Search Documents

By Törbjorn Naarttijärvi, Bengt Ludvig, Agne Rustan

"Falling rock is one of the major causes of serious injuries and deaths in Swedish mines. The research at the Division of Mining and Underground Construction was therefore directed toward controlled blasting in hard intense jointed rock.The project was started with an extensive literature review. Model tests with a new equivalent model material have been initiated to find ways of improving blasting techniques. The result showed that long cracks arise at the perimeter holes when there is a long time delay between adjacent holes. This led to the theoretical development of a new initiation method with ultra short delays (1,5 ms) f or controlled blasting, called ""Cutblasting"".Full-scale tests have been done at LKAB in Malmberget in hard intense jointed magnetite ore. Four different types of perimeter charges have been tested, namely: tube charges, ANFO mixed with plastic beads, detonating cord and linear shaped charges. Three types of initiation of the perimeter holes have been used, conventional (half-second delay detonators), instantaneous and ultra short ""cutblasting initiation"" (1,5 ms delay). The change in rock strength before and after blasting has been studied with bore hole periscope, vibration measurement and ocular observation of the rock surfaces.Thefull-scale tests showed that ""cutblasting"" with detonating cord in the perimeter holes gave the smallest damage to the surrounding rock. A combination of cutblasting initiation and tube charges are anticipated to give an even better result. A new method of controlled blasting using linear-shaped charges has also been tested, however, this charge type needs further development.The full- scale test also showed that the damage which can be seen on the rock surf ace is about the same for different controlled blasting methods but the not-visual-damage zone varies as much as from 0,1 to 0,7 m.A new classification system for controlled blasting regarding the damage to the surrounding rock has been devised."

Jan 1, 1985

By W. R. Middagh, R. M. Garvey

"Phosphate rock is shipped by boat from Florida to Vancouver, B.C., where it is unloaded and stored in a 50,000-ton silo. It is shipped from Vancouver in 100-ton hopper cars in 80-car trains to Fort Saskatchewan. Both the ship and the hopper cars are on a back-haul with potash. The rock cars are unloaded at Fort Saskatchewan at a rate of approximately 4 cars per hour. The rock is stored in three concrete silos, 40 ft in diameter by 110 ft high, which hold 18,000 tons of recoverable rock with 2,000 tons dead space. The rock is reclaimed from the silos by gravity and fed to the phosphoric acid plant by remotely operated conveying equipment.Problems encountered in the operation include scheduling the rock shipments, contamination of the rock with potash, and handling the 80-car trains both in Vancouver and Fort Saskatchewan."

Jan 1, 1968

By D. K. Sarkar, Jiawei Xiong

"Self-assembled monolayers (SAM) on the aluminum substrates are used as the adhesion promoter between two aluminum substrates when bonded with the adhesive in adhesive bonding technology. Traditional surface analysis tools are not capable of identifying the presence of SAM on a surface; therefore, EIS has been used to determine their presence on the aluminum substrates. In this study SAMs have been deposited on aluminum using the monomer of (3-Glycidyloxypropyl)trimethoxysilane (GPTS) organosilane. AA6061 aluminum alloys substrates were chemically cleaned with NaOH and HNO3 to remove the native oxides, followed by immersion in silane solutions. In a second method, SAMs were prepared by applying a spin coating of silane solution to the samples. The prepared SAM coated aluminum samples were analysed by EIS in the three electrode corrosion cell using a diluted alkaline solution. The impedance of the SAM coated aluminum is found be higher than the as-received aluminum. It has been also observed that the open circuit potential (OCP) of the SAM coated aluminum is higher than the as-received aluminum. Both elevated values of the impedance and OCP confirm the presence of SAM on aluminum.INTRODUCTIONSelf-assembly (Schreiber, 2000) is defined as the spontaneous formation of complex hierarchical structures from pre-designed building blocks, typically involving multiple energy scales and multiple degrees of freedom. Generally speaking, SAMs are created by the chemisorption of ""head groups"" onto a substrate from either the vapor or liquid phase followed by a slow organization of ""tail groups"" of a molecule. Typically, head groups are connected to a molecular chain in which the terminal end can be functionalized with groups such as –OH, –NH2, –COOH, or –SH to vary the wetting and interfacial properties (Chauhan et al., 2007; Ulman, 1996; Vashist, Lam, Hrapovic, Male, & Luong, 2014). Though there exist several methods to prepare SAM (Chauhan et al., 2007; Chen, Yang, & Zhang, 2014; Cho, Park, Jon, & Choi, 2007; Igor Luzinov, 2000; Reis, de Melo, & Costa, 2006; Song, Zhai, Wang, & Jiang, 2006; Sugimura, Hozumi, Kameyama, & Takai, 2002; Vashist et al., 2014), the two methods vapor phase (Song et al., 2006; Sugimura et al., 2002) and solution(Chen et al., 2014; Igor Luzinov, 2000) are commonly used. Recently, many articles have been published on the fabrication of superhydrophobic surfaces with SAM technology (Cho et al., 2007; Pan, Shen, Shang, & Xing, 2012; Siddaramanna, Saleema, & Sarkar, 2014; Song et al., 2006). Brassard, Sarkar, and Perron (2011) successfully obtained a superhydrophobic film by applying fluoroalkylsilane via self-assembly on monodispersive silica. SAMs are also reported as good candidates for anti-corrosion and adhesion promotion (Chen et al., 2014; Saleema, Sarkar, Paynter, Gallant, & Eskandarian, 2012). However, papers on the characterization of SAM properties are rarely seen. The most commonly used substrate for SAM is silicon and the method implemented is scanning probe microscopy (SPM) such as atomic force microscope (AFM) (Igor Luzinov, 2000; Moores, 2011; Zhang, 2003, 2005). Igor Luzinov (2000) analyzed the epoxysilane SAMs’ surface morphology and microstructure properties using scanning probe microscopy (SPM) and ellipsometry on single-crystal silicon wafers. SAMs have been used to improve the adhesion bonding of aluminum or plastics but no characteristic data have been presented yet (Saleema et al., 2012; Telegdi, 2007; Wang, Xu, Luo, Wang, & Wang, 2009). Recently, Reis et al.(Reis et al., 2006) have studied SAM of alkane diphosphonate (Gardobond X4661) on Al 5052 alloy samples by EIS in a naturally aerated sodium sulfate solution."

Jan 1, 2016

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

By Ngonidzashe Chimwani, David Glasser, Diane Hildebrandt

"Milling circuits play an important role in achieving the desired product; tonnage, size distribution and properties, since they are directly linked to the comminution energy consumption for the whole process. A grinding model with a mathematical simulation was developed for an open milling circuit with a scalped feed from a hydro-cyclone. The circuit was optimized by determining the optimal conditions in terms of energy consumption which would produce a floatable product having a desired size range (i.e. -75 +9 µm) for a platinum-bearing ore. The simulation results showed an operating region comprising the best combination of the ball filling and mill speed to achieve the highest production of a floatable size class, with the minimum energy consumption.INTRODUCTIONBall milling is usually conducted in closed circuits in order to achieve a desired product size without material overgrinding. The technological importance of optimising milling circuits cannot be overemphasised (Toneva and Peukert, 2007). Previous work has brought significant insights into the benefits of modelling milling circuits (Austin et al., 1984; King, 2012; Toneva and Peukert, 2007). However, the ability to model these circuits is dependent on the performance of the classifiers and the fidelity of the grinding mill model used compared to the actual circuit (Toneva and Peukert, 2007). Austin et al. (1984) identified five types of milling circuits as shown in Figure 1 namely; the grinding circuits employing mill in an open circuit, normal closed circuit, reverse closed circuit, open circuit with scalped feed, and, the combined closed circuit. Depending on the presence of the first classifier, the second, or both as well as their corresponding loops (streams), the combined circuit (e) can reduce to; an open (d), a normal closed (b), an open circuit with scalped feed (c) or a reverse closed circuit (a). In the case of an open circuit, the mill is operated without being directly influenced by a classifier. The normal closed circuit does not have the first classifier and therefore the make-up feed is the actual feed stream. Conversely, the reverse closed circuit keeps only the first classifier. The open circuited with scalped feed has only the first classifier but does not have the second one. The overflow stream from the classifier is mixed with the mill product to form the final product for the downstream process."

Jan 1, 2016

By Sylvain Létourneau

Help organizations maximize the benefits of the data that they collect ? perform scientific research in: machine learning, data mining, statistics, artificial intelligence, soft computing, information retrieval, information systems, and natural language processing ? preferred application areas: Equipment Health Management, Bioinformatics, Health, Web Mining ? today?s talk limited to Equipment Health Management While the aircraft is still in the air, IDS: ? clusters relevant WRN, FLR, and snag (pilot) messages ? identifies probable causes based on TSM and provide links to corresponding TSM pages ? assesses MEL conditions (GO, NOGO, GOIF, ?) ? displays relevant maintenance history, suggests fixes based on similar cases ? Commercialization with MxI Technologies Ltd and Air Canada in 2000

May 1, 2008

By H. C. Counsell, R. Webber

"The mill at Denison Mines' Elliot Lake Operations started up in 1957, with a capacity of 6,000 tons per day. Over the years various plant modifications expanded th.is to 7 500 tons per day. In 1976, management decided to carry out a major expansion of the milling capacity, and during 1980 the grinding capacity was increased to 15,000 tons per day.The original comminution system consisted of a conventional crushing plant feeding minus S/s-inch material to rod and pebble mills, in closed circuit with mechanical classifiers. The key decision that had to be made was whether the expansion should include conventional or autogenous grinding flow sheets.During 1977, extensive pilot plant studies at Lakefield Research showed that two-stage semi-autogenous grinding, with some steel media in the primary mill and with pebble media in the second stage, produced stable grinding conditions. This type of circuit was selected by Denison for the expansion, and went into production in 1980. Primary millThe flow sheet of the semi-autogenous grinding circuit is shown in Figure 1. The primary grinding mill is a Koppers 28 foot by 10 foot mill, driven by a 4,000 h.p. synchronous motor. It is fed with a minus 8-inch run-of-mine ore, and 4-inch grinding balls are added as supplementary grinding media. There are two Koppers 15.5 foot by 22 foot secondary pebble mills, driven with 1500 h.p. synchronous motors. Each grinding stage operates in closed circuit with cyclones, and the primary cyclone overflow is the feed to the secondary mills. The circulating load in the primary stage can be controlled by adjusting the cyclone apexes."

Jan 1, 1984

By Wayne N. McKee, Scott A. Lewis

"Introduction to the Syncrude OperationSyncrude Canada Ltd., located 42 km north of the city of Fort McMurray, Alberta, (Fig. I) is an integrated operation that has produced synthetic crude oil from the Athabasca oil sand deposit since 1978.The operation, consisting of a surface mine, an extraction plant, a bitumen upgrader, and a utilities plant, is currently capable of producing over 60 million barrels of crude oil per year. Production is expected to increase to 70 million barrels of crude oil per year over the next five-year period with no major changes to equipment or process planned.The Syncrude surface mine, producing a total of 675 000 tonnes of ore and waste per day, rates as one of the largest mines in the world. A strip mining method is utilized, with two or three operating benches necessary to excavate a total depth varying between 60 m and 70 m. The 20 m to 30 m of overburden is removed by electric and hydraulic shovels and 200-ton haul trucks, and dumped in the mined-out pit for final storage. The overburden operation creates a flat bench near the top of the ore zone on which the four 60 m3 draglines operate. The draglines excavate interbanded ore and waste in the highwall, with ore placed on the operating bench in windrows, and waste returned to the mined-out pit. The windrowed ore is reclaimed by four bucketwheel reclaimers, and discharged onto a conveyor system for transfer to the extraction plant."

Jan 1, 1993

By R R. Wainwright

Friction-type hoists have been in operation at Geco Mines Limited since Septtember, 1957. At the end of the year 1963, the skip hoist had handled nearly ~ million tons of ore and waste. In March, 1962, with the deepening of the shaft, the hoisting de11th was increased from 1,450 to 2,450 feet. Operating experience with the hoists, hoist and balance ropes, rope treads and other related equipment is presented. The paper is intended to supplement an earlier one -"Heavy-Duty Friction Hoisting at Geco Mines," by W. M. Harvey (C.I.M. Transactions, Volume LXIII, 1960, pp. 193 -197). General G ECO Mine Limited is located at Manitouwadge, Ontario, approximately 160 miles east of Port Arthur and 190 mile northwest of Sault Ste. Marie. The Company was formed to exploit a copper-zinc-silver orebody, with current ore reserve (1963) of approximately 21 million tons. The production plant was designed to mine and treat 1.25 million tons per annum. The production and service hoists are mounted at-the top of a reinforced concrete tower above the shaft.

Jan 1, 1965

By G. Bonnell, W. Lidkea, M. C. Bétournay, E. Edwardson

"Hydrogen fuel cells are a known technology, having been applied to stationary (e.g equipment, buildings, and power plants) and vehicle applications (e.g transit buses and space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and greenhouse gas emissions.To date, however, fuel cells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuel cells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuel cell type of choice for the industry, the proton exchange membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk.A small fuel cell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, Inco, the Ontario Ministry of Labour, Sandia National laboratories, and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter, as well as from shock and vibration provided to the unit in underground conditions at Inco’s 175 Orebody minesite and Stobie mine. The test results provided will show that the unit was not affected by the underground conditions; physically and electrically, the unit performed without any reduction in operation or adverse effects imposed."

Jan 1, 2005

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

By A. Siegmund, F. Mucciardi, Z. Yuan, B. Bulnes

With conventional heat pipe science as the starting point, a new heat transfer technology --- termed Thermopump technology, has been developed at McGill University and is now being tested at a number of industrial operations. This technology is of particular importance for transferring energy in high temperature / high heat flux environments where solutions based on current techniques are not available. One important application for this technology is in the metals recycling area wherein this technology has been used to make a waterless, non-consumable, high efficiency Thermopump oxygen lance. The viability and efficiency of this oxygen lance have been demonstrated by preliminary plant trials in a reverb furnace for the recycling of lead-acid batteries at the RSR Corporation. Full-scale commercial trials of the Thermopump (TP) oxygen lance have been carried out at the RSR Corporation. The results from these tests will be presented. In addition, some applications of the Thermopump technology for other metal recycling processes will also be discussed in this paper.

Jan 1, 2004

By D. W. Euler, B. J. Clauzier

"Implementation of an effective energy management system will reduce energy costs without impacting negatively on production.The energy management system must be designed to complement the operation and be integrated with the organization. It must be reliable and easy to use but most important, it must have an accurate and timely feedback reporting system to allow the operation to take appropriate action.Falconbridge Limited was one of the first three companies to be awarded the energy monitoring demonstration program in May 1987. The program is sponsored jointly by the Ontario Ministry of Energy and Ontario Hydro.This paper describes the approach taken by Falconbridge Limited to implement the Onaping Area Energy Management System.IntroductionThe objective of the project was to implement an effective energy management system, capable of reducing energy costs without impacting negatively on production.Energy management systems must be designed to complement the operation and to be integrated with the organization. The system must be reliable and easy to use, but most importantly, it must have an accurate and timely feedback reporting system to allow the operation to take appropriate action."

Jan 1, 1990

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By F G. Cooke

"This paper describes a medium-sized copper mine's results in making innovations and changing operational practices to combat increasing expenditures due to higher labour and supply costs, extended workings, scarcity of experienced manpower and problems created by deteriorating ground conditions.OPEMISKA COPPER MINES (QUEBEC) LIMITED is located at Chapais in the Chibougamau area, in central eastern Quebec, approximately 300 miles north of Montreal and 150 miles north west of Lake St. John. The latter area, developed by lumbering and farming, has supplied the majority of the employees, who, with training and experience and a desire to work and improve themselves, have become the backbone of the Company's 600 personnel.Opemiska began production in 1954 at a rate of 400 tons per day, using diesel power and road transportation. The rate was progressively increased and, by 1959, with hydro-electric power and rail transportation, the mine had reached its present production rate of 2,000 tons per day. It has produced concentrates containing over 430 million lbs of copper."

Jan 1, 1968

By Hossein Aminian, Daniel Hodouin, Claude Bazin, Claude Jacob

"Solvent extraction followed by electrowinning (SXEW) is an economical option for the processing of low grade and oxidized copper ore. Phenomenological models were developed to simulate the copper solvent extraction and the electrowinning processes. The two models were linked together to make a SX/EW simulator. The simulator is used to predict the operation of the mines Gaspe pilot plant put in operation in 1996. Results confirm the potential of the simulation that would subsequently be used for student training, process optimization and to assess the performances of control strategies.INTRODUCTIONSolvent extraction followed by electrowinning (SXEW) has become in the last two decades a key process for the recovery of copper from solution obtained by leaching low grade copper ore. Several operations have been commissioned in North and South Americas in the last decade (Arbiter, 1994). In Canada, Gibraltar Mine (Scott, 1991) operates a SX plant followed by electrowinning (EW) to produce copper cathode from leached low-grade ore dumps. From 1996 to 1997 Mines Gaspe operated a pilot plant to test the economical feasibility of leaching an oxidized copper ore, followed by solvent extraction and electrowinning of copper. Despite copper SX/EW processes have the reputation of being low cost operations, plant engineers should always look at way to make the plant more efficient. Process models provide an economic platform to learn, control and ultimately optimize the operation of a plant.Several models have been independently proposed to simulate the SX process (Cadman and Hsu, 1970; Medina Gomez, 1980; Wilkinson and Ingham, 1983; Garcia et al., 1988; Aminian et al., 1997) and the EW process (Bryson, 1981; Barton and Scott, 1992; Barton and Scott, 1993). However few papers, if any, deal with the integration of the two process models into a single simulator of a SX-EW plant. This paper describes the development of an integrated simulator for the SX-EW process and shows some steady-state simulation runs of an actual SX-EW pilot plant. The paper consists of four sections. The first section shows the general layout and principles of operation of a SX-EW plant.The second section describes the SX model while the third section deals with the process model used for the copper electrowinning process. The last section shows how the two process models are linked to simulate the operation of the Gaspe pilot plant."

Jan 1, 1999

By Tony Lipiec, Ian Orford

"A key part of plant design is the selection of the design tonnage which is the hourly tonnage target that the equipment selection is based on. Its selection is critical for ensuring that the nominal tonnage which is critical to the financial performance of the project will be met. With deposits being developed at lower grades, higher tonnages and a higher degree of hardness variability, it is essential to ensure that the design process selects the comminution equipment which will be able to deal with the impact of this ore quality variation.Ore hardness and its variance are key factors to be taken into consideration for the selection of the design tonnage. It is well accepted that for the nominal or name plate tonnage to be consistently achieved, it is necessary to base the design tonnage on a hardness value greater than the average ore hardness of the deposit to be mined. The question is how much greater should this design value be to ensure that the nominal tonnage is met to the satisfaction of the project financial model. Standard industry practice is to set the design tonnage by:1. Select an ore hardness percentile that is greater than the average ore hardness to be the basis of the nominal tonnage. Typically either the 75th or 80th percentile value from the data set will be selected.2. Selection of a design factor to multiply by for determining the design tonnage, i.e. the design tonnage = tonnage (based on the average ore hardness) multiplied by design factor.This paper discusses the selection of the design ore hardness through the use of modelling or the use of a design factor. It further shows the impact of ore hardness variance on the capacity of the process and its ability to meet the nominal tonnage. Insight is provided as to what ore hardness percentile value should be selected balancing the shortfalls of tonnage for ores harder than the design value versus the above target production achieved for ores softer than the design ore hardness."

Jan 1, 2016

By C. R. Edwards

"Equity Silver Mines Limited, Canada's largest silver mine, has designed, built and operated a leach plant to reduce the levels of antimony and arsenic in its silver-gold-copper flotation concentrate. The orebody contained deleterious antimony and arsenic minerals in such proportions that the economic long-term sales contracts necessary to obtain project financing could not be procured. Construction of the leach plant therefore allowed development of the mine to proceed. Although the plant took some time to reach design throughput and product specifications, due to the complex and unique nature of the operation, these goals were successfully met and surpassed. This paper describes the physical plant and/or process technology modifications made to mold the main processes-concentrate leaching and filtering, autoclaving and filtration of by-products, and crystallization of salt cake-into an effective, economic operation.IntroductionEquity Silver Mines Limited, a member of the Placer Development Group, owns and operates an open-pit silver mine and related facilities located 37 kilometres southeast of Houston in north-central British Columbia. The mine occupies a 44 I-hectare (1089 acre) site at an elevation of 1300 metres (4265 feet) on the Nechako Plateau. Producing a copper concentrate containing high values of silver and gold, it is the largest silver mine in Canada and one of the largest in the western world. Equity stresses open communications, positive motivation, and production with safety, and achieved the best mine safety record in western Canada in 1984."

Jan 1, 1985

By Eugene Barsky

"At present, theoretical concepts of gravitational separation processes are mainly limited by the study of the interaction between a flow and a solitary particle. Then the main conclusions of this analysis are applied to a mass process. However, this analysis is absolutely insufficient, because some elementary phenomena such as the ingress of coarse particles into the fine product output and vice versa cannot be interpreted from its standpoint. It is also impossible to predict the results of the classification of a material with a specific granulometric composition on a specific apparatus on its basis.In the present paper, an extended model of the process is suggested. The model is based on the behavior of all the particles of a specific narrow size class, and not on that of an individual particle. Similarity criteria of the process, which were empirically derived previously, are obtained from the analysis of this model.INTRODUCTIONIn case of gravitational separation, a part of solid phase moves, as a rule, vertically upwards with the flow, while another part settles against the flow. This flow is extremely complicated and chaotic due to various random factors. Among these factors are mass interactions of particles with each other and with the apparatus walls, non-uniform character of concentration and velocity fields, turbulent vortices and local fluctuations, real particles shape difference from spherical one, etc.Particles rotation results in a transverse force (Magnus' effect). At the motion of a non-rotating particle in a non-uniform velocity field, a transverse force also arises (Saffman's effect).A great number of publications have been devoted to the account for all these factors in two-phase flows in recent decades. Very complicated models have been developed, but the problem has not been completely solved as yet [1, 3].At the same time, simplified models of the behavior of a solitary particle in a flow are being developed. Despite their schematic nature, such models often prove to be useful for establishing general laws of the process and its similarity criteria [1]."

Jan 1, 2016

By R. W. Boyle

"PREFACEThis paper comprises two parts. The first part discusses lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos. The second part continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, geothermometric, geobarometric, thermolumin escent, pedochemical, hydrochemical, atmochemical and biogeochemical methods. A selected bibliography follows the second part of the paper.ABSTRACTAreal (two-dimensional) geochemical surveys, based mainly on secondary dispersion halos and trains in media such as surface waters, soils and drainage sediments, have proven particularly successful in recent years and have greatly assisted in the discovery of a large number of varied mineral deposits. Three-dimensional surveys based on primary halos and leakage halos have received relatively little attention by research organizations and the mineral industry. Such surveys offer many novel approaches for discovering blind mineral deposits deeply buried below overburden or within their host bedrocks. This paper reviews detailed methods for the discovery of blind mineral deposits based on sampling rocks (lithochemical methods), soils and other types of overburden (pedochemical methods), waters (hydrochemical methods), gases (atmochemical methods) and biological materials (biogeochemical methods) . All are applicable to the discovery of blind deposits; the efficacy of each or in combination depends essentially on the type of mineralization, the extent of the development of the primary and secondary dispersion halos, and the finances available for sampling techniques employing overburden drilling, bedrock drilling, and sophisticated water, gas and vegetation collection."

Jan 1, 1982