Search Documents

By F. Mallozzi

"With the requirements of air pollution codes becoming more and more critical, the role of the ventilation engineer in industry has become an extremely important one. The ventilation engineer must provide the expertise for the selection of equipment and the design of systems which will reduce pollution to an acceptable level. Because pollution control systems involve considerable capital and operating expense, he must have the ability to select, from a wide range of products, the collector which will provide the required performance with a minimum of down time for maintenance. This paper discusses the principles of wet collection and the forces used to separate particulate matter from a gas stream. Important factors in the selection of equipment, such as collection efficiency, horsepower requirements and water consumption for the various types of collectors, are discussed in detail, as well as the construction features normally incorporated to circumvent potential problems."

Jan 1, 1971

By Hani S. Mitri

Overhand cut-and-fill mining of narrow vein orebodies inevitably leads to the creation of horizontal pillars. As the thickness of the overlying crown pillar diminishes, stresses build up in the pillar. More often than not, this situation causes an increased level of seismicity and possible pillar burst. One well-known strategy to reduce the hazard of crown and sill pillar burst in cut-and-fill vein mining is that of destress blasting. The paper first reviews the methods used for the monitoring and assessment of potential pillar burst in narrow vein cut-and-fill mining. The influence of horizontal stress, mine depth and pillar thickness on stress build-up in the crown pillar is examined through a characteristic narrow vein numerical model. The paper then presents, with reference to three mine case studies, the benefits of destress blasting and the factors affecting its success as a ground control technique.

Oct 1, 2001

By David J. Forrester

Light metals, most commonly aluminum, magnesium and titanium, and alloys containing them, are used in many industrial applications where lightness, hardness, ductility and resistance to corrosion are needed. However, these metals and their alloys can be potential ignition sources in underground coal mines. There have been documented cases in the past where coal mine explosions have been attributed to firedamp/coal dust ignitions involving light metals or their alloys. When light metals and their alloys are brought into contact with oxygen bearing material, such as iron oxide (rust) in the presence of heat, then a "thermite" reaction can occur. This source of heat can be generated from frictional contact or from merely a glancing blow. This paper outlines the hazards associated with light alloys, how to address the hazard and regulatory aspects.

May 1, 2001

Roasting of molybdenite concentrate is an important stage in the production of commercial molybdenum trioxide. The oxidation kinetic and mechanism of molybdenum sulfide concentrates from two plants were investigated at temperatures from 444 °C to 640°C. The rate of reaction was determined for thin layer samples in a muffle furnace at controlled temperatures, oxygen excess and removal of sulfur dioxide. For both concentrates the rate of reaction is fairly slow at temperatures below 500°C and remains fairly constant from 540 to 600 °C. It was observed that the concentrate from the first plant presents a tendency for sintering or glazing at temperatures above 620°C, whereas the same phenomena was observed at 20 or 30 °C higher temperature for the second concentrate. A kinetic model of two reactions, involving the formation of Mo02 as intermediate oxide for the production of Mo03 is proposed and activation energies of 23.0 and 20.8 kJ/mol for the first and second reaction were calculated for temperatures between 520 °C to 600 °C. These low values of activation energies indicate that the overall rate of oxidation is controlled by mass transfer, particularly in a porous layer of oxides. Therefore, the renewal of the surface by mixing and motion of the concentrate layer is of great importance. Sublimation of Mo03 becomes significant for temperatures above 650 °C.

Jan 1, 2007

By M. Kane, B. Bissonnette, D. Hodouin

"A laboratory cell has been designed for a careful investigation of gold ore cyanidation using mathematical modelling of the process kinetics. The cell is a stirred vessel with continuous monitoring and control of pH, oxygen and free cyanide contents. Samples are automatically extracted for gold analysis. The instruments are connected to a microcomputer which records all the measured variables and calculates the reagent consumption (air or oxygen, cyanide, lime). For cyanide control a sample is automatically extracted and filtered and the solution analyzed, using a specific electrode, by a flow injection technique. The rate of gold dissolution is modelled using a kinetic model the parameters of which are calculated by a non linear least-squares technique. The parameters of an empirical model of reagent consumption are also estimated. The resulting model is used in a simulator for gold cyanidation plant design, tuning and control.INTRODUCTIONThe leaching of gold ores in a cyanide solution is the usual method for gold extraction from raw ores. This process requires long reaction times and leads to very significant consumption of cyanide. The optimization of the cyanidation plant operation is a very important aspect of gold ore processing for increasing gold recovery and decreasing operating costs. The key parameters to the improvement of gold extraction are the selection of an efficient solution chemistry, the design of the size and the arrangement of the equipment and the correct tuning of the operating variables. Automatic control strategies can then be applied to maintain industrial operations at their optimum setpoints.Two approaches can be used for optimizing design and control of cyanidation circuits, either empirical trials for improving process performances or mathematical modelling of the process kinetics for subsequent analysis, simulation and optimization. The advantages of the second approach, which is used in this study, is that it gives a systematic pattern to interpret data and reliable tools, in as much as the models are good, to improve operation performances. In order to determine the structure and the coefficients of cyanidation models, well controlled measurement and calibration procedures must be used. The purpose of the paper is to present an equipment and a test procedure for modelling the kinetics of gold ore cyanidation."

Jan 1, 1990

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, 'longwall' and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By Balakrishnan Nanthakumar, Marek Pawlik, Dennis Grimm

"The anionic flotation of a high-iron phosphate ore from Agrium - Kapuskasing Phosphate Operations was investigated through batch flotation tests in the presence of soda ash. The flotation data were supplemented by titration of the flotation pulp with soda ash, analysis of process water chemistry, and determination of the mineralogical composition of the ore. The results of lab tests were applied to the flotation circuit design allowing the flotation plant to efficiently process problematic ores. Process control measures (pH, conductivity) were also developed.Calcium cations and sulfate anions were identified as the dominant ions present in the process water when the difficult-to-process ores are beneficiated in the flotation plant. The concentrations of calcium and sulfate ions were consistent with the presence of a small amount of a calcium sulfate mineral in the ore although an oxidation/weathering process of iron sulfide minerals present in the ore could also be responsible for the observed water chemistry and subsequent flotation problems with the ores. The latter possibility suggests that the long-term stockpiling of such ores may have a highly negative impact on the flotation process.The role of soda ash in the flotation circuit is to precipitate metal cations from the pulp thus allowing the tall oil-based collector to selectively interact with the phosphate components.INTRODUCTIONPhosphorus minerals are the main source of this element for the production of fertilizers, and the froth flotation process is the most important technology for beneficiating phosphate ores. The flotation concentrate from Agrium-Kapuskasing Phosphate Operations (KPO) is transported to Redwater Fertilizer Operations in Alberta (also operated by Agrium) where the phosphate concentrate is converted into a phosphate fertilizer and other important chemical products. The KPO phosphate ores differ widely in mineralogy and phosphate grades, and are broadly divided on-site into three classes. The easy-to-float A-type ores do not pose any major flotation problems, but the B-type and “marginal” ores, which are quite common in the KPO igneous phosphate deposit, are not always readily-floatable using the current reagent suites and process parameters (pulp density, feed particle size, pH). In fact, marginal ores are presently considered impossible to process by flotation. A-type ores contain normally more than 15% P2O5 and less than 8% ferric oxide equivalent (Fe2O3). B-type ores are approximately of the same P2O5 grades as A-type ores but their iron content may reach 30% Fe2O3. Any material containing less than 15% P2O5 is rejected as waste rock."

Jan 1, 2008

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By D. R. Lentz, S. H. Mcclenaghan, J. A. Walker

"Abstract - The Orvan Brook deposit is one of several (Zn+Pb>>Cu)-rich sulfide deposits hosted by the Spruce Lake Formation (California Lake Group) in the northwestern part of the Bathurst Mining Camp. This parautochthonous deposit is hosted by a narrow band of highly deformed, locally graphitic shale that appears to conformably overlie felsic volcanic rocks of the Spruce Lake Formation, and is in tectonic contact with overlying mafic volcanic and related sedimentary rocks of the Canoe Landing Lake Formation. The Spruce Lake Formation is dominated by felsic volcanic rocks and subordinate fine-grained sedimentary rocks, and mafic volcanic rocks (Canoe Landing Lake member). The felsic volcanic rocks can be divided into aphyric and feldspar-phyric rock types. The feldspar-phyric rocks and a few of the aphyric varieties have a Zr/TiO2 ratio of 0.06, and fall into the California Lake Group field on a Y/TiO2 versus Zr/TiO2 diagram. In contrast, the aphyric felsic volcanic rocks have Zr/TiO2 ˜ 0.09 and are marked by high Zr and Th, which is consistent with highly fractionated felsic magma of Spruce Lake affinity. Major and trace element analyses of host rocks suggest that weak to moderate hydrothermal alteration developed on the south side (stratigraphic footwall) of the deposit, which is consistent with a north-younging succession. The sulfide lens strikes east-west for approximately 2.3 km, extends down-dip for at least 500 m locally, and has an average thickness of between 0.75 and 1 m, but is locally up to 5.5 m thick. The contacts of the massive sulfide lens with its host rocks are invariably sharp. Host rocks show evidence of intense ductile deformation as well as later brittle deformation. Compositional layering and sulfide breccia textures in the sulfide body are interpreted to result from deformation or tectonic enhancement of original primary layering. The deposit contains an estimated resource of 2.69 Mt grading 1.73% Pb, 5.95% Zn, 0.37% Cu, 72 g/t Ag, and 0.9 g/t Au. Similarities in bulk d34S between the Orvan Brook (+8.6‰) and the nearby Cu-rich McMaster deposit (+8.2‰) suggest a common depositional setting."

Jan 1, 2006

By André Piché

"Over the last ten years, several developments have been undertaken to conceive a machine capable of carrying out simultaneously all the mining tasks in hard rock deposits: cutting, mucking, hauling, ground support and dust control.The main advantages of continuous mining over conventional drill and blast is the elimination of the cyclical nature of the actual methods. Other advantages sought are improved stability of mine openings, higher productivity, lower costs, and a cleaner and safer mining environment. Noranda has con-tributed to these developments in a major way. As a member of HDRK, Noranda participated in the development of two mechanical continuous mining machines; the TM60 and the Wirth. Noranda also undertook a development of its own based on the utilization of electricity to break rock. This technology is called plasma blasting (PBT). The concept of plasma blasting is illustrated in Figure 1.When the operating voltage is reached (18kV), the energy is released through a high current switch (500k A) into a coaxial powercable. It is then delivered to the tip of an electrode inserted into a drill hole which is filled with an electrolyte (water). When the energy reaches the electrolyte, it is instantaneously transformed into a high temperature, high pres-sure plasma that produces a shock wave capable of breaking rock(1).After initial testing of the plasma blasting technology in the lab and in the feld, two experimental platforms were constructed. The first one, a test bench, was erected at the Noranda Technology Centre in Pointe Claire, Quebec.(2)The second one is a rock breaker prototype based on a standard diesel-powered carrier (Fig. 2). Each platform was equipped with a 300 kJ pulsed-power module.In 1993, the rock breaker prototype was used for an extensive series of tests in the field. During that campaign, over 700 oversized boulders were blasted. The results of the tests demonstrated that more durable components for PBT were needed. The test bench was then used to successfully develop and test long-lasting components (probe, switch, cable, connector) that can be adapted to industrial platforms leading to the commercialization of the technology."

Jan 1, 1996

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016

By K. Torigoe, S. Owad, C. Tokoro, Y Tsunazawa

The mechanism of an abrasion process to recover metal values by removing components from printed circuit boards (PCBs) is modeled using a discrete element method (DEM) simulation. To simulate the abrasion process, a model PCB geometry was constructed consisting of bonded particulates. The simulation allowed connections between particles to be broken if the bonding force calculated from DEM exceeded a threshold level. Simulation results were compared with experimental comminution data using an agitation mill with test PCBs on which nine capacitors were surface solder-mounted. Simulation results obtained from the DEM with the anchoring model corresponded to experimental observations.

Jan 1, 2011

By L. Henry Smith, David C. Arthur

"The Williams Mine is Canada’s largest gold producer, with annual production of 450 000ounces from 2 300 000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs.The mine ventilation system is modified to include a new vent raise and variable pitchvane-axial fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved.Heating costs associated with under-ground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, minewater and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors.System design, energy savings data and payback calculations are presented."

Jan 1, 1996

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By John Kruse, Sethu Raman, Dave Tenney

The Cullaton Lake B-Zone gold mine was the first gold producer in the Kaminak Subprovince of the Canadian Shield . Located approximately 650 km north of Thompson. Manitoba, the mine produced 77,783 ounces of gold and 5,564 ounces of sil ver from 251 ,236 tons of ore during 1981-84 period. The depos it is a small , structurally controlled , stratabound orebody in an Archean iron formation. Most gold occurs in sulphide and silicate fac ies. Based on new ev idence, the depos it is interpreted to have fo rmed by remobilization of syngenetic low-grade gold mineralization in the iron fo rmation in a favoura ble fold structure. The concept and methods developed at the mine have been successfull y applied in the discovery of new deposits in the area. One of the concepts. which link Archean and Proterozoic mineralization. may have wider applications in the search fo r gold deposi ts elsewhere in Canada .

Jan 1, 1986

By E. Stansfield

Coal samples are sometimes taken from a wet spot in a mine, or from an open car or pile shortly after rain, and submitted for analysis in a dripping wet condition. Other samples are taken from a dry spot in the mine, or from an open car or pile after a period of dry weather. Comparison of the analyses obtained in the two cases would be absurd, although the samples might be of essentially the same coat apart from the surface moisture on the one. The analyst therefore attempts to reduce all samples to an equal basis by the operation known as air-drying. Air-drying is practised by the chemist for three reasons: (1) To make it possible to grind the coal to powder. (2) To bring the coal sample to a condition in which it will not change in weight rapidly whilst portions are being weighed out for analysis -in other words, to bring it into equilibrium with the air in the laboratory. (3) To determine the water-retaining power of the coal. Any kind of drying is satisfactory for (1); the coal should be dried more or less according to the humidity at the time in the laboratory for (2); whilst it should be always dried to the same extent for (3). In other words, no method can be satisfactory for both (2) and (3). In this paper the only question considered is (3) -that is, air-drying the coal under standard conditions so that strictly comparable results can be obtained for the water content of coals after air-drying. After a sample of wet coal is exposed, it loses moisture until it is in equilibrium with the air at the time: thus the coal will loose distinctly more water in air of 20 per cent relative humidity, for example, than it would in air of 80 per cent.

Jan 1, 1923

By P. P. Rosario, D. M. Maijer

The primary crusher is a key component in the comminution process applied in open pit mines. A collaborative research project between the University of British Columbia and Highland Valley Copper (HVC) was conducted aiming at understanding gyratory crusher liner wear in the overall context of the crushing process. This paper presents an analysis methodology applied to data collected using a laser-based tool for assessing wear in gyratory crushers. Data from the wear measurements was correlated with crusher production information such as current draw and throughput. As a result of the knowledge developed during this work, an innovative way to evaluate crusher liner profiles was created and new mantle profiles were designed. This led to a reformulation of HVC’s standard liner management policy with a resulting estimated annual savings of 13% in total crusher liner cost and a 15% reduction in liner replacement downtime.

Jan 1, 2006

By T. Thriveni, Ji Whan Ahn

"The current advanced technologies for the manufacture of light weight metals processing significantly increasing and attributes to the safety, performance, recyclability and economy. Still lack of technologies developed for light weight metals processing waste utilization and application. Environmentally friendly methods need to develop for better understanding the processing waste utilization. Alumina and aluminium processing creates a wide range of waste products, the most significant being is red mud. Bauxite residue is a high volume hazardous waste and nearly 3 billion tons have been dumped worldwide. Approximately, 120 Million tons/yr of red mud being produced without any environmental sustainable solution. Currently the most significant technology is waste utilization. The bauxite residue is suitable for road base construction, golf bunker sand, back fill and, general fill. Sustainable recycling technologies are necessary for the bauxite residue utilization for the recovery of rare earth elements and cement materials. Carbonation or CO2 sequestration of carbon dioxide is a method pioneered for the bauxite residue is modified to reduce alkalinity. The carbonation of alkaline material is an inexpensive and safe process that leads to the formation of thermodynamically stable products. The use of the carbonation can be an advantageous solution for environmental climate change and sustainability problems in the new century.INTRODUCTIONIn 2014, bauxite consumption was estimated to be 9.6 million tons, nearly all of which was imported, worth an estimated 269 million dollars. More than 95% of the bauxite was converted to alumina, and the remaining 5% went to non-metallurgical products, such as abrasives, chemicals, proppants, and refractories. Global aluminum demand is growing steadily spurred by growth in India and China (RBCAluminum Market Outlook, 2013) (Figure 1). Aluminum consumption is expected to rise 5% annually through the end of the decade, reaching 67 million tons per year by 2020. Global bauxite production decreased by 17% from that of 2013, principally owing to lower production in Indonesia. In response to a Government ban on exporting bauxite and other unprocessed mineral ores that took effect on January 12, 2014, bauxite mines throughout Indonesia shut down and production decreased from 55.7 million tons in 2013 to an estimated 500,000 tons in 2014. The ban was part of a mining law that was instituted in 2009 to increase development of downstream processing facilities in Indonesia."

Jan 1, 2016

By S. Chung

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick mine. Over the past 30 years, two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 Mt of ore and the North Regional Pillar has about 3 Mt of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass de-stress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success, the mine decided to take a similar approach to de-stressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state-of-the-art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica’s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

Jan 1, 2005

By Jim Truskoski, Alain Bouchard, Andy Kerr, Germain Labonté, Jim Barrett

"Improving mill grade recovery relationships is always good business. INCO’s Clarabelle Mill has just undergone a $16 million process upgrade that was designed to improve nickel recovery by 2%. The “Mill Redesign Project” was completed on time, under budget and delivered the promised improvement in recoveries.This paper describes the methodology of the Mill Redesign Team, details of the process improvements and the critical success factors that helped the team deliver on its promises.With a payback of under one year, the Mill Redesign Project will play a key role in ensuring a competitive edge as INCO embarks on its second century of operation.INTRODUCTIONIt is not uncommon in milling operations to encounter a crisis. That is the point when the process does not behave as expected and fails to respond to the increasingly desperate efforts of the metallurgists and operators. Flowsheet and process changes are attempted and abandoned. With luck, one or more of the changes achieves some mitigation of the original problem or more usually, the original cause of the problem disappears. Regardless, the metallurgist can sit back and bask in the apparent success of his or her endeavours.Less common is when a problem is carefully diagnosed, a team put together to explore all avenues and recommend a path of action that is implemented on time, on budget and immediately delivers on the promises which are sustained over time. This is one such story. It is the story of the Mill Redesign Project at INCO’s Clarabelle Mill in Copper Cliff, Ontario.BACKGROUNDThe Clarabelle Mill was built in 1971 on the southern rim of the Sudbury basin. At that time it was one of four mills operated by INCO in the Sudbury area. During the 1970’s, 80’s and 90’s, the need for increased process efficiency, higher levels of sulphur rejection to tails and the concurrent development of high capacity mills and flotation cells, resulted in the consolidation of INCO’s Sudbury area milling operations into a single, expanded facility at Clarabelle."

Jan 1, 2003