Search Documents

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By Edward R. T. Tiekink

Metal complexes continue to find therapeutic applications for the treatment of a wide variety of human ailments. Amongst these, gold(I) thiolates are used to treat rheutmatoid arthritis but, usually in combination with other treatment or as a last resort. New therapeutic uses of gold, both as gold(I) and gold(III), are being sought, including against cancer, the focus of the present contribution. It will be demonstrated that certain gold(I) complexes show exciting cytotoxicity profiles, rivalling those of cisplatin and standard chemotherapeutic agents. More importantly, anti-tumour activity is demonstrated in vivo, albeit in a mouse model. The presentation will give a brief overview of ?metals in medicine? with a focus on gold and will summarise some recent advances in the development of goldbased anti-tumour agents.

Oct 1, 2003

By Michel Robert

"In 1974, Copperfields Mining Corporation and Soquem formed a new company, Niobec Inc, to bring the niobium deposit of the St-Honore carbonatite into production.St-Honore is located in the Saguenay area, near the cities of Chicoutimi and Arvida, and about one hundred and forty (140) miles north of Quebec. The discovery of the carbonatite complex was made in the fall of 1967 as a result of an airborne radiometric survey in search of uranium. The detailed exploration of the carbonatite indicated two niobium-bearing formations besides the original discovery of a rare earths zone. During the following years, the niobium formations were defined by diamond drilling and a decline was driven down to obtain adequate samples for metallurgical evaluation. In 1974, after seven hundred (700) bench scale tests, eleven (11) months of pilot plant 2nd a worldwide market research, a joint decision was made to initiate the development of a fifteen hundred (1500) T.P.D. mine and mill, under the management of Teck Corporation. The construction of the facilities were completed in early 1976 both on time and within budget. Niobec is now the only north american and the world second largest producer of Niobium concentrate.The process used at Niobec was developed from the pilot plant programs and later modified by the mill personnel. A simplified flowsheet for this process is shown on the slide. Briefly, run of mine ore is crushed to minus 5/8"" and fed to a rod mill, ball mill, and screens circuit where the ore is ground to 92% passing 65 mesh. The ore is deslimed in two stages of cycloning, and the final cyclone overflow at 85% minus 11 microns goes to waste. The cyclone underflow is conditioned prior to flotation of a carbonate-apatite concentrate. This concentrate is cleaned twice and then pumped to tails. The carbonate rougher and cleaner tails are cycloned in two stages to change the process; water and then sent to the pyrochlore rougher flotation. The rougher concentrate is cleaned five times. This is followed by pyrite flotation to remove sulfur, leaching with hydrochloric acid to remove phosphorus and dyed to less than 0.1% moisture before being sent to packaging."

Jan 1, 1978

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By W. G. Worcester

Generally speaking, the term 'clay' appears to convey but little to the average layman other than of a sticky substance to be rigidly avoided when making a cross-country drive in the family ark- especially so if the chains have been left behind. On the other hand, the technical ceramic; engineer, though his chariot be bogged in the self-same mud-holes, will, more than likely, be planning on ways and means for the conversion of the troublesome gumbo into paving bricks over which all might ride with pleasure and security. However, to come to the point, the term 'clay' bears much the same relation to the ceramic world that the term 'ore' does to the metallurgical; in other words, as there are many kinds of ores, so also are there many kinds of clays, and it therefore becomes necessary to classify and sub-classify them previous to a discussion of their relative values and importance. Hence, a brief digression will be made from the main topic of this paper in order to enumerate and classify a number of the more important types of clays. By so doing, the relative position of Saskatchewan clays, later discussed, will be better understood.

Jan 1, 1929

By Neri Roux, Ross Gilders, Yemi Oyediran, Leo Cheung

Quest Rare Minerals Ltd. is developing their Strange Lake B Zone REE deposit located in Northern Quebec. An extensive batch bench scale testing program was launched to investigate open circuit rougher flotation performance under different conditions. The objective of the flotation study was to demonstrate the effectiveness of rejecting gangue minerals to flotation tailings while concentrating rare earth elements as well as yttrium, zirconium, and niobium into a concentrate suitable for further hydrometallurgical processing. Mineralization of interest at Strange Lake occurs within peralkaline granite-hosted pegmatites and minor aplite. The REE and high field strength element (HFSE)-bearing phases are hosted primarily in pegmatites as relatively fine-grained phases or pseudomorphs. The gangue phases comprise of quartz, feldspar, amphibole, and pyroxene. Potential ore minerals comprise predominantly of kainosite, gerenite, gadolinite, zircon, pyrochlore, and gittinsite. These complex mineralogical characteristics increase the difficulty for processing and provide a challenge for choosing the correct reagent scheme in rougher flotation. Process options including reverse flotation to reject the gangue minerals and de-sliming prior to the direct rougher flotation were investigated. Optimization trials were conducted using various reagent regimes and under different flotation conditions. Encouraging results were found using a combination of collector reagents supplied by Cytec Canada Inc.

Jan 1, 2014

By K Byrne, W. Hawker

The average grade of copper concentrate is steadily declining, forcing the industry to turn to lower grade and metallurgically challenging orebodies. When faced with a low grade, challenging ore, mining companies are often forced to choose between high recovery at low grade or low recovery at high grade. Hydrometallurgical processing of copper concentrates using metathesis reactions, which replace iron with copper in copper-iron sulphide minerals and increase the copper to sulphur ratio in copper sulphide minerals, provide an opportunity to upgrade copper concentrates and potentially allow high copper recovery for a high grade concentrate. Factors such as concentrate mineralogy, reaction time and temperature, and the concentrations of copper, chloride and acid in solution are reported to affect the reaction extent and mineral phases formed by metathesis. In this paper, a copper concentrate has been studied over a wide range of conditions to investigate the influence of these key parameters on the extent of copper metathesis reactions and product phases formed. Solution and solid phases are assayed with the main mineral phases identified by Quantitative X-Ray Diffraction. INTRODUCTION The minerals present in copper deposits determine the prospective processing options either: pyrometallurgical or hydrometallurgical. For copper oxide ores, copper is typically present as oxides, carbonate, chlorides, silicates and sulphates. These minerals are readily solubilised in acid and are usually treated through hydrometallurgical processes. The typical process route for copper oxides is to leach copper into aqueous solution, purify and upgrade the solution phase through solvent extraction and then recover copper as metal by electrowinning (Davenport, King, Schlesinger, & Biswas, 2002). Copper sulphide deposits may contain a multitude of copper bearing minerals, including chalcopyrite, bornite, enargite, covellite, digenite and chalcocite. The copper ore grade and treatment options are affected by the mineral type and distribution. Sulphide ores are typically treated through comminution and mineral flotation to form concentrates, followed by pyrometallurgical smelting. Hydrometallurgy can also be used to process sulphides depending on the mineralogy and impurity levels (Davenport et al., 2002). The trend of decreasing copper grade with increasing impurity levels are common across the mining industry and pose future challenges to copper processing. This trend has prompted research into hydrometallurgical options for upgrading copper concentrates. One promising hydrometallurgical option is using metathesis reactions. Metathesis reactions, sometimes also called double replacement or displacement reactions, are chemical processes involving the exchange of bonds between two chemical compounds or species. In this case, the metathesis reactions involve copper in solution exchanging with cations in the solid sulphide concentrate. The driving force for copper sulphide metathesis is the relative affinity of the exchanging cation elements for sulphide. Based on sulphide precipitation diagrams, the expected order of affinity for sulphide should be Hg2+ > Ag+ > Cu+ > Cu2+ > Bi3+ > Cd2+ > Pb2+ > Sn2+ > Zn2+ > Co2+ > Ni2+ > Fe2+ > Mn2+ (Monhemius, 1977). Hence, copper metathesis reactions are capable of increasing copper content and removing impurities such as iron, nickel, zinc and lead from copper concentrates.

Jan 1, 2019

By Marie-France Caille, Carl Caumartin

"Audrey Resources' Mobrun Mine is located in Dufresnoy Township some 30 km to the northeast of Rouyn-Noranda. The Mobrun tine deposits consist of two major massive sulphide lenses; the newly discovered 1100 lens located 450 m south of the Main zone, and one ntellite lens, the 850-870-930 complex.The 1100 lens is hosted in a large pyroclastic unit bounded to the mouth by rhyolite and andesite flows and by a thick rhyolite unit to the art h. stratigraphically belon the three lenses. It consists of approximately 15 Mt of massive sulphide, of which 10.4 Mt are of economic ade. The Main lens lies comformably above thick rhyolite flows, ecciated and pyritized by the sulphide horizon, and is overlain by ttercalated ash tuffs and rhyolites which host the over-lying satellite ns. The Main lens consists of 3,3 Mt of massive sulphide, of which 523 000 tgrade0.80% Cu, 2.44%Zn,30.19 g/t Ag, and2.2 g/t Au he richer satellite lens (180 000 t) is part of the same volcanic stem and resulted from a resurgence of hydrothermal activity. ructure played a role in the final geometry of the deposits but did not eatly affect the volcanogenic and stratabound nature of the lens. Total production since the start of operations in 1985 amounts to 58 000 t and is restricted to the Main lens. Production from the 100 will come onstream in 1992 as ore reserves from the Main and e satellite lenses are exhausted.RESUMELa Mine Mobrun de Ressources Audrey inc. est située dans le mton Dufresnoy, a quelque 30 km au nord-est de Rouyn-Noranda. lle comprend deux lentilles de sulfures massifs d’importance majeure ~i sont les lentilles 1100 et Principale, et une lentille satellite qui est complexe 850-870-930.La lentille 1100, la plus ancienne, est contenue dans une épaisse 1ite pyroclastique bordée, au sud, par des coulées de rhyolite et d’andésites, au nord, par une épaisse unité rhyolitique. Cette lentille contient environ 15 Mt de sulfures massifs dont 10,4 Mt à teneur économique. La lentille Principale repose sur d’épaisses coulées rhyolitiques brechifiees et pyritisees à proximité de l’horizon de sulfures; elle est recouverte de tufs a cendres et de rhyolites interlitees qui contiennent la lentille satellite. La lentille Principale est constitute de 3,3 M t de sulfures massifs dont 1 523 000 t sont économiques avec une teneur moyenne de 0,80% Cu, 2,44% Zn, 30,19 g/t Ag, et 2,2 glt Au. Faisant partie de ce second épisode volcanique, la riche lentille satellite (180 000 t) temoigne d’une recrudescence de l’activité hydrothermale. La structure joue un rôle important dans la géométrie finale des dépôts mais ellen' affecte pas, de fa~on significative, la nature volcan génique des lentilles. Depuis le début des opérations, en 1985, la production totale est d’environ 568 000 t, provenant essentiellement de la lentille Principale. La mise en production de la lentille 1100 est prévue pour 1992, alors que les réserves des lentilles Principale et Satellite seront probablement épuisés."

Jan 1, 1990

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By Joseph Licavoli, Paul Sanders, Yang Yang

"Al-Sc-Zr alloys form thermally stable L12 precipitates which provide high temperature strength. Although the overall fraction of L12 Al3Sc and Al3Zr may be increased by increasing scandium (Sc) and zirconium (Zr) content, such additions may increase primary phase fractions and do not produce desirable secondary phase morphologies. Rapid solidification techniques, such as melt spinning, increase solute atom concentration within the matrix. When the supersaturated matrix is aged, higher precipitate volume fractions at low Sc and Zr levels can be achieved improving high temperature strength. Melt spinning was used to rapidly solidify (107 k/s) a thin ribbon of Al-0.5Sc-0.4Zr at. %. The ribbon was compacted and extruded into 99.8% dense rods, and then aged using multi-step isochronal heat treatment up to 600°C. Precipitation strengthening was evaluated by ambient hardness measurement. The ambient hardness of melt-spun ribbon after precipitation hardening increased by 450 MPa (~67% increment) during isochronal heat treatment.INTRODUCTION Small Sc and Zr additions to aluminum improve strength and creep resistance above 300°C due to tri-aluminide precipitation of Al3(Sc,Zr) in L12 structures similar to ??, Ni3(Al,Ti) in nickel superalloy, but the Al3(Sc,Zr) particles have a Sc-rich core surrounded by Zr-rich shell (Figure 1). The Al3Zr shell limits atomic transport between the Al3Sc core and the matrix and reduces coherency strain. These factors reduce precipitate coarsening rate at elevated temperature (Bergner & Van Chi, 1977; Fujikawa, 1997; Knipling et al., 2011; Clouet et al., 2006).Figure 1. Simplified schematic model of precipitate Al(Sc,Zr) in Al-Sc-Zr alloy. Shell is rich of Al(Zr) intermetallic phase, particle core is rich of Al(Sc) intermetallic phase (after Voorhees, 2006). Numerous Al3(Sc,Zr) particles increase alloy strength and creep resistance as the precipitates impede dislocation glide and to a lesser extent climb. Previous work on ternary Al-Sc-Zr alloys show large strength increases versus binary Al-Sc, and Al-Zr alloys in Table 1."

Jan 1, 2018

By W. O. Karvinen

"In the Timmins area, a close spatial and chronological association exists between gold deposits and two major stratabound carbonate-rich members and related quartz-feldspar porphyries. Synvo/canic and metamorphogenic are the two main types of mineralization recognized. Synvolcanic ores include the stratiform quartz-ankerite ""veins"", pyritic carbonates and chert-carbonate-tuff sedimentary rocks and epigenetic ventrelated breccias and stringer zones. Metamorphogenic ores consist of quartz-carbonate fracture fillings in dilatant zones developed during various phases of regional deformation and metamorphism. They are classically epigenetic in character.The evidence suggests a primary syngenetic enrichment of gold on the ocean floor and in vent areas during submarine felsic volcanism and related exhalative-hydrothermal activity followed by further enrichment into quartz-carbonate stockworks during regional deformation and greenschist metamorphism.Although normally thin (a few hundred metres), carbonate members in Archean volcanic terrain represent intense hydrothermal activity which could have transported and enriched gold. They should be used to locate fossil vents and structurally favourable zones where economic concentrations of gold may be found."

Jan 1, 1982

By R. Tyreman, G. Ritson

"The Red Lake Mine is situated in Balmer Township, Red Lake area in northwestern Ontario. It is an underground mine that has been in production since 1948. The property was originally known as the Dickensen Mine and was shut down in 1996.A feasibility study was carried out in 1998 and it was determined that a new mill should be constructed with a throughput rate of 600 stpd. The life-of-mine average gold grade was projected to be 1.35 oz/t with gold predominantly associated with arsenopyrite and pyrite. Metallurgical testwork indicated that the optimal flowsheet for gold recovery would include an autoclave for oxidation with a carbon circuit for adsorption. To limit capital cost and establish cashflow, the mill was constructed without an autoclave. The recovery by gravity and cyanidation was projected to be 83%. A flotation plant was constructed at the tail end of the circuit to recover the additional gold associated with sulphides from the leach circuit tailings. This material is being stockpiled onsite for future oxidation treatment.Detailed engineering was started in early 1999 and the first gold was poured in August 2000. One feature of the project was the use of Contact Lake equipment from Cameco’s Contact Lake project. The entire mill was purchased and equipment re-used where possible. The capital cost for the process facilities was C$3 1.5 million."

Jan 1, 2001

By A. M. Krzanowski, T. S. Golosinski

"This paper presents results of a study undertaken to determinethe feasibility of mining plains overburdens with bucket wheel excavators. Based on extensive geotechnical testing of overburdens under study, the relations between material geotechnical properties and its cuttability were defined. The properties with the highest correlations to the cuttability werethen used to develop the material diggability classification. This classification may be used for identification of overburdens and coals mineable by bucket wheel excavators.IntroductionLow cost of mining and high productivity can be achieved when mining unconsolidated soils and soft rocks with bucket wheel excavators. As a result this mining equipment will likely be introduced into plains coal mines. At present there are plans to use a bucketwheel excavator (BWE) in at least one mine by the end of this decade. Unfortunately, the performance of a BWE deteriorates rapidly with the increasing strength of mined material. To avoid costly misapplication, material diggability must be defined in advance of an application (i.e. the force required at the cutting edges of BWE buckets must be quantified). Correct definition of material diggability permits reliable selection of a BWE, or may indicate unsuitability of this equipment for a particular application.The reported studyu i was undertaken to investigate the diggability of typical prairie overburdens and thus provide a guidance for likely future applications of bucketwheel equipment. Investigations concentrated on the parts of overburden most likely to create problems for a BWE mining. These are defined in Table 1. At present, thin layers of the two investigated materials (samples K and L) are mined by a BWE in an oil sand mine, after being loosened by blasting."

Jan 1, 1987

By Rene Cane, V. I. Lakshmanan, John Starkey, Richard May

"The Agrium Kapuskasing Phosphate Operation mines and processes up to 6,000 t/d of phosphate ore. Run-of-mine crushing to minus 6 inches is done in a toothed roll-crusher, while grinding is done in a SAG/ball mill circuit with no coarse recycle classification of the SAG mill discharge. The primary grinding mill is an 18 ft. diameter x 9 ft. EGL, 1500 HP variable speed SAG mill and the secondary mill is a 13 ft. diameter x 21 ft. long, 2000 HP fixed speed, ball mill. When hard ore was treated, the SAG mill restricted the tonnage that could be ground. When soft ore was treated, the ball mill and spiral classifier overloaded and restricted throughput.Recommendations from a plant benchmark and an ore hardness testing program, on how to better utilize installed energy in the Agrium SAG mill when treating soft ore, and how to obtain best results when treating hard ore, were checked in a pilot plant investigation in the 3 ft. diameter Starkey-PRO Pilot SAG Mill. Correlation between the ore hardness testing and the results from the 3’ Pilot SAG mill was very good. In addition, the work indicated the results that could be expected for the different ore types when using either smaller SAG discharge grates and/or a vibrating screen with 10 mesh square opening cloth.INTRODUCTIONAgrium Kapuskasing Phosphate Operation consists of a 6800 t/d open pit mine and a concentrator, near the Town of Kapuskasing in Northern Ontario. The two major ore types are sandy ore and cemented ore. Sandy ore is fine, soft and easy to grind in the SAG mill while cemented ore is harder, more blocky and difficult to grind in the SAG mill. The ratio of sandy to cemented ore in the deposit is thought to be in the order of 80:20 but can range as high as 5050, so it was important for the grinding circuit to have the ability to treat sandy ore alone."

Jan 1, 2002

By T. A. Lazier, C. S. Longley

"Paymaster Consolidated Mines, Limited, owns several groups of claims in various parts of the Porcupine district. The area in which mining has been carried on includes parts of lots 5, 6, and 7, con. 1, Tisdale township, and twelve adjoining claims in Deloro township to the south. Highway No. 67A between South Porcupine and Timmins crosses the property.The discovery of the Dome mine in 1909 caused a rush of prospectors to the district and in a few weeks practically all territory adjacent to the Dome was staked. At that time work was started on the West Dome, West Dome Lake, Apex, and Standard properties. These were consolidated in 1930 to form the present Company. Gold was produced from the West Dome Lake from 1915 to 1930, and from the Standard-Paymaster from 1922 to 1928. The total production of the previous and present companies from 1915 to November 30, 1946, has been 487,170 oz. gold and 149,342 oz. silver from 2,337,554 tons of ore."

Jan 1, 1954

By H. R. Banks

IF you have ever travelled in the valley lying between the Selkirks and the Rockies in the East Koorenay district, you will have noted that the former mountains are rounded and massive, while the serrated peaks of the latter, fingering into the sky, bring an entirely different. picture. These two mountain ranges, with the comparatively level valley between, serve splendidly to introduce the subject for discussion. It is rather strange that, despite the fact that wear is undoubredly the greatest force with which human ingenuity bas to contend, it has come in for very little study from the stand point of pure science. Empiricism has been the sole ally in the fight for improvement! That we may have a clear understanding as to what we mean by wear, I would include in the term the breaking dawn of ail solid matter, from the natural wearing dawn of the mountains previously mentioned, to the hale in the mill pipe-line, which forces one to shut-down-usually at some un-earthly hour-to carry out a repair. It seems a far cry from mountains to mill launders or pipe-lines, but, magnified sufficiently, most of the materials with which we have to deal would show surfaces not unlike those we see around us. The progressive steps of wear, or ?erosion' as our geological friends would prefer to term it, are exemplified in the two ranges of mountains and the valley between. True, the wearing dawn by natural forces is a slow process. The aeons which have passed since first these mountains were formed seem endless. The natural forces pitted against them seem puny in the light of the interminable rime that has been needed to effect the changes. But here, as in the case of the materials with which we are dealing day by day, the combination of many forces ultimately brings about that condition which we describe as 'worn out'. In the case of the mountains, it is when they are finally levelled into plains, and in the case of equipment which we use, it is when that equipment will no longer serve its purpose.

Jan 1, 1943

ABSTRACT The SART (sulphidization, acidification, recycle, and thickening) process is an effective way to separate copper and cyanide in the waste stream of gold processing plants using cyanidation. Factorial experimentation has been conducted to create models of copper recovery, cyanide recovery, acid addition, and oxidation/reduction potential during SART. Economic analysis of the resultant models showed that SART is best operated with a sulphide-to-copper molar ratio of approximately 0.56, pH of 4, and a minimized cyanide-to-copper molar ratio. The experiments also showed th0at residence time can have drastic impacts on SART performance.

Jan 1, 2013

By W. R. Tyson

IT HAS BEEN KNOWN for many years that alloy steels can become brittle when tempered in the range of 350-600°C, or cooled slowly after heating to higher temperatures. The metallurgical literature reveals that blacksmiths were aware as early as 1883 that water quenching was necessary after heat treatment above 600°C to avoid brittleness. It has also been known for years that the problem is associated with trace impurities; a paper in the Journal of the Iron and Steel Institute of 1894 refers to the brittle, faceted fractures that occur in steels containing arsenic, phosphorus or sulphur. However, definitive investigation of the mechanism of embrittlement has been possible only within the last decade with the introduction of new experimental techniques to investigate surfaces, especially Auger electron spectroscopy. It is now possible to study in detail the chemistry of surfaces with a resolution of an atomic layer or two, and enormous progress has been made recently in studying the segregation of impurities to grain boundaries by exposing the boundaries by fracture inside the microscope. A clear picture of the processes occurring and their interpretation is now emerging, as was particularly clear at the recent 1977 ASM Materials Science Seminar on Interfacial Segregation held in Chicago in October. Recent research in this area has pointed the way for commercial exploitation of this new knowledge and experimental technology. It is the purpose of this article to trace progress in understanding temper embrittlement and to indicate other areas where control of interfacial segregation and its effects can be important in metallurgical applications.

Jan 1, 1978

By Grant L. Anderson, Richard C. Rice, Richard L. Jentgen

"Data for underground mine-hoist ropes determined in the Ontario Special Rope Tests were obtained, encoded and analyzed statistically. Prior 10 refined statistical analyses, these data were subjected la characterization studies and preliminary analyses to allow trends to emerge that could be used to guide and facilitate the refined analysis. The data were characterized by determining distribution s for a wide range of variables including remaining strength, service life in terms of lime and hoisting cycles, outer-wire torsion values, elongation during tensile testing, diameter reduction, location of strength loss and the strength lasses associated with corrosion rating and lubrication rating , This paper describes the more important relationships between remaining strength (or, conversely, strength loss) as the dependent variable and some of the principal independent variables mentioned above.IntroductionBoth productivity and safety in underground mines could be improved if mine-heist rope Iife and reliability could be predicted more accurately . As a result, hoist-rope failure processes and their effects on rope life and remaining strength need to be quantified and related in such a way that improved retirement criteria can be developed. This is true whether the failure is incipient or actual or whether the failure mode is by corrosion , wear, fatigue or a combination of these factors."

Jan 1, 1984

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998