Search Documents

By Percy Coulter

"GeneralThe Malartic Gold Fields mill is presently treating ore from four different companies. The ore is delivered by truck, by the shipper, and dumped into the Malartic Gold Fields ore bin. This ore varies in size from 'Run of mine' to minus 8 11, All ore is crushed to pass a 3/ 8 11 x 4 11 cross slotted screen.Weighing and SamplingAfter crushing the ore passes over an adequate-weigher (250 T .P.H. capacity) on its way to the fine ore bins. This weigher has a remote counter at the sampling point.A 36” Vezin sampler cuts 15% from the ore stream as it enters the mill bins. This portion is elevated, by means of a short belt conveyor, to feed the No. 2 Vezin sampler. (This elevation is necessary to give headroom for the following machines). The ore on the conveyor is levelled to give a uniform stream to the second sample cutter. The second, third and fourth cutters are 2411 •The No. 2 Vezin sampler cuts 19% from its feed and this portion falls directly into a 1611 x 1011 Denver rolls crusher. This crusher reduces the ore to -1/ 8 11 , approximately. The discharge from the rolls crusher falls on a revolving circular plate with scraper, which gives a uniform stream to the No. 3 Vezin sampler.The No. 3 Vezin cuts 10% from its feed. This portion falls on another revolving plate to give a uniform stream to feed No. 4 Vezin."

Jan 1, 1966

By R. Pelletier, Herny. E., C. Allaire

Corrosion of refractory linings by molten metals is controlled by interactions between penetration and chemical reaction. Corrosion of aluminosilicates by molten aluminium is no exception. The early stage of corrosion can be described as a particular case of reactive wetting over a porous medium. Although the reactivity between aluminium and silica is great, which should improve wetting and penetration, the presence of air and the formation of a protective oxide layer disfavours initial penetration. This paper presents the results of an exploratory study on the effect of some parameters on the initial stage of aluminium penetration. Penetration kinetics and metal intrusion tests have been performed on alumina and silica powders with pure aluminium and Al¬5%Mg. Capillary models are used as tools of interpretation. Penetration kinetics tests had a poor reproducibility and the kinetics itself can not be explained very well by the capillary-tube-bundle model. On the other hand, a capillary model initially developed for ice intrusion into freezing soils produced predictions in reasonably good agreement with intrusion pressure measurements. The effect of particle size and alloy composition can be predicted using this model. However, the effects of temperature and powder chemistry need additional interpretations to be rationalised. An unusual resistance to penetration of silica powder by molten aluminium have been observed in a series of experiments. This led the authors to the strange conclusion that oxygen should be seen as an excellent non-wetting agent and that there might be ways to use it in industrial applications.

Jan 1, 2004

By Fabian Mohr

The methyl substituted binuclear cyclometallated gold(I) complexes [Au2(?-n-MeC6H3PPh2)2] [n = 4, 5 and 6] all undergo oxidative addition reactions with halogens and, in the case of the 4- and 5-methyl substituted analogues, with dibenzoyl peroxide to give metal-metal bonded digold(II) complexes [Au2X2(?-C6H3-n-MePPh2)2]. The 4- and 5-methyl substituted digold(II) compounds on warming or exposure to light undergo carbon-carbon coupling reactions to give gold(I) complexes containing the corresponding 2,2'-n,n'-biphenylyldiphenylphosphines. The 6- methyl substituted digold(II) complexes rapidly isomerise above ca. -20° C to binuclear heterovalent gold(I)/gold(III) compounds [XAu(?-2-Ph2PC6H3-6-Me)AuX{?2-(6-MeC6H3-2-PPh2)}], containing a fourmembered cyclometallated ring on a gold(III) centre. Surprisingly, no carbon-carbon coupling could be induced for any of the 6-methyl substituted compounds, even under forcing conditions. This difference in reactivity of the 6- methyl derivative, compared to that of the 5-methyl and unsubstituted analogues was studied by ab initio calculations using a series of model compounds. The results are in excellent agreement with the experimental findings and suggest that the key-step in the C-C coupling reaction is the partial opening of the Au(III)-P bond in one of the transition states. In the 6-methyl system this transition state is energetically inaccessible and hence no C-C coupling occurs.

Oct 1, 2003

"In mills, metallurgical efficiency is important in every step of the operation through to the tails. Different problems which hinder metallurgical efficiency exist in different mills. One such problem occurred in the Bralorne mill at the tailings end of the circuit, where the washing efficiency of the filters was so low that serious losses in dissolved gold occurred.The new cyanide plant at Bralorne went on stream in August 1961. Test work done showed that: a flowsheet of grinding in water, jigging, thickening, agitating, followed by double filtration, gave satisfactory results and was more economical than a counter current plant. Two filters, 141 x 161, with approximately 700 square feet of filtering surface on each, were purchased and installed in series. Test work showed that this was ample filtering area for 500 tons per day.When the plant started up a density of 45% solids was maintained in the agitators, and a 20 ounce cotton dl1ck was used on the filters. Vacuum was between 23 - 25 inches. Under these conditions the filters would not work and only picked up a very slight skim of pulp. Various speeds were experimented with, 4 minutes per revolution being the most efficient. At this speed the thickness of the pulp on the filters increased to about 1/8”• It was therefore quite apparent that, under these conditions, the filters would not handle very much tonnage and the mill tonnage would have to be reduced drastically until the problem was solved."

Jan 1, 1967

By Murray D. Fredlund

The consolidation of soil material is central to many types of engineering analysis. Problems such as the building of highway structures, landfills, or buildings over saturated soft clays require application of such theory. It has been found in industry that the application of consolidation theory has lagged significantly behind the theory which has been developed some time ago. The application of small-strain saturated consolidation theory was first proposed in a 1D form by Terzaghi. Although this theory has been available for some time it?s implementation into software packages in 2D and 3D forms has been slow due to inherent complexities in the coupling equations. The flow and stress equations are also inherently somewhat unstable and this further complicates software implementation. Of particular interest in the mining industry is the consolidation of uranium tailings. One such disposal method that has been utilized is the subaqueous deposition of uranium tailings in large pit structures. When performing such deposition the calculation of consolidation rates is central to determining final pit capacity and expected life. Consolidation software can be successfully used in such cases in order to determine pit filling rates. The primary complexity, however, is that tailings are typically deposited in slurry form and therefore the potential deformations are large. Large-strain consolidation theory is therefore required in order to properly solve the deformations over time. This paper presents the use of a large-strain consolidation analysis in order to predict long-term filling rates in a uranium tailings pit.

Aug 1, 2010

By Jeffrey S. Loen

"Abstract - The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 X thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

By Gordon. I. M., J. Blackshaw

"The wet part of the Hollinger mill is housed in two buildings, the grinding plant and the treatment plant. In the grinding plant there are four 7xl5 ball mills which grind the ore to 60 per cent through 200 mesh. There is also one 7xl5 ball mill which grinds table concentrate to 9 5 per cent through 200 mesh.The primary classifier overflow is pumped to the treatment plant where it passes over shaking tables, producing a concentrate and a tail. The concentrate pulp is pumped to the grinding plant for secondary grinding. The secondary classifier overflow is pumped back to the treatment plant where it is thickened in two 40xl 5 tray thickeners and agitated in four 20x24 mechanical agitators arranged in series of two (with 2 spares).The table tail pulp is thickened in nine primary 40xl5 tray thickeners (with 2 spares). The thickened table tail pulp and the concentrate agitator discharge pulp are mixed and pumped to four rows of 15x45 pachuca agitators, arranged in series of five tanks.The pachuca discharge pulp is divided. The smaller part goes to two rows of 3-step decantation using 40xl5 tray thickeners (with 2 spare rows). The larger part goes to six 14xl6 drum filters. The repulped primary filter cake and the thickened pulp discharged from the decantation rows are fed to eight 14xl6 drum filters. The secondary filter cake is mixed with water and pumped to the tailing line."

Jan 1, 1968

By Jeffrey S. Loen

"The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 x thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

By C. Allen, M. Gangal, J. Stachulak

"Most underground diesel equipment is equipped with diesel oxidization catalysts (DOCs) to reduce carbon monoxide and hydrocarbon emissions. DOCs do not alter nitrogen oxides concentrations but can promote the oxidization of nitric oxide (NO) to the more toxic nitrogen dioxide (NO2). Vale and CanmetMINING have been researching how to reduce worker exposure to diesel emissions by testing mining equipment DOCs. Results indicate a > 77% decrease in carbon monoxide concentration but a 46–315% increase in NO2 concentration for 8-mode test cycles. It is recommended that DOCs that increase NO2 emissions be evaluated regarding their continued use in underground operations.RÉSUMÉ La plupart des équipements miniers souterrains sont équipés de catalyseurs d’oxydation diesel (DOC) afin de réduire les émissions de monoxyde de carbone et d’hydrocarbures. Les DOC ne modifient pas les concentrations des oxydes d’azote mais ils peuvent faciliter l’oxydation du monoxide d’azote (NO) en dioxyde d’azote (NO2), plus toxique. Vale et CanmetMINING effectuent des recherches pour réduire l’exposition des travailleurs aux émissions de diesel en analysant les DOC des équipements miniers. Selon les résultats, une diminution > 77 % dans la concentration de monoxyde de carbone est atteinte mais elle est accompagnée d’une augmentation de 46 à 315 % de la concentration en NO2 pour des cycles d’essais à 8 modes. Il est recommandé d’évaluer les DOC qui augmentent les émissions de NO2 pour décider de la poursuite de leur utilisation dans les opérations souterraines."

Jan 1, 2016

By Gaston Giuliani, Jérome Massot, Didier Bourlès, Lionel Siame

"Abstract - We present a new approach for the evaluation of the potential of emerald reserves in gem projects using beryllium (Be) mobility. The distribution of Be in the different phases of hydrothermally altered (albitized) black shale hosting Colombian emerald deposits indicates that Be mobility is associated with the breakdown of Fe-Mn oxyhydroxide phases. The amount of Be that can be mobilized (~0.7 x 10-6 g/g; i.e., 0.7 ppm) may represent up to 18 wt% of the total Be contained in the black shale. A mass balance calculation applied to a well-constrained alteration zone of the Chivor mines, and based on the quantification of Be that can be mobilized under hydrothermal conditions, gives an estimate of the total gem reserves of these mines. Resumé - Une nouvelle approche, basée sur la mobilité du béryllium (Be) pour l’évaluation des réserves d’émeraude dans des projets d’exploitation de gemmes est présentée. La distribution du Be dans les différentes phases minérales de schistes noirs hydrothermalisés (albitisés) qui contiennent les gisements d’émeraude colombiens, indique que le Be mobilisable se trouve dans les oxyhydroxydes de fer et de manganèse. La quantité de Be potentiellement mobilisable (~0,7 x 10-6 g/g; soit 0,7 ppm) constitue jusqu’à 18% poids du Be global contenu dans le schiste noir. Un bilan de masse appliqué à la zone d’altération hydrothermale des mines de Chivor et basé sur la quantification du Be mobilisable, donne une première estimation des réserves à émeraude de ces mines. rieur."

Jan 1, 1999

By Donald Leroux, Robert Grant

"Flotation is a complex and highly multivariate process. Using the conventional OFf (one-factor-at-a-time) technique, the optimization of flotation circuits through laboratory or plant testwork is difficult, time-consuming and therefore, expensive and often results in marginal improvements. The optimal operating conditions can be more efficiently estimated when a systematic approach like SDE (Statistical Design of Experiments) is taken.The concentrator of Noranda's Brunswick Mining Division (near Bathurst, New-Brunswick) is well known for the complexity of its differential copper-lead-zinc flotation circuits. One of them, the chalcopyrite-galena separation (or CuSep) circuit, is impacted by more than 20 variables.Statistical Design of Experiments (SDE) techniques were applied at the laboratory scale to improve the performance of Brunswick's CuSep circuit. Screening tests were conducted using Fractional Factorial designs while optimization tests were carried out based on Response Surface Modelling techniques like the Central Composite design. Every series of tests, without exception, revealed new information and process insights which led to significant circuit performance improvements in the plant So far, the metallurgical gain may be as high as four percentage points of copper recovery (in the CuSep circuit). Potential cost savings of expensive consumables (steam, activated carbon) have also been identified but will require additional circuit modifications before being realized.IntroductionIn spite of its apparent simplicity, flotation is a complex three-phase (solid, liquid and gas) separation process. Fundamentally, it is a highly multivariate process. Industrial flotation circuits are commonly affected by 10 or more process variables."

Jan 1, 1997

By Frank Wright

"The Icon Sullivan Joint Venture ore deposit was discovered in June, 1965 by Messrs. Paul Benard, Bob Galipeau and Mac Watson working under the direction of Mr. Andrew J. Troop, as employees of the Icon syndicate. The deposit is located on the Waconichici River as the south end of Baie du Poste of Lake Mistassini, approximately 45 miles north of Chibougamau. Property acquisition and Winkie drilling was followed by a diamond drilling program to evaluate the deposit. Stripping of the open pit area connnenced in the late fall of 1966 and the first test sample of ore was shipped to Chibougamau in December of that year.Regular ore shipments to the mill of Merrill Island Mining Corporation Limited for concentration commenced May 25, 1967. Production to December 31, 1970 amounts to 42,960,000 pounds of pay copper.The ore is chalcopyrite in white quartz dolomite, and it contains a very small amount of precious metals. The quartz dolomite assumes a flat to gently dipping attitude and is associated with a graphitic argillite contact zone on both hanging and footwall sides, in dolomitic limestone rocks. There is practically no other sulphide present in the ore.During the summer of 1969 a series of pre-concentration tests were completed and a Wemco heavy media sink float plant was installed in late 1969 and early 1970. This pre-concentrator eliminates at least one third of the ore mined in the form of barren quartz dolomite prior to ore shipment by truck to the concentrator in Chibougamau."

Jan 1, 1971

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai."

Jan 1, 2017

By M. Leroux, C. J. Martin, S. R. Rao, J. A. Finch

"The effect of nitrogen on the flotation separation of sulphides from complex ores from Brunswick Mining and Smelting (New Brunswick) and Mattabi Mines (Ontario) was investigated. The most significant finding was enhanced pyrite floatability after as little as 3 minutes nitrogen conditioning. This was used in a novel sphalerite/pyrite separation process developed on the Brunswick ore. After aeration and Cu/Pb bulk flotation in air using xanthate the slurry was nitrogen conditioned, xanthate added and the pyrite floated in nitrogen. As an example up to 70% pyrite recovery with about 20% sphalerite recovery was achieved. Sphalerite was recovered from the pyrite tailings and the pyrite concentrate by copper-activation, raising the pH to 10 and floating in air. About 65-70% recovery at 35-40% Zn grade was achieved compared to 25% Zn grade by the conventional route. The process offers a promising alternative to current practice which seeks to depress pyrite at all stages. A possible mechanism of the effect of nitrogen is presented. INTRODUCTIONUse of gases other than air in froth flotation has been reported from time to time. [Podobnik and Shirley, 1982; Lin and Metzer, 1975]. Of all the gases, nitrogen would appear to hold the greatest practical promise because of its easy availability and chemical inertness. It is used in froth flotation in chalcopyrite-molybdenite separation [Redfearn, 1983]. The use of nitrogen in polysulphide chalcopyrite. this case is mainly to reduce the oxidation of a compound (Nokes reagent) used as a depressant for There is no reported use of nitrogen in the flotation of other sulphide minerals."

Jan 1, 1988

By Karl Houseley, Dr. Robert J. Chapman

"A gravity concentration process has been applied to ores from the Clogau Mine, north Wales, the Tyndrum deposit, central Scotland and an alluvial ore from Leadhills area of Scotland. In the case of the Welsh ore and the alluvial deposit the gold grains in the concentrate and tailings streams have been characterised in terms of their three dimensions.In the case of Welsh ore, the thickness of a gold grain has been shown to be the single most important factor in determining behaviour in a gravity concentration operation. Six indices were used to quantify the overall geometry of the gold grains and those which incorporate a thickness term have proven to be effective in predicting the destination of gold particles within the concentration circuit. It is proposed that the most simple of these, the Heywoods flakiness ratio, has potential for the control of milling operations as an alternative to the established practice of characterising the size of the mill discharge.The effect of grain geometry on the recovery of fine gold has been studied using Tyndrum ore. The recovery of gold by gravity concentration increased from 20% to 70% when the criteria used to design the milling operation was the prevention of over grinding of gold grains.The destination of alluvial grains in the concentration circuit did not show such dependence on shape, and this has been attributed to the effective classification of all the gold grains in the sample by fluvial action producing a population of similar geometric characteristics."

Jan 1, 1996

By Michael K. Watkeys, Jacobus E. Potgieter, E. Guy Charlesworth, Carl R. Anhaeusser, Roger L. Gibson, Alexander F. M. Kisters

Intrusive features of cupriferous noritoids from the deeply eroded Proterozoic granite-gneiss terrane of the Okiep Copper District in South Africa illustrate the emplacement of basic magmas into a mid- to lower-erustal environment. The small, easterly trending intermediate to basic intrusions of the so-called Koperberg Suite display a wide variety of geometries, occurrence and emplacement modes, including dike-, sill- and plug-like bodies. Coeval granulite-facies metamorphism, partial melting and ductile deformation of country rock gneisses during intrusion of the basic magmas led to emplacement and dilation processes of the intrusions which differ significantly from those described for dikes and sills at shallow crustal levels. Regional tectonic stresses are largely negligible due to very low differential stress [( )] during deformation and intrusion, which permits emplacement at high angles to the principal compressive stress and which follows favorably inclined structural anisotropies. Dilation of the basic intrusions is largely determined by compositional differences of host rocks and occurs by thermal erosion, i.e., assimilation of wall rock gneisses. Low length-to-width ratios of basic to ultrabasic dikes and predominantly diapir-like outlines of mesocratic bodies are indicative of low viscosity contrasts between the mafic magmas and high-grade metamorphic host-rock gneisses. Buoyancy-controlled ascent of the basic to intermediate intrusions is expressed by a broad compositional zoning of basic bodies with respect to the granite-gneiss stratigraphy. Various intrusion modes within the stratigraphic column of the granite-gneiss sequence reflect a lithological and structural stratification of the seemingly homogeneous granite-gneiss terrane.

Jan 1, 1994

By W. Yang, R. Rajasingam, B. Tadesse, K. Mohanarangam

Copper electrowinning is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. Acid mist is produced by these oxygen bubbles bursting at the electrolyte free surface. It is an undesired by-product of the Electrowinning process which unchecked could result in mist generation higher than the recommended time-weight-average exposure limit. Various approaches to alleviate the problem have been adopted by companies, all with varying degrees of success. All of these have been attempts to treat the symptom acid mist rather than the inherent problem, often proving expensive and, in some cases, ineffectual. In this paper, a new method was developed for acid mist quantification based on ‘total acid mist’ capture above the EW cell under well controlled conditions. With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables including current density, flow rate, temperature, etc. independently and their effect on bubble size, bubble velocity, gas hold-up as well as acid mist generation and its droplet size. Results show that total acid mist capture increases with an increase in current density but remains more or less constant between 300–500 A m-2. Total acid mist also shows an increase with increasing electrolyte temperature. These findings are substantiated with the aid of bubble size and gas hold-up measurements with the transparent EW cell.

Jan 1, 2019

By Tim Robinson, Michael S. Moats, William G. Davenport, Andreas Filzwieser, Andreas Siegmund, Shijie Wang

This survey continues the long tradition of providing a snapshot of operating data from industrial electrorefineries. It is a supplement to previous surveys that were performed in 1987, 1991, 1995, 1999, 2001, 2003, 2007, 2010, 2013 and 2016. Analyses of current data and historical trends are presented. Examples of innovations to reduce costs, improve productivity, and improve quality are provided. In general, refineries continue to increase productivity while treating anodes with more impurities. INTRODUCTION This manuscript analyzes global survey data provided by operating copper electrorefineries. This paper continues a series of surveys of copper refining tankhouses that started in 1987 (Schloen, 1987, 1991; Schloen & Davemport, 1995; Davenport et al., 1999; Robinson et al., 2003; Moats et al., 2007, 2013, 2016). In this installment, data collected from 2015 and 2018 will be presented and analyzed. The 2015 survey data were presented at Copper 2016 in Kobe, Japan. This survey will continue the analysis of previous data to illustrate long term trends in copper electrorefining, which were originally presented at the Davenport Symposium in October, 2014 (Moats, Robinson, & Wang, 2014). Refineries who supplied surveys are listed in Table 1. Cathode production data from 2015 and 2017/18 (from surveys presented in 2016 and 2019) are provided to indicate which plants provided surveys and when. This manuscript presents operating data for ~6.5 million tonnes of copper production, which represents 30–35% of the world’s copper electrorefining production. The detailed survey results are available upon request from the corresponding author.

Jan 1, 2019

By Robert Cameron, Colin Ashton, John MacNeil, Leo Piciacchia

"The in pit dam construction and utilities relocation, known as the East Mine Corridor Relocation (EMCR) project, was developed to extend the life of the east side of the Base Mine pit by two veal's. This will result in the recovery of an additional 80 million barrels of oil and delay expenditures associated with the opening of the North Mine by two years. To accomplish this, a large in pit earth structure was required to provide a new embankment foundation for relocating a public highway, four powerlines, a natural gas back-up pipeline, a substation, and a conveyor train. This structure would also he required as a temporary dam 10 contain mature fine tails on the west side until mining is completed in the east mine corridor area, that will then be filled with fluid.The in pit dam, known as The Highway Berm, is 2.5 km long, 63 m high and has 42 million m3 of engineered soil added to the already existing end-dumped soil volumes. To complete the design and construction of a structure of this magnitude, in the very short time frame of two-and-a-half years, presented many new challenges. The main challenges faced were: designing while construction was ongoing; designing without the use of clay cores or sand filters; using relatively non-select overburden material; proper dewatering and base preparation; changing from construction of 50 m high spoil piles to a high specification construction operation; compacting lifts with heavy haulers; constructing during the winter; and monitoring movement of the structure with satellites."

Jan 1, 1995

By E. G. C Charlesworth, M. J. Robertson

"Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots. Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confirmed largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semimassive sulfides within tension fractures which are folded, attenuated and fractured. An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994