of urban minerals when he produced figures (Hewitt 1968) to prove that the Toronto-Hamilton area was Ontario's second largest mining camp in 1966 (Fig . 1). In that year, the value of mineral production within a 60-mile radius of downtown Toronto exceeded individually that of Steep Rock, Kirkland Lake, Timmins, Manitouwadge and Elliott Lake. Only the nickel and precious-metal production of Sudbury .surpassed in value that of Toronto's pits and quarries. Although that position was unchanged for some years during the early sixties, it was admittedly an unusual situation: gold was still pegged at an artificially low value; uranium was stagnant; and Texasgulf had not entered the scene. However, the point had dramatically been made. The combined value of production from hundreds of sand and gravel pits and dozens of limestone and shale quarries was of formidable proportions. The mining industry of the urban fringe could not be denied. Construction aggregates, cement, building stone and bricks were fueling an apparently insatiable appetite for urban expansion and redevelopment.

Jan 1, 1978

By C. E. Cairnes

The Slocan mining camp in Kootenay district; British Columbia; has long been noted for the great number of its silver-bearing deposits; and for the success that has; in many instances; attended their development. The orebearing area lies east of Slocan lake and mainly within a radius of 6 to 8 miles of the mining town of Sandon. Within this limited area 135 or more properties have shipped ore in quantities of from 100 tons or less to more than 500; 000 tons; and with a total value in silver; lead; and zinc ranging from a few hundred dollars to well over $10; 000; 000. Of the three metals; silver has easily ranked first in value; with lead second and zinc third. Zinc production; however; made slow progress in the early years; and with . the exception of the Lucky Jim mine; and a few others where high-grade ore could be readily hand-sorted; was a detriment to the silver-lead ores until improved methods of separation enabled it to take an important place in the mineral production of the Slocan.

Jan 1, 1954

By Keith Haddock

"The Sheerness Mine, a new surface coal mine located near Hanna, Alberta, went into full production in mid-1995. The mine, which is operated by Luscar’s subsidiary Forestburg Collieries (1984) Ltd., has the design capacity to supply up to 2.1 million tonnes of sub-bituminous coal per year to the adjacent Sheerness Generating station under a 30-year contract. This paper documents the construction phase of this project and highlights the major equipment purchases as well as the construction of the mine facilities. The paper also focuses on some of the areas where cost savings have been achieved that have allowed the mine to come on stream six months ahead of schedule, and under budget. Project ReviewMine DescriptionThe Sheerness Mine is located 25 km southeast of the town of Hanna in southeastern Alberta (Fig. 1). The mining property occupies the western portion of the Sheerness CoalField and borders the Montgomery Mine, operated by Manalta Coal Ltd. in the east, and Highway 36 in the west. The Montgomery Mine and the Sheerness Mine exclusively supply the total coal requirement of the adjacent Sheerness Generating Station. The station is owned jointly by Alberta Power Limited (APL) and TransAlta Utilities Corporation (TAU). APL is the operator. Manalta’s Montgomery Mine has supplied coal to the Sheerness Station since its opening in 1986. Coal is shipped by truck from the mines over a network of haul roads to the coal receiving hoppers located on the east side of Highway 36."

Jan 1, 1997

By Y. Zedan

Cutting fluids play important roles during machining, including the reduction of friction and temperature. Using a cutting fluid, however, degrades the quality of the environment and increases machining costs. The aim of the present research work is to study the effect of cutting fluids and their interactions with cutting parameters on the quality of holes during the drilling of 6061-T6 aluminum alloys. The lubrication types and modes investigated are dry machining, flood lubricant machining and minimum quantity lubrication machining (MQL), while the part quality criteria include the surface finish, the dimensional accuracy, and burr forms and sizes. A scanning electron microscope (SEM) was used to investigate the formation of built-up edges (BUE) in the drill flutes as well as the surface texture of drilled holes. It was found that dry machining and MQL machining can produce parts having quality levels comparable to those obtained in wet machining, when using the optimal cutting conditions.

Jan 1, 2011

By L. B. Smith

Introduction The property of Wright-Hargreaves Mines, Limited is situated at the northeastern end of Kirkland lake, Ontario. It lies immediately east of the Lake Shore mine, and about in the centre of the Kirkland Lake camp. The district is served by the Swastika-Rouyn branch of the Temiskaming & Northern Ontario railway, the town of Kirkland Lake being four miles northeast of Swastika, which is 63 miles north of Cobalt and 392 miles north of Toronto. The mine is developed by three shafts and has more than twenty-eight miles of underground workings. There are two main producing veins, which lie in a porphyry boss 1,350 feet wide. Milling started in May, 1921, and to-date (January, 1933) the mine has produced gold to the value of $21,770,183. Present production is at the rate of 800 tons of ore per day. For a description of the geology, reference may be made to the report by E. W. Todd on the Kirkland Lake Gold Area (1). Structure and Ore Deposits The two major productive veins on the Wright-Hargreaves property are known as the North vein and the South vein. In the vicinity of the shafts these veins are approximately 550 feet apart. A third vein, known as the Inclined vein, has been worked from its junction with the South vein at the 2,000-foot level to its intersection with the North vein at the 800-foot level. This inclined vein has to date been found only in the area east of the eastern major north-south fault. The main North vein and South vein have a general vertical dip, although local rolls and post-ore faults throw certain sections out of line. From the surface to 3,900 feet, the North vein is displaced south less than 200 feet, and the South vein at the same horizon is almost perpendicularly beneath the surface showings.

Jan 1, 1934

By L. C. Johnston, J. N. Gills

This paper reviews the basic reactions of the blast furnace and the open hearth furnace, and then discusses the quarrying and sizing requirements of the limestone feed for each. Particular emphasis is placed on the lime-stone at Irish Cove, now being mined under an agreement between Scotia Limestone Limited and Dosco Steel Limited. The drilling and blasting operations are described, along with loading and haulage, plant flow, water supply, power supply and transportation facilities.

Jan 1, 1967

By G. Morin, F. Chiesa, B. Tougas, B. Duchesne, Jocelyn Baril, N. Giguère

"An aluminum A356 compressor impeller was sand cast using the Low Pressure technique. The casting was limited in size (170 mm in diameter, 1.2 kg in weight) and very intricate in shape thus making 3D mold printing particularly favorable; indeed, producing this part by the traditional pattern-core box route would involve mounting 12 cores inside the mold while stringent dimensional tolerances are required as the impeller blades are only 2 mm thick. Consequently the molds were produce on the X-One MFlex printer of Quebec Metallurgy Center - CMQ. A dozen castings were produced with different casting temperatures and filling times so that it was possible to assess under which conditions complete filling of the mold cavity would be achieved. Filling and solidification modeling allowed predicting misruns and metallurgical properties inside the A356 (AlSi7Mg04) casting.INTRODUCTION Recent advancements in additive manufacturing enable foundries to produce molds without the tooling (pattern and core boxes) necessary when conventional technology is used (Eyad, 2016). This is particularly advantageous when dealing with intricate shapes and/or when a limited number of parts must be produced within a few days rather than in 5 weeks. An additional advantage is gained when producing prototypes (Johnson, 2016) as changes are much less costly and time consuming when made on a numerical 3D drawing rather than on patterns and core boxes. 3D printing is normally economical for a small number of parts; however, if the part is not too big and very intricate in shape such as the part that will be studied in the present work, 3D printing can be economical even for an important number of castings to be produced. On the other hand, low pressure casting is a high integrity casting process in which the mold cavity is filled from the bottom via a transfer tube in which the liquid aluminum rises under the pressure applied at the surface of the melt as illustrated in Figure 1. The filling can thus be precisely controlled, eliminating the turbulence created when the mold is filled from the top (gravity casting). Also, the pressure applied on the melt during solidification results in excellent feeding of the casting when conditions of directional solidification are met. In the present work, the compressor impeller shown in Figure 2 will be sand cast by low pressure."

Jan 1, 2018

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017

By A. J. Rigby

Computer generated, actual-scale furnace models have been imported into a rendering software application to provide for impressively realistic surface features and lighting. When these models are imported into a 3D engine framework, it is possible to create content-rich virtual environments allowing for complete interactivity and could provide for a powerful tool to conceptualize refractory lining designs. This technology has been applied to illustrate the optimized design concept of an anode-refining vessel, which can be expected to be completely relined in six days and to last for 4-5 years with minimal partial relining. This technology could easily be applied to other smelter furnace, converter and refining vessel designs.

Jan 1, 2007

By J. M. Cummings

DURING the past year, the writer has investigated the treatment of a variety of British Columbia tungsten-bearing ores. Much of the test-work described in this paper was carried out in collaboration with Mr. A. G. Lyle in association with the British Columbia War Metals Research Board at the University of British Columbia. The remainder was completed in the laboratories of the Department of Mines at Victoria. Two mills in the Province are at present treating tungsten ores. Descriptions of these are included through the co-operation of Messrs. S. Gray (1) and A. A. Almstrom (2). MINERALOGY, OCCURRENCE, AND SPECIFICATIONS In the present paper, attention is directed solely to scheclite, inasmuch as known occurrences of other tungstcn minerals in British Columbia are of mineralogical interest only. The properties of scheclite are listed below: Percent W03 .. 80.6 Tenacity ...... Very brittle Çrystallization Tetragonal Lustre ........ Vitreous to resinous Cleavage ...... Good in 4 directions Magnetism ... Non-magnetic Specifie gravity 6.05 Diaphaneity .. Transparent to translucent Hardness. . . . . . 4.5-5.0 Scheelite may contain as much as ten per cent of molybdenum in solid solution, but most of the specimens from British Columbia examined by the writer were relatively pure.

Jan 1, 1943

By Patty Simpson, Sarah Benson

In an effort to improve consistency across the nuclear industry, over the past 10 years the Canadian Standards Association has developed a series of standards related to environmental management at Class 1 nuclear facilities and uranium mines and mills. Canadian uranium mines have been required by the Canadian Nuclear Safety Commission to align their existing monitoring programs with these standards. Orano’s McClean Lake Operation’s monitoring program, which was originally presented in the Environmental Impact Statement in 1991, has evolved through regulatory change, new scientific understanding, additional projects, and experience into a comprehensive set of monitoring requirements for effluent, groundwater, air emissions, and the receiving environment. The exercise of aligning the existing practices with the standards provided an opportunity to review and rationalize the entire program. To document the process the original “Environmental Monitoring Program Design Document” was restructured and developed as both a repository for historical information and monitoring rationalization, and also to be a living document describing on-going studies and supplementary work that are outside of the regular environmental monitoring program and may justify future changes to the program.

Jan 1, 2020

By C. J. Clayton, A. J. Haynes, D. A. Hickson, B. Thiele

The Meadowbank Gold Project, formerly owned by Cumberland Resources Ltd. and currently owned by Agnico Mines Ltd., is currently being developed approximately 70 km north of Baker Lake, Nunavut, in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of a series of gold-bearing deposits within relatively close proximity to one another, which are planned to be mined primarily as a truck-and-shovel open pit operation using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of eight to ten years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11°C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site and the physical environment pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project. Note that volumes, tonnages, construction concepts, and data presented in this paper are accurate for the time of writing and are subject to change and modification as the project progresses, additional modelling is carried out, and additional data are obtained.

Jan 1, 2007

By James A. Brown, Marius Botha, Christopher A. Fleming

"The technical and economic feasibility or re-processing hundreds of millions of tons of tailings in a number of historic gold tailings dams in the Witwatersrand area of South Africa is being investigated. The objective is to recover uranium and residual gold from the tailings, as well as to oxidize the sulphides to eliminate long term environmental liabilities associated with acid mine drainage. The tailings from the re-processing plant will be re-deposited in a new area far from urbanization, allowing for the rehabilitation of the real estate currently occupied by these historic tailings.The first step in the process involves a mild-regrind and mild acid leach of the tailings (pH 2.5 to 3.0) to dissolve up to 40% of the uranium. This uranium is recovered directly from the pulp by resin in pulp (RIP) with a strong base resin. The RIP tails are then treated by flotation to recover a rougher pyrite concentrate, and flotation tailings that are discarded. The rougher concentrate is cleaned to produce a final pyrite concentrate and cleaner scavenger tailings, and the pyrite concentrate is oxidized in an autoclave to leach uranium and generate acid. The autoclave discharge is combined with the cleaner scavenger tails, and the acid and ferric ions generated in the autoclave are used to leach more uranium and oxidize more sulphide in the cleaner tails. The product from the concentrate leach circuit is processed by resin in pulp for uranium recovery, followed by neutralization, cyanidation and carbon in pulp for gold recovery.The rougher float tails may be further treated to recover gold that was not recovered in flotation, but which had been liberated from the old dumps by natural oxidation of some of the pyrite over many decades. The float tails would be neutralized and treated by cyanidation and CIL to recover this liberated gold.All parts of the flowsheet have been extensively tested in the laboratory, and the critical elements of flotation, pressure oxidation and resin in pulp have been demonstrated in pilot plants. The results of the hydrometallurgical investigations are presented here."

Jan 1, 2010

By J. S. Roper

"IntroductionSNOW LAKE is situated in northern Manitoba at latitude 54° 55 and longitude 100°, 400 miles northwesterly of Winnipeg, 80 miles northeast of The Pas, 80 miles east of Flin Flon. A 38-mile road from Wekusko, on the Hudson's Bay railway, serves the community.The mine is located in and close to the southern edge of the Precambrian Shield in typical low-relief muskeg and lake country.The Howe Sound Exploration Company, Limited optioned the property from Nor Acme Gold Mines, Limited, after preliminary diamond drilling had outlined two orebodies of low-grade arsenical gold ore.Following the examination and study of geological data and of 50,000 feet of diamond-drill core, and metallurgical tests made during 1942 to 1945, a decision was made to develop the mine and build a 2 ,000-ton mill concurrently. This development has been described by G. C. Lipsey in a paper entitled The Development of a Mining Operation from Diamond-Drill Data which was published in the August. 1952, issue of Mining Engineering.Geological Features of the OrebodiesThe orebodies at Snow Lake occur in volcanic rocks of acid to basic composition and, to a lesser extent, in intrusive hornblendite. The hornblendite is a massive, uniform, .coarse-textured rock except in the immediate vicinity of the ore zone, where it becomes sheared and carbonatized. The acid volcanics have been converted to quartz-garnet-biotite gneiss, and the basic volcanics to amphibolite gneiss. Orebodies have been formed by the replacement of all three rock types."

Jan 1, 1955

By C. E. Lancelle, J. T. Volk, H. F. Wang, D. Fratta

"The Main Injector Neutrino Oscillation Search (MINOS) Near Detector Hall at Fermilab and the Lafarge – Conco Mine are located approximately 100 meters underground in the Galena-Platteville dolomite just below its contact with the overlying Maquoketa shale in Northeastern Illinois, USA. A new cavern was excavated adjacent to the MINOS Near Detector Hall at Fermilab to house the near detector for the Off-axis Neutrino Appearance Experiment (NOvA) program. During this excavation approximately 1150 cubic meters of shale rock were removed. Tiltmeter arrays consisting of a series of hydrostatic leveling sensors (HLS), which are spaced regularly over a total distance of 50-to-100 meters, were used to monitor subsurface deformations. The tiltmeter response in the MINOS Near Detector Hall due to the NOvA cavern excavation is approximately thirteen times the estimated response based on using laboratorydetermined properties. The discrepancy between modeled and measured tilt is likely due to differences in Young’s Modulus in the rock mass versus in a small laboratory sample. Amplitudes of measured solid earth tides differ from the amplitudes of theoretical solid earth tides by up to 40 percent for both arrays. This is likely due to a local heterogeneity or discontinuity.INTRODUCTIONLong baseline tiltmeters have been used to record small earth movements since the early 1900s. One of the first studies using long baseline tiltmeters to measure earth tides was published by Michelson (1914). He used a leveled 152-meter long, 0.15-meter diameter tube half-filled with water connecting two concrete-lined pits. The pipe was trenched 1.75 meters underground in Williams Bay, Wisconsin in a sandy-clay soil. Initially only an east-west line was used, though a north-south line was added after it was seen that viable results were obtained. Measurements were made by hand either hourly or once every two hours depending on the time of day. When compared to 0.7 times the calculated earth tides, the tiltmeter signal matched almost exactly. This excellent result began the use of long baseline tiltmeters to measure small earth movements."

Jan 1, 2015

By Francis Breton, Daniel Larouche, Pierre Heugue, Rémi Martinez

"Nowadays, in order to fit environmental restrictions, automotive markets are demanding cast aluminum alloys working at high temperature (180–300°C). New generations of alloys are required for higher strength components in engine downsizing or start-stop systems which lead to higher loading and higher specific power and stretch current materials to their limits. Recently, transition metals, such as zirconium and vanadium, have been added as alloying elements into an AlSi7Cu3.5Mg0.1 alloy to improve physical, mechanical, thermodynamic properties with the aim of increasing service life of parts. In such alloys, the best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, including: solutionizing, quenching and artificial aging. This study is focused on the modified AlSi7Cu3.5Mg0.1 cast alloy with Mn, Zr and V additions for high temperature application. The characterization of the cast alloy in this study, firstly, helps to evaluate and understand its performance both chemically and structurally according to their physical state: as-cast or as-quenched. Comparison of precipitation kinetics between a binary Al-3.5%wt.Cu alloy and the AlSi7Cu3.5Mg0.1 (Mn, Zr, V) alloy has been characterized by differential scanning calorimetry, TEM observations and micro-hardness testing. The Kissinger analysis was applied to extract activation energies from non-isothermal DSC runs conducted at different stationary heating rates. The study focuses on the impact of the chemical composition such as Si content on the kinetics parameters.INTRODUCTION Pure metal Aluminum shows poor mechanical properties and its malleability is high, that is why alloying elements are added to the mixture before casting to improve physical, mechanical and thermodynamic properties (Javidani, 2015); such as Silicon (Si) for casting properties (castability, cold crack capability, wear resistance, shrinkage behavior), Magnesium (Mg) and Copper (Cu) to generate precipitation hardening systems. Aluminum hypoeutectic alloys (<12% Silicon) with Cu, Mg additions used in the automotive industry for manufacturing mechanical parts (Larouche & Javidani, 2014) are mostly subject, after casting, to precipitation hardening heat treatment (Mohamed & Samuel, 2012) according to specifications and associated standards. The best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, generally including: solutionizing, water quenching and artificial aging (Manente & Timelli, 2011). Hypoeutectic aluminum-copper alloy with amount of Cu around 1 to 4.5wt% is an elementary case for precipitation in heat treatable aluminum alloys. Researchers essentially focused their work on the full precipitation sequence of binary Al-Cu alloy during aging which is presented below."

Jan 1, 2018

By Charle Pelley, Kosta Fytas, Peter Calder

"A computer model has been developed which is capable of evaluating alternative production schedules (long- and short range) of an open pit mine once the ultimate pit limits have been defined. The model user can choose the best alternative according to cash flow considerations and the particular mining conditions. The model involves a combination of simulation for long range production scheduling and linear programming for short range scheduling. IntroductionMining of mineral deposits in such a fashion so that, at depletion the maximum possible profit is realized, has been a very old problem of the mineral industry. In the past, when high-grade ore reserves were readily available and profits were very high, no question of optimum profitability was raised.However, recently the complexity of both open pit and underground mining has been increased tremendously. The additional problems of continuously rising production costs on one hand and of depressed metal prices worldwide on the other, have been demanding optimum profitabiliy from every mining venture .Particularly in the area of open pit mining, the sequence of ore and waste extraction has now become very important since the size of the pits and of the mining equipment has increased enormously. The process of open pit mining involves a continuous change of the open pit surface and there are many feasible plans of extraction which lead to the same final pit shape (ultimate pit limits). Each of these feasible plans generates a production schedule over the entire mine life, which mayor may not be optimal."

Jan 1, 1987

By J. J. Jonas, G. R. Stewart, A. M. Elwazri

Two important parameters for dynamic recrystallization can be derived from the changes in the strain hardening rate: the critical strain for initiation of dynamic recrystallization and the point of maximum softening. In this work, these values are determined from the flow stress-strain data obtained in continuous compression testing in the range 900-1100°C. The resulting strains are used to calculate a kinetic model of dynamic recrystallization for two materials: 304 austenitic stainless steel and a hypereutectoid plain carbon steel. The mechanical parameters used to define the proposed model are confirmed with quantitative metallographic analysis of the recrystallized microstructure.

Jan 1, 2004