Search Documents

By Stephen L. Chryssoulis

"""Preg-robbing"" of gold by carbonaceous matter during the cyanidation of certain types of carbonaceous gold ores is well documented. Recent studies established that ""preg-robbing"" of gold is not limited to carbonaceous matter. Gold sorbed on the surface of pyrite grains was detected and quantified by TOF-LIMS (Time of Flight Laser Ionization Mass Spectrometry). Crystallites of pyrite from a number of ores from different geological environments have been shown to have gold on their surface apparently sorbed from the ore forming solutions. Surface gold accounts for significant fractions of the gold head assay. Preg-robbing of gold by pyrite from pregnant cyanide solutions was also documented, and accounts for significant losses to tailings. Preventative measures are discussed.1.0 IntroductionThe detection and subsequent quantification of gold sorbed on the surface of pyrite particulates came about during routine determinations of the deportment of gold employing the comprehensive mineralogical approach (Chryssoulis and Cabri, 1990). In some pyritic gold ores it was discovered that the sum of the various forms in which gold ""conventionally"" occurs, was short of the gold assay. The mineralogical procedure used involves the independent determination of each fraction of gold, in other words there is no form of gold which is calculated ""by difference"". The systematic shortfall after having added the forms of gold listed in Table 1 led to the inquiry for the 'missing' gold and its discovery on the surface of pyrite grains, such as crystal facets and fractured surfaces.Preg-robbing of gold by pyrite from pregnant solutions was first described by Lloyd. In his studies, preg-robbing was measured by changes in the solutions/solids gold assays. This paper describes the first application of a direct measurement method for surface gold on pyrite particles from untreated and processed samples, its impact on gold deportment and processing. The advantage of the direct measurement lies in the absence of interference from other forms of gold, leading to more accurate and precise determinations of this unconventional form of gold."

Jan 1, 1997

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"The steps from experimental curiosity through to commercial product can be slow and tortuous in spite of the quality of the technological advances offered by the new development. Data generation and interpretation need to be done in lab tests as well as full-scale evaluations and, in each, the advantages of the new reagent must be clearly identifiable and measurable.The Dow Chemical Company has patented a novel new collector for the flotation of zinc. Fl (2-hexylthioethylamine hydrochloride) has several unique structural features that suggest atypical mechanisms for zinc collection. Laboratory data have demonstrated significant flexibility with respect to grade and recovery balance at dosages lower than those typically used for xanthates.In mill trials, the same phenomanon is evident - the choice between high grade and high recovery allows one to select the desired quality of zinc concentrate. One trial in particular was run over a three month timeframe and Fl gave improvements in recovery of 2.5% and a reduction in lead levels with less than 0.5% loss in grade. The dosages of other reagents in the flotation circuit were also reduced.Data demonstrating improved recovery and grade in lab trials will be discussed. Extensive data from the mill trial will illustrate how Fl works in both rougher and cleaner circuits."

Jan 1, 1990

By M. Harrison, C. H. Stockwell

"Metals vah1ed at more than $200,000,000 have been obtained, mainly since 1930, from the mines of northern Manitoba. The greater part of this production has been copper, zinc, and gold from the Flin Flon, Sherritt Gordon, and Mandy mines. The chief mines from which gold alone has been produced are God's Lake, Laguna, and Gurney. At present (May 1947) Flin Flon and Sherritt Gordon are the only producing mines, but the Nor-Acme property is being developed for large-scale production of gold. Large deposits of nickel and copper are being diamond drilled at Lynn Lake, and the Thompson, Ferro, and other properties are being developed. The mineral deposits lie within irregular or elongated areas of Precambrian sedimentary and volcanic rocks, surrounded by granite ( Fig. 1).The common rock types include basic and acidic flows, agglomerate, ruff, greywacke, arkose, argilli te, conglomerate, and their gneissoid and schistose derivatives. They are invaded by sills, dykes, and irregular bodies of gabbro and diorite, and all are cut by granite. Some of the sediments are interstratified with volcanics, and others are deposited unconformably on them.STRUCTURAL GEOLOGYLittle is known of the structures of the rocks in the area as a whole, because by far the greater part is unexplored or has been covered only by reconnaissance surveys. Available information indicates a general east structural trend in the southeast part, whereas in the west part the folding is mote complex with no definite overall trend. However, in a few small areas in the western part where detailed work has been done, as around the Flin Flon, Sherritt-Gordon, Nor-Acme, and other properties, the structure is fairly well known. The following descriptions apply chiefly to these areas ."

Jan 1, 1954

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By Dennis E. Bell

"This paper describes exploration and development to 1982 in the southern half of the northeastern British Columbia (Peace River or Northeast Block) inner foothills metallurgical coal belt. Gates Formation, Fort St. John Group, is the primary target; Gething Formation, Bullhead Group, is secondary. This part of the belt remains wilderness when compared to its other parts. Practical formational and structural mapping is described. A local problem known as the Secus Mountain or Mount Belcourt conglomerates is discussed. The three major explorers have been Denison Mines, PetroCanada, and Crows Nest Resources, all with partners. Initial mine construction and rail spur construction are continuing. The new town of Tumbler Ridge is being built. Introduction This paper describes exploration and development to 1982 in the southern half of the northeast British Columbia metallurgical coal belt. The area (Fig. 1) trends 120 km northwest from the Alberta border to the Wolverine River and Bullmoose Creek. The belt averages 15 km in width, and is 20 km at its widest. Physiographically, the area is dominated by rugged inner foothills, with relief to 1,500 m. The trend of the structures is transected by a dozen rivers flowing southwest to northeast away from the Continental Divide. The Rockies, lying immediately to the west, control the climate. One fact continues to colour all coal work in the area. When compared to the other parts of the western Canadian foothills and Rockies coking belt, it remains the least accessible and least mapped portion. Lack of access also makes all work expensive. Current activity centres about two mines in construction at the northwestern end of the area. Denison Mines and partners are developing their Quintette project, and Teck Corporation and partners are developing their Bullmoose project. PetroCanada and partners have intensively explored their Monkman-Duke Mounta,in project, but mine construction awaits better economic times. The rest of the area remains lightly explored, with the exception of some intensive work on particular structures by Denison and Petro-Canada. The focus of coal work has been metallurgical bituminous coal seams contained primarily in the Gates Formation (Fig. 2) and secondarily in the Gething Formation. These formations are found in generally en-echelon structures ranging to several kilometres in width."

Jan 1, 1985

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

By A. Rajan

"Drawing upon the experiences of a gold extraction plant startup in the Southern Pacific, this paper will describe the importance of the commissioning phases to the project outcomes to achieve early target production despite an overall time compression to attain full plant production. Some of the highlights of the paper include: impact of roles played by the Owner’s construction and operations representatives during project commissioning, the formation of a capable and competent “Mod Squad,” availability of trained operating personnel, control over work priorities and the scope of work needed to bring the plant to safe initial operations. The commissioning team comprised subject matter experts skilled in process technology supported by “generalists” thoroughly conversant in overall plant operations. The merits of a structured team approach to brainstorm and resolve commissioning challenges as opposed to direction from individual subject matter experts is discussed. IntroductionStartup or commissioning is a unique period in the life of a project. Each stage of a project-exploration, feasibility, design, construction, commissioning, initial operations and continuing operations-requires special talents, know-how, and practices. Each stage makes particular demands of the people involved. Initial operations are no exception.Having experienced the 1997 startup phases of oxide and sulfide facilities for a gold extraction plant at a remote island in the Southern Pacific, I can attest to the many challenges and rewards. Commissioning for both facilities was extremely successful and brought the entire project on line well ahead of the targeted completion dates. Using this specific project as an example, this paper will highlight some of the key features of project commissioning. In this paper, the term “pre-commissioning” denotes all activities that lead to mechanical completion; “commissioning” occurs when feed is introduced; and “initial operations” are defined as the duration when operations accepts the system/facility and takes over."

Jan 1, 2000

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By K. J. Fair, H. W. Smith, D. R. Francis, J. M. Toguri

"Bench-scale batch milling and screening tests were carried out on secondary aluminum dross 10 produce an aluminum concentrate. To complement these tests, an analysis of a commercial plant was also performed by sampling dross at various stages in the plant's milling and screening circuit. These studies have indicated that benefits of increased capacity, grade and recovery of aluminum metal can be realized by addition of screens before the ball mill, longer grinding period and by grinding the smaller size fractions more efficiently.To test the predictions, a plant test was performed on the milling of100tons of secondary dross. The recycling of the large size fraction (+1/8 in.) of aluminum dross through the impact mill rather than through the rate limiting ball mill resulted in a comparable aluminum grade. The ball milling of the _1/ 8 in. + 10 mesh size gave a dross grade of71% AI. A lower feed rate to the ball mill resulted in a higher final grade. With minor modifications, secondary dross can be processed in 22% of the time it takes with the present circuit without a sacrifice in grade.IntroductionSecondary aluminum dross is a mixture of metallic aluminum, aluminum oxides and salts (alkali halides). Any comminution process deforms or slowly grind s the malleable metal phase and reduces the size of the friable, brittle, oxide-salt phase relatively fasterr(1).The milling of aluminum dross is performed to upgrade the metallic aluminum fraction. Figure I shows a flowsheet for the milling of secondary dross as presently practised at Metals and Alloys Co. Ltd., Toronto, Ontario. At point A, large acceptable grade material is hand picked for refurnacing, the unacceptable off-grade material is sent to the sweat furnace and the remaining, + 2 in. fraction is recycled through the 3.9 ft by 4.1 ft impact mill. For simplification, three ball mills are shown. However, in reality there is only one, a 5 ft by 10 ft ball mill used in a semi-batch mode. The 2 in. + 3/8in. and 3/8 in. + 10 mesh products are remilled in the ball mill. The -10 mesh material is discarded as waste."

Jan 1, 1987

By Filipe Beretta

This study investigates geophysical logging capacity to predict coal quality. It was analyzed for possible correlation, some parameters determined via laboratory analysis of coal against results for the same parameter derived from wireline logs recorded by a geophysical probe. These probes detect variations in some rock physical properties, such as their natural gamma ray emissions and electrical resistivity. Results showed a strong correlation between natural gamma and ash content, establishing a linear model to estimate ash content from geophysical logging data with a low estimation error (less than 5%). Besides, results showed that there is no correlation between sulphur content or volatile matter and resistivity, neither with natural gamma of the rocks. Ash content derived from gamma ray values can be used as secondary information to evaluate coal quality during resources estimation, using methods such as soft indicator kriging. The methodology is illustrated using a case study at a coal deposit in south of Brazil.

Oct 1, 2009

By A. Bhowmik

Uranium Refining is the process in which undesirable neutron absorbing elements such as Boron (B), Gadolinium (Gd), Cadmium (Cd), Europium (Eu), Samarium (Sm) and other heavy metals (Fe, Ni, Co, Ca, Mg etc.) are removed to make it nuclear pure. At present, Uranium refining is carried out by solvent extraction process by using organic based solvent e, g. TBP diluted with Kerosene. The above process generates lot of nitrate bearing liquid waste and degraded organic. In order to eliminate use of hazardous organic and ammonia for Uranium refining altogether, a new process has been developed. In the new process, Yellow Cake is dissolved in nitric acid and uranium peroxide hydrate is precipitated selectively from the solution leaving all the impurities in the solution by using commercial grade hydrogen peroxide at a pre-defined pH, U conc., temperature and stoichiometric quantity of hydrogen peroxide under mild agitation. The precipitate is filtered and washed with DM water to obtain nuclear pure product meeting purity standard as per ASTM C ? 753-99.The product is spray dried and calcined to obtain uranium oxide. The process eliminates use of organic, flammable, toxic chemicals, consumes less quantity of nitric acid and uses environfriendly chemical hydrogen peroxide. The process is simple and can be integrated in the mill. A patent application is entering national phase in several countries including CANADA and abstract/full paper is available in WIPO publication no: WO/2009/013759.

Aug 1, 2010

By K. S. Kalenchuk

Massive landslides display complex deformation processes. For instance, slope movements of the Downie Slide, monitored using borehole inclinometers, extensometers, and survey monuments, show considerable spatial and temporal inconsistencies in the displacement rates. This study assesses the influence that inferred shear surface geometry, as a key factor contributing to variable slope movements, has on resolving spatially discriminated slope deformations in three-dimensions. Borehole data defines the shear surface location at discrete points within the slide and therefore, the shear surface geometry for the extent of the slide must be largely inferred. A series of three-dimensional numerical simulations have been run to assess the effect of different interpretations of the shear surface geometry. This investigation illustrates the importance of rigorous geospatial definition of slip surface geometry and the value of three dimensional modelling.

May 1, 2009

By M. P. Tibbs

An autonomous spray application system for a structural Thin Spray-on Liner (TSL) is targeting productivity and safety on underground coal continuous miners by potentially replacing steel mesh, and has broader applications as surface support and confinement in metalliferous mines and civil tunnelling. Polymer chemistry, coating formulation, geotechnical assessment and the autonomous application system are being developed as an integrated package as part of a continuous miner automation project. This polymer-based TSL system has significant benefits over conventional steel mesh skin confinement, including being more automatable by spray application, providing complete skin confinement and active skin reinforcement as a fast-curing composite with substrate, and having effective fire retardant properties for the polymer and the underlying coal. This paper presents a preliminary assessment of distance sensing systems that would enable autonomous adaptation of a nominal spray path to spray a consistent thickness of TSL (nominally 5mm) over an irregular topography. Two alternate sensors are assessed; firstly, a 2D LIDAR mounted on a linear axis is used to produce a 3D surface profile for generating an adapted spray path; and secondly, a robot end-effector-mounted ultrasonic sensor is assessed for wall following techniques to dynamically adapt a nominal spray path.

Aug 1, 2013

By Chris J. Pritchard

Pumpable, two-component resins for anchoring rock bolts provides significant advantages over traditional cartridge resin and cement grout systems where fast and easily adaptable support is required for difficult ground conditions. Cartridge resin anchoring with rock bolts is often ineffective in oversized, fractured and washed-out holes. Cement grouting of cable bolts is frequently plagued with QA and QC issues related to the grouting process. Installation of cable bolts with resin injection techniques is routinely completed in cycle allowing blasting immediately after cable bolting. Xstrata Nickel has evaluated the Minova Resin Injection System since 2007. The Nickel Rim Mine and partner Minova have tested and validated the Resin Injection process for bolting procedures including Hollow Fiberglass Bolts, Rebar, Modified Cone Bolts and Cable Bolts. The resin injection process is adaptable to most bolting processes and equipment. Currently, Nickel Rim Mine use 2 resin injection products with different set times to grout deep cable bolts and development support in highly variable ground conditions. The product predictability and adaptability in application along with a high crew acceptance continues to make this support process part of an adaptable ground support system. Product consistency and quality significantly reduce the quality control concerns for ground support in highly variable ground conditions.

May 1, 2011

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011

By Baoquan An

The energy required to fragment a rock is proportional to the increase in the fracture surface area and hence is proportional to the rock?s surface area. In comminution, the slope of the linear relationship between size reduction ratio and specific energy is usually defined as grindability. Another definition of grindability based on newly created specific surface area and specific energy is introduced. The two definitions for grindability reflect the grindability properties of rocks and can be used to measure of the efficiency of mills or crushers. The feed particle size distribution influences the energy needed to comminute the rock. For a given ratio of average feed size to product size, the smaller feed size requires more energy.

May 1, 2004

By P. W. Godbehere, B. W. Brooks

"This paper deals with the milling of slags from the Noranda Continuous Process, in the Horne Concentrator at Noranda, Quebec. The milling of copper slags, although novel in Canada, has been practiced in Japan, Finland and elsewhere for several years.In March 1973, the prototype Noranda Continuous Process furnace or ""reactor'' came on-stream, In this pyrometallurgical process (see Fig. 1), copper concentrates mixed with flux are smelted in a single furnace to form copper or a high grade copper matte, and slag. The conventional smelting processes of roasting, reverberatory smelting and converting have been incorporated in a single 17 ft. diameter by 70 ft. long steel cylindrical vessel (l, 2). The copper or matte is tapped from the bottom of the reactor into ladles and transferred to an anode furnace or to a converter. The slag is tapped into 40 ton capacity ladles, cooled, crushed, and conveyed to the concentrator. At the present time, the reactor is operated to produce matte. The matte slag* containing 4 - 6 per cent copper is milled using conventional ore dressing grinding and flotation equipment. A flotation concentrate assaying 35 - 40 per cent copper is recycled to the reactor. Crushing, conveying, grinding, flotation and tailing disposal equipment previously used for over 40 years for ore treatment has been modified to suit the requirements of slag milling. Slag milling is essentially the scavenger circuit of a pyrometallurgical process."

Jan 1, 1977

By S. K. Mitterecker, T. Hofbauer, F. Baerhold

"Acid regeneration is a very important process step in each acid leach circuit. It is required to recover dissolved metals and HCl from spent leaching acid. Andritz Metals presents its recently commissioned spray roast pilot plant. The facility is now available for testing and demonstrating acid recovery or metal oxide production which is a requirement in several flow sheets under development for the mining and specialized oxides industries. Results from pilot test campaigns are reported here. We are currently focusing on a nickel ore leaching process, which requires both a feasible iron control and acid regeneration step. In addition, we disclose the results of a magnesium ore and aluminium recycling test campaign conducted in our pilot plant facility.INTRODUCTION Hydrochloric acid regeneration is widely used in the steel industry to regenerate spent pickle liquors into hydrochloric acid at a typical concentration of 18 wt.%. Andritz Metals (formerly known as Ruthner) has built more than 200 acid regeneration plants worldwide (Andritz Metals brochure). As technology leaders Andritz also has vast experience with specialty metal oxide plants, producing metal oxides such as aluminium oxide (Al2O3), magnesium oxide (MgO), nickel oxide (NiO), cobalt oxide (Co3O4) and mixed oxides from metal chloride solutions (Baerhold F., Lebl A., Starcevic J., 2006), (Jedlicka, H., n.d.), (Ruthner M.J., Krischner H., 1973), (Ruthner Ind. Planungs AG, 1967). Hydrochloric acid leach circuits have been developed and proven in the industry for many years. Examples of industrial applications are: synthetic rutile production (TiO2) (Walpole E.A., Winter J.D., 2002), Quebec Iron and Titanium’s UGS process (Patoine M.-C., De Mori A., Borowiec K., Coscia C., 2002), magnesium and potassium production (Priemer H., 1973) and Goro Nickel (Vahed A., Colton D.F., Duterque J.P., Karner W., Baerhold F., 2004), (Taylor A., 2013). One of the critical process steps in developing a hydrometallurgical process is acid regeneration, as it is an economic requirement to recover both the dissolved metals and acid (commonly HCl) from the spent leaching solution."

Jan 1, 2016

By J. Lu, J. B. Wiskel, D. G. Ivey, E. Niemi, H. Henein

Simulated TMCP using a Gleeble was undertaken to evaluate the effect of the austenite to ferrite cooling rate, coiling temperatures of either 400°C or 500°C and the magnitude of plastic deformation at the coiling temperature on the hardness of a Grade 483 (X70) steel. For comparable apparent cooling rates and deformation conditions, the hardness of the samples were independent of coiling temperature The application of a minimum compressive deformation > 8% was required to increase hardness at both simulated coiling temperatures of 400°C and 500°C. An increase in hardness was also observed with increased cooling times between 800°C and 500°C (i.e., slower cooling rates).

Jan 1, 2005