Search Documents

By Michel Guillot

Gaz metal arc welding is commonly used for producing large frames and assemblies. Even for light aluminum and thin wall assemblies, the GMAW technique is increasingly preferred over the GTAW technique. This is particularly true where the welding gun motion is achieved accurately with automated or robotic systems and when using pulsed or regulated metal deposition. In this study, butt joints in floor welding position are tested at speed ranging from 1.5 to 16 m/min. Attempts are made of find parameters providing good and repeatable joint quality with minimal distortion and good appearance even at high travelling speeds. Taguchi experimental plans are proposed with different parameters tested with sheet metal samples. The parameters include typical GMAW machine settings, joint preparation geometries, wire gages, gun angles, wire feeds, and more. The robot motion speed and the proximity of the part are also considered. Direct monitoring of machine welding current and voltage is achieved. Once is found the best set of parameter settings, additional tests are carried out to verify the repeatability of weld quality. Secondly, these conditions are applied for joining and testing a floor panel made of several extrusions. Weld quality is established with Vickers micro-hardness measurements, cross section geometries of the weld pool including penetration, tensile tests and metallographic observations to establish the amount of porosity and weld microstructure in the HAZ.

Jan 1, 2011

By Manqiu Xu, Pete Winn, Steve Wilson

"In the flotation of ultramafic ores at Thompson mill, Inco Limited, CMC is used as both a floatable rock depressant and electrostatic serpentine slime dispersant. CMC, being a high molecular weight polymer, creates a serious handling problem in its introduction into the flotation processes. Typically, it is added as a 1-3% solution. This requires an enormous handling facility and makes its metallurgical gains uneconomical.Laboratory studies have shown that dry CMC addition as opposed to wet addition is feasible, as long as sufficient conditioning time is provided. Dry CMC addition into the grinding mill is also possible but its effectiveness is slightly reduced as compared to dry addition after grinding mills. Dry CMC addition using a vibratory feeder into the mill discharge is successfully applied in the treatment of ultramafic ores at Thompson mill.INTRODUCTIONManitoba Division MineralogyAt Inco’s Manitoba Division, two distinctly different sulphide ores are processed at the Thompson mill - primarily by froth flotation. The Thompson and Birchtree mines are both located within the Thompson Nickel belt. Sulphide mineralogy is relatively simple and includes both hexagonal and monoclinic pyrrhotite, pentlandite and minor chalcopyrite hosted in metasedimentary and metavolcanic rocks. The significant difference between the two mines is the amount of ultramafic rock associations in the host material. Increasingly, more of the ultramafic associated ores from the Birchtree mine are being processed through the mill with a characteristic poor metallurgy."

Jan 1, 2000

By Lucien Piché

"IN any opportunity such as I am now given, I suppose that one should not fail to say that what the world has to offer to this year's graduates in science and in engineering is the greatest promise ever held out. High-ranking new scientists and engineers -particularly those with the Ph.D. degree -find themselves in an apparently delightful situation; the glow of attention that surrounds them and the dazzling starting salaries that are offered to them may indeed be turning their heads a bit and the attitudes of some of them are sometimes expressed with a smugness that can find its equivalent only in freshmen. On the average, however, the new graduates are, without any doubt, the best trained ever, or at least they have been the most expensive to train in the universities.There appear to be exciting opportunities for competent, well-trained and educated scientists and engineers far beyond the numbers that can be annually produced, and the demands for excellence in depth as well as in breadth of training probably will continue to increase for many years to come. The problem is visible all around us in Canada that there is much more money to buy brains than there are brains to be bought."

Jan 1, 1966

By Christine Hansen

?Kiss my Asteroid? Unofficial Title Human life is tied to minerals It?s worth noting that: The living human body consumes minerals. The minerals we take in multivitamins show the close linkage between human beings and mineral resources. Unlike tourism or specialized manufacturing, a human being could not live without mineral consumption. Minerals and their consumption is a tangible part of human life.

May 1, 2013

By J. Wickens

"Campbell Mine is dedicated to quality management in the form of a Continuous Improvement (CI) Operating Philosophy. This paper discusses that philosophy, why and how it is being implemented in the milling facility, and some of the challenges experienced to date. Examples of mill CI team projects and results are described. This paper describes practical experiences for those who are considering or are in the process of adopting a CI operating Philosophy.INTRODUCTIONCampbell Mine is 100% owned and operated by Placer Dome Canada Ltd. The mine is located in Balmertown, Ontario approximately 300 km northeast of Winnipeg, Manitoba. Campbell Mine has produced over s,000,000 ounces of gold since commencing operation in 1949. The operation is profitable and continues to be a major contributor to the gold production of Placer Dome Inc.At Campbell Mine, the concept of Continuous Improvement (CI) is being implemented to make further improvements to safety, quality, productivity, and subsequently profits. CI is not a ""program"". It is a way of doing business that concentrates on improving the system rather than finding fault and being resigned to the status quo.CI focuses on involving all employees in the decision making process and tapping their expertise to improve every facet of the business. In the past, many solutions were simple ""band-aid"" fixes treating the symptom, only to see the problem resurface again. With CI, solutions endeavour to address the root cause of problems and eliminate them permanently. Another primary goal is to eliminate unilateral decisions that benefit a small group but have a negative effect on the whole system."

Jan 1, 1995

By R. C. Rowe

DR. W. F. GRAY (Contributed discussion, presented at meeting by Mr. S. C. Mifilen): Mr. Rowe's suggestion that the Institute should organize itself to interpret the needs of the mining industry to federal and provincial mines departments should commend itself to our membership as sensible and practical, and as one which these public administrative bodies may welcome. One has to start with the premise that those who head the departments of mines in question have the welfare of the industry at heart. Also, it must be postulated that the technical viewpoint of our membership is necessarily free of political considerations. With these reservations, one ventures to state that both Mr. Rowe in his communication to the present session of the Institute, and Professor M. Y. Williams in his earlier communication to the Western Meeting, on The Geological Survey and Mining Development (1), voice the regret general among our membership at the abandonment of the honoured name, and to some extent of the status, of the Geological Survey of Canada. The writer, in 1932, devoted his Presidential Address to the Institute to an appreciation of the value to Canadian mining of the Geological Survey of Canada (2), affirming the desire of the Institute "that the work of the Survey shall be maintained at the highest pitch of efficiency the resources of our country will permit, because, to scrimp expenses on the Survey, is 'to save at the spigot and lose at the bunghole'." He believes that is still the opinion of the Institute, and, if contraction of the usefulness of the Survey is feared by our members at this time, it is incumbent upon the Institute, in fairness to those who direct our government, to say so in precise and explicit terms. Mr. Rowe puts the situation pithily when he writes: "We have reached a stage in our development where a stock-taking and co-ordination of existing knowledge and data is essential. This is a part of that basic function of Dominion mineral technical services which is national and not provincial in its scope".

Jan 1, 1939

By George Kellock

In presenting this paper for discussion at the Western Annual Meeting to be held in Edmonton, it is with the idea of creating a full and general discussion by the mining men in the Province as to the best way to eliminate, or at least hold down to a minimum, the dangerous coal-dust which is made in mining pitching seams in our Alberta mines by the chute method. Also, an alternative method is outlined, whereby the percentage of lump-coal mined can be increased, and the mining costs reduced-although the paper does not go into any detailed consideration of costs. The general trend of mining practice and lay-outs is at present towards mechanization, and the results being accomplished by the substitution of machines for manual labour are fully justifying the changes. In the technical mining journals, there are published from time to time papers dealing with a variety of methods of mining, which are descriptions of actual operations, and a great deal of interesting and valuable data is given as to the comparative values of the different methods, insofar as the percentage of grades of coal produced, the cost of production, etc., are concerned; but the mechanical methods described in these papers are nearly always suitable only for flat seams, or seams with a very low inclination.

Jan 1, 1929

By B. R. Bowerman, W. J. Thoburn, M. J. Humphris

"Nickel granules are produced for carbonylation by pouring a molten stream into a path of high pressure water. Granules and water are separated in dewatering bins. The overflow, which contains up to 0.1 weight percent solids, was initially cooled and recycled to the granulating step. However, the rate of buildup of these solids in the handling system was intolerable. A lamella thickener was installed to solve the problem by removing solids from the dewatering bin overflow. Its description, application and performance to date are discussed.The lamella thickener treats a slurry containing about 0.1% solids of which about 30 weight percent is less than 325 mesh. It recovers 80 to 90 percent of the input solids in an underflow slurry containing 90 weight percent solids. Since its installation the frequency of cleanout of the recycle water handling system has dropped from about once per month to about once or twice per-year."

Jan 1, 1977

By M. Dupuis

It has been previously demonstrated [l] that there is no obvious thermal balance related issue limiting the size of a Hall-Héroult cell. Yet, it is well known that a forced-air sidewall cooling system is part of the AP50 cell design [2], In the present study, the authors analyze the impact of thermal loading on the mechanical deformation of high amperage cell potshells. The effect of adding cooling fins or a forced-air sidewall cooling system is then assessed.

Jan 1, 2005

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By M. J. Hadianfard

The effect of holding at temperature on fatigue life of a 10 vol% particulate SiC reinforced Titanium alloy has been investigated. The influence of holding time at 600°C on fatigue of this material has been studied by using tension-compression tests, scanning electron microscope and image analysis. The specimens were heated to 600°C by using a controlled atmosphere furnace; hold at this temperature for time ranging from 0 to 100 hours, and then fatigue tested at room temperature under controlled constant plastic strain. The number of cycle to failure found to decrease with increasing of the holding time. In addition the fracture mechanism and number of debonded particles has been significantly influenced by holding time at 600°C.

Jan 1, 2004

By Chandrakala Kari, Divyang Shah, Lakshmi Kanth Reddy, Kaushik Vakil, Sanjay Sarkar, Bhavin Desai

Gases rich in sulfur dioxide generated as a by-product of smelting and converting operations of copper concentrate contain selenium apart from zinc, lead, copper, cadmium, bismuth, antimony, and arsenic. The gaseous stream is heat exchanged in waste heat boiler, dust collected in electrostatic precipitator followed by cleaning in reverse jet scrubber to remove fumes, halogens and fine dust before passing to DCDA Monsanto catalytic converter to produce commercial grade sulfuric acid. The gas cleaning section of the acid plant uses water to scrub the smelting gases. During scrubbing, precipitated solids, known as sludge, settles at the bottom of the reverse jet scrubber containing 30 to 40 wt% copper and selenium up to 40 wt% selenium. In the existing process, the sludge collected during scrubber cleaning process is directly recycled to the smelter for copper recovery. However, the selenium is expected to again vaporize due to high oxidation potential during smelting and converting, causing accumulation of selenium in sludge. In present investigation, a roasting process has been developed to recover the selenium from acid plant sludge before charging it to smelter for copper recovery. Selenium is associated with copper in acid plant sludge as copper selenide, as determined by X-ray diffraction and electron microscopy. Thermodynamic and thermo-gravimetry study revealed that the copper selenide phase present in the sludge was amenable to oxidation at 600°C forming oxides of copper and selenium (Cu-Se-O). However, the dissociation of selenium from the copper oxide was made possible by sulfatation using sulfur dioxide between 450°C to 600°C, resulting into the formation of CuSO4(s) and SeO2(g). Lab scale experiments were carried out in vertical tubular furnace to determine the optimum roasting conditions with respect to roasting time, temperature and molar ratio of O2:SO2. Using these optimum conditions, selenium up to 90 wt. % in the form of SeO2 vapors could be recovered from the acid plant sludge in a large scale commercial roaster. Roasted sludge free from selenium and containing oxides and sulfates of copper could now be recycled in the smelter for copper recovery. INTRODUCTION There is an increasing demand for minor metals due to their use in innovative technologies. Similarly, the increase in demand for selenium is expected due to disruption in sectors related to renewable energy and photovoltaic battery. Selenium is a chalcogen and a non-metal with black or red crystalline appearance. Selenium is used in the glass industry to decolorize glass and to make red-colored glasses and enamels. It is also used in solar cells and as a photographic toner. Selenium is used as a brasses in stainless steel to improve its machinability. Selenium sulfide is used in anti-dandruff shampoos. In spite of the toxicity of its compounds, selenium is also an essential trace element for humans and animals. Selenium occasionally occurs free in nature, but more often occurs as selenides of iron, lead, silver and copper. There is an urgent need for the development of new methods for selenium recovery from the existing resources. Commercially, selenium is obtained only from anode mud produced during electrolytic refinery of copper.

Jan 1, 2019

By M. Jarvis, D. B. Dreisinger, T. Hitchins

Mineral carbonation (MC) has been extensively researched all over the world since it was found as a natural exothermic process to permanently and safely sequester CO2. In order to accelerate the natural process, various methods for carbonation of Mg-/Ca-silicate minerals and other industrial wastes have been studied. It has been found that the MC efficiency will increase with an increase of CO2 pressure, retention time, temperature, mass ratio of Mg or Ca to Si in minerals, specific surface area, and the slurry concentration in a specific range, and with the introduction of an effective catalysts, for example, 1M NaCl and 0.64M NaHCO3 or carbonic anhydrase. However, there still is not a successful industrial application because of high economic cost and slow reaction rate. It is not economic to exploit Mg- and Ca-silicate minerals deposits or tailings to sequester CO2 by MC, due to the cost of grinding and heat pre-treatment and in some cases the whole sequestration process may result in more CO2 emissions than the amount of CO2 sequestered, due to the requirements of energy inputs. The process however, may be profitable as a whole (with carbon credits). It is suggested to combine MC with recovery of valuable metals from ore deposits in order to reduce the cost for MC by cost sharing for mineral recovery.

Jan 1, 2017

By M. M. Papic

"This paper describes the Sasol coal liquefaction process, as used in South Africa. It covers coal supply, coal gasification, gas purification, Fischer-Tropsch synthesis, the major utility systems involved and the economics of the process.IntroductionThe Sasol coal liquefaction process is based on Fischer-Tropsch synthesis of liquid fuels from carbon monoxide and hydrogen, which are in turn obtained by gasification of coal with steam and oxygen. The process is shown schematically in Figure I.The first step in the process is coal preparation, in which the coal is crushed and screened to a 3-50 mm size for gasification on one side and to -3 mm size for steam and power production on the other. Oxygen needed for coal gasificatoin is produced in the air separation plant.Coal is gasified under pressure by steam and oxygen in the Lurgi gasification plant, where raw, impure gas is produced . The raw gas is first washed in a scrubber with a circulating gas liquor, heat is then recovered from it in a waste heat recovery boiler and the gas is further cooled for purification. Water-insoluble materials (tar oils) in the gas liquor are separated from aqueous solution and sent to tar refining for the recovery of tar products. The aqueous portion of the gas liquor goes to a Phenosolvan solvent extraction process, where phenols and ammonia are recovered. Water then proceeds to the effluent treatment plant.The scrubbed and cooled raw gas goes to a Rectisol gas purification plant, where all components other than hydrogen, carbon monoxide and methane are removed as completely as possible by absorption in refrigerated methanol. The acid gases (CO2, H2S) stripped from the methanol in the Rectisol unit are processed in a Stretford plant for recovery of sulphur. Regenerated methanol is returned to the process. The purified synthesis gas is passed to the fluidized-bed Synthol reactors, where Fischer-Tropsch synthesis reactions take place.The synthesis products are recovered in a product recovery unit as separate streams of decant oil containing higher-molecular- weight hydrocarbons, light oil comprised of lower-molecular- weight species, the aqueous stream containing water solubles, a C3/C4 stream, a C2 stream , a methane stream and a hydrogen-rich stream. Most of the hydrogen is recycled to the Synthol reactors; a major portion of the methane is reformed to hydrogen and carbon monoxide for recycle; the C2 fraction goes to an ethylene plant; and liquid streams proceed to the product refinery.The product refinery is used to upgrade and purify the Synthol products to specification fuels and chemicals.Sasol l, the first coal liquefaction plant in South Africa , was built in 1955. It is still operating and has a product output of about half a million tonnes per year. The Sasol II plant is in a commissioning stage and will be in full operation in 1981. It is about five times the size of Sasoll. It uses over 12 million tonnes of coal and produces more than 2 million tonnes of saleable products annually (1,2,3). The Sasol llI plant, which is a mirror image of Sasol II, is under construction and scheduled for completion in 1983."

Jan 1, 1981

By Raymond C. Voige

"The use of current electronic technology in the design of new underground mine communications equipment is providing improved and expanded voice communications which can, in turn, contribute to improved productivity and safety. A review of equipment that is now available or under development Includes the following categories:WIRED SYSTEMSI.Pager phones with selective calling, audible and visual alerting and message indicator.2. Mufti-conversation pager phones that use multiwire cable ormultiplexing techniques.WIRELESS SYSTEMSLow-and medium-frequency inductive systems utilizing ""near"" magnetic fields for both vehicular and personal communications.Wired SystemsCommunication systems in underground mines have evolved slowly in many parts of the world. For many years, magnetotype telephones were the only means of communication from one mine level to another and to the surface. These units were located near the shaft and communications to the working areas were limited."

Jan 1, 1981

By T. Schmidt, H. Assadi, F. Gartner, H. Kreye

Among all spraying processes, cold spraying has attracted a special attention in recent years, both as a coating - and more recently - as a rapid manufacturing technique. The interest in this process is mainly because of the fact that the deposition of spray material takes place at moderately low temperatures, and thus, oxidation and unfavourable microstructural changes can be alleviated. In this process, a highly compressed gas, flowing through a de Laval nozzle, accelerates the particles of the spray powder to high velocities of up to 1200 m/s. Although there is no melting of particles prior to impact on the substrate, cold-sprayed deposits can be denser and more tightly bonded as compared to the equivalent deposits produced by conventional thermal spraying methods. The present contribution focuses on this unique aspect of cold spraying. Modelling of particle impact, combined with various experimental observations, is employed to illustrate that bonding of particles and hence material deposition occurs through shear instability - associated with severe plastic deformation and localized heat generation - at the interacting surfaces of particles and substrate. The results of modelling also provide an insight to the influence of material and process parameters on the critical velocity and on the microstructural properties of cold-sprayed deposits.

Jan 1, 2006

By A. Lopez-Valdivieso

Particle size enlargement processes play an important role in solid/liquid separation, and in beneficiation unit operations. In the latter, not only the size of the formed aggregates but also their surface properties are very important. Oil agglomeration has a special place among such processes: it is a selective process in which hydrophobic particles are agglomerated into hydrophobic agglomerates which can be recovered by flotation. This explains the broad applications of oil-assisted beneficiation processes not only in the beneficiation of fine coal, but also in agglomerate flotation of many different types of ores, and in coal/gold agglomeration.

Jan 1, 2004

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By Fiona Campbell

"Modern history is full of breakthroughs in technology, all striving to increase productivity and efficiency. What are the elements that should be taken into consideration in the design and implementation of modern automation systems in a control room? Both industry and international standards are now demanding that Human Factors be considered as part of the design of control rooms to maximize efficiency and minimize the potential of human error which can lead to downtime and a loss of profit as a result of interruptions in production. As the current workforce ages and the younger generation matures, this is also becoming a key element when planning a control room. New standards are helping to address some of these challenges that are facing the mining industry today. With an increased focus on the operator, an intelligent and ergonomic workspace can both mitigate risk and optimize production. Optimization is money. We will examine how to analyze and implement innovative control room planning to maximize mineral processing production and minimize risks that can impact overall production and profit.INTRODUCTIONIn this day and age, optimization of production in an industrial environment is becoming more and more of a challenge. With ever changing technology as well as other external factors, this can be especially daunting. There are several key elements that may not be immediately obvious when planning a control room design or renovation, most notably the role of the human in this environment. Fatigue, stress, distraction, reaction times and situational awareness are all critical in a 24/7 environment. With the growing need to include human factors when considering and designing an optimal work and production environment, it is becoming even more important to design a control room that can address as many of today’s challenges as possible.The standard definition of the word “optimization” is “an act, process or methodology of making something (as a design, system, or decision) as fully perfect, functional or effective as possible.” (www.merriam-webster.com). If we apply this to business, what it really means is finding the most cost effective way to achieve the highest level of performance while considering constraints, both external and internal, by maximizing the desired factors and minimizing undesired ones. Sometimes, however, we can get caught up in the day to day processes, without taking a moment to step back and objectively review what it is we need to achieve, and more importantly, the steps that can facilitate our success."

Jan 1, 2016

By Chris V. Sellathamby

Condition-based maintenance is replacing preventive maintenance in many industrial operations as a result of gains in productivity. Preventive maintenance is strictly time-based which means that as long as the prescribed time is sufficiently short, failures are prevented. The trade-offs between shorter cycles and increased downtime is a fine balancing act. Condition-based maintenance is gaining momentum as the more cost-effective and green solution to finding the optimal maintenance cycle and improving overall productivity. In the mining industry, various parameters of heavy equipment are monitored continuously to provide feedback for maintenance events. However, strain, shock, and vibration, key factors which lead to yielding and fatigue of metal parts, are not generally monitored by built-in systems, mainly due to the complexity of sensor installation and computational intensity of data processing. Scanimetrics has developed a stand-alone, add-on wireless system for measuring strain, shock, and vibration in heavy equipment and components, the data from which can be directly used to trigger maintenance events. The present system is being deployed in tar sands mining equipment. The system consists of a portable display and control unit, a software platform consisting of data management, sensor instrumentation and data analysis, and wireless strain sensor units, which can be easily installed on equipment. Data from the sensors can be gathered throughout the mine site, processed instantly, and used to generate condition-based maintenance events, improving overall uptime of the equipment and overall productivity of the mining operation.

Oct 1, 2010