Search Documents

By Edward Sampson

Bases of National Power At a time when the economy of the world is in a particularly troubled state it is appropriate to examine some problems of the distribution of natural resources. I should like particularly to call attention to the remarkable increasing demand for natural resources, to give an analysis of the demand for certain mineral resources, and to direct attention to some problems in satisfying this demand. All industrial power is based on natural resources and the most basic of these are soils, energy resources, and mineral resources. There is a strong interrelation of these resources, more than is obvious, and I shall take up certain aspects from the point of view of a geologist. Few nations are well endowed with all three of the kinds of natural resources I have mentioned and much has been done by some small countries whose peoples are industrious and enterprising and where conditions for free world trade have been favourable. However, major industrial power is dependent on a substantial endowment of all three classes.

Jan 1, 1949

By Yann Sivry, S. Subramanian, Divyasree C. Prabhakaran, Jean Riotte

The potential of a bacterial strain isolated from water samples collected from a chromite mine in Odisha, India has been assessed for the bioremediation of hexavalent chromium, a toxic environmental pollutant. The isolate was identified as Sphingopyxis sp., a Gram negative bacterium, adopting molecular biological protocols and biochemical characterization techniques. Detailed investigations on the bioremoval of Cr(VI) were carried out using Sphingopyxis sp. cells and the various parameters affecting the biosorption process were evaluated. About 55 % biosorption of Cr(VI) was obtained using Sphingopyxis sp. bacterial cells and the residual chromium in solution was found to be bio-reduced to the trivalent form, namely Cr(III). Thus, complete bioremediation of Cr(VI) could be achieved using the mine isolate, with contributions from both biosorption and bioreduction mechanisms. The Cr(VI) biosorption isotherm obtained for the isolate was found to follow a typical Langmuirian behavior and the free energy value of biosorption was determined to be ~-25 kJ/mol, indicative of involvement of chemical binding forces in the bioremediation process. The chromium biosorption kinetics by the isolate followed a pseudo second order reaction. The FTIR spectral studies revealed that carboxyl, hydroxyl, amino and phosphate groups were involved in the biosorption process. X-ray photoelectron spectroscopic studies on the bacterial cells interacted with Cr(VI) confirmed the presence of both Cr(VI) and Cr(III) on the cell surface. The electrokinetic studies revealed that the surface potential of the bacterial cells were less electronegative subsequent to interaction with Cr(VI), compared to the cells alone, which further testified to the binding of positively charged Cr(III) ions, formed by bioreduction of Cr(VI), to the bacterial cell surface. A marginal shift in the iso-electric point obtained for the bacterial cells interacted with Cr(VI), corroborated the involvement of chemical binding forces in the bioremediation process.

Jan 1, 2016

By Colin E. Dunn

The high mobility of gold within the plant kingdom results in detectable accumulations of gold in many plants. Concentrations vary within individuals, among species, and with seasons. From an evaluation of the chemistry of easily acce sible organs of common pecies in the northern forests, it is concluded that alder twigs (or leaves) and conifer bark scales are the vegetation components of greatest use in the earch for concealed gold mineralization. Maximum anomaly enhancement is obtained from twigs collected in the spring. Examples are given of urvey conducted in the La Ronge Domain using 1) jack pine bark (A nglo-Rouyn and Upise Lake areas) ; 2) alder twig (McLennan Lake) ; 3) black spruce bark (Rod Zone near Mallard Lake, and at Waddy Lake) ; and 4) multi-media (Tower Lake). At the latter two sites gold-bearing till is blanketed with late glacial material. Gold enrichment in the plants suggest that the roots are ab orbing gold from the underlying till. Complex processe control the uptake and retention of gold in plants. An understanding of these processes pem1its biogeochemistry to assist in locating near- urface mineralization .

Jan 1, 1986

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By Alexander Burns, David Dreisinger

The kinetics of the oxidation of uranium(IV) by oxygen gas in aqueous systems is dependent on acid concentration, oxygen partial pressure, and temperature. In order to better understand the relationship between these variables and the speed of oxidation, a series of experiments have been conducted where each parameter has been varied in turn. Data were collected continuously using UVVis spectroscopy, allowing for a detailed examination of the reaction rate over the course of each experiment. The data fit an overall apparent rate law that is 1.5order in uranium(IV), -2order in H+, first order in oxygen, and unaffected by uranium(VI). This relationship does not appear to hold for solutions with <0.2 mol/L initial acid, where a different kinetic mechanism appears to be dominant.

Jan 1, 2014

By André Desbiens, Jocelyn Bouchard, René del Villar

"The metallurgical performance of the column flotation process is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a model-based automatic control strategy using froth depth and bias measurements obtained from virtual sensors developed at Laval University. Preliminary pilot plant results on two-phase (water– air) and three-phase system (water – minerals – air) will be presented and eventual industrial implementation of such a strategy as well as the possibility of achieving effective real-time optimization from bias and froth depth measurements will also be discussed.INTRODUCTIONFlotation columns have been widely studied and used in mineral processing for about twenty years. Although a great deal of work has been accomplished to understand the influence of different variables such as froth depth (H), bubble surface area flux (Sb) and bias (Jb) on the metallurgical performance, the measurement of some of these variables is still difficult to be performed – except at the laboratory level – because in most cases, no commercial device yet exists.As a result of this, it is almost impossible to achieve neither efficient control nor optimization of the process at the industrial level, even in open-loop operation. This paper aims at presenting a simple control strategy of froth depth and bias. Description of the sensors used to achieved measurements, preliminary pilot plant results for froth depth control, eventual industrial applications and possibilities for process optimization are also treated."

Jan 1, 2003

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By J. F. McMahon

Introduction The greater portion of the information presented in this paper was obtained in the course of an investigation on clay gathering and its cost in the provinces of Quebec and Ontario (1). For assistance in the preparation of the paper, the writer wishes to record his thanks to Mr. Howells Fréchette, Chief of the Ceramics and Road Materials Division of the Mines Branch. Clays are mineral substances consisting essentially of hydrous aluminium silicate which become plastic when wet, fairly hard when dry, and stony masses when burned to a sufficiently high temperature and re-cooled. Shales are clays which have been indurated by the processes of nature. Millions of tons of clays and shales are won yearly for the production of brick, tile, sewer pipe, drain tile, roofing tile, fire-brick, china-ware, wall and floor tile, cement, and a host of other products. There are certain types of clay which, due to their particular qualities and limited distribution, are mined entirely or in part for sale to manufacturers, and are even exported from one country to another, as for example china-clays or kaolins, utilized in the manufacture of white-wares and in the paper industry, due to their consistent whiteness; ball-clays, utilized in the white-ware industry, due to their bonding power and whiteness; slip-clays, used in the stone-ware industry because of their glazing properties, and in the grinding-wheel industry for their burned bonding properties; and suspension-clays, such as are used in the enamelling industry. However, the great bulk of clays and shales won are used in the production of heavy clay products, and the manufacturer of these generally owns and operates his own deposit of raw material.

Jan 1, 1933

By T. Patching

"MINING operations at the Star Key Mine provided an example of a small-scale prairie-type coal mine that employed several interesting procedures and achieved good productivity with low capital expenditures. The mine was located about 11 miles north of the city of Edmonton, on the north side of the Sturgeon River valley. It opened in 1945 and operated until 1979. Output in the winters reached about 500 tons a day in the late 1940s, but in the spring and summer periods activity was usually limited to only servicing and development work. In the later years of the mine's life sales fell to less than 100 tons per day. Most of its output was bought for domestic use in furnaces and stoves so production of large sizes was desired. A modest market for stoker coal did exist for a time. Screenings (-5 / 8 in.) were sold to the city's power plant until it converted to natural gas and were also used for thawing frozen ground for work on pipelines. These markets were comparatively small and the small sizes did not command as high a price as did the larger sizes. However the extension of natural gas services to rural markets cut into the domestic heating market and finally led to closure of the mine. The coal was strong when freshly mined, but because of its high inherent moisture content, about 25%, it did not store well on surface but tended to disintegrate. It was of subbituminous Crank with a heating value of about 8000 Btu per pound and burned with a clean flame. The seam mined was in the Edmonton Formation, of Upper Cretaceous age, at a depth of 60 to 80 ft below the surface. The seam in the mine area was about 11 feet in thickness but thinned gradually to the north and south and split to the west (1). It was approximately horizontal but gentle rolls in the floor of several feet in height necessitated brushing in places to produce suitable haulage grades. The floor material was of bone and clay, overlying a thin layer of coal. Above the seam there were only a few feet of mudstones and weak sandy shales while the remainder of the overburden was clay and unconsolidated glacial till and surface soil. Because of the soft floor and weak roof material the miners usually left about a foot of coal in the floor to provide a firm working surface and about a foot of coal above the rooms and two feet of coal above the entries to provide a competent roof."

Jan 1, 1985

By S. A. Jacob

Magnesium sheet is notoriously difficult to form at low temperatures without initiating failure, In the present work cold rolling and annealing conditions are varied to produce samples of AZ3lB sheet with a range of grain sizes. The formability of these samples is investigated using tensile testing and forming limit diagrams (FLD&apos;s), The results are discussed in terms of twin types and frequencies.

Jan 1, 2005

By S. Nikolic

"Calcium ferrite slags are currently used in a number of copper-converting processes. Despite the industrial importance of this system the phase equilibria have not been fully investigated. Characterization of this slag system is necessary to improve the control of process parameters, including fluxing and operating temperatures. Recently, a modified experimental method has been developed; this involves rapid quenching of slag samples equilibrated at high temperatures with the resulting phase assemblages analysed using electron probe microanalysis (EPMA). In the present study, experiments were completed under controlled temperatures and oxygen partial pressures using CO/C02 or H2/C02 gas mixtures. The investigated slags were supported during equilibration by a substrate of the primary phase. This technique removes the limitations arising from the use of crucibles and facilitates rapid quenching of the melt. Experiments were carried out at 1200°C and 1250°C (1473 Kand 1523 K) and in the composition range 0-40 wt.% Cu20, 0-25 wt. % CaO and 45-80 wt. % Fe203. Liquidus and solidus data are reported for the primary phase field of spinel between the oxygen partial pressures of 10-4.5 to 1 o- 6-5 atm. The analyzed compositions of liquids and solids are used to construct the phase diagram of ""Cu20"" -CaO-""F ez03"" system in equilibrium with metallic copper at fixed oxygen partial pressures."

Jan 1, 2007

By K. Niboucha, M. Zergoug, S. Brick-Chaouch, H. Houali

"Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items:•,Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists;•,Range of protection (potential of protection along the pipeline);•,Influence of the isolation resistance of the coating on the range of protection;•,Effect of the aging of the coating and its influence on the current of protection."

Jan 1, 2005

By H. Houali

Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items: ? Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists; ? Range of protection (potential of protection along the pipeline); ? Influence of the isolation resistance of the coating on the range of protection; Effect of the aging of the coating and its influence on the current of protection

Jan 1, 2005

By X. Cao, J. J. Jonas, Wanjara. P., J. Gholipour, E. Dalgaard

The linear friction welding (LFW) behaviour of near-ß titanium alloy Ti-5Al-5V-5Mo-3Cr (Ti- 5553) was investigated. Microhardness measurements were performed in order to evaluate the mechanical properties of the welded material. The linear friction welded (LFWed) Ti-5553 was examined with optical microscopy and scanning electron microscopy (SEM) to evaluate the microstructure’s response to the thermomechanical conditions. Characterization of the welds included analysis of the microstructural features of the weld region and thermomechanically affected zone (TMAZ) in relation to the parent material.

Jan 1, 2010

By J. D. Bateman

DURING the summer of 1942 several chromite deposits were discovered in the Lac du Bonnet district about eighty miles northeast of Winnipeg. The deposits are confined to the Bird River complex, a folded composite sill of basic and ultrabasic igneous rocks of early Precambrian age that lies to the north of Bird river (1). The outcrop of the sill represents the trace of an easterly plunging anticline, the south limb extending from the northeast bay of Lac du Bonnet eastward to Bird lake, and the other limb, 6 to 12 miles north, lying between Maskwa river and Euclid lake. The south limb of the sill is 20 miles long, and the northern counterpart 15 miles; but its continuity is interrupted by faulting and by the intrusion of younger granite, so that the total length of outcrop of both limbs does not likely exceed 25 miles. The sill is intrusive into early Precambrian greenstones and associated sedimentary rocks. The chromite discoveries have been made at several localities on both limbs of the sill, and in each case at the same geological horizon. The sill comprises an upper layer of hornblende gabbro and a lower layer of serpentinized peridotite, and altogether is from 500 to 3,500 feet thick. The chromite zone is within and near the top of the peridotite layer, and thus about midway of the sill, both of the limbs of which stand nearly vertical. This geological relationship was established early in the exploration of the initial discoveries and served as the basis for successful predictions of later discoveries. The chromite zone probably persists throughout the length of the sill, but its width and chromite content are not everywhere the same. The initial exploration along both limbs of the sill has shown a combined total length of about 12,000 feet of chromite ore varying in width from 6 to 12 feet. In many places the overburden is thick and obscures the continuity of the chromite zone; but as investigation proceeds the known deposits will be extended and new ones will be found. Thus, although a total length of 12,000 feet of ore has been investigated up to the present time, there is an indicated length of approximately 31,000 feet along which the ore is more than 4 to 5 feet wide. This estimate is based on geological considerations and represents a total tonnage in the order of 15,000 tons per vertical foot of depth.

Jan 1, 1943

By C. Acuña

The case is presented that the key role of frother is control of bubble size in the pulp zone. Compared to water alone, the addition of frother produces a narrower distribution and finer bubble size. An empirical model is presented for bubble size as a function of frother type using a normalized concentration. The model provides a benchmark for assessing operations. There is no agreed upon mechanism of how frothers act to reduce bubble size. Prevention of coalescence is a common explanation and this action is illustrated. The case against the &apos;coalescence&apos; model alone is presented and a breakup mechanism is introduced based on pilot cell and single bubble studies. Phenomena associated with bubble shape, velocity and surface flows are used to illustrate the force associated with surface tension gradients. Breakup mechanisms resulting from this force are proposed. The concept can be extended to high salt concentrations which also promote small bubbles.

Jan 1, 2007

By C. Riveros, H. Henein

Bulk Metallic Glasses have a high potential as advanced engineering materials due to their various properties including strength and corrosion resistance, to name a few. This paper investigates amorphous phase formation and rapid solidification characteristics of impulse atomized Co-based alloys in order to understand and control the application properties of the final products. Amorphous fraction and kinetic crystallization properties of the atomized Co-based alloy powders were quantified by means of Differential Scanning Calorimetry. In addition, different but complementary characterization tools were used to analyze microstructures of the powders. These include optical microscopy, X-ray diffraction and micro-hardness tests. While the amorphous fraction within the powders is promoted by high cooling rate and smaller powder size as expected, hardness is found to decrease with the fraction of amorphous phase.

Jan 1, 2015

By E. J. Wade

The general location, climatic conditions and access of the Tasu mine are covered briefly, with comments on the Jack of conventional transportation and communication facilities. The Haïda story of Tasu and early at-tempts at production are presented, together with a discussion of the government legislation which throttled exploration and production in the late fifties. General and specific details of local geology, mineralogy and current ore reserves are also covered.

Jan 1, 1968

By S. G. Luckey, N. R. Harrison, F. Nadeau, U. Brüx

"The adoption of tailored-rolled or tailor-welded blanks (i.e. TRB/TWB) in the automotive industry has been known to offer great potential for the optimization of weight, function, cost and complexity. Vehicle light weighting can further be achieved by using high strength aluminum alloys like the 7xxx-series. 7xxx-series alloys are capable of delivering specific strengths equal to or greater than high strength steels. However, room temperature formability of this aluminum class is limited, so one approach to forming 7xxx-series alloys is by hot stamping. Hot stamping utilizes an elevated temperature blank and the high pressure stamping contact of the forming die to simultaneously quench and form the sheet. This paper explores the initial feasibility of tailored thickness material for body-in-white applications when processed under hot stamping conditions.INTRODUCTION Steel tailor-rolled blanks (TRB) or tailor-welded blanks (TWB) have been used within the automotive industry as a method of reducing weight, expanding material utilization, and decreasing overall part/assembly cost (Ganeasan et al., 2015; Merklein et al., 2014; Hirt et al., 2005; Kridli et al., 2000). The production of such tailored thickness materials has resulted in over $2.5 billion (2016) in combined industry sales (Mubea, 2018). As automakers begin to adopt the manufacturing practices traditionally reserved for steel such as tailor rolling/welding with greater enthusiasm for vehicle light weighting, there exist an opportunity to expand the material database to extend beyond the traditional aluminum alloys found in current production. High strength aluminum alloys, i.e. 7xxx-series, are ideal for structural automotive applications due to their high specific strength; however, they have limited room temperature formability. Hot stamping, another manufacturing practice used by the steel industry, can be used to form these high strength materials. The combination of tailoring the thickness of a sheet material and hot stamping provides an opportunity for significant weight saving within an existing manufacturing footprint. This paper explores the potential and challenges of this approach when applied to structural body-in-white components. The methods for tailor rolling, tailor welding and hot stamping are described and applied to the production of a 7075 aluminum alloy B-pillar. The results are discussed in terms of feasibility and weight savings."

Jan 1, 2018

By I. Southern, S. Kelebek

"Smelting furnace bricks contain significant quantity of base metals trapped in refractory material. A series of flotation tests were carried out on samples of old bricks from Sudbury area to examine upgrading behaviour for recycling purposes. Depending on the grind size used nickel recoveries varied from 60 to 90.6% with corresponding grades of 20% and 14.7%Ni. There is a trade-off between nickel and copper. The nickel has responded well to fine grinding, however, the copper recovery suffered from it. Mineralogical characteristics and flotation behaviour of the brick material are discussed in reference to those from the primary ore. INTRODUCTIONMineral processing is well recognized as a mature technology not only for the mining industry, but also for the environmental industry for the purpose of remediation and recycling. Materials available for recycling are usually the products of many years ago. There are multiple stake holders in this area. In general, when the processing results in a product that can be reused or sold, the company carrying out the remediation makes a profit, while the regulators and the public are pleased due to a cleaner environment. From these points of view, there have been many papers published over the years on various mineral processing techniques applied to separation of many different materials including from mining and metallurgical industries (Wilson et al., 1994; Tsunekawa et al., 2005; Saikia et al., 2012).Flotation may be viewed as the backbone of the mining and metallurgical industry since its invention for separation of solids from one another almost a century ago. It is capable of recovering a variety of finely divided different solids following their liberation from each other. Its versatility and highly competitive nature in terms of cost per tonne of material processed, accounts for its occasional uses in the environment engineering area. In the mining industry, flotation is the standard method used for the sulphide ores. It can be applied as a bulk flotation and/or differential flotation. Bulk flotation, which refers to co-flotation of several components from their source, is most suitable for environmental cleanup objectives. Desulphurisation of various plant tailings is a typical example of this (Benzazzoua et al., 2000)."

Jan 1, 2012