Search Documents

By George H. Hope, Steve Ciccone

"The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day ice-free shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction.INTRODUCTIONThe Red Dog Mine, which began operations in 1989, is located above the Arctic Circle in Northwest Alaska, approximately 145 km north of Kotzebue (Figure 1). An 80-km road connects the mine site to the DeLong Mountain Transportation System (DMTS) port site. Red Dog is the largest known zinc deposit in the world, with known reserves totalling 94.5M tonnes, and is the largest zinc producer with a concentrate production rate of more than 1.1M t/yr.Open-pit mining is by typical drill, blast and load operation using moderately sized mining equipment. Ore is processed through conventional crushing, grinding, and flotation to produce separate lead and zinc concentrates. Filtered zinc and lead concentrates are trucked year-round to the DMTS port site, where they are stored in two A-frame buildings, 330 and 440 m long. A lightering barge system is used to transfer concentrate from the shallow water load-out to deep-sea vessels anchored approximately two miles offshore. Shipping is limited to a 100-day, ice-free window beginning in early July."

Jan 1, 2003

By G. Hu, P. Chang

"As hydraulic fracturing is forbidden in some countries due to its accompanying environmental pollutions, microwave fracturing was proposed as a substitute technology to enhance coal seam permeability. Its mechanism includes: on the one hand, thermal stress caused by non-uniform microwave heating leads to fracture development in coal body, which increases coal seam permeability for gas; on the other hand, moisture within the coal body that hinders gas desorption and diffusion is removed during this process. To study the effect of moisture content on fracture development under microwave irradiation, high resolution photographs were taken before and after microwave treatment. These photographs were then binarized and skeletonized. Based on the processed photographs, the total area were calculated using ImageJ. The results showed that coal samples with 0% and 25% water saturation have more variation in fracture development as compared to that of samples with 50%, 75% and 100% water saturation. This study can be very useful in gas drainage and gas control in coal mines. INTRODUCTION Coalbed methane (CBM) is a clean energy source as well as a natural hazard to underground mining (Kurnia, Sasmito, & Mujumdar, 2014; Ranathunga, Perera, & Ranjith, 2014). One of the main goals of mine ventilation is diluting methane and removing underground contaminants (Xu, Huang, Nie, Chalmers, & Yang, 2017). Coalbed methane (CBM) has to be extracted prior and during underground mining to avoid methane outburst and explosion accidents. However, with the increase of mining depth, the coal permeability decreases significantly, which makes it hard to extract the methane (Huang, Xu, Hu, Kizil, & Chen, 2018). To enhance the coal seam permeability, many CBM recovery methods have been applied on-site, such as hydraulic fracturing and enhanced coalbed methane (ECBM). However, hydraulic fracturing is restricted due to environmental concerns and ECBM is only suitable for the coal seam with relative large permeability (Bustin, Bustin, Chikatamarla, Downey, & Mansoori, 2016; Huang, Xu, Chen, & Chen, 2018; Huang, Xu, Hu, et al., 2018)."

Jan 1, 2019

By S. Parent, J. -F. Lepage, S. Glover

"Goldcorp – Eleonore’s 7 000 tonnes per day gold mill was started up in October 2014 and achieved commercial production in April 2015. During the first year, operation has faced challenges from grinding, flotation, sulfide cyanidation and tailing filtration to achieve targeted throughput, availability and recovery.The optimization of non-sulfide tails filter cloth lifetime and filter press availability had the most significant impact on ramp-up of both mill throughput and availability. A change in steel ball addition size to the grinding circuit was made to meet the targeted p80 of 65 µm. Various optimization efforts were conducted on the flotation circuit, intended to recover all sulfide-bearing minerals. The goal is to attain the environmental target of 0.12% sulfur in flotation tails (to eliminate acid mine drainage or AMD), while an average of 0.31% sulfur was obtained over the first months of 2015. Collectors, frothers, activators and hydrodynamic parameters were tested to improve the circuit desulfurization efficiency. High sulfide reactivity in pre-oxidation and cyanidation severely impacted dissolved oxygen levels and cyanide consumption. Studies were undertaken to understand the effects of mineralogy, grind size and leach conditions on gold dissolution kinetics and cyanide consumption. Efforts were focused on pre-oxidation to restore dissolved oxygen levels as well as optimizing both lead nitrate addition and pre-oxidation time.INTRODUCTIONGoldcorp Eleonore’s mill commissioning started in September 2014. It was considered to operate the mill at 3 500 tpd during design, as the mine was planning to operate at this throughput for the first year. However, with the stockpile of ore and a higher throughput from the mine, the mill was able to run at higher tonnage than initially anticipated.While increasing tonnage, a few bottlenecks were discovered and overcome in areas such as filtration and cyanide destruction. There were also recovery issues which were addressed in areas such as grind and sulfide leach. This paper focusses on the first complete year of operation ending September 30th 2015. A process description and the flowsheet are presented below and it will then go into detail about operational, metallurgical, mechanical and design issues experienced during the year."

Jan 1, 2016

By F. E. Lathe

The method of feeding blast-furnaces to be described below is simply the application of well-known principles, and an attempt to carry that application to its logical conclusion. It does not involve radical changes in equipment, nor does it require unusual skill on the part of the furnaceman. In fact, much of its value lies in its very simplicity. Before giving details of the method it will be well to consider briefly the conditions under which it was used at the Nickelton plant of the British America Nickel Corporation, in the Sudbury district, before that plant closed down. The Sudbury nickel ore consists chiefly of pentlandite, chalcopyrite and pyrrhotite in a gangue of norite or greenstone. The proportions of sulphide and gangue vary widely in different mines, the former constituting about 45 per cent of the total in the British America sorted ore. The gangue is fairly uniform in analysis, carrying about 55 per cent Si02, 18 per cent A120 3, 13 per cent FeO and smaller quantities of CaO, MgO, Na20 and K20. The ore has been frequently described as refractory, a word which seems suitable when one considers the many unsuccessful attempts to smelt it pyritically, as well as the high percentage of coke normally used at all the plants in the district.

Jan 1, 1925

By Tom Demorest

SMART is an association of mining companies that meet regularly to coordinate the technology development needed by the mining industry. Since 1995, the member companies and institutions have directed research and influenced the manufacturers and suppliers to improve surface mining technology and services. SMART actively supports learning seminars, collaborative research projects, and user groups. Members of SMART include some of the major surface mining companies in North America and Australia. These companies have recognized the value that collaboration can bring to the needs of individual organizations as well as the global mining industry.

May 1, 2009

By D. A. Sloan

"THE FIRST COMMENTATOR that I will call on is Mr. W. G. (Bill) Brissenden, Vice-President, Mines, Noranda Mines Ltd. Bill, would you care to comment.W. G. BRISSENDEN ...Mr. Chairman, Ladies and Gentlemen, I spent some time reading the four papers that were presented here, yesterday evening, and decided that the four to six minutes that I had been allotted for this afternoon were going to be pretty tough to meet. It's a very big subject and I just hope that I will be able to stay within my time limit. As has been so aptly demonstrated by the members of our panel here this afternoon young men in growing numbers continue to be attracted to careers in the mineral industry, especially to careers in mining engineering. Now from 80 the point of view that the profession may have regained its status this is indeed welcome news. However, perhaps all of the members seem to have the suspicion that the number of mining engineers that the industry can absorb is a much lower figure than previously forecast. It is said that technical school graduates are now occupying some of the jobs once considered the private preserve of the mining engineer and also that mining engineering undergraduates are having trouble locating summer employment. If these interpretations of mine are correct then we are now confronted not only with our old dilemma - whither the mining engineer - but also with an urgent need to solve it. We cannot allow our profession to become once again an undesirable one in the eyes of our youth because if we permit such a thing to happen a second time the profession may never recover."

Jan 1, 1972

By R. P. Zahn

The need for quantitative mineralogical data to characterize ore types before they are processed is becoming increasingly necessary. Mineralogical data (modal abundances, grain size, liberation/locking characteristics, mineral textures and associations) can provide invaluable information to facilitate the identification of metallurgical issues that may arise during processing of a particular ore. This paper will discuss the use of QEMSCAN analysis in conjunction with bench scale flotation test work to determine metallurgical characteristics for several ore types that will be fed to the Morenci concentrator upon commencement.

Jan 1, 2007

By G. Avramovic-Cingara

Grain boundary characteristics and microstructural evolution are analyzed in a comparative study using orientation imaging microscopy (OIM/SEM) and transmission electron microscopy (TEM/SAD). The subgrain sizes and misorientations were determined by the OIM for aluminum deformed in torsion to equivalent strains between 0.2 and 4 over the temperature ranges of300-600°C and strain rates 0.01-1 s". The OIM gives clearer evidence of boundaries with high misorientation than does TEM, but it overestimates their frequency b y missing boundaries less than 1 0. T EM more clearly reveals low-angle arrays of widely spaced dislocations resulting in finer subgrain sizes than those indicated by OIM. The evidence supports a mechanism combining dynamic recovery (DRY), deformation band formation with permanent boundaries and geometric dynamic recrystallization (gDRX) in contrast to the hypothesis known as continuous dynamic recrystallization (cDRX).

Jan 1, 2004

By A. J. DeArdo

Linepipe steels have come a long way in the past forty years. In fact, modern, high strength steels for large diameter linepipe applications represent one of the seminal accomplishments in metallurgy of the past half-century. The synergy of advanced steelmaking, alloy design including microalloying, hot rolling, and interrupted accelerated cooling has led to the marvelous steels being used today. The drive for higher performance pipelines has been motivated by the energy sector of our global economy who wanted both higher throughput capacity, i.e., larger diameters and higher pressures, and lower material cost, i.e., relatively thinner gauge wall thicknesses. These requirements led to new steels with higher strengths, better toughness and improved weldability. The goal of this paper is to trace the evolution of linepipe steels from the X60 grades of the small diameter pipelines of the 1960s to the (X80 - X120) grades used in the large diameter pipelines of today. The metallurgical triumphs permitting this success story, e.g., clean steel practices, controlled rolling, microalloying with Nb, and using IAC to obtain low temperature transformation products, will be highlighted and discussed.

Jan 1, 2005

By Peter Broad

"Extracting any metal, especially specialty metals and rare earth elements, requires an in-depth analysis of the costs and potential revenue as well as a due diligence study of other stakeholder interests. Rare earth projects are generally in the billion dollar US range or above, and thus failure to accurately predict any loss of revenue caused by impurities within the product or additional effluent treatment costs can destroy an otherwise viable study. Two prime sources of input impurity are considered: impurities in the material feed and from reagents. The effect of these impurities factor on both the product (in reduced revenue) and on residual “tailings” that may incur additional unforeseen costs.INTRODUCTION“Truth passes through three stages. First, it is ridiculed. Second, it is violently opposed. Third, it is accepted as being self-evident” – Arthur SchopenhauerThe era of unscoped, unbudgeted construction ended about 150 years ago. Today’s engineer must design with confidence; but do so amidst proprietary secrets and unfamiliar pollutants, which present a myriad of interesting challenges. Is it possible to build a viable rare earth plant to a realistic budget, without destroying that which we cherish? Some see this as contradictory but in reality it is the only viable option.WHEN GOOD PROJECTS FAILWithout rare earths the Copenhagen agreement might be null and void. Running a wind turbine with a 30 tonne conventional magnet requires some hefty engineering and prohibitive investment. Despite their ‘Green metal’ applications, production of rare earths have created environmental nightmares, as Folger stated in 2011 when visiting Baotou, or has Jaing Mainheng who has been quoted by Ambrose Evans-Pritchard 6 Jan 2013. This comment is not a criticism of China; the details are from a 2012 white paper published by the Chinese Government that initiated a $6 billion environmental clean-up. Nor is China unique; other plants have had problems as well. There were toxic leaks in the 1990s from Mountain Pass, and the Mitsubishi Bukit Merah Plant (built in Malaysia in 1958) required a $100 million clean-up."

Jan 1, 2016

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By R. Brough

"Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind - and Secondary Hills. There are, however, only a few Primary Hills in operation with ""solid"" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a Cost per ton basis and/or downtime for liner replacement would be to a high.In other words, solid rubber has limits as any other material. However, 'SKEGA started to think, why not try to use the best properties of rubber as well as steel and combine the two materials together.Nearly 10 years ago SKECA started to test this concept in Rod Mills. A steel cap was vulcanized on to the leading face of the lifter bars, to be installed close to the feed end head (fig. 1)."

Jan 1, 1988

By G. J. Knighton

Introduction The Sullivan concentrator treats the complex lead-zinc-iron ore from the Sullivan mine of the Consolidated Mining and Smelting Company of Canada, Limited, to make a lead and a zinc concentrate for its metallurgical plants at Trail. Three miles separate the mine and mill, which are situated near the town of Kimberley, in the East Kootenay district of British Columbia. The orebody consists typically of banded sulphides, mainly galena, sphalerite, pyrrhotite, and pyrite. Important factors in the concentration of the ore are its exceedingly complex and its high specific gravity. It should be remembered throughout the paper that results and figures are based on Consolidated's experience with the Sullivan ore. The present mill feed rate is 8,500 dry tons of ore per 24 hours, for an operating week of five and a half days. Grinding and classification of the ore are carried out in three stages and, in addition, there is a re-grind section which re-treats the zinc middling. It is the purpose of this paper to discuss the classification in the various stages and to give the results o comparative tests which have been carried out for the purpose of improving operations in the mill. The Primary stage consists of six units, each made up of a ball-mill and classifier (see accompanying flow-sheet). Four units operate in open circuit and two in closed circuit. The secondary stage consists of eight ball-mills operating in closed circuit with twenty-one classifiers. In the Tertiary stage are two ball-mills in closed circuit with eight classifiers. The re-treatment section for re-grinding the zinc middling comprises one ball-mill in closed circuit with two classifiers.

Jan 1, 1947

By Stefan Wallner, Andreas Filzwieser, Stefan Konetschnik, Reinhard Preiss, Iris Filzwieser

"Process Safety Management for METTOP means avoiding risks as far as possible - but also dealing with the residual risk by using all existing management tools or external assistance, if required. The presented paper has two parts. The first one introduces a new and very safe cooling technology for metallurgical furnaces. The second part shows how to deal with the residual risk as well as minimize it by using the tapping area of an electric arc furnace as an example.Today more and more intense furnace operations require effective cooling in order to achieve low refractory wear and good furnace lifetime, making cooling technology an important aspect of furnace operation. However, the use of water - today’s standard cooling medium - has some disadvantages, as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion.To overcome the disadvantages of water, a new cooling technology using an alternative cooling medium, namely ISIS B (a special kind of ionic liquid) was developed. The main advantage of ISIS B is the fact that no explosion occurs when this liquid comes in contact with molten metal. The working temperature range of ISIS B of 50 to 200 °C results in other advantages as there are no corrosion problems and no risks of hydration.The fact that no explosion occurs when ISIS B contacts molten metal leads to a revolutionary solution for the metallurgical industry in terms of safety. Especially in critical areas - like tap-holes - new safety standards can be achieved.Together with the TÜV Austrian Holding AG a risk analysis was done for a water cooled tap-hole as well as for a tap-hole cooled with ionic liquids. It is shown that using the new technology the risk can be decreased dramatically and the importance of a best available technology is described."

Jan 1, 2014

By W. W. Beaton

The Coxheath copper mine is situated on the north side of the Coxheath hills and opposite the French Vale, at a distance of about 10 miles southwest of Sydney, Cape Breton county. The deposit was discovered in 1880, and the first work on the property was carried out with local capital. Lacer some Boston men became interested and formed a Company to finance the undertaking. This group operated the mine intermittently for approximately 20 years, spending close to one million dollars on the undertaking. Three shafts were sunk to depths of 110, 190, and 340 feet, and further underground workings to the extent of approximately one-half mile were driven. Also, an extensive surface programme was carried out. in which many test pits and hundreds of feet of trenches were dug, Early in the summer of 1928 the Arno Mines, Limited, optioned the property and immediately started an exploration campaign. A series of trenches were dug along the parallel vein system, and over 4,000 feet of diamond-drilling was done. The results obtained were so encouraging that a mining plant was erected in the fall of chat year and No. 2 shaft was drained. A complete new plant was installed, consisting of one 120 h.p. Fairbanks-Morse Diesel engine, direct connected to a Sullivan angle compound, air compressor; an 80 h .p. Leonard boiler, which supplies power for the 7 by 11 Ingersoll-Rand hoist; and a Sullivan class C steel sharpener and oil furnace. Two 250-gallon Cameron pumps, one operated by steam and the other by air, were placed in the mine so that, in case of a break-down, the mine would not be flooded.

Jan 1, 1930

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By Derek Apela, Coralee Heske, Bunyamin Kahraman, Muhammad Adi

Effective blast fragmentation is essential in underground mining, as it directly influences downstream processing efficiency and operational expenses. This study investigates the application of Non-Newtonian Fluids (NNF) as stemming materials, presenting a novel method to enhance energy confinement, minimize environmental impact, and optimize blast performance. NNFs exhibit shear-thickening behaviour, enabling them to transition between fluid-like and solid-like states under stress, which renders them suitable for regulating explosive gas ejection during blasting. Field trials were performed by Vale Base Metals in Thompson, Manitoba, in their underground nickel mine to evaluate conventional slag stemming against NNF-based stemming in production-scale blasts. Emulsion explosives were employed, and blast performance was assessed through velocity of detonation (VOD) measurements, vibration monitoring, and AI-assisted fragmentation analysis using WipFrag. Preliminary results indicate that NNF stemming improves fragmentation, resulting in a reduction of D50 by as much as 38%, enhances energy confinement, and may decrease the incidence of hole plugging and re-drilling in subsequent blasts. This study presents an alternative to conventional stemming methods, highlighting potential advantages for enhanced safety, efficiency, and sustainability in blasting operations. Additional research and field trials are necessary to improve implementation protocols and facilitate the widespread adoption of this unique method in the mining sector.

May 4, 2025

By E. Essadiqi, P. Poruks, D. Boyd, D. Emadi, I. Yakubtsov, T. Turi

This paper reviews the results of an extensive study of microstructures and mechanical properties in bainitic linepipe steels. The research was carried out as a collaborative project between Queen's, Stelco and CANMET. Basic studies of phase transformations and mechanical properties in these steels established important relationships between processing schedule and microstructure evolution, and between final microstructure and mechanical properties. The best combination of strength and toughness properties is obtained with a microstructure comprising a matrix of intragranularly-nucleated bainite (`acicular ferrite - AF') and small (~ 0.5 µm) dispersed particles of martensite (`M/A'). We describe this as a dual-phase AF+M/A microstructure. An experimental study on 15-mm thick plate determined the window of steel composition and processing parameters which gives the dual phase AF+M/A microstructure. The minimum strength and toughness properties for Grade 621 (X90) linepipe steel can be achieved by either a lean steel composition (0.04C-1.77Mn-0.04Cr¬0.32Mo-0.31Ni-0.29Cu-0.08Nb) with extreme processing parameters, or by a higher alloy composition (0.04C-2.07Mn-0.50Cr-0.51Mo-0.04Nb) with a more industrially realistic processing schedule. It is proposed how this approach could be extended to obtain higher strength linepipe grades.

Jan 1, 2005

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012