Search Documents

By J. Kolacz

"A new sensor based sorting system has been developed, providing a possibility for laboratory scale testing and further scale-up of the separation results to the industrial operation. The new system contains different sensors as: X-ray detectors, visible light cameras, NIR cameras, ultraviolet cameras and magnetic sensors, in the same sorting unit. The sorting unit allows advanced calibration options and fine-tuning of the installed sensors to achieve the best separation effect under controlled conditions. Finally, the processed material can be analysed and separated by the rejection mechanism, similarly to the industrial scale operation. At the same time, the process is carried out with limited amount of material allowing detailed statistical calculations for processed particles and all sensor types. The optimal settings and sensor types are specified for the industrial application.The paper describes the scale up of the results achieved for iron ore and coal, where the test work was first carried out using the new laboratory sorting system and where the industrial scale sorting system has been built, in the final stage. The industrial scale sorting results showed a very good correlation between the laboratory and full scale operation. Thanks to the detailed study carried out in the laboratory equipment, the settings of the sensors in the full scale operation provided much better separation efficiency. It was especially important to provide proper setting for the X-ray sensor data calculations, which can be very critical for achieving the best results. During the industrial scale sorting of coal, the input material had 40-55% rock particles as the direct source of ash in the coal stream. The optimal laboratory unit settings and transferring these settings to the industrial sorter, provided 98.8% efficiency for removing rock particles with only few % losses of coal."

Jan 1, 2016

By H. Al-Kazzaz

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded using 1.6 mm EZ33A-T5 filler wire and a continuous wave Nd:YAG system at a power of 4 kW, surface defocusing and various welding speeds, Compared with the base metal, the fusion zone showed significant grain refinement due to high cooling rate, No grain coarsening was observed in the heat affected zone (HAZ). The porosity area percentage and total solidification crack length in the fusion zone (FZ) were reduced as the welding speed increased from 4 to 7 m/min, Fusion zone area, total penetration depth, and weld width decreased with increased welding speed, The hardness in the FZ was similar to or higher than the base metal after a natural aging of about one year, but there was a drop in the hardness of the HAZ, The HAZ width decreased with increasing the welding speed, Tensile test showed that a joint efficiency of approximately 75 ? 90 % was obtained.

Jan 1, 2005

By G. C. Lipsyy

ALL mineral production? of Can11.da is transported in a mine car at some stage during its extraction. There are as many types and varieties of mine cars as there are of mines. Many of the cars in use were developed in the blacksmith shop. Others were designed by engineers and improved by the mine foremen and the mechanics. Every mine car has the ideas of miner, blacksmith, mechanic, and engineer incorporated in it. Many of these ideas are not generally known. This paper was written to make at least some of this information available to the mining industry. In drawings, tables, and notes, it gives all the important details pertaining to the cars. It .does not recommend any particular type of car for any particular piece of work, nor does it present drawings from which a car can be built. It gives the engineer or master mechanic information on many cars which he can apply to his own particular problems. It is hoped that this information will be of use to mine operators. If a few new ideas are conceived as a result of the paper, the author will feel that the effort of compiling it has been worth while. In order to obtain the data for the preparation of the paper, a questionnaire, copy of which is here reproduced, was sent to all the operating mining companies in Canada. An accompanying letter briefly explained the purpose of the paper and asked for co-operation in furnishing as complete information as possible.

Jan 1, 1945

By H. Hejny

Economy needs mineral raw materials in almost each sector of modern life. They can only be provided by mining activities. An increasing share of the total mining production will be by underground mining. The mineral deposits will be found at gradually greater depths, including all problems associated with them. It involves an increase in overburden pressure with subsequent rock stability problems and risks of structural collapse. There is a need for new and safe technologies for almost all parts of a modern mine. The mining industry faces a number of challenges which require technical solutions that encompass the entire network and include the economic, social and environmental issues. The industry needs a new image based on pioneering solutions and a modern structure that can exploit minerals at greater depths and promote both high productivity and safe working conditions. Funding has been secured from the European Commission for the I²Mine project. Work started in November, 2011. This initiative is designed to focus on the technological challenges that the mining industry is currently facing including the exploitation of ever deeper deposits and the aspiration for an invisible, safe, zero impact mine. The project comprises a consortium of 27 organisations from 10 European countries. I²Mine marks the start of a series of development activities aimed at realising the concept of an invisible, zero impact, deep mine. The extractive sector, still seen as being old fashioned and environmentally unfriendly, will show that mineral extraction and processing can be done in a highly innovative and sustainable manner with low impact underground and zero impact above ground. The concept of I²Mine is to develop innovative methods, technologies, machines and equipment necessary for the efficient exploitation of minerals and disposal of waste, all of which will be carried out underground. This will dramatically reduce the volume of surface transportation of both minerals and waste, minimising above ground installations and reducing the environmental impact. New eco-efficient technologies will be applied in order to make the entire mining process more efficient and environmentally sound. The concept is for an integrated mine, with the majority of the installations underground, and only the final product will be transported above ground to be shipped to the customer. Production waste will be treated and stored underground and gaseous emissions will be managed underground as far as practical. I²Mine will also focus on ideas and concepts that increase energy efficiency and decrease waste. The core of the project will be to develop breakthrough technologies for autonomous, highly selective, continuous mineral extraction processes and machinery based on new sensor technologies, face front separation as well as innovative concepts for mass flow management and transportation integrating state of the art technologies. The concept of an invisible, zero impact mine requires a refined process underground that selectively extracts the mineral thereby reducing waste. For this reason, improved extraction machines and near to face processing methods, including backfill procedures, need to be developed. These developments include rock mechanics and ground control solutions, incorporating health, safety and environmental issues.

Aug 1, 2013

By P. R. Geoffroy

Extensive and Intensive Prospecting As often pointed out, the search for new ore deposits may be carried on along two widely divergent lines. It may be either extensive or intensive. By extensive prospecting we mean a search for mineralized outcrops conducted over large and more or less virgin tracts of land, followed by a test of the practical value of any discovery made, the test being limited to the immediate vicinity of the outcrop. Extensive prospecting, was, in fact, the only policy known to the early prospectors. of the American continent and is still the rule in the remote sections of the Canadian Shield and in the African wilderness. It can be further characterized by the lack of emphasis placed on geological and other technical means as an aid to the search for ore. However, very little virgin ground is left, nowadays, for a man or a company to test their luck, and whatever is left is so remote from the necessary means of development that any new discovery will require considerable delay and expenditures to be amenable to profitable mining. On the other band, a great many of the favourable and still unexplored areas (and this is particularly true in Canada) are overburdened to such an extent that outcrops of bed-rock are extremely scarce and extensive prospecting is nearly impossible. Intensive prospecting, to the contrary, must be understood as a detailed search for ore carried on over limited areas in districts already known to be mineralized and covering regional structures whose relation to mineral deposits bas been estahlis.hed with a fair degree ot certainty. The search for deep-seated deposits in the vicinity of successful mines is a perfect example of intensive prospecting. As a matter of fact, the majority of the geologists employed by the mining industry are engaged in some kind of intensive prospecting.

Jan 1, 1950

By John Lund

INTRODUCTION GOLD-BEARING placers of Alaska and the Yukon Territories are buried under a layer of permanently frozen alluvial overburden, or 'muck', which varies in depth from twenty to one hundred feet. The placers, and the decomposed bedrock layers upon which they are deposited, are also permanently frozen. During the summer, surface muck which is exposed to the sun will thaw, but only to a depth of a few feet. To reach a valuable deposit, the frozen overburden must be either penetrated with shafts, or stripped from the deposit entirely. In either case, before the placer can be mined, it must be thawed. At modern dredging operations, the frozen muck is stripped from the placer by powerful jets of water from hydraulic giants. The placer, and several feet of decomposed bed-rock, are then thawed by forcing water through narrow pipes which have been driven into the deposit. Other methods of thawing frozen placers were used extensively during the early years of the Klondike 'gold rush', but experimentation later proved that creek water at its natural summer temperature was a more effective and economical thawing medium than any other which had been used. EVOLUTION OF COLD WATER THAWING Early prospectors of the far north reached placers by digging shafts through the frozen muck. They then thawed the placer sand and gravel by building wood fires at the bottom of the shafts.

Jan 1, 1951

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

By G. Anger, J. Enser, H. Antrekowitsch, S. Koch

Homogeneous chemical composition and microstructure are always necessary, but not always attained in practice. As-cast aluminium alloys tend to have a segregation microstructure. Features of the cast structure, which affect subsequent processing or properties, can be altered by the homogenization. The main task of the Department of Nonferrous Metallurgy was to investigate the effect of homogenization treatment on precipitation hardening of aluminium alloys 6061 and 6082. The effect of the solution heat treatment (SHT) temperature on the mechanical properties was also analyzed. The homogenized and non-homogenized rolling slabs were produced according to the usual conditions and methods. The metallographic investigations were carried out on the as-cast samples, after homogenization, after the hot and the cold rolling mill, and after natural and artificial ageing. Then, Brinell hardness measurements and tensile tests were conducted on both alloys in order to examine the influence of the homogenization.

Jan 1, 2006

By M. Holmes, R. Molnar, E. Norton, K. Baxter, J. Riordan

The Boleo Copper-Cobalt-Zinc-Manganese Project of Baja Mining Corp. is situated adjacent to Santa Rosalia on the Baja Peninsula of Mexico. The El Boleo ore is a mixed oxide-sulfide deposit with major values in copper, cobalt, zinc and manganese. The metallurgical process designed to treat the El Boleo orebody involves a sulfuric acid leach in seawater using oxidative and then reductive leaching to maximize metal extraction. The leach solution is separated from the barren solids via counter current washing through a series of high rate thickeners. Copper is recovered using conventional SX-EW processing as cathode. Zinc and cobalt are extracted from the copper SX raffinate after iron and aluminum precipitation. The CSIRO DSX solvent system (Versatic® 10 and LIX® 63 mixture) are used in this extraction. Manganese remains in the DSX raffinate and is recovered by soda ash addition as a high quality manganese carbonate precipitate. Zinc and cobalt are acid stripped from the loaded DSX solvent. Zinc is then re-extracted away from cobalt using Cyanex® 272 extractant and stripped into a highly concentrated strip liquor (+100 g/L Zn) and directed to either a spray dryer or a granulator for production of zinc sulfate monohydrate. The zinc solvent extraction raffinate, containing cobalt, advances to another SX circuit using Cyanex® 272, for the recovery of cobalt as cobalt cathode. In this paper, the detailed results from bench and integrated pilot plant testing for zinc recovery from the El Boleo ore will be described. The results of this testing are currently being used to engineer the commercial plant at El Boleo.

Jan 1, 2008

By M. Sagedahl

The off gas from a smelter is cooled and dust removed in an electrostatic precipitator before approximately 95% of the sulphur dioxide (S02) is converted to sulfuric acid. However, the tail gas may need to be polished to remove the rest S02 to meet demands. A flue gas desulphurization (FGD) system, as usually applied to S02 removal on coal and oil fired Power Station, is suitable for polishing tail gases from copper smelters. The ALSTOM Seawater FGD process makes use of the alkalinity in the seawater to absorb and neutralize S02. Before being returned to the sea, the seawater is treated to comply with environmental regulations. As the ALSTOM Seawater FGD process uses no reagent and produces no byproduct, it is extremely cost-effective for coastal installations. The first SWFGD plant started operation in 1968. Over 60 of these units have been installed worldwide. The ALSTOM Seawater FGD process removes S02 from flue gas flows corresponding to a total of 70,000,000 Nm3 /h. Suitable for thermal power stations, smelters and oil refineries, ALSTOM Seawater FGD plants efficiently treats flue gases in the range of 300,000 Nm3/h to 2, 700,000 Nm3 /h per FGD plant, containing 20 - 6,500 ppm of S02.

Jan 1, 2007

By X. Xu, J. K. -W. Wong, J. -Y. Delenne, K. Soga

Hydraulic fracturing (HF) is a mulit-scale and multi-physics process which makes numerical modelling challenging. Conventional numerical models focus on multi-physics nature of HF but the multiscale nature is compromised by idealization of reservoir to be continuous, homogeneous and isotropic. However, natural fractures take a significant role in the success of HF for exploration of unconventional resources like Shale gas. Advancement in microseismic monitoring provides useful data for simulation in a much greater details. There is an urgent need to develop a suitable numerical tool for multi-scale threedimensional simulation to better understand the roles of discontinuities and heterogeneity in reservoir and its interaction with HF, especially to address the environmental concerns such as induced seismicity. In this paper, a simple discontinuum numerical method – Lattice Element Method (LEM) is proposed to model HF in a large scale three-dimensional model. A reservoir is modelled as a lattice network composed of 1D Hookean’s spring. Fracturing is modelled simply by removing lattices that meet a specified threshold as determined by the critical energy release rate of the rock. By introducing disorder in the model, mesh dependency in modelling fracture growth is minimized. Fluid flow is simplified as flow in pipe network and the permeability of pipe is related to fracture aperture by cubic flow law. Therefore, fracture flow and rock deformation are fully coupled. In this paper, four simulations of the same configuration except with different degrees of reservoir heterogeneity are presented. Fractures formed are diffusive and two groups of fracture are identified – connected fractures and isolated fracture without clear spatial correlation. The former forms a ‘fracture cloud’ and contributes to fluid flow and modeled by pipe network. The flow of fluid is highly tortuous and pipe network is sparely connected. The degree of reservoir heterogeneity controls the growth of ‘fracture cloud’ and pipe network. Microseismic monitoring often shows diffusive fracturing during HF on site and hence the outcome of the proposed model can be compared to such monitoring results.

Jan 1, 2015

By J. S. Redpath, W. R. Dengler

"A description of the equipment used and the electrical-mechanical problems encountered in sinking a deep shaft is given. This shaft is currently being sunk to a depth of 7,115 feet. Some of the features of the sinking plant are a 6,500-hp double-drum hoist, a Blair stage hoist, special high-capacity mucking gear, a Galloway stage, high-tensile stage suspension ropes and 12-ton sinking buckets.INTRODUCTIONIN THE EARLY FALL OF 1965, a contract was let, by The International Nickel Company of Canada, Limited, to Shaft Sinkers (Canada) Limited -J. S. Redpath Limited -Joint Venture, • to sink and equip the Creighton No. 9 shaft at their Creighton Mine proper-ty in Ontario. This paper describes the electrical and mechanical equipment used by the contractor on this project, and details various problems that were en-countered.The shaft itself is circular in section and is lined with monolithic concrete. Upon completion, it will feature twin skip compartments, a cage compartment, counterweight compartment, manway and pipe compartment. The finished diameter of this opening will be 21 feet and the shaft will bottom 7,115 feet below the collar. The present depth of the shaft (April, 1968) is 5,400 feet. The opening is concrete lined as excavation takes place and the steel will be placed in the shaft upon completion of sinking. Hoisting is done on rope guides which are part of the stage suspension system."

Jan 1, 1968

By V. L. Eardley-Wilmot

Diatomite as prepared for the market is a fluffy, white powder, remarkably light in weight-it weighs only 10 to 15 pounds per cubic foot, or one-tenth as much as sand. Being extremely porous and inert, it is in large and increasing demand for insulation and filtration purposes, as general filler, and for many other uses. Structure Structurally, diatomite is quite different from any other known commercial material. It is composed of myriads of microscopically small, siliceous shells of diatoms which belong to a group of flowerless aquatic plants called algae. When these plants die, the siliceous remains sink to the bottom of the water and form beds of diatomite. Over 8,000 species of diatoms are known, named, and tabulated. The intricate scroll-work and patterns on many of these are one of the marvels of nature, and yet so small are they that from 40 to 70 million separate diatoms may be contained in one cubic inch of material. However, the size and shape of these diatoms, which vary greatly (compare Figures 5 and 6), have an important bearing on the commercial use of the diatomite. The diatoms in the majority of the known deposits are so typical of that deposit that, after a micro-examination, an expert can usually tell not only from what part of the world, but also from what particular deposit, the sample has come.

Jan 1, 1931

By A. A. Goss

We investigate the relationship between corporate financial performance (CFP) and environmental and social performance (CSP) in a sample (n=165) of large, publicly traded U.S. mining and oil and gas firms. Using optimally scaled principal components analysis to generate aggregate measures of CSP strengths and concerns, we find higher concerns are related to higher volatility of unexpected earnings and discount rates. Furthermore, these earnings shocks are more likely to be negative as concerns increase. Decomposing this relationship shows that negative environmental performance dominates proactive environmental management as a driver of unexpected earnings, but proactive community efforts increase the magnitude of earnings shocks. We document some evidence of the strategic use of CSR, with those firms that have greater risk investing more proactively in CSR.

Aug 1, 2013

By George R. Pratt

Although the title of this paper focuses attention to the Winnipeg coal market the following remarks should be considered applicable not only to conditions in Winnipeg but to the whole western coal industry. Technical descriptions of coal and coal-burning have been omitted. These details are already covered in other numerous publications. In discussing a market the first consideration must be the product which is required to be sold. The class, quality and price at the point of origin must be taken into account and therefore this feature will be discussed before proceeding to outline conditions in the Winnipeg local market. The writer thinks of coal as a manufactured article, not, as it is generally considered, a fuel to be dug from the ground and dumped into the consumer's bin. The work of manufacturing must be considered in detail:- 1. Consider first the coal as it is in the ground: (a) What is its fuel value? (b) Where is its market? © With what will it be in competition? 2. Consider secondly: (a) What it will cost to mine the coal. (b) What has to be done to prepare the coal for market after it is mined. This must be considered in conjunction with the answer to question 1 ©. 3. Thirdly, consider the method of business to be adopted by the producer:- (a) Is it proposed to build a market on price? Or (b) On quality?

Jan 1, 1925

By P. Tracy

An advanced real-time monitoring system, called a "Tapblock Diagnostic System" is under development to help furnace operators manage the operation and maintenance of their tapblocks. The life of a water-cooled tap block in a smelting furnace ranges from several months to several years, depending on the operating conditions. Tapblocks are typically replaced at regular maintenance intervals; a strategy based largely on historical records and not on the actual condition of a particular tapblock. The Tapblock Diagnostic System monitors the tapblock throughout its life and accumulates probable wear events to help the operator assess the residual integrity of the tapblock. Benefits of this system include the ability to provide early warnings of tap block wear to provide improved safety and maintenance planning. Using cooling-water flow together with copper and water temperature measurements, the system performs calculations that compare the present tapblock performance with the expected operating envelope using a multivariate statistical method (Principle Component Analysis). The operating envelope is pre-calculated for a wide range of operating conditions using transient thermal modeling (Computational Fluid Dynamics). A state indicator in the form of a green, yellow and red light is used to inform operators of the tapblock performance and health status.

Jan 1, 2007

By S. McPhail, D. Richardson, G. J. Simandl, C. Akam, S. Paradis, M. Yakimoski, A. Teucher, Y. Cui, F. Ferri

Historically, extracting dissolved solids from formation water was economically motivated. Today, main drivers are environmental benefits and regulations, as large volumes of water needed for hydraulic fracturing require treatment before reuse or disposal. The concentration of dissolved solids in flowback water increases with each use and may require treatment prior to disposal. Element recovery from produced water is not profitable unless market conditions are favourable, recoverable elements are abundant, and economical recovery methods are established. Sale of recovered materials could offset recycling and disposal costs. This paper describes markets for Cl, Na, Ca, K, Sr, Mg, Br, Ba, I, B, and Li, and their concentrations in produced water from oil and gas wells in British Columbia. It recommends revising sampling protocol for produced water.

Jan 1, 2018

By Christopher R. Davis

Resource modelling is the basis for any economic appraisal of a mining project and includes a number of steps from data acquisition and validation to resource reporting and classification. At each step in the modelling process it is necessary to define the specific objectives, the methodology proposed to achieve those objectives and to establish a set of checks and validation tools to assess the effectiveness of the proposed methodology. The data used has to be both reliable and relevant for the purpose of the modelling. QA/QC for database validation requires verification of sample location; including correct collar location, topographic modelling and down-hole surveying. Validation is also performed on assaying information such as checks for sampling bias and accuracy of core splits, proper use of pulp duplicates and standards, handling of calculated values, explicit/implicit absent data and data entry errors. The second step involves identifying the mineralized domains resulting from the mineralization process. This step requires a geometric interpretation of all relevant geological features that have influenced the spatial distribution of the mineralization including dykes, faults and alteration. In addition, a geologic reference system rather than a standard Cartesian system is established to measure distances between samples. Once the mineralized domains are established and the database has been validated, statistical and spatial description of the mineralized samples are examined in order to establish the histogram and the variogram of all variables of interest and their correlation. Results are also used to calibrate the global resource estimate within the mineralized domain and to establish the search strategy for grade interpolation. The mineral envelope is filled with polyhedral cells representing mining blocks. The average grade of these blocks is estimated using kriging techniques in order to eliminate global bias and to minimize the local error in the block grade estimate. Visual checks are made to validate the spatial trends in grade distribution while global bias and smoothing effect are assessed from the declustered sample statistics. When required, smoothing correction may be applied using ?change of support? techniques. Simulations are used to perform sensitivity analysis and the simulation models are used if severe smoothing of spatial variability makes the interpolated model inappropriate for mine planning. The keys to successful resource estimation are an integrated team of geologists, geophysicists, geostatisticians and mine engineers using the best available technology and reviews by independent auditors. The resource team is also responsible for performing a QA/QC program in order to measure the effectiveness of the methods in meeting the specific objectives at each step of the modelling process.

May 1, 2001

By The Honourable George Prudham

"I AM PLEASED indeed to be present with you here today and to be taking part in the proceedings of your convention. You have been greeted and welcomed to the Province by Premier Manning who is also provincial Minister of Mines and Minerals, and to this City by Mayor Hawrelak. As Minister of Mines and Technical Surveys in the federal government and as Member of Parliament for Edmonton West, I have been asked to share the honour of extending greetings and a cordial welcome to all.It is a happy coincidence that this representative national gathering, indicative of the growing strength and significance of a great basic Canadian industry, is taking place in the Macdonald Hotel, the new addition of which marks another important step forward in the progress of this City and district.This happens to be the third national convention of the C.I.M. that I •have had the pleasure of attending and I trust that I am not presumptuous in expressing the hope that I will have the opportunity of attending many more conventions of the Institute in my present capacity.Dr. Kidd has bestowed on me a high honour by asking me to be Co-Chairman of this Inaugural Session of the Convention and thus to share with him the responsibility of presiding over the proceedings of this afternoon."

Jan 1, 1953

By L H. Warren

The types of equipment available for generating a plasma have been reviewed. The efficiency and potential of the plasma generating equipment used in performing extractive metallurgical reactions have been determined. A general classification of the reactions that might be per-formed in a plasma has been proposed. Experimental work done on extractive metallurgical plasma reactions, heat transfer between the plasma and solids, and the quench of the products of plasma reaction has been summarized. From the preliminary results it appears that the high-intensity are or the transpiration-cooled anode plasma torch offer the most promising areas for further research. C ONSIDERABLE world-wide research effort is currently being devoted to the development of processing technologies which employ the new high-temperature generating devices that have appeared over the past few years. The plasma flames produced by these devices offer the potential for subjecting materials to any single gas or mixture of gases at temperatures up to 20,000°K. With these conditions available, many reactions in extractive metallurgy,

Jan 1, 1965