Search Documents

By Jeffrey D. Oke

While significant progress in underground construction engineering has occurred in the past few decades, a number of fundamental deficiencies persist regarding the recognition, prediction, and mitigation of underground construction hazards associated with complex geological conditions in rock and soil works, such as tunnelling. Many of these shortcomings could be addressed by improving geomechanical models which, in turn, would provide more realistic frameworks for determining input parameters for design analysis. This would improve predictions of construction efficiency for tunnelling and the formulation of more accurate modelling techniques (2D, 3D and 4D) required to optimize the design of engineered rock structures. This research focuses primarily on the issues related to forepole temporary tunnel support within weak rock masses. This research attempts to determine how best to numerically model forepole support. The behaviour and mechanics of forepole support has not been quantified and/or optimized. As well, there is a lack of in-situ and/or laboratory forepole and weak rockmass interaction parameters available. In terms of numerical modelling, there is a lack of understanding of the use of proper interaction parameters associated with the forepole and the rockmass. The parametric study that has been conducted by the authors demonstrates the influence of each of the forepole-rockmass interaction parameters and their sensitivity. Introduction

Jun 1, 2012

By V. E. Dawson

Brake testing of large mining trucks was initiated in British. Columbia in 1969 following an accident involving the failure of the service brakes of a l00-ton electric-drive truck. Some selected results of the 1976 brake test program are presented and discussed ?in this paper . The tests were conducted on end- dump trucks having load capacities ranging from 85 to 235 tons. All tests were made with the vehicles fully loaded operating on downhill grades varying from 8 to 10 %. Stopping distances were measured from initial speeds varying between 10 and 39 mph. The results are adequate, in most cases, to determine the "ultimate" capabilities of the service brakes of varying models and sizes of haulage trucks operating in British Columbia mines.

Jan 1, 1977

ABSTRACT The inevitable uncertainty in modelling spatial variables decreases as more data become available. This reduction depends on the properties of the variable being modelled. Spatially continuous variables show less uncertainty for a given spacing than erratic variables. A geostatistical simulation based approach is developed to quantify the relationship between uncertainty and data spacing. Reference realizations are sampled to condition additional realizations and quantify uncertainty. The procedure is automated, making it straightforward to consider sensitivity and different geological domains. A case study of the relationship between uncertainty and data spacing for net oil sands thickness data from northern Alberta is presented. _ KEYWORDS Simulation, Sampling,

Jan 1, 2013

By C. Dirscherl, M. Combes

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications.INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment)"

Jan 1, 2014

To determine the optimal circuit configuration for gravity gold recovery consideration should be given to a range of factors in addition to the efficiency of the gravity circuit, including capital costs, ease of operation and impact on comminution. The most common gravity gold circuits utilise a centrifugal concentrator treating a portion of the hydrocyclone underflow. This paper will examine this option and alternative circuit configurations to illustrate the effect of various gravity circuit feed and tailings configurations on the equipment sizing, capital costs, operating costs, water balance, comminution efficiency and gravity gold recovery. The optimum circuit configuration can provide reduced capital and operating costs, maximise gravity gold recovery and improve comminution efficiency.

Jan 1, 2011

By E. Y. Carlson

"IN A SHORT PAPER it is impossible to do much more than to list the industrial minerals found in Saskatchewan and to give a brief description of the activity associated with each. I will not attempt to discuss the geology. It is sufficient to say that the settled part of the Province is covered by glacial drift which varies in thickness from a few feet to several hundreds of feet, and that this has hindered the search over much of the Province.CLAYA notable exception to this is the Cypress Hills area in the southwest corner which did not suffer any glacial action and where we find some of the large exposures of Cretaceous clays. In this area, the majority of the deposits are of stone-ware clays which are •an excellent raw material for such products as face brick and sewer pipe. Although the clay cannot be transported over any great distance it is used extensively in Alberta and Saskatchewan in the production of these products."

Jan 1, 1959

By G. H. Montgomery

THE PROPERTY of Aunor Gold Mines, Limited, consists of eleven claims, located in Deloro township, approximately three miles southeast of the town of Timmins. Production began in 1940 and currently the mine is operating at a rate of 485 tons per day. GEOLOGY AND MINE DEVELOPMENT The ore zone at Aunor occurs in altered lavas bounded on either side by soft talc-chlorite schist, locally known as 'soapstone'. The zone has a strike of N.80°E, dips 60° North, and varies in width from 0 to 250 feet. Within this zone the main orebody has a westerly plunge, away from the No. 1 shaft area (Figure 1). The mine is developed by a vertical three-compartment shaft from surface to the 3,082-foot horizon. Working levels are spaced at 125- foot intervals from the 625-foot to the 1,625-foot horizon, from which to tl1e 2,125-foot level the interval is 250 feet.

Jan 1, 1957

By C. Lapointe

"IntroductionTen years ago, when nuclear fission became practical, the element uranium, until then a not very desirable by-.product of the radium industry, became overnight the strategic material par excellence. One of the several important problems that had to be solved at that time was the rapid and precise determination of uranium in ores and concentrates.GeneralThe chemical analysis of uranium ores is a long and difficult business and is complicated by the presence in most ores of a large number of interfering elements. True, much progress has been made, during the past few years, toward simplification of the analytical methods, but the chemical determination still remains the job of a skilled operator. For this reason, the chemical method has been replaced, whenever possible, by a physical determination based on the measurement of the radiations emitted by the elements of the uranium family. There are several types of instruments suitable for these measurements, but of all the radiation detectors known to the physicist, such as ionization chambers, crystal detectors, scintillation, proportional counters, and the like, the Geiger-Mueller counters have proved to be the most satisfactory for routine determinations, because of their simplicity.The Geiger-Mueller counter is a very versatile instrument; it can be constructed to detect any type of radiation, corpuscular -0r electromagnetic. Here, however, we are interested in these counters because of their ability to detect the beta and the gamma radiations, both emitted by some members of the uranium family. The beta radiation is corpuscular, and is composed of fast electrons, while the gamma radiation is electromagnetic."

Jan 1, 1950

By Al Holmes

"In a recent survey of Canadian work values, 89% of the men surveyed and 97% of the women surveyed described the work in a mine as ""not at all auraetive"", Work in a mine, in fact, was rated by both sexes as the least attractive of all of the types of work surveyed. Confronted with this prevailing attitude, Canada's mining industry starts out with two strikes against it in its bid to attract and hold on to its fair share of available work force.Behavioural scientists have, for decades, been seeking answers to the questions:• ""Why do people work?""• ""Why do people choose a particular occupation?""• ""Why do people choose a particular organization?""• ""Why do people leave one organization for another?""• ""Why do some people stay in an organization?""• ""Why do some people work harder than others?""Their answers to these questions, although tentative and often contradictory, are being used by more and more organizations to solve people problems. Few industries can afford to ignore them, least of all, perhaps, the mining industry.Consider the following developments:I. General Motors and the United Auto Workers turn around the car assembly plant in Tarrytown, New York in seven years from the plant with the poorest labour relations and production record to one of the best under a program referred to as ""improving the quality of work life.""2. Shell Canada and the Oil, Chemical and Atomic Workers have designed a new petro-chemical processing plant in Sarnia using a set of principles that seek to optimize both the social and the technical system."

Jan 1, 1980

By J. Zachwieja

As part of a general review on study of surfactant blinding agents to improve gold recovery during cyanide leaching of carbonaceous gold ores, processes of CIL and RIL leaching using surfactants were investigated. When refractory ores were treated by surfactants, CIL and RIL leaching processes yielded significant improvement on gold recovery. This paper will discuss and compare the laboratory results from two different leaching processes on preg-robbing ores, as well as, illustrate the difference of potential fouling of the blinding agents on activated carbon and resins.

Jan 1, 2015

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

By Zolfan F. Oszter

As exploration for new mineral deposits advances farther into the Canadian North, the more the design engineer is faced with the problems of cold weather conditions. This is especially true when designing belt conveyor systems for open-pit operations where the temperature in the winter may go to -40°F or below. Problems with the mechanical components and also with the belting will arise, which in turn may reduce the availability of the system. This paper outlines the problems encountered during cold weather operation and what precautionary measures must be taken into consideration in the design of equipment, as well as in the selection of materials, in order to ensure a system which will maintain production. THE conveying of ore and waste in the pit or to the processing plant poses problems during cold weather, when temperatures may drop to -4o?F or be-low. Troubles with the mechanical components, the belting or the supporting structure may arise, and this, in turn, will reduce the availability of the conveying system.

Jan 1, 1965

By D. Pacey

"This paper reviews the installation, start-up, and operation of a comprehensive monitoring and targeting management technique in which all plant utilities (i.e., electricity, natural gas, compressed air, and water) are managed as controllable resources in the same way that raw materials, mined ore, personnel and capital are managed.The essential elements of monitoring and targeting (M&T) include:•gathering in a systematic, disciplined way the utility information by energy account centres;•closely monitoring the utilities used in each centre and comparing them with production on a common time base (e.g., kWh/ton per day);•bench marking and target setting to pro-vide attainable energy reduction goals which can be further refined as they are achieved; and•establishing an implementation plant that may provide efficiency enhancing benefits to various operating areas within the plant.The M&T system will reduce utility consumption per unit of production on a continuing basis.This would translate into sustained operating cost and waste. M&T will also provide better information for assessing the plant operation and progressively implementing further enhancements."

Jan 1, 1997

By M. J. Gagnon

The agglomeration of particulate materials is used in many mineral processes to enhance the settling of the fine particles, Depending upon many physical and chemical parameters, the aggregates demonstrate specific density-size distributions, In this study, a fractal model of the agglomeration process is introduced, Based on reliable experimental data and on physical calculation, the model presented helps to envisage the initial formation of the micro-flocs, and to interpret the subsequent interactions between the aggregates in terms of either coagulation or flocculation, Data from different sources, materials and different agglomeration processes are analysed and compared in the light of the proposed model.

Jan 1, 2005

By James F. Archibald

A research effort has been undertaken, under WSIB sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials (TSL?s), typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and boltand- mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen?s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. Both conventional and innovative TSL-type surface lining materials were subjected to ?rockburst? exposure in rigorously-controlled blast trials. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently-available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validates that thin, sprayon linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

May 1, 2003

By C. Blawert

In previous studies of various HPDC magnesium alloys we found that the corrosion properties of the skin are inferior in comparison to the bulk, However, this is surprising as one would expect better corrosion properties for the finer microstructure of the skin, In a more detailed study using 2 and 6 mm thick sections from HPDC AZ91 step plates, the corrosion results of the original skin, the slightly removed skin and the bulk were compared, Indeed, the corrosion measurements including potentiodynamic polarization, long term polarization resistance measurements and electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin. An explanation for this corrosion behavior was found, on the one hand, in the microstructure concerning especially the amount and distribution of the 13-phase and, on the other hand, in the composition, including the distribution of the most important alloying element Al and of some impurities such as Fe.

Jan 1, 2005

By B. Krysa, J. Qiu

The zinc pressure leach plant at HBM&S's operations is now in its fifteenth year of operation. Current pressure leach operation is steady at a concentrate processing rate of around 26.5 tonnes per hour. A new cellhouse with a design capacity of 124,000 tonnes per annum and the capability of expansion of up to 154,000 tonnes per annum was commissioned in July 2001. The potential to expand the capacity of the pressure leach circuit and associated processes, as well as the purification circuit and casting plant, to meet the maximum capacity of the cellhouse has been investigated. This paper reviews current operation of the zinc plant, as well as the possibility of a capacity increase without major process modifications or major capital expenditures.

Jan 1, 2008

"Each and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Several factors including ore heterogeneity and harsh production environment affect the reproducibility of the reported data. Best practices of metal accounting thus prescribe that production reports be accompanied by measurement quality reports quantifying the reproducibility (a data quality metric often expressed as a relative standard deviation) of each data reported. Ignoring the irreproducibility of measurements may lead to the perception that random errors have been totally eliminated through statistical data reconciliation, which is wrong. This paper aims at explaining the full lifecycle management of reproducibility estimation from the outset at the measurement process to its reporting after having been through the statistical data reconciliation process. Indeed, the reproducibility of reported data can be obtained by performing a sensitivity analysis. Necessary conditions for obtaining a truly representative assessment of measurement reproducibility are stated. Typical levels of measurement reproducibility found in operating flotation plants are also reported. These numbers can be used as benchmarks for reproducibility levels that can be realistically expected.IntroductionEach and every flotation plant must produce daily/weekly/monthly production reports in which metal balances for payable and penalising elements are presented. Such production reports are the most expected output from a metal accounting system (MAS). The duly recurrence of this task combined with an insufficient level of automation has somehow contributed to the misleading perception that it is mainly a clerical work. However, as shown in Figure 1, a MAS encompasses way more than just a reporting system. Acknowledging that the content of production reports indubitably origin from raw measurements has important implications for how both the reports and MAS should be monitored."

Jan 1, 2016

By P. P. Rosario

A research project was conducted at the University of British Columbia (UBC) resulting in the development and evaluation of a novel comminution circuit incorporating autogenous grinding and parallel trains of cone crushers and high-pressure grinding rolls (HPGR). A primary driver for the circuit was to treat ore from deposits with clay and variable hardness. This paper summarizes the unique pilot-plant test program that was developed as a basis for experimental simulation and lists the main findings of the research, including the circuit?s potential operational cost savings compared to a conventional SAG circuit.

Jan 1, 2012

By Ken Musgrave

"A program is described that helps managers and supervisors control maintenance more effectively. Work- order generation, preventive maintenance, repair parts inventory, planning and scheduling, reporting, analyzing costs, printing purchase orders and other functions are covered. Flexibility often permits integration with other programs such as payroll, cost accounting and materials management.The Role of MaintenanceMaintenance provides a service to allow the rest of the operation to do its job effectively. Its success should not be measured by maintenance cost alone, but also by its effectiveness in reducing downtime and maximizing production. It can make sense to spend more maintenance dollars if this results in an even greater contribution from increased production.The Cost of MaintenanceIn mining companies, maintenance costs can be as much as half of operating costs. Maintenance has generally not been given the management attention that an expenditure of this magnitude deserves."

Jan 1, 1986