Search Documents

By Tyson C. Birkett

Initial indicator mineral sampling covering 425,000 square km of northern Quebec and subsequent follow-up of positive results convinced the Ashton ? SOQUEM joint venture to acquire mineral rights to 380,000 hectares prospective for diamond in late summer, 2000. Drilling in 2001 and 2002 identified eight kimberlitic bodies, all significantly diamondiferous. Commercial size stones (retained on a square mesh sieve with openings 0.85 mm) and encouraging grades have been returned by several bodies tested to date: The Renard bodies are formed by steep-sided breccia pipes with kimberlitic matrix surrounded by irregular outboard breccia zones within country rock. These bodies were emplaced in high-grade metamorphic rocks of the Superior Province of Archean age. Orthogneiss with lesser tonalite hosts the breccias, although regionally paragneiss is also present. Diatreme facies portions and nearby country rock are intruded by minor to major (Renard 1) amounts of hypabyssal-facies kimberlitic rock. Renard bodies are macrocrystic, with large olivine crystals set in a groundmass of olivine, phlogopite, monticellite, spinel, carbonate, apatite and serpentine. Proximity of various Renard bodies, with most in a core area of 0.5 square km will allow planning of an efficient mining operation. Geophysics, especially magnetic surveying, has contributed to identifying bodies of kimberlitic rock.

May 1, 2003

By A. Putz, F. Vincent, A. R. Laplante

"This paper briefly reviews some of the gravity research done at McGill University and current Canadian operating practices, with emphasis on results of interest for operators. The following topics are addressed: security, economics, predicting recovery, circuit optimization, unit selection and final upgrading. Emphasis is placed on the Knelson Concentrator.The topic of security and economics are addressed jointly, in terms of the place of the gravity circuit in the mill flowsheet. Actual plant experience is drawn upon to identify potential problems and actual solutions.Predicting primary recovery is linked with a characterization of the ore, the choice of a circuit, and the fraction of the bleed used. Factors such as feed preparation, preliminary upgrading, fraction of recycle treated, ability to recover fines and location of the bleed are discussed.Final upgrading is achieved almost only by tabling and smelting. This can lead to fine gold recovery problems when more effective units are used upstream. Alternatives are discussed.IntroductionResearch on gold recovery by gravity over the past eight years has associated McGill University with a number of gold producers. This paper attempts to review the information gathered from a practical perspective. Some of the information was generated in McGill University's labs, some gathered at plant site, and some was shared by operators."

Jan 1, 1994

By A. P. E. Dirige

The stability design of cemented backfills is normally conducted using conventional approaches. Analytical or numerical models, backed by trial-and-error methods, are the primary means used to describe or predict the support performance of backfills during mining. The stability of paste backfill free-standing faces is a major concern due to potential consequences to production, ore dilution and safety. Available analytical or mathematical models are developed based on assumptions of the failure modes that may occur when vertical fill faces are exposed during adjacent mining. Numerical modeling serves to provide an understanding of backfill strength and deformation behaviour. Such approaches offer inherent limitations and generally result in conservative designs. In this paper, centrifuge physical modeling was conducted not only for performance evaluation studies, including stability analysis, but to develop an understanding of the strength and deformation behaviour of paste backfill exposed faces when the adjacent ore zone is removed. The failure mode and mechanics of failure observed in the centrifuge model of a given prototype situation are discussed in detail. Centrifuge model results were compared to numerical modeling and it was concluded that a sliding block failure mechanism that resembles a circular slip appears to be the predominant failure mode.

Aug 1, 2013

By Victor A. Sowa

"Abstract - In 1938, a body of goethite and hematite was discovered beneath Steep Rock Lake near Atikokan, northwestern Ontario. This was at the time the largest and richest undeveloped iron ore body in North America. Mining began in 1944, fast-tracked by the needs of World War II, and through 1979 produced 79 Mt of 56.5% Fe. Production required the diversion of the Seine River, draining of Steep Rock Lake, building of a railroad, and a 25-fold increase of the local population. The mining project, at the time, was the largest project of its type undertaken in Canada. The current concepts of sustainable mine development and mine closures have advanced considerably since the period of operation and closure of the Steep Rock mines, and those operations would probably not have met current expectations of sustainability. However, some of the post-closure aspects of the mines provide illustrations of components of sustainability, which could form part of a basis for a post-mining sustainable land use plan. It is concluded that some of these components were successful in meeting current expectations of sustainable use, and although some aspects are unique to the circumstances at the Steep Rock mines, others could be applicable at other mine sites."

Jan 1, 2003

By Michael Hopp

The beginning of the electroforming technology dates itself on the beginning of the industrial revolution 1800 to 1820 approximately. Basis was the existence of electricity in order to be able to drive the electro-form-process. With the development of the electroforming, big names of the science-history, like Michael Faraday (1791? 1867), Sir Humphry Davy (1778?1829), Max Schlöter (1878?1946), Werner von Siemens (1816?1892), and many others. Already about 1840, the first monograph originated to electroforming (38). While in the first years the electro-forming most extensive only to the coating of art - or other usefulness-objects was used. At the beginning of the 20th century the formation of objects from pure metals became more and more, later also from alloys to application. One of the first bigger electroforming factory, the ?Württembergische Metallwarenfabrik? was working 1894 in Geislingen / Steige, Germany. In the industrial application, the electroforming-technology is to be imagined away for miscellaneous coatingtasks and the form-body-preparation no longer today (18). A little bit confusing is the german name ?galvano-technology?. It based on the Italian physiologist and naturalist Luigi Galvani (1737 ? 1798). This technically seen is however wrong, right, the name is electroforming. The physical bases were founded mainly by Michael Faraday and Sir Humphry Davy.

Oct 1, 2003

By Bo R. Arvidson

"New permanent magnetic alloys have recently opened up possibilities for development of unique mineral separators. These are now making several new applications feasible. In many cases where conventional electromagnetic-induced roll separators have traditionally been used, the new permanent magnetic roll separators may reduce both over-all capital costs and operation costs.The development of the next generation of extremely powerful permanent magnets, i.e. neodymium-iron alloys, is progressing rapidly and will affect the roll separator as well as another type of magnetic separator. Permanent Magnet Roll SeparatorDesign and FeaturesDiscs of permanent magnets interleaved with soft iron discs constitute the basic magnetic roll design (Fig. I). By enveloping the magnetic roll with a thin abrasive resistant belt (Fig. 2), even highly magnetic particles are removed.The first prototype roll utilizing the new magnets was shown to have approximately equal strength as induced magnetic roll (IMR) separators. Since the initial test roll, the new separator, called the PERMROLL® , has been made twice as strong with regard to magnetic force, that is, the magnetic flux density is determined to exceed 1.7 tesla (17 kilogauss), while the magnetic field gradient is more than twice the gradient than can be practically achieved with IMR."

Jan 1, 1985

By E. Contestabile, T. R. Craig

"This report describes the development and effective use of shaped charges as part of the Elliot Lake Mine Roof Stability Project to remotely remove the heads from roof bolts. With a slight modification, these same shaped charges are being recommended f or use to the Brunswick Mining and Smelting Corporation Limited (Mining Division), to cut steel cable bolts.IntroductionThe Canadian Explosives Research Laboratory (CERL) often receives requests to cooperate in solving problems encountered in private industry or other sectors of the government. CERL is equipped to design and test explosive and pyrotechnic devices and the policy is to treat each case individually.The first case reported evolved from a request from a sister laboratory at Elliot Lake. The intent was to remotely remove the head s of roof bolts as part of a mine roof stability project. The device designed for this use was 1000,70 effective in the laboratory and 80% effective in the mine.The second case reported results from a request from a private mining company knowledgeable of the Elliot Lake Project. Their requirement was to remotely cut cable bolts. This request was first treated as presenting a new problem. The solution, however, proved to be very similar to the former."

Jan 1, 1985

By I. Filzwieser, S. Konetschnik, A. Filzwieser, A. Anzinger

Production in copper electrorefining tankhouses mainly depend on two factors: The deposition area, which is a result of the amount of installed cells and cathodes, as well as the current density - the amperage per square meter of deposition area. The present paper shows, that the most economical way of achieving a certain production is to maximize current density by using the METTOP-BRX-Technology - as building and infrastructure can be kept more compact. This industrial proven technology applies a parallel electrolyte flow in each electrolysis cell. In 2011, the first fully industrial applications started up: At the secondary smelter Montanwerke Brixlegg AG, 156 cells are equipped with the METTOP-BRX-Technology; this allows a current density of 390 A/m². Xiangguang Copper Co., Ltd. - a primary smelter and refinery - operates its new tankhouse (720 cells) at 420 A/m²; this stands for an production increase of 50% compared to the same sized ISA tankhouse which is limited to 280 A/m². The first part of the present paper gives a cost comparison between a conventional copper electrorefining tankhouse and a high current density tankhouse when assuming a Greenfield project. The second part describes the cost savings when installing the METTOP-BRXTechnology in an already operating tankhouse.

Jan 1, 2014

By A. Galibois, R. Singhal

"This paper highlights some of the potential application areas of knowledge-based systems in the mining industry. The basic theoretical principles associated with knowledge-based systems are discussed and the justification for mining applications is given. The paper concludes with a brief description of a prototype knowledge-based system applied to scraper selection that was developed at Université Laval on a LISP machine. IntroductionThe beginning of Artificial Intelligence coincided with the conception and development of the first computer systems some thirty years ago. At that time researchers were euphoric about the possibility of modelling the human reasoning process. Soon, however, they discovered that the combinatorial aspect of the set of possible solutions to a particular problem did not permit an in-depth evaluation.In the mid-60s researchers started to look at the heuristic approach because it was more suited to human behaviour with its congnitive abilities (i.e. representing, reasoning, problem solving and advising). The heuristic approach allows possible results rather than exact solutions and it is more rapid and cost effective than the exhaustive combinatorial analysis. The heuristic approach did allow some noticeable progress in the seventies with the development of the first expert system called MYCIN with the objective of diagnosing blood infection diseases."

Jan 1, 1988

By C. John Sullivan

Is there a relationship among the Sudbury nickel ores, the Cobalt deposits, and the Huronian, Athabascan and North Australian uranium provinces? All are within intracratonic basins, with ore near basal unconformities. There are similarities in the geochemical "fingerprints" pointing to basic igneous rock affiliations. Some show a time relationship to basic igneous activity and to great rift systems. Many basic dykes show radioactivity at their edges. A spatial relationship between the uranium-cobalt-nickel ore at Midwest Lake, Athabasca, and basic igneous rock is reported. These remarks are not meant to imply, necessarily, a direct genetic connection between the basic dykes, etc., and the ore. In some cases, the relationship may be similar to that noted between basic and ultrabasic intrusives and volcanic massive sulphide ore deposits. Crustal thinning in these areas, associated with graben, appears to have favoured volcanic activity, as well as basic intrusives. Probably, the potential of the Huronian should be re thought . Athabascan-type ore may be present . New data on mineralization in Turner Township, Ontario, suggest this. The mineral possibilities of other basins should be reconsidered. It is to be remembered that the Athabascan and Kombolgie basins were neglected for many years. Intracratonic sedimentary-igneous basins contain many of the greatest mineral fields of the world.

Jan 1, 1979

By C. R. van Staal, L. R. Fyffe, J. A. Winchester

"The geochemical characteristics of Early Paleozoic volcanic rocks are used to establish the following tectono-volcanic regimes in the northeastern mainland Appalachians: foreland continental rift volcanics; fore-arc ophiolites; island-arc volcanics; back-arc ophiolites; and back-arc ensialic volcanics. A Late Precambrian calc-alkaline magmatic arc bounds the Early Paleozoic volcanics to the southeast.The Precambrian calc-alkaline volcanics of the Caledonian Highlands, primitive Cambro-Ordovician oceanic-arc volcanics of the Eastern Townships, and within-plate Ordovician volcanics of the Miramichi Highlands can be related to a progressive change in mode of subduction from compressional Andean-type in the Late Proterozoic to extensional Western Pacific-type in the Early Paleozoic. The development of marginal oceanic basins in the Paleozoic created a more favourable environment for volcanogenic sulphide deposition, particularly in back-arc areas.The influence of tectonic setting is reflected in the distribution, size and metal ratios of the massive sulphide deposits associated with the volcanic rocks; deposits within intra-oceanic arcs in the Eastern Townships of Quebec average two million tonnes grading 2.2% Cu, 4.0% Zn, and 0.6% Pb, whereas those within a back-arc, ensialic rift near Bathurst, New Brunswick, average nine million tonnes grading 0.6% Cu, 5.4% Zn, and 2.2% Pb."

Jan 1, 1990

By T. Patching

"COAL MINING at Canmore, Alberta, began in 1886 and continued there until July 1979. A comprehensive review of the Canmore operations is not available, but the following notes have been prepared to accompany references where more complete information about the operations and problems encountered may be found. The coal measures at Canmore occur in the Kootenay formation of Lower Cretaceous age, and at least twelve seams of varying thickness and horizontal extent have been recognized. The coal, of high quality, ranges from semi-anthracite in the lower seams to low-volatile bituminous in the upper seams. The strata of the Canmore area form an asymmetric syncline, the western limb being overturned to vertical by the Palaeozoic strata of the Mount Rundle Range. The eastern limb is more gently sloping, its dip ranging from IO to about 40 degrees. Tectonic movements have created a troubled and complex coal field. The seams were initially not regularly or uniformly deposited, and mountain-building activity folded and faulted the strata and in many places sheared and crushed the original structures of the coal(l,2,3,4,5). The lack of continuity of the seams, and changes in thickness and inclination, made longrange mine planning difficult and necessitated flexible methods of work, and the local disturbances sometimes created problems in roof support and contributed to the occurrence of sudden outbursts of coal and gas. Almost all of the coal was produced from underground operations but a few relatively small V-cut mines were worked along surface outcrops. These have all been filled in and revegetated. The basic method of underground work was by room-and-pillar, but many variations in layout and sequences were employed. Gangways were driven along the strike and pillars were formed by raises or slopes and crosscuts. Pillars were recovered to the extent that ground conditions permitted by splitting or taking 'skips' from the sides of the raises or splits or crosscuts. Because of the variety of conditions that existed in the field a considerable range of cutting, loading and support methods were employed, including hand-loading, slushers and scrapers, duckbills and shaker conveyors, mobile loaders and continuous miners. Except for the coal obtained by continuous miners most of the coal was broken out by blasting when driving narrow working places or by air picks when cutting from a face. In the early years hand loading onto cars or conveyors predominated. A continuous miner was introduced into Canmore in 1959 on a trial basis, and another was subsequently acquired, in order to minimize blasting and hand loading, but problems in operating these machines in inclining seams and difficulties in providing safe roof support for the machines and workers restricted their efficient use. Another major difficulty with the use of continuous miners was the problem of ventilating development headings in the very gassy conditions. In the early 1970s they were replaced by electric and compressed air slushers and scrapers, resulting in a general increase in productivity, roof control, safety, and flexibility of operations(1.6,7,8.9)."

Jan 1, 1985

By Z. D. Hora

Commercial production of barite commenced in British Columbia in 1940; shipments have been recorded from ten deposits, of which four are particularly significant: The Brisco, Silver Giant, Parson, and Mineral King mines. Parr of the barite production is a by-product of base metal deposits in which barite is a major gangue mineral. About one hundred occurrences are known. COMMERCIAL production of barite in British Columbia dates back to 1940. Production volumes rose and fell and reached 39,900 tonnes in 1972. The main producer is Mountain Minerals Limited . There are two principal areas of barite deposits in British Columbia: ( I) The southeast part of the province along the Rocky Mountain Trench , which is the source of all production to date. (2) Stratabound occurrences in northeast British Columbia in the Gataga-Ketchika rivers and Muncho Lake areas which are not yet developed. Of the approximately one hundred reported barite occurrences, only ten have recorded commercial shipments, some of insignificant amount. So far, four deposits have proved to be important producers: Brisco, Silver Giant, Parson and Mineral King. The Mineral King property is situated near the confluence of Toby and Jumbo Creeks, 35 km southwest of lnvermere. The lead-zinc-copper-iron-barite deposits, as described by Fyles (1959, 1962), replace Proterozoic Mount Nelson dolomites of the Purcell system on the limb in the trough of a complex, tight syncline. The mine operated from 1954 to 1967 and 2,097,900 tonnes of baritic ore that was processed for base metal concentrates and also produced 22,680 tonnes of by-product barite. Since 1970, some 136,000 tonnes of barite have been recovered from the old tailings pond. The deposit is now considered depleted. The Silver Giant mine is located 10 km northwest of Spillimacheen. Barite and lead-zinc sulphides replace Cambrian Jubilee limestone near their contact with the overlying Ordovician McKay slate. Mineralization is located in the nose of an overturned plunging anticline. Between 1951 and 1957 800,000 tonnes of baritic ore were processed for lead and zinc concentrate. After 1959 barite was also produced , first from open pit, and later from reworked tailings. Up to 1979 production of barite totalled approximately 180,000 tonnes. Two other producing mines in the area are descri bed by G.R. Manson (this volume). Large, bedded stratabound barite deposits are reported from northeastern British Columbia. Six major shale-hosted Industrial Minerals in Canada lead-zinc-barite occurrences are known in the Devonian Gunsteel Formation. These are: Driftpi le Creek, Mount Alcock, Cirque, Pie, Fluke and Elf. In addition, numerous occurrences of strati form blebby or nodular barite and locally massive white crystalline barite are known from the Driftpi le Creek and Ak ie River districts in Gunsteel shale and from the Kechika, Road River and Ware map areas from Silurian siltstone . The size of these deposits is impressive; the baritic horizon at Mount Alcock is reported to be 25 to 30 m thick , and dri ll ing results from the Cirque deposit indicate reserves of 30 mi llion tonnes of baritic lead-zi nc-si lver ore. Similar bedded barite deposits are also reported from Midway area, near the Yukon border.

Jan 1, 1984

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama, Ryuji Oinuma

"Recently, the arsenic grade in copper ores has been increasing year by year. Arsenic bearing minerals (enargite (Cu3AsS4) and tennantite (Cu12As4S13)) coexist with typical copper minerals such as chalcopyrite (CuFeS2). The removal of arsenic from copper ores that contain relatively high arsenic content is essential due to its adverse impact on the environment and the resulting economic consequences. In this study, arsenic removal and dissolution behaviour of Cu and As from enargite (Cu3AsS4) were investigated using ferric sulphate (Fe2(SO4)3) solutions containing sodium chloride under high pressure oxidation conditions. The effects of numerous parameters including the concentration of Fe2(SO4)3 and NaCl, temperature, total pressure, leaching time and particle size were studied while other variables such as pulp density and stirring speed were fixed at 100 g/L and 750 rpm. The results showed that more than 60% of the copper was dissolved in a 0.1 M ferric sulphate solution under the high pressure oxidative conditions, whereas the leaching rate of arsenic was less than 20%. SEM observation revealed that elemental sulphur was deposited on the surface of enargite forming a passivation layer and the residue was agglomerated. Those phenomena may cause a decrease in the copper leaching rate. It was found that more than 80% of copper was dissolved in the ferric sulphate solution in the presence of 0.34 M sodium chloride under the conditions optimized, whereas the dissolution of arsenic in the mixture did not exceed 2%. XRD analysis of the solid residues from the leaching experiments used ferric sulphate and mixtures of ferric sulphate and sodium chloride showed arsenic to be present as scorodite (FeAsO4).INTRODUCTION In recent years, there has been an increase of the arsenic (As) content of copper ores due to the gradual depletion of high grade copper ores. In some copper deposits, arsenic occurs in the form of minerals such as enargite and tennantite. The removal of arsenic in ores containing copper is critical to the production of pure copper and the management of the environmental challenges caused by the smelting process. Due to the environmental risk caused by arsenic emission and the deteriorated quality of the copper product, smelting of enargite concentrates is not an effective method for the extraction of copper (Padilla et al., 2010; Safarzadeh et al., 2014; Long et al., 2012). Therefore, a number of studies have been carried out to develop arsenic removal technologies from copper ores using various methods such as hydrometallurgy (Curreli et al., 2009; Tongamp et al. 2010), pyrometallurgy (Dalewski., 1999; Padilla. et al, 2012) and bio-oxidation (Ehrlich, 1964; Sasaki et al., 2010). Several hydrometallurgical leaching processes like sulphuric acid, alkaline sodium sulphide and sodium sulphate and ferric sulphate leaching have been developed to treat enargite ores and concentrates. The alkaline sodium sulphide leaching process has been developed for the removal of arsenic from enargite (Anderson, & Twidwell, 2008; Parada et al., 2014). The mechanism of the dissolution of arsenic from enargite in sodium sulphite solution is"

Jan 1, 2016

By E. De Souza

Energy associated with ventilating an underground operation comprises a significant portion of a mine operation's base energy demand and is consequently responsible for a large percentage of the total operating costs. Ventilation systems may account from 25?40% of the total energy costs and 40?50% of the energy consumption of a mine operation. Fans are the most important mechanical devices used to ventilate underground mines and the total fan power installed in a single mine operation can easily exceed 10,000 kW. Investigations of a number of mine main fan installations have determined their assemblage to be, in general, very energy inefficient. The author has found that 40?80% of the energy consumed by a main fan is used to overcome the resistance of fan assemblage components. This paper presents how engineering design principles can be applied to improve the performance and efficiency of fan installations, resulting in substantial reductions in power consumption, operating cost and greenhouse gas emissions. A detailed case study is presented to demonstrate that, by designing fan assemblages using proper engineering concepts of fluid physics and industrial ventilation design, main fan systems will operate at efficiencies well above 80?90% (compared to common operating efficiencies of between 20 and 65%), resulting in a drastic reduction in a mine's overall costs and base electrical and energy loads.

Aug 1, 2013

By Haibin Ma, Jie Song, Qingyou Han, Xiaoming Wang, Wei Vian

In the grain refinement of aluminum, Al3Ti and TiB2 particles are introduced to reduce the casting grain size down to 200 micrometer level, which makes cold working possible. The particles are brought in by the addition of Al-Ti-B type master alloys. It is generally believed that TiB2 particles are stable and nucleate a-Al grains in solidification in the presence of extra titanium than the stoichiometry of TiB2 from the dissolution of Al3Ti particle in the master alloys. Titanium in solution either form Al3Ti layers on the surface of TiB2 particles or as solute to promote the nucleation and to restrict the growth of a-Al grains. However, a consensus on a grain refinement mechanism is still to be reached due to the lack of direct observation. This paper presents finding on the TiB2/Al3Ti interfaces in an aluminum matrix. It demonstrates a strong epitaxial growth of Al3Ti on the surface of TiB2 particles, a sign of the formation of an Al3Ti layer on the surface of TiB2 particles in grain refinement practice. The Al3Ti layer has a crystal coherency with a-Al and hence offers a substrate for heterogeneous nucleation of a-Al grains.

Jan 1, 2015

By M. Mirnezami, J. A. Finch

The McGill component of the consortium contributed detailed examination of the electrokinetic properties of the constituent minerals, primarily pentlandite and serpentine. Mineral specimens were derived from an ore sample; mineralogical examination showed the serpentine was predominantly clinochrysotile, a fibrous mineral responsible for much of the flotation separation problem. The study included design of a novel sedimentation potential measuring device to classify the surface charge of the ore and electrophoresis measurements on single and mixed minerals which progressively approached flotation conditions. The sedimentation potential measurements provided a general association between surface charge and the visual state of aggregation as a function of pH. The electrophoresis experiments started with single minerals in a background of indifferent electrolyte and progressed to mixed minerals in a background of supernatant derived from an ore sample. The single mineral tests supported the suspected electrostatic interaction, i.e., hetero-coagulation, at flotation pH 9-10. The mixed mineral tests demonstrated this interaction and also revealed hetero-coagulation with Mg(OH)2 precipitates, derived from the supernatant. This interpretation was confirmed by optical and electron beam imaging. A series of agents, CMC, polyphosphate, soda ash, EDTA, were examined to disperse the system. To accommodate the small mass of single mineral available a novel turbidity measurement using a UV/Vis spectrophotometer was introduced. Selected conditions were used in contact angle and small-scale flotation tests.

Jan 1, 2011

By Jacek Paraszczak, Stefan Planeta

"RésuméDans la première partie de cet article on discute Ie contexte technico-économique de l'usage des foreuses à l'eau sur béquille dans des mines sud-africaines. Par la suite on présente les résultats d'une étude comparative du forage avec les foreuses à l'huile et à l'eau par rapport aux foreuses pneumatiques. La performance des foreuses est discutée sous les deux aspects: l'aspect technique concernant Ie taux de pénetration et la quantité d'eau rejetee dans les galeries et l'aspect de fa santé et sécurité au travail, et plus particuliérement, les niveaux de bruit et de vibrations ainsi que Ie brouillard de l'huile. On conclut par l'évaluation du potentiel de forage à I'aide des foreuses hydrauliques dans Ie contexte canadien.AbstractIn the first part of this paper the technical and economical aspects of water-powered drilling are discussed. This technology, originally employed in South Africa, received some interest from Canadian mine operators. In this context a comparative experimental study of pneumatic and hydraulic (oil- and water-powered) jackleg drills has been realized. The performance of the drills is compared and the results reviewed with regards to technical aspects (penetration rate, amount of water spilled) as well as health and safety considerations (noise and vibration level, presence of oil mist). The potential for application of hydraulic jackleg drill is discussed."

Jan 1, 1995

By STEPHEN V. FORGERON

The Loch Lamond celestite properties in central Cape Breton Island were mined by Kaiser Celestite Mining Limited from 1970 until 1976. Poor market conditions in J976forced operations to cease. Kaiser holdings included the Lake Enon, MacRae and A mac prospects. A total of about 272,000 tonnes of raw celestite have been mined. Celestite deposits are situated in the Loch Lamond Basin, specifically in Lower Windsor sedimentary rocks. Of the five formations in the Lower Windsor Group, celestite is found in the upper four. Celestite in the Enon Formation occasionally replaces shale that separates stromatolitic dolomite columns; elsewhere in the formation it occurs in association with siltstone and gypsum. Jn the B2 Limestone Formation celestite fills pores or grades between limestone and gypsum. It replaces both limestone and silty limestone conglomerate in the Loch Lamond Formation; this limestone is of unusually high grade (60 to 70% SrSO,J for the area. Evidence indicates that the Uist Formation may hold important celestite reserves. Original celestite mineralization probably resulted from evaporation of seawater on mudflats or 'sabkhas'. Secondary mineralization also may have occurred. Strontium ions could have been leached from pre-existing concentrations and overlying gypsum, moved downdip in groundwater and combined with sulphate rich waters to deposit as celestite in porous B2 limestones.

Jan 1, 1984

By Oberlando Gonzalez, Claudia Serna, Andrea Alzate, Esperanza López, Maria Holuszko

This paper presents a systematic approach on gold recovery from electronic waste (e-waste) using ammonium persulfate. This process was developed as a response to the lack of hydrometallurgical systems capable of separating gold from its metallic substrate without material grinding, with minimum formation of pollutants, and achieving a lower reaction time. Computer memory boards, electronic processors and electronic pins and contacts were analyzed to determinate base metals (Ni, Fe, Cu) and gold (Au) using microwave plasma atomic emission spectroscopy (MP-AES). An aqueous commercial grade ammonium persulfate with oxygen and pressure was used to produce the persulfate anion (S2O82-) and the oxidative sulfate ion (SO42-), which partially oxidized and leached the base metals breaking the Au-Ni-Fe-Cu bonds and allowing gold to be recovered in its original non-leaching state. The influence of the oxidative parameters was evaluated using full factorial (FF) and central composite designs (CCD) with response surface methodology (RSM) and first and second order models were developed. Using RSM allowed to obtain a faster recovery of gold, minimizing the agent consumption. The findings presented suggest that optimized quantities of ammonium persulfate, oxygen, pressure, temperature and liquid solid ratio could be used for selective oxidization of the base metals and to extract more than 96% of gold from e-waste.

Jan 1, 2017