Search Documents

By Michael Drozd

"The operation of an activated charcoal system has five separate unit operations. These unit operations have common points for CIP, CIL and CIS system, which vary widely in application.The unit operations are:a. Absorptionb. Desorption (Stripping)c. Acid Washingd. Reactivatione. Carbon Handling (carbon transportation, sizing, dewatering, etc.)Cost optimization starts with the basic operating parameters (design philosophy) set down at the time of engineering design. These parameters undergo almost immediate change due to site specific ore requirements, throughput changes, operator requirements or reagent availability.Activated charcoal is sometimes viewed as simple, uncomplicated reagent that requires not optimization. To some extent, this statement is true, but under most circumstances, if the time necessary to optimize the use of activated charcoal is available, the effort is rewarded with significant savings. CPL-Carbon Link has embarked upon a program of supplying technical support with its activated charcoal. Several operations in the United States have undertaken to have CPL-Carbon Link do an operational survey to determine if potential savings are possible. CPL-Carbon Link has offered to do these surveys for projects that are clients or simply would like to have CPL-Carbon Link review their operation. The information accumulated by CPLCarbon Link is being used to attempt to fashion industry standards so that a common reference point can be established for activated charcoal usage."

Jan 1, 2008

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By J. G. Henning, T. R. Yu, J. E. Croxall

"Test work was carried out to investigate the thermal response of loose and solid rock under varying environmental conditions. The primary interest was to develop a technique that could be used to increase the thermal variation between loose and solid rock for better detectability of loose rock underground with a thermal imaging infrared scanner.A variety of thermal enhancement methods were evaluated both in the laboratory and in the mine environment. Air temperature variation created by the exhaust from diesel driven, mobile mining machinery was studied in detail. When sufficient hot exhaust was supplied to the air, unsteady thermal conditions became more pronounced on the rock surf ace. This allowed a greater percentage of loose rock to be detected by a high-resolution infrared scanner within minutes.The degree of thermal enhancement of loose rock was found to be dependent directly on the thermal conductivity of rock, looseness, air temperature change, and inversely on the size of loose, airflow rate and distance downwind from the heat source. It was also found that an air temperature rise of at least r c, or rock temperature differential of1°C was necessary for minimal thermal enhancement required f or infrared detection."

Jan 1, 1990

By R. E. Stewart

"Using the concept of economic life and marginal analysis, it can be shown that proper equipment replacement timing can save a mining company many thousands of dollars. To assist management with determining the economic life of mining equipment, a new computer package has been developed. The package, called ERG (equipment replacement guide), incorporates all important economic factors related to equipment usage, such as operating costs, maintenance costs, salvage values, depreciation, volume of work, tax credits, inflation rates, ROJ, etc. The information is used in a series of equations which balance the costs of new equipment against the total cost of old equipment. The solution of the equations determines economic life and the point in time when the old equipment should be replaced. IntroductionIn an operating mine, equipment must eventually be replaced or downgraded for a variety of reasons. Fleets of haul trucks, dozers and other major pieces of equipment deteriorate over time until the mounting costs of maintenance and repair force either a major overhaul or the ir replacement by new and more efficient pieces of equipment.The question of determining the best time to replace old equipment has been approached in many different ways. Various methods, ranging from operating experience, intuition and physical necessity to sophisticated computer models have been devised to help cope with equipment replacement decisions . The best of the se will incorporate the most important economic factors related to equipment usage, such as operating and maintenance costs, salvage values, depreciation, work delivered, the cost of capital, tax credits and, of course, the effects of inflation.Economic TheoryThe fundamentals of equipment replacement theory grew out of the interaction between economics, engineering and finance. The use of annual cost comparisons and rate-of return calculations were helpful in handling situations in which assets with different finite lives were being compared. Later developments bringing together the concept of economic life and marginal analysis helped provide additional refinements to the theory. Taylorui showed that the displacement of an aging asset with a similar, but newer, asset can be justified economically when the marginal cost of keeping the asset one more year exceeds the minimum uniform annual cost equivalent of the proposed replacement."

Jan 1, 1980

By M. E. Holuszko

A research program has been carried out at the Mining Department of the University of British Columbia to study the effect of wettability of coal on its handleability and bulk density. The effect of moisture content on the bulk density of coal was found to be more pronounced for hydrophilic coals than for hydrophopbic ones. Altering wettability of coal surface leads to different effects of moisture on bulk density. The samples were studied at different fine fractions content, and it was shown that there was no effect of increased content of fines on the bulk density for hydrophobic coals, while for hydrophilic coals this effect was very significant. It was shown that the moisture content at which the lowest bulk density was reached coincides with the critical moisture content for studied samples, as determined from handleability tests using Durham Cone method. This critical moisture is the moisture content at which a sudden deterioration of coal handleability occurs. Based on the bulk density and handleability tests, the flow theory of moist coal is proposed.

Jan 1, 2006

By T. M. Korzekwa, R. L. Cavanagh

Following considerable experience with the beneficiation of Wabana iron ore by standard methods, a study was made of the benefits to be obtained by semi-reduction. The basis of the laboratory program was an extensive mineralogical and liberation investigation which guided subsequent work. Partial reduction and beneficiation on a laboratory scale was carried out on lump ore and fines. The reduced ore was magnetically concentrated and the concentrated fines were briquetted. Data are presented on reducibility, sizing vs reduction rate, magnetic cobbing and separation, and the elimination of phosphorus. Past work is reviewed briefly and comments are made on the relation of laboratory to pilot-scale tests.

Jan 1, 1967

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

By S. Steinlechner, G. Schneeberger, J. Antrekowitsch

The recycling of steel mill dusts is getting more and more important. The costs and requirements of land filling are rising and companies are interested in new recycling strategies. The rising of sustaina¬bility hand in hand with the high rate of valuable metals in these residues supports new research activities on the recycling sector. Especially zinc but also iron and lead are economical factors due to the treatment of steel mill dusts. This paper gives a small overview of fundamental studies concerning the chemical and physical composition of these dusts. Furthermore aggregates for the reduction of these dusts in the liquid phase are introduced and compared. The Flash-Reactor, the TBRC-Technology (Top Blown Rotary Converter) and submerged arc furnaces and there use for melting and treatment of these dusts are in the center of interest of this paper. The final conclusion gives an overview of possibilities for reduction of filter dusts in the liquid phase.

Jan 1, 2011

By Andrew J. Freyman, George S. Barry

"Mineral endowment in northern British Columbia and the Yukon Territory was assessed on the basis of geological opinion which was gathered in a quantitative framework of subjective probabilities. The survey area encompassed 364,000 square miles and was divided into 310 cells having dimensions of one degree of longitude by one-half degree of latitude. The response solicited related to tonnage, grade and number of deposits of a particular mineral in each cell. The questionnaire sought an expression of mineral endowment down to mine-able depth as distinct from economic expectations. Details on the questionnaire and responses are presented in a series of contour maps on individual commooities, which illustrate the collective occurrence picture of the respondents. The approach is largely dependent on the cooperation of an adequate number of geologists familiar with the region being examined. This approach to an assessment of the mineral endowment of a region has a wide range of applicability, from the focusing of exploration effort to aiding government and development bodies in the formulation of regional strategies and the planning, for example, of road, rail and power facilities."

Jan 1, 1970

By Unknown

Diesel locomotives for underground haulage have been used in coal mines in Continental Europe for twenty-five years or more. In Great Britain, it was not until 1935 that permission was granted to use them in gassy coal mines, but since that time they have been employed in increasing numbers both in gassy and non-gassy coal mines and in metal mines. Their use underground in coal mines in the United States is still prohibited and the same was the case in Canada until 1946, when permission was granted to operate a Diesel underground in the Adanac mine of West Canadian Collieries, Limited, at Bellevue, Alberta. The locomotive used here is a 50 h.p. Hunslet Mark II. More recently, a 100 h.p. Diesel was placed in operation for underground haulage at No. 18 Colliery of the Dominion Steel and Coal Corporation, in the Sydney coalfield, N. S. Thus, on this continent, Canada has been a pioneer in the use of these locomotives underground in coal mines and there is no doubt that more and more of them will be employed as time goes on. We feel, therefore, that the following notes concerning their design and performance, which we have received from the High Commissioner for the United Kingdom, will be of interest to our members.

Jan 1, 1949

By F. H. Hueston, R. S. Barclay

"Depending on the application, zirconia, fused magnesia and graphite have been found to be the most suitable crucible materials for melting uranium metal and its alloys. Although graphite has been found to be satisfactory for uranium and uranium alloy castings with cross sections of 4 square inches or greater, ceramic-type molds are superior for small sections and those shaped castings which prohibit the economic use of machined graphite molds. Heating cycles, addition mechanisms and furnace conditions for melting are discussed."

Jan 1, 1967

By J. Mullins

Coal was first banked by the Dominion Coal Company, Limited, in 1898, near No. 2 Colliery, the same site as is presently used for that purpose. Though today there are banks at Glace Bay, Sydney, and Sydney Mines, these notes, except when otherwise desirable, will be confined to describing the practice as developed at the No. 2 Banking Station, Glace Bay, as being typical of methods obtaining at all sites. Storing The manner in which the coal was piled is illustrated diagrammatically in the accompanying sketch. A train of coal was brought on the main trestle, which extended the full length of the banking ground at a height of 22 to 39 feet above the natural surface, and dumped into bins which were integral with the trestle work. Chutes from these bins permitted the coal to be fed into 3-ton cars, which were horse drawn laterally on narrow gauge tracks laid about 10 ft. centres, to a maximum distance of 400ft. from the trestle. These cars were end-dump and as the pile extended laterally the narrow gauge tracks were lengthened by shorter or longer filling pieces, so that their ends were always kept at the brow of the bank. Much coal, however, had to be dumped directly on the tracks and hand trimmed to fill the valleys, and level off, between the tracks.

Jan 1, 1931

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By M. Noaparast, N. Nickoletopoulos, André R. Laplante

"This paper presents an application of the use of synthetic ores to study gold recovery by gravity. Three case studies are presented: the first focuses on the use of tungsten to study applications of Knelson Concentrators for upgrading gravity concentrates; the second on tungsten again, in this case to study the performance of a 86 Falcon Concentrator; and the third on lead to mimic gold's grinding behaviour.It is shown that the use of synthetic ores with metallic substitute for gold is not only expedient, but it can also lead to an increased understanding of separation and grinding mechanisms, because of the more accurate results and controlled particle shapes. The case studies highlight the problems associated with gold particle flakiness and gangue density. The grinding behaviour of malleable materials is shown to be complex, as particles can migrate to coarser size classes by flattening and cold welding, and to finer size classes by folding and actual breakage.IntroductionThe title of this contribution is not entirely misleading. Mineral processing has much to do with philosophy, rather Philosophy, as described by Georgius Agricola:""Furthermore, there are many arts and sciences of which the miner should not be ignorant. First there is Philosophy, that he may discern the origin, cause, and nature of subterranean things; for then he will be able to dig out the veins easily and advantageously, and to obtain more abundant results from his mining. ""1"

Jan 1, 1995

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By F. J. Alcock

IN the summer of 1934, gold was discovered on Lodge bay, on the north shore of lake Athabaska in northern Saskatchewan, about fifty miles east of the Alberta boundary line. The first claims were taken up by the Consolidated Mining and Smelting Company of Canada, Limited, and there was a &apos;rush&apos; to locate similar showings. Staking continued through the summer and succeeding winter, and in the spring of 1935 the provincial government established a recording office at a convenient point which is central to the more important holdings and where &apos;planes can land in any weather. During the past summer, the name of this townsite was changed from Beaverlodge to Goldfields, and a post office was established here. The season was one of great activity; a great deal of assessment and development work was carried out and a large amount of further prospecting done. In addition to the work by private companies, geological investigation was carried out in the region by a Federal Geological Survey party under the charge of the writer and a reconnaissance examination was made of an area of some 7,000 square miles surrounding the region of particular interest. Though this was the first discovery of gold in the region it was not the first occasion that prospecting had been carried out along the north side of lake Athabaska. Over twenty years ago, a number of prospectors were at work in the area and a large number of claims were staked, many of which were never recorded. One man by the name of Piché, in the years 1910, 1912, and 1913, took up a considerable number of claims north of Pine Channel narrows, east of Fond du Lac. His discoveries, which consisted of small showings of sulphides in sedimentary gneiss, proved to be of no economic importance. In 1915, a sudden widespread interest was aroused by the report that a sample of ore collected near Fond du Lac had yielded a very high assay in silver. In March and April of that year, prospectors began to rush into the field by dog teams to take up claims, and, as soon as the Athabaska river was free of ice, others started by boat from Athabaska Landing. Some hundreds of claims were staked and recorded in the Dominion Land Office at Edmonton or at Fort Smith. By July, most of the prospectors had? left the region, having failed to find any silver ore. In 1921, considerable prominence was given to the area a few miles east of Goldfields by reports that very large masses of iron ore were available there. Claims were taken up, but the material is much too low grade to be considered commercial ore.

Jan 1, 1936

By Tapiwanashe Chenje, David Hewitt, Peter Radziszewski

"Steel media wear is a major cost component in mineral processing. In the case of existing operating mill, steel media wear prediction can be used to help compare the performance of steel media from different suppliers before completing marked ball tests. It can also be used to investigate how ores from different site of a given mine affect steel media wear. In the case of Greenfield cases, steel media wear prediction can be used to estimate the cost of steel media for a given feasibility study.This paper presents a wear testing and prediction methodology that ties together abrasion wear and corrosion wear testing results through the use of a simplified discrete element charge motion model. The experimentation dimension to this methodology takes samples for steel media, mine site ore and water to determine abrasive and corrosive wear parameters of a given media, ore, water set.The test methodology development is illustrated along with a comparison of wear predictions with observed wear rates in some operating mills. A case study is included that illustrates how this methodology was used to estimate steel media wear performance. The paper closes with a discussion on the use of parts of the experimental methodology to investigate other abrasive wear conditions such as liner wear, paste backfill piping and ore breakage as well as avenues for future test development.INTRODUCTIONThe cost of comminution processes represents a significant part of the overall costs of a mining operation. Grinding media/liner wear alone accounts for 15-25% of the total operating cost. The annual steel grinding media consumption is approximately 2.5 mtpa or 0.3% of total world steel production [Smorgon Steel Group, 2005]. Using an estimated grinding media cost of about US$0.75/kg [Halbe and Smolik, 2002], gives a media cost of over US$1.875 billion per annum. Mining continues to shift towards exploitation of lower grade ores as the higher grades get depleted. These low-grade ores require finer grinding for the liberation of the value minerals, and hence it can be assumed that grinding media consumption will also continue to rise.The Bond abrasion test, dating back to 1963, [Weiss, 1985] is still used to estimate the total mill media wear. This is a purely empirical test based on the ore. From Bond abrasion index tests, it is possible to determine a wear rate using the following function:"

Jan 1, 2009

By J. L. Jambor, J. E. Dutrizac, J. B. O'Reilly

The present-day metallurgical community is quite familiar with the use of jarosites [MFe3(S04)2(0H)6 where M = K, Na, NH4, Ag, 1/2Pb, etc.] as a means of controlling iron, alkalis and sulphate in hydrometallurgical circuits. This modern precipitation technology has found an increasingly widespread application in the zinc industry111 and is gradually also being extended into the hydrometallurgical processing of copper and cobalt121 . The chief advantage of jarosite precipitation is that the iron precipitate settles and filters well, and gives low losses of divalent metals in the washed residue. Although this jarosite precipitation technology was developed only within the past twenty years, man&apos;s involvement with jarosites extends back to antiquity, and jarosites have played an important role as a source of silver in several ancient metallurgical centres. In the early days of this century, argentojarosite was an important local source of silver at the Tintic Standard mine, Dividend, Utah, where over 200 000 oz of silver were recovered from highgrade natural jarosite over a three-month period 131 . At the Matagente mine in Peru, pockets of argentiferous plumbojarosite up to 40 m thick were mined and processed by the Indians prior to the arrival of the Spaniards14-51 . In Cyprus there are vast jarosite deposits associated with the ancient mining sitesl51 , but exploitation of these jarosites has been insignificant because of their low silver values. The most extensive mining of silver-bearing jarosite, and certainly the oldest documented instance of such jarosite exploitation, was in the vast pre-Roman workings at Rio Tinto, Spain. This mine, the greatest single miningmetallurgical site currently known from the ancient world and also the oldest site of more or less continuous metal production, has witnessed many metallurgical firsts. Aside from the initial processing of jarositic ores for their silver values, the development of large-scale hydrometallurgy also seems to have occurred at Rio Tinto. As early as 1737, copper was recovered by cementation on scrap iron from the mine waters at Rio Tintol51 . Large-scale heap leaching of calcined ore commenced with the British operations in 1876 and, by 1900, raw pyrite was heap leached to recover associated copper values161 .

Jan 1, 1999

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971