Search Documents

Over the years, efficient on-line monitoring of performance and status of an electrolytic copper refining process has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Recent innovative developments by Kennecott Utah Copper Corporation and Outokumpu Technology in wireless cell voltage and individual cell temperature sensing opens new possibilities to improve and modernize tank house management. This paper describes the powerful Outokumpu CellSenseTM refinery monitoring system for efficient interpretation of data produced by wireless CellSensorTM system with traditional refinery measurements. Examples from commercial tank house installations demonstrate the benefits of the system to improved process control and operation. The Outokumpu CellSenseTM monitoring system is simple to operate and accessible to all the plant operation teams.

Jan 1, 2007

By G. B. Harris

A process for the recovery of copper from the waste oxide copper of a mined-out sulphide orebody is described. Hydrometallurgical recovery of copper from this and similar wastes has been tried several times previously without success. Leaching is carried out by sulphuric acid in columns under conditions that minimise the iron content of the pregnant leach liquor, and copper is then recovered by ion exchange rather than the more conventional solvent extraction. The resin is stripped by spent electrolyte and copper is electrowon. Results are presented for testwork originally carried out in 1993, and repeated in 2006, and the novel aspects of the process, leaching and ion exchange, are discussed. Finally, preliminary order of magnitude capital and operating costs are given, demonstrating that the process is cost effective.

Jan 1, 2007

By Blandine Arseneault

The Raglan Mill had been in production for less than a year when the initial toxicity tests on the effluent revealed that it was defined as ?toxic? under regulations. Testwork was begun to address the fundamental reasons for the toxicity and a systematic approach was initiated to identify causes. Elimination of the problem presented a challenge once the main conclusion identified high dissolved solids as the principal culprit. In particular, normally benign soda ash (sodium bicarbonate) reagent additions used in milling, was identified as the main contributor to the problem. Following analysis of all requirements and safety considerations, a concept to recycle 100% of the mill process water was pursued. In addition to meeting regulatory requirements, this project would have numerous positive benefits to the operation, including reducing fresh water consumption and lowering costs.

Nov 1, 2002

By K. Shitogiden, Y. Samada, T. Miki

Steelmaking slag contains nutrition such as Si, P and Fe for acceleration of phytoplankton growth. Phytoplankton can fixate carbon dioxide more than any other species on earth. Hence, suppression of CO2 can be achieved by applying the potential of steelmaking slag as the nutrition for their propagation. When it is considered to supply nutrition from steelmaking slag to seawater, we must avoid dissolution of hazardous elements or change of pH of seawater by steelmaking slag addition into seawater. The protection against dissolution of fluorine into artificial seawater has been studied based on dissolution behavior of steelmaking slag and synthesized substances into artificial seawater in the present work. The dissolution mechanism of fluorine from steelmaking slag and buffering action of pH change are discussed by using stability diagram in seawater.

Jan 1, 2004

By S. Xu, A. Ramesh, F El-dabbagh, Z. Fang, A. Sobhy, J. A. Kozinski

Waste remediation is a goal that will be driven forward by economic conditions. As the cost of waste disposal increases, new methods of waste reduction will become economically attractive, and will be implemented. It is difficult to imagine, however, a time when there will be no waste generation. For the foreseeable future, despite effective reduction practices, there will still be hundreds of millions of tons of waste that must be destroyed or controlled to protect the public health and the sanctity of the environment. To remain faithful to environmental covenants, the mineral and metallurgical industries will face these new challenges. This paper discusses novel waste remediation approaches and techniques focusing on hazardous wastes and thermal remediation. Aspects concerning technological and environmental importance are examined. Solutions for neutralization of environmentally hazardous compounds are proposed.

Jan 1, 2004

Abstract-This paper discusses the fundamental question, "what is an adequate sample size?" in the light of recent developments regarding parameters of Gy’s well-known formula for predicting sampling variance. New understanding of the granulometric factor, g, and the liberation factor, l, had significant impact on the results of calculations involving Gy’s equation. For the granulometric factor, justifications are given as to why nominal comminution size should always be reported as P95 (i.e., the screen size rejecting 95% of the mass). A small but important change in the model to estimate the liberation factor makes the difference between a predictive formula that works or does not. Other parameters and considerations regarding their practical implementation are commented upon in light of the author’s experience.

Jan 1, 1998

By A. E. Reschke

Optimized mine planning of the Leeville Gold Mine, Nevada, necessitated the requirement for an average of 2540 tpd of high quality cemented rockfill (CRF) in primary stoping blocks and underhand cut and fill workings. To meet this requirement, a number of innovative design features were incorporated into the overall batching plant design. Foremost is the use of a dedicated skip to transfer crushed aggregate from surface down through the ventilation shaft to twin underground storage silos. Also, the use of a high shear colloidal mixer on surface to pre-slurry a cement/flyash binder with pipeline delivery to one of two separate underground CRF mixing stations was incorporated. Finally, the binder and aggregate are combined in a 9 m3 twin shaft compulsory type mixer before loading into teleram trucks for placement.

May 1, 2007

The following briefing is intended to provide an overview of the present and future challenges associated with our access to a secure and adequate supply of electrical energy necessary to support safe, productive and sustainable mining initiatives at Musselwhite. Contents ??Site power demand vs. current available supply ??Supply technical deficiencies ?adequacy and security of present supply ??Present internal generation ??Anticipated future internal generation requirements ??Increased requirements necessary for planned expansion ?demand/security ??Goldcorp?s strategy to achieve required supply ?transmission line initiative ??Subsequent benefits to others from the Goldcorp initiative. ??Economic impact of MusselwhiteMine on the northwest region ??Anticipated economic impact of planned expansion ??Expected life cycle of MusselwhiteMine ??Comparative energy costs for similar operations in other jurisdictions ??Conclusions ??Anticipated action plan ??Energy Management Initiatives ??Site Orientation

May 1, 2009

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

By David J. McDougall

"The production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with Les Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivieres (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about Les Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian milieu, but whatever the reason, the other Quebec iron works have been generally ignored. All but one of the Quebec blast furnaces could be described as ""pre-industrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day. Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence River. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces. Five of these, including Les Forges du St. Maurice, were located on or near the St. Maurice River which enters the St. Lawrence River from the north, and two, the St. Francis Forges and the Grantham Iron works were on or near the St. Francis River which enters the St. Lawrence from the south. In a general way deposits of bog iron ore in the St. Lawrence lowlands of Quebec were contained within the limits of the post-glacial Champlain Sea, with many clustered along the flanks of the St. Narcisse recessional moraine which is crossed by the St. Maurice and other near-by streams, and the Drummondville recessional moraine which is crossed by the St. Francis River."

Jan 1, 1999

By Patricia J. Dillon

Established in 1997, Prospectors and Developers Association of Canada Mining Matters (PDACMM) is a registered charitable organization dedicated to providing Earth Science education to grade school students. Through the development and distribution of educational programs and materials, PDACMM informs students of Canada?s geology and mineral resources as well as promoting awareness of the importance of rocks, minerals, metals and the mining industry. PDACMM also co-ordinates with other charitable organizations and government agencies to provide support or to work in tandem with them and reach as many young people as possible. Although PDACMM became a charitable organization in 1997, it actually has its? roots in 1994 when the Grade 7 program Mining Matters/Une Mine de Renseignments was developed to help teachers bring geology and mining into the classroom. Over 2100 of these resource kits were distributed to teachers across Ontario during the period 1995 to 1998. This unit won national recognition when it received the prestigious Partnership Focus award from the Conference Board of Canada for ?promoting science literacy for the world of work?. Due to the phenomenal success of these kits, a Grade 4 kit entitled Deeper and Deeper/Aller au Fond Des Choses was developed in 1998 in response to the opportunity provided by the new Ontario curriculum released at that time. Over 2600 of these kits were distributed throughout Ontario and there is a substantial waiting list of teachers hoping PDACMM will be able to raise enough money for another print run.

May 1, 2002

The Boleo project is located in Mexico close to the town of Santa Rosalia on the Baja Peninsula. The Boleo deposit contains copper, cobalt, zinc and manganese values as oxides with minor sulfides. The Boleo deposit is metallurgically challenging due to: 1) the requirement to recover four separate metals; 2) the presence of high levels of clay in the deposit resulting in difficult solid-liquid separations, and; 3) the need to use seawater for the bulk of the processing. Baja Mining, Bateman Engineering and SGS Lakefield Research have collaborated to develop and test a process flowsheet to recover copper, cobalt, zinc and manganese products at Boleo. The key steps in the flowsheet are: ? Feed preparation (scrubbing and ball milling of oversize) in copper raffinate ? Ore leaching using oxidative and reductive leaching ? CCD washing using high rate thickening technology ? Copper SXlEW ? Treatment of a bleed solution for cobalt, zinc and manganese recovery The process for cobalt, zinc and manganese recovery involves iron and aluminum removal followed by cobalt/zinc bulk extraction using CSIRO's DSX solvent extraction system and selective zinc and cobalt stripping. The zinc strip solution is evaporated to produce zinc sulfate monohydrate crystals to market and cobalt is recovered via a further SXlEW process as high purity metal. Manganese is precipitated as manganese carbonate from the DSX raffinate solution. This paper will review the Boleo process flowsheet and provide detailed results from the 2006 pilot plant operation conducted at SGS Lakefield in Canada.

Jan 1, 2007

By A. A. Sirkeci, M. Tarkan, N. Acarkan, O. Kangal, G. Bulut

This investigation deals with the evaluation of the tailings of the Kirka Borax Plants. In this respect boron in the tailings was recovered and the utilization of the clayish fraction was investigated. There are five tailings ponds in Kirka four of which are used for the tailings of the borax concentrator and the remaining one is used for the tailings of the sodium penta-borax plant. Experiments were conducted with samples taken from ponds containing coarse fraction and fine fraction. Coarse fraction of Borax Concentrator were screened through a set of sieves. The fraction above 1 mm was removed with 41.5% recovery and 33.3% B203 content. Scrubbing was applied above 0.1 mm and products containing 32 to 34% B203 were obtained with recoveries around 35%. The tailings of sodium penta borax plant was also screened and it was found that 15% of boron reported to +1 mm size fraction with 35% B203 content. Sample containing fine tailings was treated by cycloning. The cyclone overflow was found to be below 6µm and it was separated to be used in the subsequent tests. The usage of cyclone overflow in paper, ceramics, glass, pigment and drilling industries was investigated. Since this fraction is mainly composed of carbonate minerals rather than clay minerals it was suggested that it may be used for construction and moulding purposes. Furthermore, the B203 content of the cyclone overflow was reduced to 2.4%.

Jan 1, 2004

By Alex Henderson

The underground hard rock mining industry has had little change since the mobile equipment era began in the 1970s. Equipment has become larger and faster but has not kept pace with the following challenges: ? Improvements in safe production, ? Increasing demand for metals, ? Environmental improvements, ? Decreasing grades, ? Increasing depth of mining, ? More metal from underground vs. surface mining, and ? Energy and green house gas awareness. We are on the cusp of a new mining era and must rethink how underground hard rock mining must change in order to meet these challenges. This paper will show historical changes and propose a set of guiding principles for the next era of mining. Mining has changed over the last century. Initially mining was primarily an endeavor carried on by private companies with minor environmental controls and few social expectations other than employment. In the mid to later part of the century the mining industry was facing new challenges: deeper mines, the London Metals Exchange markets for pricing, and environmental concerns related to acidic rock drainage coming to the forefront. In today?s context, mining has evolved in complexity with the social and environmental aspects equally or surpassing the technical complexities such as expanding from mining hard rock to laterites, and mining lower grades or at greater depths. Nowadays, communities must be considered as partners, both locally and globally and the increased international visibility pushes the mining sector to take a more balanced approach to the business of mining (Fig. 1).

May 1, 2011

By W. J. Witte, M. K. Witte

"INTRODUCTION A pilot heap leach project was conducted on the B. P. Selco Hope Brook ore located in southwestern Newfoundland. The pilot heap leach was undertaken to assess and confirm the following:1) To confirm that heap leach technology now currently used in the United States could be applicable to Canadian sites.2) To confirm gold recovery by the Heap Leach technology3) To assess and study potential heap leach environmental concerns in cold and wet climate.PROJECT LOCATIONThe Hope Brook Project is located near the southern coast of the island of Newfoundland, approximately 100 kilometers southeast from Stephenville, approximately 25 kilometers west of Burgeo, Newfoundland. Access to the property is limited to helicopter, float plane or by sea through Couteau Bay. The property was covered with muskeg and very few trees. Surface relief was moderate with many poorly drained boggy sections confined to small areas. Many small unnamed lakes were located on the property which provided water to small brooks and streams flowing to Couteau Bay.Several locations were reviewed for the installation of the pilot heap leach facility. Important parameters used to select a suitable location included sufficient land area, close proximity to but not on the ore body, reasonable protection from wind, sufficient supply of fresh water, close to a suitable location for a portable crushing plant, reasonable access to aggregate material for preparation of the test pad and ponds and suitable contours to minimize site preparation."

Jan 1, 1987

By Robert B. Parsons

"The Whitehorse Mining Initiative (WMI) brought together all of the key stakeholders in Canada's mining industry to develop a framework whereby the industry can meet the challenges that it faces into the 21st century. The WMI Accord7 which was signed at the annual Mines Ministers Conference in Victoria, British Columbia, on September 137 1994, touches all of the important issues that confront the industry, including taxation. IntroductionSeptember 13, 1994, was a historical day for Canada's mining industry. On that day, on the occasion of the annual Mines Ministers Conference in Victoria, British Columbia, the Whitehorse Mining Initiative (WMI) Accord was signed by the leaders of the five principal stakeholders in the industry: industry; government; labour; environmentalists; and aboriginals. The Accord is the culmination of two years of hard work and intense collaboration by these stakeholders. But, the Accord is not the end result. The Accord can better be described as a springboard to a prosperous future for mining in Canada.The WMI had its beginnings at the Mines Ministers Conference in Whitehorse, Yukon, in September 1992 (hence, the name of the initiative). At that time, the mining industry was well aware of the serious challenges facing the industry, including significantly increased competition for mineral investment from other mining countries, coupled with an atmosphere of uncertainty surrounding land access, environmental regulations, and taxation. The diversion of investment abroad was hurting, and would continue to hurt, all Canadians. Something had to be done. At the 1992"

Jan 1, 1994

By D. Neely, D. Milne, L. R. Feldman

"Resin-anchored rebar is commonly used for rock support in mining. The rock properties and environment determine the average bond strength, allowing mine engineers to select the appropriate length and installation pattern for the support. In weak material such as potash, the average bond strength tends to be lower than for a typical hard-rock installation. Determining the failure mechanism by which the support fails in soft-rock applications could lead to improved bond strength and better calculated installed support capacity. This paper reports on research conducted at a potash mine in Saskatchewan and analyzes the failure mechanism of the support.RÉSUMÉ Dans les mines, les barres d’armature enduites de résine sont fréquemment utilisées pour soutenir le roc. L’environnement et les propriétés du roc déterminent la résistance moyenne d’adhésion, permettant ainsi aux ingénieurs miniers de choisir la longueur de barre appropriée et le diagramme d’installation du soutien. Dans des matériaux faibles, tels que la potasse, la résistance moyenne d’adhésion tend à être plus faible que pour une installation typique dans de la roche dure. La détermination du mécanisme de rupture selon lequel le soutien fait défaillance dans des roches tendres pourrait conduire à une meilleure force d’adhésion et à un meilleur calcul du soutien installé. Le présent article fait état de la recherche effectuée dans une mine de potasse en Saskatchewan et analyse le mécanisme de défaillance du soutien. ,"

Jan 1, 2016

By J. Gillies

"Extraction of Gold in Ketone from a suitably prepared sample of sulphide or siliceous ore or concentrate permits a rapid and accurate determination by Atomic Absorption. Mill test products and exploration development samples are acid-treated to effect complete dissolution of silver, copper, zinc, lead, molybdenum and iron present. Interferences in the determination of molybdenum are described. Results by Atomic Absorption are comparable to those afforded by other acceptable methods.INTRODUCTIONDuring recent years much has been written and discussed concerning Atomic Absorption Spectrometry as a technique for determining the concentration of metallic elements. We would, however, recommend a perusal of the paper presented by J. C. Ingles at the annual meeting of Canadian Gold Metallurgists held in Ottawa, January, 1966. The paper was published in the August, 1966, issue of the Canadian Mining Journal, and contains general information on Atomic Absorption.The purpose of our paper is to present certain specific method procedures for the determination of several precious and base metals normally present in Mine, Mill and Smelter products. Of necessity, analytical results should be as accurate as the most suitable available method permits, whether for metallurgical balance, settlement purpose, ore beneficiation programs, or exploration property development. The success of such programs is relative to the accuracy, speed and economics of the analysis. It is obvious, therefore, that in presenting our paper we consider the technique has achieved the desired evaluation."

Jan 1, 1968

By G. R. Yourt

"Generally speaking the usual approach for controlling dust is three-fold:1. Suppress the formation of dust at the source.2. Confine dust that cannot be suppressed.3. Dilute and remove dust that cannot be confined.This discussion will be concentrated on the second approach, namely, confining and disposing of dusty air.Dust BehaviourBefore delving into actual design principles a brief discussion on behaviour of dust should be helpful. For prevention of silicosis only respirable dust, ranging in size from < 0.5 to 5u needs to be controlled. As particles of this size have insignificant mass and momentum they follow air movements very closely. Consequently if contaminated air around dust sources is confined within enclosures and leakages maintained, strongly indraft dust is automatically controlled and capture velocities are of no concern.Dust SourcesAt metal mining operations ore is prepared for wet concentration by crushing it to mostly <3"" in size. This usually involves a jaw crusher, one or two cone crushers, one or more screens and several conveyors. Dust is actually produced only by the crushing action but it is liberated also when numerous fine particles contained in the ore stream are dispersed by surges and vibration at the discharge of the crushers, screens and headpulleys of conveyors. Furthermore, dust is dis¬persed when the slime adhering to the underside of the return portion of belts becomes dry and is rendered airborne by vibration and by cleaning floors especially where the slime has dropped."

Jan 1, 1971

By A. I. A. Salama, M. W. Mikhail

"The existing methods of block diagram manipulation and vanishing variable for flowsheet simplification used in coal and mineral processing circuit evaluation and optimization cannot be easily implemented on digital computer.The signal flowgraph technique is proposed to represent and simplify determination of the relationship between intermediate or end variable and the feed in the flowsheet. Typical and existing circuits are used to demonstrate the application of the proposed technique which can easily be implemented on digital computers.IntroductionRecently there has been much interest in the analysis and optimization of coal and mineral processing circuits to assist in the pre diction of coal and mineral processing plant performance. The block diagram and the vanishing variable were introduced and utilized in the analysis of plant flowsheet. Although the block diagram approach is useful, it requires manual manipulation of the circuit block diagram which may present difficulties in the situation of complex circuits. Moreover, it may not be easy to implement on a digital computer.In this paper, the signal flowgraph technique is proposed to represent the circuit flowsheet and to simplify the determination of relationships between intermediate or end variables (fractional mass) and the feed for any coal and for any mineral processing circuit comprising size and density separators. These relationships are utilized in the analysis and/or optimization of the circuit. The proposed technique is illustrated by considering typical and existing circuits."

Jan 1, 1987