Search Documents

By D. M. Hausen

"Refractoriness in Carlin-type gold ores results mostly from fine locking of gold in pyrite, locking in various gangue phases, notably quartz, and a ""preg robbing"" condition attributed to organic carbon. All three conditions may occur in any given deposit, including Newmont &apos;s Carlin and Gold Quarry deposits in Nevada, where types of ref ractoriness occur locally in minor amounts.Measurements of specific gravity, water absorption and screen size distributions of gold in alteration rock types from Gold Quarry show transitional changes from siliceous cherts through decreasingly silicified and increasingly argillized siltstones.Low permeability of siliceous ores contributes to ""size dependent"" refractoriness in cyanidation test work. Colligative physical and chemical measurements demonstrate that silicified cherty ores are difficult to grind, poorly permeable, and less amenable to cyanidation. Refractoriness in pad or column leaching of coarsely crushed siliceous siltstones and cherts is shown to correlate with interrelated measurable mineralogic and physical parameters.IntroductionMetallurgical treatment of variably amenable and refractory types of gold ore may be guided by both analytical and mineralogic data on the interlocking of gold (microscopic an d sub- microscopic) in assorted gangue/sulphide phases. Most oxidized ores from the Carlin gold mine, north of Carlin, Nevada, are amenable to direct cyanidation. The permeability of most oxidized ores from Carlin coupled with the fine size of the gold < 1.5 um) yields rapid extractions and high recovery without fine grinding.Small portions of the Carlin ore body, and also the nearby Maggie Creek and Gold Quarry orebodies, are less amenable to cyanidation, and are classified as refractory. Refractory conditions may be attributed mostly to the association or interlocking of gold with pyrite and /or microcrystalline quartz or chert, and also by the adsorption of leached gold by deleterious forms of carbon, termed ""preg-robbing"" carbon. Each of these conditions are described and defined, with emphasis on a form of silica-locking, which has been referred to as "" size dependent"" refractoriness."

Jan 1, 1985

By Julie Hunt

Rimfire Minerals Corporation: early stage precious metal exploration specialists with discovery opportunities in partnership with major and mid-tier gold producers or prominent junior exploration firms. Mike Roberts, Senior Geologist

May 1, 2006

By Brad Ross

? Value in number of children ? Polygamy common ? Support of extended family and friends ? HIV/AIDS ? Not a culture of savings ? Minimal mechanical experience ? Supportive ? Unintended hindrance ? Mining claims ? Export Permits Lack of funding

May 1, 2011

By J. M. D. Wilson, W. Petruk, C. Coté

"The behaviour of minerals in the Mount Wright spiral circuit was investigated to find methods of improving iron oxide mineral liberation and recovery. The feeds, concentrates and tailings from rougher, cleaner and recleaner spirals in one mill line were sampled before and after the sizing screen openings were reduced from 2 mm to 1.6 mm. Sized fractions of each sample were analyzed with the MP-SEM-IPS image analysis system at CANMET to determine mineral quantities and liberation characteristics of the iron oxide minerals. Mass balance techniques were used to calculate stream recoveries of iron, silica, total iron oxide minerals, hema¬tite, goethite, quartz, ferromagnesian silicates, and liberated and locked total iron oxide minerals for each sieve fraction.The reduction of the sizing screen openings increased the ap¬parent liberation of the total iron oxide minerals in the screen undersize from 89% to 94% and raised the over-all iron recovery from 84.4% to 85.3%. Apparent liberation of iron oxide minerals in the cleaner sand also increased from 70% to 85%, but the – 75 µm fraction re¬mained the only fraction containing an acceptable amount of liber¬ated iron oxide minerals in each case. Due to limitations of spiral and grinding efficiency it is recommended that the cleaner sand be screened at 300 m, the +300 m fraction be reground, and the – 300 p.m fraction be rerouted to the rougher spirals.The amount of fine liberated iron oxide minerals (– 106 m) lost in the tailings was 46 TPH in mill line 3. This value represents 41 wt % of the free fine iron oxide minerals, or 7 wt % of the total iron oxide minerals in the spiral feed. Further work is needed to investigate the possibility of recovering this material by other methods.Middling iron particles (010 50%) and presumably free gangue in the size range –300+ 75 m tend to be recovered by spirals by entrapment."

Jan 1, 1990

By W. Petruk, D. R. Morris

"The lead concentrate produced from the volcanogenic base metal ore of Brunswick Mining and Smelting in New Brunswick contains major to trace amounts of iron, zinc, cadmium, arsenic, antimony, copper, silver, selenium, tellurium, bismuth, sulphur, tin, indium, mercury and manganese as impurities. When the concentrate is sintered some of these impurities enter a variety of oxide phases, whereas others precipitate as metals. In the lead blast furnace the oxide phases decompose and the impurities recombine 10 form new phases, most are eventually discharged to the slag. The metals of the sinter remain as metals in the lead blast furnace where even more are produced, and are discharged largely with the lead bullion,IntroductionMany lead concentrates are produced from volcanogenic base metal ores . Such ores contain a wide variety of trace minerals and trace elements , therefore, concentrate s obtained from them will contain the trace elements as impurities . The impurities in the lead concentrate from one such ore, the Brunswick No. 12 deposit of Brunswick Mining and Smelting Corporation (BM S) in the Bathurst area in New Brunswick , were studied as pan of a larger investigation that was conducted to determine the extent of chemical reactions of the sinter within the lead blast furnace(1,2) The lead concentrate was investigated to identify the host mineral s for the impurities, the lead sinter was studied to identify the host phases, and frozen products from different depths within the BMS blast furnace at Belledune, New Brunswick were studied to determine the behaviour of the impurities.T he investigation was performed by pre pa ring polished sections o f the samples and studying them with a reflecting microscope, a scanning electron microscope (SE M) equipped with a Kevex energy dispersive X-ra y analysis system, a microprobe, and a Quantimet 720 image analyzer. The samples were also analyzed by X-ray diffractometer, and individual grains were analyzed by the Debye-Scherrer X-ray powder film method."

Jan 1, 1985

By L. Contretras

This study has as an objective to analyze and to propose actions to improve the quantity and quality of the graduate education in the area of mining industry, specifically of mining engineers, metallurgists, geologists, to satisfy the expectations of professionals in the mining industry. Included are an analysis of the present scenario and the future demands in countries like Chile and proposed plans for the Establishment of Educational Initiatives, country policies and market forecast, vis-a-vis the experience of Australia, South Africa, United Kingdom, Canada and the United States of America.

Jan 1, 2007

By Jean A. Bastien

Cette présentation décrit les étapes de développement et l?exploitation souterraine au puits Penna chez Agnico-Eagle division Laronde. Les sujets suivants sont touchés : le fonçage du puits, le développement des niveaux, la méthode d?exploitation, la manutention de la roche brisée, le méthode de remblayage et la ventilation. En résumé : le fonçage du puits s?est fait sur 2,240 mètres de novembre 1995 à mars 2000. Le développement des niveaux a débuté en octobre 1998. Les opérations de minage ont débutés en août 99 dans le premier horizon situé au dessus du niveau 122. Les chantiers sont exploités par longs-trous d?environ 25 mètres de long avec un diamètre de 10 cm. Les accès à la zone minéralisée sont transverses. Le minerai est soutiré des chantiers et acheminé au passe-minerai a l?aide de chargeuses navettes. Par la suite, le minerai passe sur un marteau, est concassé et transporté sur un convoyeur, jusqu?au silo de 4,500 tonnes au-dessus de la station de chargement automatisée du niveau 152 d?ou les skips sont alimentés. Le remblai en pâte est envoyé de la surface par des trous ayant un revêtement d?acier. Le diamètre intérieur est de 15 cm. Le réseau de ventilation est principalement alimentée par des ventilateurs de surface (système aspirant et souflant) conçus pour acheminer sous-terre un maximum de 640 mètres cubes par minutes (1,350,000 pcm).

May 1, 2001

By Enrique Rubio

Several mining operations are currently evaluating the feasibility of changing their mining method to Block Caving. There will also be several deep low-grade ore bodies that will face the need to go underground in following their ore to depth. There are two main reasons why Block Caving is attractive: firstly, it offers the lowest operating costs amongst all the mining methods; and secondly, it is truly a massive mining method, offering the highest potential production capacity. Despite its longstanding popularity, there are still significant components of the method that are not clearly understood. Also, the lack of availability of key geomechanic information still presents a major obstacle to developing mine planning and production scheduling. There are several key issues in block caving that can make it feasible such as cavability, fragmentation, stresses will condition the way that a block caves and the way that material is drawn from the draw points. Consequently Block Cave mining method is a good example where the ore body has to be related to design and mine planning. The concepts of dilution, draw control as well as sequence definition are reviewed in this paper to illustrate the idea of integration. There have been some examples of mines where some of the components of mine planning have not been integrated causing a disaster in terms of economics or safety. Different layouts configurations might give a different result in the planning of the mine

May 1, 2002

By Carl Faessler

Abstract Some Canadian geologists believe chat, in the Grenville sub-province of Eastern Canada, there is no granitic intrusion older than the anorthosite. The writers are among those who hold the contrary view. They suggest a new means to distinguish between rocks belonging to intrusions respectively older (Laurentian) or younger (Pine Hill) than the anorthosite. This new method is based on microscopical observations which demonstrate that the Pine Hill intrusives contain a large amount of exsolution perthite, whereas the Laurentian intrusives are completely devoid of exsolution perthite. Where perthite is present in Laurentian rocks, it is the result of lacer hydrothermal replacement. Introduction The present paper is the result of a systematic study of some acidic intrusive rocks in the Grenville sub-province. These rocks underlie large areas of the Canadian shield in the Province of Quebec, mostly along the southern border of the shield.

Jan 1, 1946

By Peter N. Calder, Garston Blackwell

"The history and analysis of a structurally complex open-pit rock slope displacement are described. The failure involved part of the only haulage access to a major ore zone. The ongoing movement was monitored using an electronic distance measuring device and a continuous electronic system specifically designed for the problem. A major fault, infilled with a thick clay gouge, and intersected by other structural features, resulted in the transfer of weight to a rock mass acting as a buttress in the lower regions. Movements were affected by blasting vibrations and ground-water conditions. Remedial measures included limiting blasting levels and lowering the water table, following which mining was successfully resumed in the area.IntroductionBrenda Mines is situated in a mountainous region of the southern interior of British Columbia; the location is indicated on Figure 1 . The elevation is approximately 5000 ft , giving a climate typical of more northern areas. Temperatures vary from -30°C to + 30°C. A snowfall level of 400-800 cm is experienced from November to April. During the spring, a heavy runoff period occurs, increasing the pumping rate in the pit from a nominal 50* gal/min to 2000 gal/min.The orebody occurs in a fractured Jurassic rock mass referred to as the Brenda Stock; it is approximately 3000 ft in diameter and 1000 ft deep. The Brenda Stock was intruded into the Upper Triassic Nicola Group tuffs, breccias and argillites. Mineralization occurred in several stages in a relatively homogeneous quartz diorite host rock. Shearing, faulting and jointing occured later in many stages, producing mineralized clay gouge zones up to several feet in thickness&apos;> , These gouge zones have a major effect on the stability of the pit walls.The structural geology of the pit walls is otherwise relatively simple. Figure 2 is a conventional pole diagram indicating the orientation of the rock structural systems which are present. The major system has an average dip of approximately 70 degrees to the south and strikes approximately east /west , it is not undercu t by the pit slope. Figure 3 is a photograph of part of the North wall on which this system is indicated.The basic pit design consists of a working bench height of 50 ft, with a final wall height of 100 ft between berm s and a 100-ft-wide berm every second lift. Combined with a local face slope of 50-70 degrees, the resulting wall slope, not including haulage roads, is 45 degrees. Figures 4 and 5 are generalized plans and sectional views of the pit."

Jan 1, 1980

By Alan J. Wianwright

Introduction ??New world-class Upper Devonian porphyry Cu-Au system located in south Mongolia ??6.5 km NNE-trending mineralized corridor ? 4 discrete deposits ??Southern Oyu deposits: Chalcopyrite, deposits: bornite ??Hugo Dummett: Zone: Hypogene chalcocite in addition to chalcopyrite and bornite ??Total resource exceeds ~2 Gt@ >1% Cu, >0.25 g/t Au (0.6% Cu equivalent cut-off) (Ivanhoe Mines press release, 2005)

May 1, 2006

By L. E. Young

"The Red Dog deposit of the western Brooks Range, Alaska was discovered in the 1970s. Two mineralized areas are present, the Main and Hilltop deposits. With indicated and inferred reserves of 77 million tonnes of 17.1% zinc, 5.0% lead and 82 g/ tonne silver, the Main deposit of Red Dog represents one of the world&apos;s largest zinc-lead deposit s. Since serious evaluation by Cominco commenced in 1980, a better understanding of deposit geology has been gained through 10 715m of diamond drilling and concurrent geologic, geophysical and geotechnical studies. The Red Dog deposit is of Mississippian to Pennsylvanian or Early Permian age, and straddles a redox transition in fine-grained and chemical sediments of the Red Dog structural sequence.The Main deposit has been modified by regional Mesozoic thrust faulting and isoclinal folding, resulting in complex interrelationships between silica rock, sulphide rock and barite. Multiple lines of evidence suggest the Main deposit contains both a syngenetic stratiform and a replacement component. Ore fluids were probably derived by regional lateral movement of brines through a coarse clastic footwall aquifer, then upwards along block faults to the site of the Red Dog deposit.Historical PerspectiveThe region in the vicinity of the Red Dog deposit (Fig. 1) was first prospected by J. W. Kelley in the late 1880s (Orth, 1967). The first coordinated inland exploration was conducted by the U.S. Geological Survey in 1910-1911 and 1923-1926 (Smith, 1913; Smith and Mertie, 1930). The earliest reports of zinc-lead mineralization in the region include reference to samples collected at unknown locales by Eskimo prospectors (Anderson, 1944). In 1955 stratiform pyrite was discovered 19 km west of Red Dog by I.L. Tailleur of the U.S. Geological Survey (Tailleur, 1970). The first reported visit to what is known as Red Dog was by I.L. Tailleur in 1968, who was field checking a colour anomaly noted by B. Baker, a local bush pilot (Tailleur, 1970; Moore et al., 1986) ."

Jan 1, 1989

By M. Hall

"SomarioEl circuito de molienda a Selbaie consta de molino semiaut6geno en un circuito cerrado y molino de balas en un circuito cerrado. El amperaje del motor de se usa controlar el tonelaje el molino. Este sistema estabiliza el circuito pero no mejora activamente el rendirniento del circuito. Se desarroll6 auxiliar el rendimiento del circuito un sistema experto en manipular las objetivos de existir control proporcional-integral. Se ejecut6 el sistema con el Comdale /C conjunto del sistema experto y ha side funcional hace tiempo el mayo de 1992. El sistema experto ha resultado en un aumento en tonelaje de 7tph y una disminuci6n de $210,000 en el caste anual de media de molienda. Se describe el desarrollo del sistema y los provechos derivar se presenta.AbstractThe grinding circuit at Selbaie consists of SAG mill and ball mill closed circuit grinding. The SAG mill motor current is used to control throughput. This system stabilizes the circuit but does not actively optimize circuit performance. An expert system was developed to aid the optimization of the circuit by manipulating the set-points of existing PI control loops. The system was implemented with the Comdale /C expert system package and has been on line since May 1992. The expert system has resulted in a net increase in tonnage of 7tph and a decrease in annual grinding media costs of $210,000. The system development is described and the benefits derived are presented."

Jan 1, 1994

By A. J. Smethurst, S. B. Hearn, S. Boskovic

"The problem of crud in solvent extraction is well known and can be a major handicap and operational issue. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Flocculation can be utilized to remove some of the troublesome particulates but colloidal silica does not flocculate well and presents a different problem requiring innovative chemistry to solve. Coagulants can assist by facilitating the removal of this colloidal silica by promoting the agglomeration of the particles to a size which can be more readily settled or flocculated in solid/liquid separations. This is achieved when the coagulants bind to the surfaces, displacing water and destabilizing the colloids, whereupon they bind to each other which facilitate their amenability to conventional flocculation.INTRODUCTIONSilicate minerals are abundant in the upper layers of the Earth’s crust, and there are few mineral deposits without significant levels of gangue silicates. Silicate minerals include the pure silicas, such as quartz and other silicate containing minerals such as clays, chlorites, feldspars, as well a vast number of less common silicates.During the acid leaching of ores, two types of fine silica particles are released in solution from the dissolution of the host mineral. The first consists of partly depleted silicates, and the second is colloidal silica, which forms in solution. It is this second type which has the potential to cause crud formation as well as poor solution clarities, slow filter rates and excessive flocculant usage (Figure1)."

Jan 1, 2016

By F. J. Munn

"Since 1976, Cardinal River Coal s Ltd. has completed mining in eight pits. In each of these pits, at least one wall has failed, none by design, although not totally unexpected, yet there was no loss of production nor risk to personnel or equipment. Cardinal River Coals Ltd. has been successful in implementing a program to cope with failures and now feels justified in adopting more optimistic design parameters.The wall control program at Cardinal River Coals Ltd. is based on the premise that the walls are going to fail, monitoring is to confirm when. The program consists of monitoring slope movements and piezometric levels as well as structural mapping and visual inspections. In case of excessive movement, the frequency and intensity of the monitoring is increased. If a failure is impending, suitable remedial action is undertaken such as cutting down the crest, building up the toe, depressurization of the wall, artificial support, or a combination of the above. If remedial action is not possible, monitoring permits operations to continue up to near the time of failure.At the design stage, the emphasis is on identifying the potential failure mechanisms and the con sequences of failure. Once the potential failure mechanisms are identified, a monitoring system can usually be employed to give sufficient response time, and providing the consequence of failure is not severe and/ or remedial action can be taken to arrest the movements, then it is practical to mine pit slope s which have a higher probability of failure."

Jan 1, 1985

Overview of Presentation ?About MiHR ?Human Resources Challenges in the Minerals and Metals Industry ?Getting the Facts -Sector Study Project ?Key Findings ?Recommendations ?Conclusions ?MiHR?srole

May 1, 2006

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By Corby G. Anderson, Caelen D. Anderson, Patrick R. Taylor

"The United States contains a variety of domestic rare earth element mineral sources containing such as ancylite, bastnasite, monazite, and xenotime. Research has been performed to investigate the fundamental surface chemistry involved in the froth flotation of these minerals, and apply the knowledge gained to substantiate the results through experimental testwork on a domestically sourced rare earth ore. This paper will outline the fundamentals and literature of rare earth mineral flotation, review its industrial applications and provide some recent research updates.THE RARE EARTH ELEMENTSRare earth elements (REE’s) are a unique family of elements with nearly identical physical and chemical properties. They account for approximately 1/6th of all naturally occurring elements, but the entire group occupies only one position on the periodic table. These 15 elements make up the lanthanide series (atomic numbers 57–71), and all but one (promethium) occur naturally. In addition to these 15 elements, yttrium and scandium are also considered rare earths since they tend to occur in the same deposits as the rare earths and share similar physical and chemical properties as seen in Figure 1. In particular Figure 2 denotes, a cartoon of the subtle differences in each caused by the 4f atomic sub shell (Gschneidner Jr., 1964). These subtle differences result in very difficult challenges in the selective concentration and final separation of each rare earth. (Anderson, 2015, Kronholm, Anderson, Taylor, 2013)Rare earths are separated into two different subsections; the “lights” or LREE’s (lanthanum57 through europium63) and the “heavies” or HREE’s (gadolinium64 through lutetium71). Yttrium is generally considered a heavy rare earth since its ionic radius is close to that of the HREE’s, while scandium is not considered either a light or a heavy."

Jan 1, 2016

By T. T. Ni

FOR MORE THAN 200 years, the Kochiu district of Yunnan province has been, and it still is, the hub of China&apos;s tin industry. The district produces annually from 80 to 90 per cent of that country&apos;s out-put of tin, which averages about 9,300 tons a year and places China fifth among the tin producing nations of the world. The tin ore reserves of the country are estimated (1) at 1,873,370 metric tons, of which 1,500,000 tons are in the Kochiu district. The mill of the Yunnan Consolidated Tin Corporation, described in this paper, is the only one of its kind in China. MINING AND SMELTING There are only two tin mines in the Kochiu district operating with modern equipment -the Hsin-Chang and the Lao-Chang, both owned by the Yunnan Consolidated Tin Corporation, a government company. The Hsin-Chang mine has four working levels with cross-cuts 6 ft. by 6 ft. and is equipped with steel mine cars and trucks to haul the ore. The ore is hoisted to surface in a three-compartment shaft and transferred to the mill by a 4-kilometer aerial tram. The Lao-Chang mine has two circular shafts 656 feet apart, each equipped with two cages. Haulage-ways 1,600 meters and 1,000 meters long, respectively, have been driven to the southwest from these shafts and are connected by three cross-cuts.

Jan 1, 1951

By A. D. Mufch, G. P. Mitchell

"THE HARDY MINE of Falconbridge Nickel Mines Limited is located in Lot 9, Concession 1, Levack Township, Sudbury District, Ontario, 20 miles northwest of the city of Sudbury, and a mile west of the town of Levack. The ore deposit is one of the many nickel-copper sulphide bodies found on, or near, the lower contact of the well-known Sudbury norite-micropegmatite irruptive, and is one of a family of ore deposits which occur on the northwest rim of the irruptive.The property was acquired by purchase in 1935. In the same year a magnetometer survey along the footwall contact of the norite, which is covered by about 150 feet of glacial sands and clays, first indicated the location of the orebody. Drilling from 1935 to 1942 outlined the extent of the ore. Shaft sinking was commenced in the fall of 1951, and the mine is now approaching full production at a rate of about 300,000 tons per year.There are several major differences between the geology of the Levack area and the Falcon bridge area, which lies at the opposite extremity of the irruptive, 28 miles to the east. The purpose of this paper is to describe the essential features of the geology of the Levack area as seen in the Hardy mine, and to supplement the recent papers on other properties in the Sudbury area by Davidson (1), Lochhead (2), and Yates (3).General GeologyA recent review of the regional geology and an extensive bibliography of the Sudbury area can be found in the two papers by H. C. Cooke (4, 5). Some of the recent related references are: Jas. E. Thomson (6), E. M. Abraham (7), Franc. R. Joubin (8), W. G. Q. Johnstone (9)."

Jan 1, 1949