Search Documents

By Carolyn Kenney, Jianjun Liu, Zhenghe Xu

"The flotation of fine particles has been a challenge to scientists and engineers in mineral processing. A novel concept of reactive oily-bubbles as carrier to float fine particles is described in this paper. The reactive oily bubble flotation is considered attractive for fine particle flotation. In addition to the role of fine particle agglomeration by oily films, the surface properties of air bubbles coated with a thin oil film can be better controlled for the desired selectivity by adding certain types and concentrations of water insoluble collectors into the oil phase. This approach can eliminate the addition of collector to the aqueous phase, avoid undesired synergetic interactions among collectors, activators, depressants and dispersants present in slurry, minimize undesired activation of gangue particles and significantly reduce the amount of collectors needed.The concept of using reactive oily-bubble to achieve selective flotation was demonstrated in contact angle measurement and by microflotation tests with fine sulphide minerals: sphalerite and galena in this paper. The flotation behavior of sulfide minerals can be radically modified with adjustment of solution pH, addition of depressant and activator as in conventional flotation. The successful separation between PbS/SiO2, ZnS/SiO2 and PbS/ZnS was demonstrated using mixed mineral systems. Compared with conventional flotation, the reactive oily-bubble flotation showed a stronger collecting power.INTRODUCTIONThe challenge for fine particle flotation has long been recognized and well documented (Fuerstenau, 1980). Because of drastic changes in surface properties of fine particles and associated physicochemical and hydrodynamic conditions of flotation systems, fine particles responded poorly to the conventional flotation processes. For instance, the small mass and hence low inertia of fine particles would result in a low efficiency of collision and attachment of fine particles with flotation bubbles. Large specific surface area of fine particles, on the other hand, would cause an increased reagent consumption. Dominating colloidal forces of fines may cause slime-coating, accompanying a low selectivity (Somasundaran & Arbiter, 1979; Fuerstenau, 1980; Sivamohan, 1990)."

Jan 1, 2003

By L. Li, K. Jiang

China is the world largest producer and consumer of zinc. Beijing General Research Institute of Mining and Metallurgy (BGRIMM) is one of major research and engineering institutes for nonferrous metallurgy in China. This paper (presentation) introduces the development of China’s zinc smelting industry, key production processes and main producers. The process research and development are reviewed as well as BGRIMM’s R&D activities in the last decade. China's refined zinc production was 4,829kt in 2012, accounting for 38.6% of world production. Primary production was 4,722kt. There are around 150 refined zinc producers in China. The traditional fluid bed roasting - leaching jarosite is still a dominant process for primary production and its production accounts for about 60% of country's total production. However, the direct leaching process is gaining market share. Seven direct leaching plants with 330kt/a capacity, including autoclave leaching and the Outotec direct leaching, have been put into production by June 2013. Five autoclave leaching projects with 590kt/a capacity are in the pipe line and are expected to be commissioned in 2014 and 2015. To cut the production cost and improve smelter economics, process research to optimize the production flow sheet, to improve the iron removal and to enhance the recovery of co-existed rare metals were carried out. The development trends of China’s zinc smelting industry from the view of cutting production cost, improving energy efficiency, increasing comprehensive utilization are discussed accordingly.

Jan 1, 2014

By J. H. Shillabeer

"Rational exploration requires the prior selection of areas possessing excellent geological potential and minimum hazards to commercial development . Within an over-all strategy of grass-roots exploration, two procedures for selecting areas for (i) coal and (ii) metals exploration are described. The procedures explicitly balance infrastructure requirements and environmental concerns for areas of geological merit not alienated in parks and reserves. Through consensus, priorities are attached to those areas meriting closer scrutiny and field reconnaissance.IntroductionMining companies need to know that having made a potentially economic discovery, they will be allowed to develop it with minimum delay and at reasonable cost. The environment for exploration in British Columbia is complex and recent experience suggests that conditions are not becoming any easier. Conflicts over land use issues, preservation and economic development are common. The high cost of exploration requires that the risks should be offset where possible by: (i) carefully selecting the areas in which to work (ii) conducting operations in a responsible manner, and (iii) working cooperatively with the community of interests. This paper concerns the first action: prior selection of areas.To aid exploration planning at Suncor, a procedure was developed to grade those areas of the province possessing favourable geology according to the ease with which a mine might be developed . This had to be done within the constraints of the company's over-all approach to exploration. This emphasizes ""grass-roots"" exploration of self-generated projects in British Columbia. In addition, having selected a favourable belt of rocks, it is intended to persevere there while steadily adding to the accumulated data base and local experience. Hence, it is intended to concentrate on an area. This implies a long-term commitment to an area which in turn increases the importance of the original selection.Suncor's search is directed to finding base and precious metals in intrusive and volcanic environments, and export quality coal."

Jan 1, 1985

By Robert P. Harrison, Marie-Christine Patoinel, Kristian E. Waters

This paper describes a collaboration between McGill University and Hatch Ltd. to expose undergraduate students to real-world industrial projects. As part of the final-year design course, the students receive a detailed lecture on Scale-Up of New Technologies', including seven case studies drawn from over fifty years of full-scale industrial projects. The students are taught the basic concepts of scale-up, including the limits of pure theory and the need for empiricism. Insights from real scale-up failures and successes are fictionalized as Projects A, B, C, etc. The students are then asked to identify the guiding principles that can be distilled from these case studies.

Jan 1, 2011

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrates identified gold to be mainly present in the form of a solid solution in pyrite. Gold distribution resulted in a poor extraction yield of 55 % by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction and has led to a gold extraction yield of 94%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and used a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a diaphragm-less electrolysis cell. The extracted gold was recovered via adsorption over silica and the gold depleted brine was treated for impurities removal. This brine was recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Jan 1, 2014

By J. L. Bowlby

OWING to the pressure of routine analyses at the laboratory during the past year, work of an investigational nature on water problems has been greatly curtailed. Favourable reports by the boiler inspectors indicate that the operators are giving satisfactory attention to feed-water treatment at the several . power plants. Some of the operators prefer lime and soda, others the phosphate and soda treatment. Springhill is still on the same commercial treatment as they were using last year, and satisfactory results are being obtained. This individual preference for a particular treatment, although it may be different for feed waters of similar nature, indicates that so long as proper conditions of alkalinity and concentration are maintained within the boiler, it is immaterial what chemicals are used in the treatment. This statement refers, of course, to the low-pressure boilers. In high-pressure boilers, a treatment such as lime and soda cannot be satisfactorily employed, on account of the precipitated calcium carbonate unduly increasing the amount of suspended matter. Only one case of impending trouble was reported during the year. That was at Seaboard, shortly after the new unit was placed in operation. Dissolved oxygen, considerably in excess of the permissible 0.030 cubic centimeters per liter, was detected at various points on the feed line. It was suspected that a de-aerating heater was being operated at too low a temperature, and chemical tests, made before and after the necessary adjustments, proved that this was the source of the trouble. While it has been impossible to give mine waters the attention they require, progress can be reported in the work carried out by the Mechanical Department. Past investigation of the action of mine water on various acid-resisting alloys is now bearing fruit, and it can safely be said that repair work on mine pumps has been reduced by nearly one-half.

Jan 1, 1938

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

By John Kostuik

"This paper discusses the outlook for uranium resources, and comments briefly on the measures needed to meet market objectives. Areas of recent exploration interest are also discussed.THE PREVIOUS SPEAKER has capably described the truly phenomenal growth in demand for energy from all sources. The basic factors -population growth and industrial development -which will create energy demand are so fundamental to national economies that the ascending energy demand curve will be little affected by short-term factors.Because of the economic and practical advantages of nuclear power and the degree of present acceptance by electric utilities, there is no doubt that uranium will be a principal source of primary energy in industrial countries -and this will happen within a decade. Indeed, during this period it will be the fastest growing source of energy, capturing, for example, more than half of the electric utilities' expansion in the United States by 1980. The ready availability of energy sources from domestic and foreign resources is so essential to industrial nations that the long-range outlook for their adequacy is of prime importance. There has been international concern about the availability of uranium resources at reasonable cost to adequately support and foster the development of the nuclear power industry. Canada, fortunate in having established reserves and a potential in excess of any forseeable domestic demand, can confidently look forward to being a principal supplier to the industry."

Jan 1, 1969

By Charles G. Kemsley

IN view of the truly remarkable development of special steels for special purposes, the mining industry has for years looked forward to a time when steel makers would come forward with a product which would be an improvement over the straight carbon steel which has always held the field for drilling rock. In order to avoid making changes in conventional shop practice, the industry has perhaps been too insistent upon obtaining a water hardening steel which could be handled in the blacksmith shop by long established methods. As early as 1932 or 1933, an oil-hardening tool-steel of the one per cent carbon, plus chrome, plus molybdenum type was applied to hollow drill steel. It was known as a hard as well as a tough steel, and one that, theoretically, should give a good account of itself as a rock drill, if properly heat-treated; and so it has proved in actual trials. There were numerous deterrents which retarded adoption of this steel. For several years there has been a constant improvement in the drilling qualities of the straight carbon steel, and, considering the higher unit price ? of the alloy, there has been considerable doubt in the minds of some mining? men as to what advantage there might be in the use of alloy over straight carbon for hollow drill steel. The alloy being an oil-hardening steel, its adoption meant having two kinds of steel in the mine, for a time, and that spelled trouble, unless some positive means of identification was adopted. The hardening and forging ranges of alloy steel being narrow also made necessary much closer control over these operations if poor results were to be avoided. These thoughts undoubtedly prevented its use becoming wide-spread, for, as a matter of actual record, less than fifteen per cent of all the hollow drill steel used in Canada today is alloy.

Jan 1, 1942

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007

By M. S. Badollet, W. C. Streib

"AbstractA commercial method .has been developed for controlling the texture of chrysotile asbestos fibers so that they may possess properties comparable with natural sem1-harsh fibers for use in wet •processes.The physical properties of the soft, silky and slimy fibers are partially altered by a flash-heating process which removes a portion of the molecular water.The heat-treated fibers show an improvement in filterability, an increase in bulk, absorption, and surface area and better electrical properties, such as volume resistivity.IntroductionCHRYSOTILE ASBESTOS fibers are found in nature having varying degrees of texture, referred to as soft, semi-harsh, and harsh. Fibers of each type of texture have inherent characteristics which directly affect their usefulness to industry. Visual differences are apparent under a microscope where it is seen that the soft-textured fibers have a silky, serpentine or wavy appearance, whereas the harsh-textured fibers are coarser and spicular. Semi-harsh fibers, of course, have properties intermediate between these extremes.Fankuchen and Schneider ( l) have shown by the use of low-angle X-ray scattering that the diameter of the harsh type of chrysotile fiber is somewhat greater than tha of the soft variety. Surface area measurements on various chrysotiles of different textures tend to confirm their findings. By nitrogen adsorption methods, it was found that the surface areas of soft types of chrysotile asbestos are approximately 23M2 / g whereas for the harsh types they are as low as 11M2/g."

Jan 1, 1955

By Jeonghwan Kim

Intelligent Excavation System (IES) has been considered to be one of the desirable solutions to improve the productivity, quality and safety of the current earthwork processes. IES is composed of various hardware and software modules including task planner (work command generator), local and global work environment sensors, GPS and other sensors to acquire the excavator?s status, robotic controller and electronic valves, and the manipulator (excavator). A data communication manager was required to coordinate the signal or data-flow in between these modules considering the operational status of IES such as; excavation start/completion, truck detection, terrain model update, emergency stop, local sensing, GPS/motion sensor data handling, and so on. This paper presents the role and functions of this data communication manager. After every possible operational status of IES operation was identified, a protocol of each communication process in the form of string-type was made. The components of IES are connected with either wired or wireless network. Therefore, they can communicate with the manager using socket (TCP/IP) communication. The data communication manager is also capable of accessing a web-based project management information system, which constantly updates the performance of excavation robot to online database.

Aug 1, 2013

By William D. Macdonald

The Upper Devonian Kettle Point black shale of southern Ontario is poorly exposed. Structural maps pre-pared from the data of numerous wells show that the upper surface of the formation has low regular relief, and that the lower surface reflects domes in the Middle Devonian and also local subsidence of the Devonian rocks due to solution of salt in the Silurian Salina Formation. The appearance of minor amounts. of marcasite, pyrite, and calcite, m that order, as interpreted from the evidence of concretions from the type locality at Kettle Point is thought to have been influenced by a rise m the pH within anaerobic sediments preceding compaction.

Jan 1, 1960

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By W. M. Williams

"Although manganese is a metal virtually unknown to the layman, it is hardly necessary to point out to the engineer the importance of manganese in modern metallurgy, an importance intimately linked with iron (and steel), the basic materials of engineering construction for hundreds of years and certain to remain so for long into the future. World steel production will approach and perhaps reach 1 billion tons/year in the 1980s; with a manganese content between 0.5% and 1 % in ordinary steels, and more in specialty steels, manganese use worldwide will soon approach 15 million tons annually. Manganese was discovered and isolated in Sweden in 1774 by Karl Wilhelm Scheele (who also discovered molybdenum), but the element was only of scientific interest for several decades. By the early part of the nineteenth century, however, manganese oxide had become commercially available and was in use for colouring glass and for the production of chlorine. Commercial application in metallurgy appears to have been limited to the manufacture of crucible (or ""cast"") steel, a highquality product made by carburizing wrought iron, and melting it in small batches to make ingots which could be rolled and used for special applications, e.g. for the manufacture of fine tools or for ""steeling"" the cutting edges of implements such as wrought iron axes and chisels.* However, it was not until Bessemer's epoch-making invention of cheap steel in 1856, and the dramatic expansion of the steel industry thereafter, that manganese assumed the importance that it holds in modern steelmaking."

Jan 1, 1999

By J. C. Hampton, L. A. Matzar, C. R. Gamwell

In geomechanics, conducting uniaxial or triaxial compression tests require samples to be prepared to a certain length-to-diameter ratio. This ratio is typically defined as 2:1 (length to diameter) and is accepted as a common standard for all materials on which mechanical properties testing is performed. Variations in sample length can cause changes in measured strength properties across multiple material types, such as cement, rock, or soil. Within the oil and gas industry, it is not uncommon to receive samples for technical services work that are slightly under or exactly the length requirement before surface grinding and sample preparation. Many of these samples are discarded from uniaxial and triaxial compression tests and used in another manner; therefore, it is necessary to study the length-to-diameter ratio in efforts to understand the limits and validity of testing samples that are slightly out of the 2:1 ratio. This paper discusses uniaxial compression tests performed using Berea sandstone and a standard cement mixture of 2.54-cm diameter to study changes in rock strength and properties. Compressive strength for each lengthto- diameter ratio over a range of 0.5:1 to 2.2:1 was measured. The investigation was extended to study near-end effects, where the sample length is near, but not exactly twice the diameter. It was discovered that the cement samples conformed reasonably well to the suggested ASTM correction factors. The sandstone did not conform to the correction factors and further analysis is required to develop a correction factor unique to the material. Near end effects, in both the cement and Berea, were found to increase compressive strengths, especially when the L/D of the samples was increased slightly over a 2:1 L/D.

Jan 1, 2015

By K. Robertson, K. A. Scalise, K. C. Kocsis, M. B. Teixeira

"Many deep and highly mechanized underground metal mines require cooling. In many cases, appropriate working conditions might be fulfilled by ventilation alone, but some require the implementation of cooling systems. The most common cooling systems are bulk air cooling and localized cooling. These systems are effective, but they use considerable amounts of electricity. Ground source heat pumps (GSHP) can supplement existing cooling and heating systems, while geothermal systems can cool the mines in their entirety if there are significant sources of geothermal energy are present. A major advantage of geothermal and GSHP systems are their renewability, which reduces the carbon footprint of the mine.INTRODUCTIONThe western United States has abundant alternative energy sources including a high potential for geothermal energy. Geothermal utilization is a viable energy alternative that many areas throughout the world have access to because high geothermal potentials are located near areas of volcanic activity such as along plate boundaries, mid-oceanic ridges, rift valleys and hot spots (IRENA, 2017). There is significant potential to use geothermal energy for many applications. With constantly evolving and innovative technologies being developed, an increasing number of geothermal applications are becoming feasible. The western United States is an ideal candidate for alternative energy applications due to the geothermal availability and the emergence of modern technology. This paper investigates the incorporation of renewable methods and the alternative energy possibilities of Barrick Goldstrike, located in northern Eureka County, NV and Rio Tinto/BHP Billiton’s Resolution Copper mine located in Superior, AZ.RENEWABLE SYSTEMSGeothermal SystemsGeothermal temperatures are typically defined as either high or low temperature systems(Shengjun, Huaixian, & Tao, 2011). The high-temperature reservoirs (>220°C / 428°F) are feasible forlarge, commercial production of electricity with dry stream and flash stream systems (Shengjun, Huaixian, & Tao, 2011). Low temperature systems, below 220°C (428°F) (Shengjun, Huaixian, & Tao, 2011), aremuch more difficult to use for energy production. Low-temperature reservoir heat can be harnessedthrough the implementation of a binary cycle plant. The working fluid for a binary cycle plant is eitherorganic (Organic Rankine Cycle (ORC)) or an ammonia-water mixture (Kalina cycle). Organic fluids andammonia-water mixtures have low boiling points that allow for the recovery of heat from low-temperaturesources (Eymel Campos Rodriguez, et al., 2013). The efficiency of the binary cycle plant varies depending upon the fluid, thus the proper selection of the fluid is critical for maximum energy output"

Jan 1, 2019

By G. O. Oniyide, H. Yilmaz.

"This paper presents the result of the research done on the effect of temperature on the dilatancy of rocks from the Bushveld Igneous Complex (BIC), where the South African Platinum mines are located. The BIC has higher virgin rock temperature (VRT) than the gold mines of the ‘Witwatersrand Basin Complex’. If the platinum mines advance to ultra-deep levels as the gold mines, since the Merensky Reef has been reported to extend beyond 5km, then the virgin rock temperature at 5 km below surface would be approximately 140oC. Hence, there is a need for the investigation of rock behaviour at high temperatures. Five different rock types (norite, leuconorite, mottled anorthosite, pyroxenite and chromitite) were tested in a 2600 kN servo-controlled multi-purpose triaxial testing machine. The tests were done at a constant strain rate of 5 x 10-1 S-1 and a confining pressure of 10 MPa within temperature range of 20 °C (ambient temperature) to 140 °C. The results show a general strength reduction and increasing dilation angles with increasing temperatures. The results also demonstrate that dilation angle is close to the internal friction angle at lower temperatures; however, they are greater at higher temperatures.INTRODUCTIONMany challenges are faced with increasing depth of mining in underground mines. The most obvious are heat, in-situ stresses and those associated with logistics. Issues related to underground heat have mainly focused on the side effect of heat on workers' health, increasing production costs as a result of higher cost of ventilation. The effect of increasing temperature with increasing depth on the behavior of rock has not been given much consideration. Generally, gold mines in South Africa are deeper than the platinum mines but the latter have higher temperature gradient, which makes the platinum mines to be warmer at similar mining depths. Although the study of the effect temperature on the behaviour of rock can be beneficial to both gold and platinum mines, the focus of the research is limited to the platinum mines because of their higher temperature gradient. Donoghue (2004) stated that the virgin rock temperatures (VRT) and air temperatures increase with depth, due to the geothermal gradient and auto-compression, that is, compression of air by its own weight."

Jan 1, 2015

By A. Zangooi, J. A. Finch

"A frother analysis technique based on the formation of a colored solution with UV-VIS absorbance proportional to frother concentration over a certain range has been developed. The calculation of concentration requires the comparison of the sample absorbance at a selected wavelength with a linear calibration (frother concentration vs. absorbance) constructed with values collected from solutions of known concentration (standards) at the same wavelength. It has been found that concentration ranges for preparation of standards can vary widely. An integration of our experiences into a databank can offer some guidance on the selection of standard concentrations. The databank includes results from the analysis of 37 chemical reagents, commercial frothers, and natural oils used in research work or at industrial sites. Grouping frothers by similar chemical structure or origin provides a good basis for selecting the standards to approach the maximum absorbance range for the spectrophotometer in use.INTRODUCTIONA technique to determine frother concentration on samples of industrial milling streams based on formation of a colored solution with UV-VIS absorbance proportional to frother concentration has been developed. The concentration is determined by comparison of its absorbance, at some selected wavelength, with those obtained by processing a series of solutions of known concentration (standards), at the same wavelength. It is desirable to have linear calibration (frother concentration vs. absorbance) over the widest concentration range. The upper concentration can be restricted by the instrument, as there is a maximum detectable absorbance (minimum transmittance), which can be reliably sensed by the UV-VIS detector (in most cases maximum absorbance is 3)."

Jan 1, 2016