Search Documents

By Ron Hatch, M. K. Witte

"INTRODUCTIONThe proper selection of carbon for a gold carbon in pulp (CIP) circuit involves careful evaluation of several physical, chemical and economic factors. A series of evaluations are required to maximize gold recovery at the lowest capital and operating costs, whether the carbon is selected for an existing gold mill circuit or a new mill under design.Although evaluation may proceed through various stages, it is the intent of this paper to outline some of the preliminary testwork that should be carried out to screen potential carbons for a particular application.An examination of the specification sheets supplied by the various carbon manufacturers may indicate some desirable properties on which to make cursory selection. This exercise by itself will not provide the basic data needed for selecting the best carbon for a particular ore pulp and metallurgical circuit. The necessity of further metallurgical evaluation is indicated by the fact that different carbons perform differently depending on the physical and chemical nature of the leach pulp. In the case of an existing mill, actual leach slurries using mill water are available and should be used for testwork. In the case of new mills, leach pulps must be prepared to simulate the proposed circuit.Five coconut shell activated carbons were obtained from various suppliers, all reported to be 6 x 16 mesh carbons recommended for CIP circuits. A metallurgical evaluation was made utilizing two leach pulps with significantly different characteristics. This paper describes the test procedures utilized and the results obtained from the testwork."

Jan 1, 1985

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By Lionel A. York

THE first application of the cementation process took place in the year 1864, according to H. Standish Ball, when a break in the brickwork lining at a depth of 270', in one of the Rhine Preussen pits near Homburg, was sealed by running in milk of cement from the surface by means of a small hand pump. At about the same time Monsieur Portier adopted the method in France for repairing breaks in shaft lining. Figure 1 is descriptive of the Portier system and is of interest when compared with modern practice. During the next thirty years numerous attempts were made to improve the process; the general method used in sinking being to put clown bore holes outside the perimeter of the shaft for the purposes of injection. The cementation process was first recognized as an important as-set to mining in 1896 when Monsieur A. Francois developed his method of boring and injecting inside the shaft below the permanent water level. The Francois cementation process rapidly attained fame on the Continent and many shafts were sunk by its use in France, Belgium and

Jan 1, 1961

By S. Rash Ahmadi

One of the most important elements in power plants is rotors and repairing the damaged rotors is very important in view point of economics. One of the most complicated problems in power plants is increasing of stiffness of the turbine rotors. This problem which occurs mainly due to thermal shock or rubbing makes to exit damaged rotor from service. These elements can be repaired effectively by heat treatment methods. Tempering heat treatment is the most common solution for straightening of damaged rotors but it requires having good knowledge about heat treatment parameters (temperature and time) and their affects on fundamental properties of rotors. In this article, a suitable method is introduced in order to modify the increased stiffness in journal part of rotors due to martensite transformation, using heat treatment tempering process.

Oct 1, 2011

By David Runnels

The Mount Wright iron are mine and upgrading plant were brought on line in the fall of 1975. The mine is located near the Quebec - Labrador border some six hundred miles northeast of Montreal. This paper describes the crushing, grinding and concentrating facilities at Mount Wright, and some design: criteria used in equipment selection and flow sheet design. Also mentioned are some "asbuilt" modifications. A brief description of the over-all flowsheet is also included. Introduction IN SEPTEMBER 1970, the Quebec Cartier Mining Company started development of the Mount Wright iron ore mine. The estimated are reserve is in excess of 1,000,000 ,000 long tons of concentrates, with an average crude are grade of 31.5% Fe. The run-of-mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production r ate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material, of which 50% is waste.

Jan 1, 1977

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By J. A. Irvine

In 1972, a cooperative program to map and estimate the quantity of Tertiary coal resources in southern Saskatchewan was initiated by the federal and Saskatchewan governments. More than 700 exploratory boreholes were drilled over a two-year period, and data were obtained from other organization s on an additional 1500 boreholes in the area. Stratigraphic data and data on each coal seam penetrated in the boreholes, along with technical and location data for each borehole, were stored in a computer data base for convenience of retrieval, modification and manipulation. Programs and program packages were developed or adapted to: (1) select borehole information defined by variable retrieval parameters from the data base; (2) calculate derived information , such as overburden ratios. cumulative net coal thicknesses , mean weighted center of gravity of coal seams in each borehole, etc., from the selected data ; (3) produce posting maps of either selected data or calculated information in various combinations at variable scales on a plotter or CRT display; (4) produce contoured structure, isopach or ratio maps , and perspective diagrams as appropriate , utilizing plotter or CRT display; (5) calculate and categorize quantities of coal in place within user- defined "mineability-economic-reliability" limits. The emphasis in computer utilization was placed on geological credibility of the results and ease of operation by relatively untrained geological personnel, resulting in extensive use of interactive methods. The single most important benefit derived from using computer-assisted procedures is the ability to produce new maps and quantity estimates rapidly and inexpensively as a result of availability of new data or/and changes in external criteria which impose economic or mineability constraints.

Jan 1, 1978

By R. L. Bishops

This paper discusses some of the materials, processes and systems used in motor insulation. Among the materials mentioned are epoxies, polyesters, mica paper composites and wire enamels. Two processes developed to take advantage of the special characteristics of two of these materials are described, and how these materials are used in several new insulation systems now on the market is discussed. Finally, future trends in motor insulation are outlined.

Jan 1, 1969

By B. Schulz, T. Leißner, R. G. Merker

"Ores enriched in critical rare earth elements (CREE) keep on being of particular interest. The CREE are Nd, Eu, Tb, Dy, including Y. In conjunction with beneficiation tests on Y-mineral bearing flotation tailings of complicated mineralogy, the Mineral Liberation Analyses (MLA) was used to work out processing characteristics fraction-wise in terms of modal mineralogy, mineral recovery, locking and liberation, and particle size.Size fractions from mechanical sieving (“real fractions”) as well as fractions created virtually by using filters on the MLA-data of the unsieved head material (“virtual fractions”) were investigated comparatively thereby. The ""virtual-sizing-approach"" features a much simpler sample preparation procedure and considerably lower cost if a fraction-wise investigation of a head sample is needed. It can be conveniently applied to intimately locked ores needing a fine grinding to a particle size distribution (PSD) range below 25 microns for instance. However, its practical use is sometimes disputed in terms of the reliability of the results. Results are shown for the main Y-bearing mineral xenotime and selected main gangue minerals of a low grade REE-ore.The influence of sample representativeness, sample preparation and particle counting statistics turned out to be of crucial importance. Given that all preconditions for reliable results are met, locking characteristics, modal mineralogy, and even PSD trends can be read from virtual fractions.The authors encourage processing engineers to use the virtual approach. They propose practical measures to improve the reliability of the MLA results, identify and tackle conflicting results, and mitigate evaluation problems that may arise."

Jan 1, 2016

By B. S. Ignasiak, Dennis Carson

"Laboratory study of the behaviour• of binary coal blends shows that coke strength is more closely dependent on the distribution of ""reactive"" oxygen in the parent coals than on their proximate, elemental or petrographic compositions, and it also appears possible to qualitatively predict coke strength from information about reactive oxygen. Proceeding from this recognition, experiments were carried out to test the possibility of preparing metallurgical cokes from binary blends in which non-caking hvb coal was substantially freed of reactive oxygen by prior heat t1•eatment under controlled conditions. The results indicate that such blends can yield surprisingly strong cokes and that coke strength may be amenable to further improvements by modifying the size distribution of the pre-heated component and the rate at which it is charred."

Jan 1, 1976

By Jim Excell, Jim Rothwell, Mike Rylati

"LocationThe Ekati Diamond mine is located at Lac de Gras, Northwest Territories.Brief Description of OperationBHP Diamonds Inc. has developed Canada's first diamond mine in the Northwest Territories (NWT), Canada. BHP Diamonds Inc. is part of the BHP World Minerals Division ofBHP Minerals. The project is a joint venture between manager and operator BHP (51%) and the Blackwater Group (49%). The Blackwater Group comprises Dia Met Minerals Limited, Charles Fipke and Stewart Blusson.Production at the NWT diamonds project began in October with the mine officially opened October 14, 1998. The project is situated on an 853 000 acre claim block located in the Lac de Gras region of the NWT. It is about 300 km northeast of Yellowknife and 100 km south of the Arctic Circle. The seasonal winter ice road to the Echo Bay Lupin mine passes along the eastern margin of the project area. This allows road access each year from mid-January to mid-April. For the remainder of the year, the project is accessible only by air.HistoryIn 1980, Charles Fipke traced indicator minerals east from the Mackenzie River area. He discovered indicator minerals in the Lac de Gras area and staked mineral claims in 1989. A joint venture was formed between BHP and Dia Met in 1990, and in 1991, the first diamonds in the NWT were discovered at Point Lake by BHP and Dia Met. This initiated the largest staking rush in Canadian history. The joint venture launched an aggressive exploration program.Koala, Fox, and Leslie were identified in 1992 as potentially economic pipes.As soon as the project's potential was established, it was recognized that an enormous amount of work had to be completed in several areas before a mine could be developed, namely: technical evaluation of the resources; environmental and socio-economic evaluation to procure the necessary permits for the development; and engineering design to optimize mining and processing of the resource and to comply with specific environmental requirements."

Jan 1, 2000

By J. A. Russell

MR. M. W. Boom: I would like to congratulate Mr. Russell on his fine paper. One very good point which has always appealed to me is the smooth working of a steam hoist as compared with electrical. He does not mention the steam hoist at Springhill which has been working there for a good many years. MR. S. R. NEWTON: I have read with a great deal of interest the paper presented by Mr. Russell on the development of haulage engines in the mines of the Dominion Steel & Coal Corporation. He is to be congratulated on having produced a comprehensive article showing, step by step, the various improvements that have been made over the years in the design of such engines. I am quite in accord with Mr. Russell's statement that the positive tooth clutch can have too many teeth, and also that the method of driving a sliding clutch hub of any design should be by means of a hexagon or octagon on the shaft. Where the clutch hub does not of necessity slide on the shaft it can be pressed on and keyed to the shaft in the normal manner. With regard to the 'Cramp' internal-expanding jaw-type clutch, while it is true there are more moving parts than with the clutch consisting of a ring with internal cut teeth and a driver having a fewer number of teeth as .described by Mr. Russell; there are compensating advantages to the internal expanding jaw-type of clutch. The V shaped profile of the teeth permits of engagement of the clutch with very much less 'jockeying' of the drum. This is particularly the case in vertical-lift mine hoists, where it may be necessary to engage and disengage the clutching mechanism at frequent intervals.

Jan 1, 1944

By B. W. Snyder

INTRODUCTORY THE earliest known case of transmission of natural gas by pipe lines was early in the Christian era when the Chinese used bamboo pipes to transport natural gas from surface seepages to heat brine for the recovery of salt. Since that time many materials have been used as conduits-hollow wooden legs, wood stave pipe, day tile, cast iron, and, finally -since about 130 years ago - steel pipe. Even then, this new material came into use rather . slowly for, as recently as 80 years ago, wood pipe was still being used. However, as techniques were developed to take advantage of the properties of steel, this material gradually replaced all ethers for the transportation of gas for longer and longer distances at ever increasing pressures. In 1912, one of the longest pipe lines of its size at that time was built-this was a 16-inch line bringing gas from Bow Island to Calgary, a distance of 170 miles. We have been able to find records of only two ether such lines at that time-one a 185-mile 16-inch line from Vivian, Louisiana, to Little Rock, Arkansas, completed in the summer of 1911, the ether a 280-mile line from West Virginia to Toledo, Ohio. This last ? mentioned line was reported in a magazine article of September, 1912, but no indication was given of its size on completion date. It is apparent, therefore, that modern high pressure transmission of natural gas is a technique less than forty years old.

Jan 1, 1951

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

By L. Yuan, J. H. Rowland, R. A. Thomas, D. Bahrami, G. P. Cole

"The past several decades have seen a steady increase in the use of atmospheric monitoring systems (AMS) in underground mines as sensor technology has advanced and costs for this technology have decreased. The AMS is a reliable tool for early mine fire warning by detecting gaseous products of combustion in underground mines. During a mine fire emergency, mine decision makers rely heavily on the prompt and accurate knowledge of the ventilation and fire situation in the mine, such as fire location, fire size, and the spread of smoke to make effective and efficient decisions on firefighting strategies and miner evacuation. Meanwhile, a prediction of the potential for fire development at a later time, such as whether the currently designated mine escapeways will be contaminated by smoke and toxic gases with the progress of the fire, is critical for effective decision-making to save lives that are in danger. The AMS monitoring data, including carbon monoxide (CO) concentration, airflow rate, smoke, etc., can provide information as to whether the smoke has reached the locations where AMS sensors are installed and if a mine-wide smoke spread has occurred. The National Institute for Occupational Safety and Health (NIOSH) has undertaken a task to integrate real-time AMS monitoring data with the mine fire simulation program, MFIRE, to simulate and predict the spread of smoke and toxic gas in a ventilation network based on the real-time AMS data. This paper reports the developed real-time method for characterizing the size and location of an underground mine fire and for predicting the spread of contaminants throughout the mine ventilation network using sensor data from the AMS.INTRODUCTIONNIOSH conducts research to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in underground mines. The advancement of senor technology and the increasing demand for real-time mine parameters monitoring have led to extended applications of atmospheric monitoring systems (AMS) in underground mines worldwide. In the United States, AMS is primarily used for early mine fire warning by detecting carbon monoxide (CO) in fire hazard areas, such as belt entries. Mine fires can grow rapidly, and time is the critical element. Prompt detection, timely and accurate warnings to those miners potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground mine fire (Conti et al., 2005). The early detection of a mine fire could gain time for the first responders to put out the fire before it develops into a disaster. An AMS system with CO sensors has especially played an important role in the early detection of mine fires. The continuous monitoring of an underground mine atmosphere with an AMS could generate a large amount of data in a mine fire event. However, the current application of AMS is mainly limited to sending out an alarm when monitored CO concentration exceeds a certain level. An opportunity arises as to whether these data can be further used in fire emergency response. In order to make effective decisions on firefighting strategies, mine workers’ seeking refuges, evacuation and escape, and the timing on when to send rescuers, decision makers need accurate and timely knowledge of the ventilation and fire situation in the mine. Information about the fire intensity, where in the mine the smoke and toxic gases have spread, and whether designated mine escapeways have been compromised by smoke and toxic gases from the fire would greatly increase the effectiveness of these decisions. However, the monitored AMS data only provides atmospheric conditions in the vicinity of sensor locations. What is concluded from the monitored AMS data highly depends on the decision makers’ capability and experience. Predictive insight into fire growth and smoke transport would greatly help decision makers during a fire emergency."

Jan 1, 2019

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

By R. H. Waddington

Historical The limitations of reverberatory furnace operation have prompted many investigators to consider electric furnaces for melting electrolytically refined cathode copper. In the majority of cases where experimental work was performed, the furnace used was of the granular resistor, induction, or indirect-arc rocking type, and attempts to adapt the three-phase direct-arc furnace to copper melting appear to have been relatively few. In 1935, the International Nickel Company of Canada, Limited, carried to an advanced stage its experimental investigation of continuous melting of copper in the three-phase direct-arc furnace, and demonstrated that this process was technologically and economically practicable. Trial operations were conducted at the Huntington, W.Va. works of the Company, and were followed by the installation at Copper Cliff, Ontario, in 1936, of a full-scale unit for commercial operation. Two years later, a second unit was installed -which raised the electric melting capacity to a point permitting complete replacement of the coal-fired reverberatory furnace operation in the production of refined copper castings.

Jan 1, 1946

By L. Shasko, M. Hurlbert

As climate change is increasingly perceived as a problem, and fossil fuel based power production options are increasingly limited through regulatory restrictions and public distaste, future options become constricted. Reflexivity and social learning elicited through qualitative and mixed research methods offer important insight into what future power production pathways might be. Given factors of cost, baseload requirements, and energy density, options such as nuclear may be increasingly accepted. This paper explores this literature and possible methods of pursuing the reluctant acceptance of nuclear energy.

Jan 1, 2020

By R. Walker

This paper deals with the selection and design of a belt conveyor handling steam coal between a mine and a barge loading terminal, and extending for some 5 ¼ miles over some of the most rugged terrain in the state of West Virginia, U.S.A. After a thorough analysis by consulting engineers and the owner's engineers, a single-flight cablebelt conveyor was chosen as representing the alternative of greatest reliability and lowest over-all cost. The value analysis and design features of the system are covered in this paper along with an updated report on the performance of the system since its start-up in the spring of 1969.

Jan 1, 1971

By L. H. Cole

Introduction The increasing importance of the gypsum industry in Canada is evidenced by the fact that the production has increased from 473,129 tons valued at $809,632 in 1909 to 1,205,846 tons valued at $3,622,007 in 1928, an increase of over 155 percent in quantity, and of 347 percent in value, in the 20-year period. Although the export trade in crude gypsum still forms a large proportion of the industry, it is gratifying to see that the home consumption is steadily increasing, and while the percentage of the crude gypsum mined that is manufactured into the calcined products in the country is only 16.8 per cent, its value is practically 50 per cent of the total gypsum production of the whole country. It is to be hoped that each succeeding year will see an increase in the amount manufactured in Canada, and, with the steady growth of the country and a serious endeavour to capture a part at least of the world market in gypsum products, the outlook for the industry is decidedly promising. The value of gypsum as a commercial commodity has been known from the time of the early Egyptians; in fact its value for certain purposes has been known so long chat the date of the discovery of its peculiar properties is unrecorded.

Jan 1, 1930