Search Documents

By J B. Magee

Sheep Creek Mines Limited has developed several operating techniques that have greatly assisted in keeping unit costs at reasonable levels. Some of the techniques, as described in this paper, include organization, accounting, warehousing, bonus and contracts. INTRODUCTION THIS paper is a non-technical report on operating techniques developed by Sheep Creek Mines Limited at their Mineral King mine, located near lnvermere, B.C. Depressed metal prices and continually rising labour and materials costs have necessitated a continuous search for method to keep operating costs down. The newly developed techniques and practices have greatly assisted in maintaining unit costs. Sheep Creek Mines Limited is a mining company incorporated under the laws of the Province of British Columbia. The Company's share capital is 3,500,000 common shares, witl1 a par value of 50 cents each, of which there are 1,875 000 shares is-sued. The Company has eight di-rectors. The administration, exploration and accounting offices are located in Nelson, B.C. The Company's working capital is approximately $1,500,000.

Jan 1, 1963

By ManhKha Trinh, Neal Pyke

Dofasco was the first company to adopt oxygen steelmaking in North America in 1954, two years after the first LD vessel installed and operated successfully in Linz, Austria. Since then, Dofasco has investigated and implemented several strategies to maximize hot metal usage and minimize overall cost. Some key strategies -low hot metal silicon, combined blowing conversion, vacuum degassing tank upgrade and BOF slag carryover control - are discussed. Post combustion, scrap preheat, carbon injection trials along with current operating philosophies are described.

Jan 1, 2004

By W. Swidzinski

"Zelazny Most" post-flotation copper mine tailings pond is the only place to of storeing wastes for KGHM POLSKA MI EDZ S.A. The flotation tailings is are the main waste stream in copper mining in Poland. Sufficient storage capacity for tailings is crucial for , thus uninterrupted production of copper is crucially related to the possibility of storing wastes in the pond. The pond covers a Its over 14 km2 arca, almost 50 m high dams making this dame this construction one of the largest in the world. The risk assessment of potential damage due to un stable ility loss of dams or environmental contamination, as well as safely constructing damsincrease of dams within the design criteriaprocess, require quick access to a large amount of the monitoring data , which in vast amount have to be monitored, that needs to be analyzed and processed and reported, every day. This In the paper describes the numerical information system "SyZeM" , used for designated to the "Zelazny Most" pond, baseding on the Oracle database and Geographical Information System , to manage the graphical and descriptive data in coherent way., is presented. The main structure of the system, as well as the methodology of storing, processing and reporting the geological, geotechnical, hydrogeological, geophysical, chemical and survey data are shown. The aspects of Optimizing optimal and risk mitigation and safe management of copper wastes and risk mitigation with the help of "SyZeM" are discussed.

Jan 1, 2007

By S. Hopkins, R. Preston, S. Gillis

"This paper examines typical visual inspections of operational soft rock mine shafts and discusses some of the challenges involved, many of which are associated with inconsistent inspection practices. The paper presents the development of a more standardized approach to periodic shaft inspections that supplement the more frequent inspections performed by shaft crews at the mine. This approach helps to keep an accurate record of changing conditions, compare conditions between multiple mine sites, as well as prioritize and plan potential remedial work. INTRODUCTION Shaft inspections, whether they are performed daily or weekly by members of the shaft crew at the mine, or periodically by consultants, traditionally involve a visual inspection undertaken with personnel traveling on an inspection deck on the conveyance, taking notes and photos. Inspections are typically required by mining regulations and carried out to identify and address hazards before a safety incident occurs that could cause harm to people or damage to property, as well as to help plan required maintenance work. Depending on the site, there can be many challenges associated with inspections in the shaft, especially compared to a typical inspection at surface. Some of these challenges are associated with the shaft environment itself, while others are related to the subjectivity of inspections and a lack of standardization, particularly between multiple sites within the same operating company. Recognizing these challenges, a more consistent and repeatable approach to shaft inspections in soft rock mines is evolving. This approach involves reviewing available historical data, comparing sites with similar conditions, establishing survey control, documenting observations and measurements with locations, and updating as-built or condition drawings. Part of this standardized approach is the implementation of an innovative 360-degree camera with a high-power lighting system that can be used either remotely or alongside personnel completing a traditional visual inspection. The system uses six cameras to take photos at a rate of 15 frames per second, with the image data subsequently processed and stitched, then joined into a high-resolution video. This tool improves time-efficiency, objectivity, and repeatability of inspections."

Jan 1, 2019

By C. S. Simons, D. A. Dahlstrom

"Growing interest in the developing technique of improving the dewatering of filter cakes by the direct application of steam has been apparent during the past year. A number of applications to iron and base-metal concentrates are under study, and intensive work continues on applications to coal cleaning.This paper presents and discusses the data presently available. The effects of material characteristics and operating variables on final cake moisture are examined. Although it is not yet possible to answer all questions regarding the applicability of the technique to specific problems from general data correlations, it is found that the use of these in con-junction with empirical data derived from properly conducted laboratory tests does yield reliable conclusions.Emphasis is placed on the basic economics of the process, and on de-sign criteria for ""steam drying"" filter stations, as applied particularly to metallurgical concentrates. Examples of the use of laboratory tests to solve application problems are given."

Jan 1, 1966

By W. A. Lang

Introduction That the coal industry has entered a new phase in its development is now evident. Coal, besides being the chief source of heat and power, has become a potential raw material for many industries. Rapid progress has been made in the methods used in the mining and preparation of coal, and in the equipment for the burning of coal. Data of a fundamental nature relating to the composition of coal and to its transformations? during combustion and processing have also been revealed. Research, the key which has opened this new era, has already accomplished much, but it has only begun to show what it may and should be able to do. New developments of coal burning equipment, super-power plants, carbonizing and briquetting plants, hydrogenation and synthetic chemical processes, will undoubtedly have a marked influence in the post-war years on the economic welfare of many coal producing countries. Until comparatively recently, however, there has been in many branches of the coal industry a tendency to regard research as something abstruse and something which had little or no value to those managing such branches. But the fact that coal has suffered as a source of heat and energy through inroads of oil, natural gas, and water power, has made it plain to the industry that, if it is to maintain its present markets in this competitive world, much less increase them, the whole industry must be willing to follow the example of other industries and plan for the future.

Jan 1, 1946

By S. C. Ellis

THE bituminous sand of northern Alberta has already an extensive literature, and most of the reports dealing with the subject are still available (see Selected Bibliography at end of paper). A phenomenon so striking and, as regards its extent, so unique, as the deposit in the vicinity of McMurray settlement could not fail to attract the notice of the early explorers, and we find references to it as far back as the latter part of the eighteenth century. However, scarcely a thought had been bestowed upon the possible economic value of minerals in the the remote northern parts of Canada before the second decade of the present century, and practically no detailed mapping had been done north of the town of Athabaska. The late Wm. Ogilvie made a track survey of Athabaska river in 1884, and surveys of certain lines-including the 23rd base line-had been completed by 1911. Between this base line and lake Athabaska, nothing had been attempted. Actually, no definite information at all was available regarding the character and extent of the bituminous sand when, in the earl y summer of 1913, a reconnaissance party set out from Athabaska for McMurray. At that period, the journey was made in summer by scow or canoe. No telegraph line had been laid, and a casual mail service by canoe or dog team once in three months formed the only means of communication with the outside world. The investigation has begun by the Mines Branch was continued during several subsequent years. The sand deposits were studied and sampled, the bi rumen was extracted from the sand and studied chemically and physically, and the economic significance of the deposit was given exhaustive study.

Jan 1, 1937

By B. F. Haanel

IN the fall of 1929, a paper was presented at the Annual Western Meeting of the Institute entitled The Fuel Research Laboratories at Ottawa and the Scope of Their Investigations. At that time, the equipment of the laboratories had not been completely installed, but the regular routine work was being carried on as usual, and several large-scale investigations were being conducted. It is now five years since that paper was presented, and it seems fitting that a brief description of the investigations which have been undertaken, together with results-especially those which have reference to western Canadian fuels-be presented at this Annual Western Meeting. The coal mining industry of western Canada has, within the past few years, suffered many unfortunate vicissitudes. The replacement of coals by oil, for bunkering ships, for operating railway locomotives, and for heating, has weighed heavily on the coal mining industry of British Columbia and Alberta generally, but more particularly in the Crowsnest Pass area and Vancouver-and hydro-electric developments have also left their impress. With a full appreciation of these conditions, the Department of Mines planned research and large-scale investigations which it was considered would be of the greatest benefit to the coal industry, and the results have amply justified the plans and anticipations. The fact, however, must not be lost sight of, that the application of the findings of certain of these investigations would not have been feasible had not the Federal Government assisted the transportation of coal by the application of railway subventions. These subventions permitted Canadian coals to compete at competitive points with United States coals, and it must be admitted also in this connection that certain of the collieries which have benefitted, both as a result of the railway subventions and the investigations conducted by the Fuel Research Laboratories of the Department of Mines, made special efforts to produce a coal which was capable of competing with the American product, by special preparation at the mines.

Jan 1, 1936

By N. Dave

"IntroductionIn the mineral processing industry, certain minerals such as uranium, thorium and vanadium, etc., are selectively extracted with high degree of purity from solutions containing variety of other impurities by solvent extraction process. This separation process consists of bringing two immiscible or partially soluble liquid phases in contact, where mass transfer of one or more components takes place by ion exchange under certain controlling parameters such as pH, salt concentration and temperature. The processes taking place are primarily physical because the solutes being transferred are ordinarily recovered without chemical change. For efficient extraction more than one stage is required and the solutions are recycled counter currently through other stages. A multi-stage counter current solvent extraction plants essentially consist of four circuits namely: extraction, water wash, stripping, and solvent scrubbing. In extraction circuit the desired mineral is extracted at a certain pH from an aqueous solution onto an organic solvent by bringing them in contact with mixing in large mixer-settler units. The mixed solutions are allowed to settle and separate into component organic and aqueous phases in horizontal settlers by providing sufficient residence time. The solutions are then moved counter currently to other units- the aqueous from the underflow and the solvent organics from the overflow of the settler. The solution streams coming out of extraction circuit are loaded organics and barren aqueous or raffinate solution. The loaded organics are washed with water in a water wash circuit to remove transported impurities from extraction circuit. In the stripping circuit, the desired mineral is stripped selectively from the solvent phase back into an aqueous phase with a stripping agent at a selected pH. The solution stream leaving, stripping circuit are stripped organics and pregnant strip (aqueous) solution. The stripped organics are scrubbed off other loaded impurities with a conditioning solution in, scrubbing circuit and the cleaned solvent is re-used in the extraction circuit.A typical solvent extraction plant for uranium extraction and purification at Agnew Lake Mine is described in this chapter."

Jan 1, 1989

By R. D. Clarke, E. De Souza

"A framework for ventilation planning, with a focus on planning to the end-of-mine life, was developed for the Diavik Diamond Mine, Northwest Territories. This framework was successfully used by Diavik’s mine engineers to select a cost-effective ventilation plan that met the life-of-mine requirements. The framework achieved this result by reconciling the production plan with the ventilation plan. A set of design acceptability criteria was created and a PICK (possible, implement, challenge, kill) chart was used to quickly narrow down the generated ideas for detailed assessment and economic analysis. RÉSUMÉ Un cadre de planification de l’aérage, qui met notamment l’accent sur la planification jusqu’à la fin de vie de la mine, a été développé pour la mine de diamants Diavik. Les ingénieurs miniers de Diavik ont su mettre à profit ce cadre pour sélectionner un plan d’aérage rentable qui répondait aux exigences propres à la durée de vie de la mine. C’est en conciliant le plan de production et le plan d’aérage que cet objectif a pu être atteint. Un ensemble de critères d’acceptabilité de la conception a été créé et un tableau PICK (de l’anglais possible, implement, challenge, kill, une méthode donnant la priorité à certaines actions proposées ou à des idées visant à résoudre des problèmes) a été utilisé pour rapidement limiter les idées générées et les soumettre à une évaluation et une analyse économique détaillées.INTRODUCTION The Diavik Diamond Mine, Northwest Territories, has been an underground-only operation since 2012 and has a remaining mine life of 8 years. In the first year of underground-only operations, the production rate increased from 60 kt of ore per month to more than 160 kt of ore per month. In subsequent years, this rate was continuously increased (Table 1) because the operation went through various improvement initiatives. By the end of 2016, Diavik’s total production was 0.41 Mt (+22.8%) ahead of the 2012 budget for 2016 production."

Jan 1, 2018

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By Ralph Johnson, Philippe Gaultier, Loui Fauteux, Andrew Dasys

"This paper outlines the implementation of the Mechanic's Stethoscope from the earliest stages of development to the implementation at Brunswick Mining and Smelting. It details the cooperative efforts of personnel at Noranda Technology Centre (NTC) and Brunswick Mining & Smelting (BMS) during the technology transfer of the Mechanic's Stethoscope. It demonstrates how everyone worked toward a goal of developing a product that is accepted as a useful addition to the work environment.The Mechanic's Stethoscope is an underground vehicle diagnostic system consisting of computer hardware and software intended to assist mechanics in daily tasks. Its tools facilitate quick and easy access to any information required during the maintenance of an underground vehicle. Each tool presents vehicle condition data in a simplified manner. The additional information improves the mechanics understanding of the vehicle condition. The result is a healthier fleet of vehicles and faster diagnosis times.When introducing a computer based system into a traditionally non-computer oriented environment a concern is the acceptance of the system. This concern exists on many levels."

Jan 1, 1995

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

By U. Erb, L. Monaco

"Electrodeposited nanomaterials are increasingly implemented in advanced industrial applications in the aerospace, automotive, defence, electronic and energy sectors due to their outstanding physical, chemical and mechanical properties, including increased strength and wear resistance, and superb magnetic properties. As with the development of any class of new materials, the corrosion behaviour of these electrodeposits requires considerable attention. This presentation reviews major developments in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites over the last 20 years, with emphasis on how their intrinsically high density of intercrystalline defects does not compromise their corrosion resistance as initially expected.INTRODUCTIONOver the past 20 years there have been considerable advances in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites. In this paper, the corrosion properties of nanocrystalline nickel, cobalt, zinc, and copper and some of their alloys are reviewed with emphasis on how a reduction in grain size affects their corrosion behaviour in different environments.It is possible to synthesize nanocrystalline material with microstructural refinement down to the range of 1 to 100 nm using a large number of processing methods. There are five basic synthesis methods that can be used to classify the different techniques: vapor-phase processing, liquid-phase processing, solid-phase processing, chemical synthesis, and electrochemical synthesis. Depending on the synthesis method, different microstructures (equiaxed, textured), shapes, and forms (films, particles, bulk material) may be produced. In addition, other factors may be introduced (eg. residual porosity or amorphous phases), aside from microstructural refinement, which can contribute to the observed properties (Erb, 2010). In order to interpret and categorize the resulting microstructures, a dimensional structure modulation scheme was introduced by Siegel (1996) in which zero-dimensional nanomaterials refer to individual particles, clusters, etc. One-dimensionality results from a layered (less than 100 nm thick) structure. Two-dimensional nanomaterials are thin, layered structures containing grains (less than 100 nm) within each layer. Finally, three-dimensional nanomaterials are bulk structures with an average grain size less than 100 nm."

Jan 1, 2012

By P. Mundell, R. Torbin

"There are many physical and operational obstacles in pipelines that make the passage of inspection robots impossible including:•,Small radius bends•,Low operating pressure•,Plug valves•,Large changes in pipe size•,No permanent access to the pipeline.The inspection of unpiggable pipelines requires the marriage of a highly agile robotic platform with NDE sensor technology operating as an integrated system. Foster-Miller and GE/PII are developing a robot that is essentially a battery powered, train-like platform. Both front and rear tractors propel the train in either the downstream or upstream direction. Like a train, the platform includes additional ""cars"" to carry the required payloads. The cars are used for various purposes including the NDE sensor module(s), the power supply, and data acquisition/storage components. The robot is designed with a slender aspect ratio and the ability to change shape as required by the physical obstacle presenting itself. The MFL sensor module must also morph itself through the physical obstacles, and thus, will require some level of segmentation. The segmented MFL magnetizers and transformable sensor module represent a major advance in the science of sensor technology and pipeline inspection."

Jan 1, 2005

By E. G. Bazeley

The paper reviews the scope, timing and financial impact of this significant project, which involves the supply and transportation of nearly 4 million tons per year of bituminous coal and lignite from sources in British Columbia. Alberta and Saskatchewan to Ontario Hydro's generating stations. The critical factors involved in the selection and utilization of these coals are discussed in relation to the three types of coal to be utilized initially. The paper then deals with each of the significant project elements to be undertaken by the various companies involved in the mining and movement of the coal, beginning with production at the mine through rail shipment to Thunder Bay, train-to-ship terminalling, shipment by lake vessel from there to the generating station, and finally blending the bituminous coal with United States coal prior to combustion. The review discusses the key features of the facilities involved in each case and the status and timing of the project elements , which are phased for the start of coal shipment by mid-1978. The paper concludes with some observations on the capability of the project to handle increased tonnage s and the challenges facing the movement in terms of quality , quantity and cost.

Jan 1, 1978

By G. N. A. Senhorinho, J. A. Scott, C. A. Laamanen

"Closed mine sites are widely regarded as a negative asset due to their legacy of environmental impacts. These sites are often characterized by waterbodies with elevated metal concentrations and low pH that are traditionally considered to have little or no value. These sites are potential sources of beneficial biocompounds produced by microalgae in response to environmental stresses. A bio¬prospecting program found that certain microalgae from waterbodies near historical mine sites exhibited higher antibacterial activity than any microalgae previously reported in the literature. There is potential for the mining industry to be involved in examining features such as tailings ponds at mine sites for high-value compounds, including ones that might help mitigate rapidly growing microbial resistance to current antibiotics. ¦ KEYWORDS Antibacterial, Closed mining sites, Metabolites, Microalgae, Stressed environments RÉSUMÉ Les sites miniers clôturés sont généralement considérés comme des actifs négatifs en raison de leurs répercussions sur l’environnement. On trouve souvent sur ces sites des étendues d’eau affichant de fortes concentrations en métaux et un pH faible, généralement considérées comme ayant peu, voire pas de valeur. Ces sites sont des sources potentielles de biocomposants bénéfiques produits par des microalgues en réponse aux perturbations environnementales. Un programme de bioprospection a permis de déterminer que certaines microalgues trouvées dans ces étendues d’eau à proximité de sites miniers historiques présentaient une activité antibactérienne supérieure à celle mentionnée dans toute la docu¬mentation existante. L’industrie minière pourrait bien participer à l’examen de particularités telles que la recherche de composants à haute valeur dans des bassins de décantation des résidus sur des sites miniers, notamment des composants qui pourraient aider à atténuer l’augmentation rapide de la résistance micro¬bienne aux antibiotiques actuels. ¦ MOTS CLÉS antibactérien, environnements perturbés, métabolites, microalgues, sites miniers clôturésINTRODUCTION The mining industry is one of the largest economic drivers in the world. Within Canada, for example, it contributed 2.8% (C$57.6 billion) of the 2016 gross domestic product (Marshall, 2016). Canada also has the highest non-ferrous exploration budget worldwide (Marshall, 2016); therefore, it is likely that mining operations, mine waste disposal, and the number of closed sites will continue to grow in Canada. The environmental impact of mining operations stems from the volume of tailings produced, which can be up to 97–99% of the total volume of ore processed at a mine (Adiansyah, Rosano, Vink, & Keir, 2015). In 2010, mining was the world’s largest industrial producer of waste at a total of 65 billion tonnes: 51 billion tonnes of waste rock (mine overburden) and 14 billion tonnes of tail¬ings (Jones & Boger, 2012)."

Jan 1, 2019

By G. M. Proudfoot

IN June, 1940, a .Longyear 3420 blast-hole drill rig was purchased by the Hudson Bay Mining and Smelting Company for the purpose of experimental blast-hole drilling. The early work showed that the diamond drill could compete successfully with the Leyners then in use and by January 1st, 1941, the diamond drills were placed on contract. They may be considered to have gone into production at that date. Prior to the introduction of the diamond drill, our bench drilling was clone with Ingersoll-Rand S-70 and S-83 Leyner drills. Holes up to 40 feet were drilled, using coupled 1 1/4-inch round steel. Bits with a gauge of 3 inches were used in starting these holes, with a drop of 1/8-inch gauge for each 2-foot run. The holes normally ended with 1 1/2 or 1 5/8-inch gauge, though bits down to 1 1/8 inches were available for holes longer than normal or for holes drilled in abnormally abrasive ground. This method of drilling was very satisfactory and was a distinct improvement on the three-bench method of drilling used previously (1). During 1937 and 1938, when experienced miners were available, Leyner long-hole drilling was carried on with great efficiency. However, in 1939 and 1940, labour turnover in-creased and experienced long-hole drillers became scarcer. This resulted in a marked decline in the efficiency of the drilling operations, with increased costs and less tonnage drilled per shift. EXPERIMENTAL WORK The initial diamond drilling test work was carried on with a Longyear 3420 air-driven blast-hole drill rig, drilling a 1 3/16-inch hole. Tests indicated that diamond drilling could be successfully adapted to local conditions and that overall costs compared favourably with costs obtained with the Leyner long-hole method. Leyner long holes on stope benches usually bottomed at a larger diameter than the 1 3/16 -inch diamond-drill holes. More powder could therefore be introduced into the Leyner holes than could be placed in the diamond-drill holes. To achieve the same fragmentation, additional footage was required when diamond drilling. Diamond-drill holes of larger diameter were indicated.

Jan 1, 1943

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006