Search Documents

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By F. Hashiuchi

In 1996, the Saganoseki custom smelter & refinery successfully shifted to a single flash smelting furnace operation and increased the copper production capacity to 450,000mtpy in 1998. As the next step, Saganoseki planned to further increase the productivity, especially in the area of P.S. converters and acid plant. As the results of modifications and operational improvements, the gas washing & cooling sections of the Saganoseki acid plant were consolidated from 3 to 2 lines, and increased the gas treatment capacity. The S02 converters in the acid plant were also modified to increase the acid production. By increasing the matte grade from 65 to 68%, six PS converters have been successfully integrated into four, while maintaining the production capacity and reducing the environmental burden in 2005. This paper discusses recent operational conditions and the results of implementation of technological improvements.

Jan 1, 2007

By P. G. Lazenby

This paper describes the latest instrumentation improvements in the INPUT Airborne E.M. System, particularly the new electronic signal-processing techniques. Several anomaly examples illustrating these techniques are shown.

Jan 1, 1973

By W. G. Brissenden

"ALTHOUGH I SHOULD FIRST REVIEW the state of the mining art as it is today, because of the shortness of time I will confine myself to a re-view of the more important advances in that art which have been made in the past two to three decades. Then, a look at the opportunities and the challenges which now present themselves will be more meaningfulFirst, some of the more impor-tant developments in underground mining:(1) The recognition that good ventilation, visibility and working conditions are essential preliminaries to efficient production has resulted in their incorporation as a matter of practice in modern mine planning. (2) The introduction of the car-bide bit and the re-introduction of the airleg drill, and the resulting sharp rise in productivity, were early postwar developments. (3) The recovery of the coarser fraction of mill tailings for use as mine backfill also is an important cost-reducing development of recent years -and this has led to cemented backfill, which, al-though more expensive, meets certain specific needs and has tremendous potential. (4) Great strides have been made in improving explosives' materials and explosives' accessories. Millisecond-delay electric blasting caps, which improve fragmentation and reduce the seismic effect of blasting, and the development and •application for underground use of explosives are but two among many such improvements. (5) Trackless mining methods, using quarry-type equipment in some instances and specially de-signed low-headroom trucks, loaders and carrier-mounted drills in others have been successfully applied. (6) Dual-purpose load-haul units are now in use loading and hauling from open stope drawpoints, and smaller versions of this type of unit are in use in cut-and-fill and other types of stopes."

Jan 1, 1968

By G. A. Frame, J. G. Patterson

The 24,000-tpd Frood-Stobie mill grinding circuit operation and control are described. Changes implemented during the past three years to improve grinding efficiency and capacity are discussed.

Jan 1, 1971

By J. Stachulak, M. Scobie

"This paper addresses the occurrence and indicated causes of conveyor fires in North American and European underground mines. Some significant convey or fires which have been experienced in recent years in Canadian hardrock mines are then reviewed. The nature of existing conveyor monitoring technology is considered in the context of such fire hazards. Experiences with new monitoring technology recently installed at several conveyor sites at Inca Ltd. mines are then reviewed.IntroductionFires associated with conveyors have long been recognized as a serious hazard in underground coal mines. Recently, however, there have been some significant conveyor fires in Canadian underground hardrock mines. These offer important evidence as to the nature and causes of potential hardrock mine fifes. They also warrant attention with a view to improving over-all mine design, ventilation and emergency preparedness.In addition, a new era in mine communications and monitoring technology has been entered which should offer improved capability to protect against such fires. This paper was motivated by the need to understand the causes and mechanisms of conveyor fires in order to improve their safety. This should be possible through implementing more effective monitoring systems, as well as improving conveyor design. Underground mines are becoming more intensively mechanized, with less human surveillance of equipment and a greater dependency on remote monitoring systems."

Jan 1, 1992

By R. E. Michelutti

"The Sudbury area environment became drastically altered commencing in 1871 with lumbering, repeated fires and early open roasting operations from 1887 to 1929. These combined factors had such a pronounced effect that approximately 24 square miles were totally denuded of any vegetation and 87 square miles were semi-barren to somewhat stressed.The two nickel producing companies in the area have reduced the sulphur dioxide emissions considerably over the years. Falconbridge Limited, alone, reduced sulphur dioxide emissions by 77% from 1971 to 1984.These reductions have resulted in improvements to the air, soil, lake and vegetation quality in the Sudbury area.INTRODUCTIONThe Sudbury area environment became drastically altered commencing in the 1870's with lumbering, repeated fires and early open roasting operations from 1888 to 1929. These combined factors had such a pronounced effect on the Sudbury environment that approximately 24 square miles (64 sq. km.) were totally denuded of any vegetation and 87 square miles (225 sq. km.) were semi-barren.Over the years, the Sudbury area environment has improved considerably. This has been due to emission cutbacks by both Inco Metals and Falconbridge Limited, coupled with industry, government and community reclamation programs. Before the improvements are discussed, a better understanding of the historical degradation is required."

Jan 1, 1986

By Hiroyuki Sano, Hiroshi Chida, Katsuya Toda, Takafumi Sasaki

Saganoseki Smelter & Refinery is one of the largest copper producers in Japan to produce 450,000 tons of new copper annually. Saganoseki used to operate six PS converters with "4 Hot-2 Blow" scheme, but managed to change its operation to "3 Hot-2 Blow" scheme with four PS converters, while maintaining the same production capacity. To achieve the operational change, the following improvements have been carried out; 1) Extending service life from 220 to 350 batches, 2) Shortening cycle time by increasing the blowing rate and the matte grade, 3) Reducing environmental impact by applying sophisticated fugitive gas collection system and 4) Saving energy by waste heat boiler’s modifications. The operational change has been successfully executed, and results in drastic productivity increase and cost reduction. Currently, Saganoseki is maintaining the efficient and consistent operation with 4 PS converters. This paper describes the above-mentioned improvements for increasing productivity and the recent operational conditions of the PS converters.

Jan 1, 2015

By M. R. Coffin

Since the plant startup in 1972, the leaching and jarosite precipitation circuits at the zinc plant of the Kidd Metallurgical Division have been reconfigured several times to improve overall performance, and/or to respond to market conditions. For the most part, the circuit changes have been driven by two market factors: the price of zinc and the price of silver. Until recently, circuit modifications undertaken to improve zinc extraction and recovery came at the expense of silver recovery, and vice versa. In 2004, the plant was modified once again to produce a precious metals-bearing residue, but additional leaching circuits were added to ensure that zinc extraction and recovery did not suffer as a consequence. The development of the zinc plant of the Kidd Metallurgical Division is updated in this paper, with a focus on the recent circuit modifications and associated control strategies that were implemented to maximize zinc and precious metals recoveries, and control the quality of the jarosite residue.

Jan 1, 2006

By D. P. Wilkinson

Flow field design is critical to determining fuel cell performance with respect to operating conditions. Flow fields are normally designed around their maximum power operating point with the goals of maximizing performance and minimizing pressure drop between the inlet and outlet of the flow field. At lower power pressure drop is reduced, and water management and reactant distribution issues can occur over the active area as well as issues with cell to cell reactant distribution in the fuel cell stack. Flow fields have fixed flow channel geometries and fixed active areas which determine the reactant flow characteristics over the operational range of the fuel cell. In this paper we discuss some of the benefits of a new approach of changing the flow field active area with changing operating conditions. Such benefits for future fuel cell designs could include improved cell performance and stability, improved cell to cell reactant distribution, reduced low current density failure modes, and overall system advantages.

Jan 1, 2005

By D. Lascelles, J. A. Finch, E. El-Ammouri

Flotation separation is expected to be related to the degree of dispersion of the pulp. For instance, highly aggregated systems may show reduced selectivity, reduced entrainment and increased flotation rate. In an attempt to test the impact of aggregation on flotation, we have taken advantage of the effect of Mg ions. Using combinations of Mg2+ and pH gave a wide variation in aggregation of several Cu-Zn ores (measured by settling rate) and corresponding flotation response was determined by batch tests. The trials were conducted on-site at Louvicourt and Agnico-Eagle. In a majority of cases a similar trend in aggregation and flotation selectivity (grade at given recovery) was observed. At Louvicourt, improved selectivity with increasing aggregation at pH 10.5 was found. At Agnico-Eagle, an analogous association between aggregation and selectivity was observed at pH 11.5. It is suggested that aggregation influences particle entrainment, the increased effective particle size reducing gangue recovery and hence improving selectivity.

Jan 1, 2004

By Wilson Pascheto

One of the main outcomes of a capital project is the reliability of a new plant, system or equipment. During 20 years of experience working in various capital projects for the mining industry, the author experienced failures which have caused significant losses to Owners, in many cases amounting to millions of dollars and almost jeopardizing entire projects. Often, failures were related to faulty design, shop fabrication and/or construction. Therefore, significant opportunities exist in the Mining Industry to improve the success rate of capital projects, improve on-line time at start-up, minimize the occurrence of unplanned maintenance due to equipment failures, and all this with positive contribution to health and safety. This paper presents some examples of failures and how they could have been prevented by proper Quality Assurance methodology. It also discusses some of the main challenges in the implementation of such methodology, including awareness of the Materials discipline and availability of trained Engineers.

Jan 1, 2015

By K. Mirkhani, P. Gebski, W. Ying

The campaign life of an industrial metallurgical vessels strongly relies on the quality and quantity of the refractory lining. An operating furnace or converter refractory lining can be assessed either by thermal modeling or by acousto ultrasonic-echo (AU-E) technique or a combination. AU-E is a Non-Destructive Testing (NDT) stress wave propagation technique that has been utilized on a wide variety of smelting vessels for over 12 years with good success. AU-E can determine the thickness of remaining refractory lining, estimate the thickness of build-up or accretion, detect and locate metal penetration and impregnation into the lining, and identify hydrated or cracked areas of refractory. This paper details the AU-E principles, equipment and recent improvements to the data analysis to further improve speed and accuracy. In addition, the paper discusses the AU-E accuracy and limitations through a diverse and vast array of practical examples including a comparison with thermal modeling and physical measurements.

Jan 1, 2011

By M. Sabau

The Electrowinning Plant at INCO's Copper Cliff Nickel Refinery is a precious metals upgrading plant. The feed to the plant contains copper, nickel, cobalt, iron, significant amounts of precious metals and some impurities. Copper is the most abundant element in the feed. This paper describes the major equipment and process changes over the last twenty years, geared to improve the tankhouse operation, workroom environment and recovery of copper from the acidic solution. Copper is plated on to titanium blanks using explosion-bonded crossrods, animal glue as a levelling agent, and an organic surfactant for mist control. The installation of the stripping machine in 2001 required a number of changes: cathode and anode contacts were redesigned, flat bus bars were replaced with dog-bone type, spacer boards for cathodes and anodes were installed, longer anodes started to be used, and the plating cycle was extended from seven to fourteen days. A number of initiatives for improvement are being carried out. Explosion-bonded crossrods are being replaced with titanium-clad crossrods. The plan for the near future is to increase copper production by increasing current efficiency and current density. The possibility of lowering the iron concentration in electrolyte and changing the acid mist control method is being investigated.

Jan 1, 2007

By P. W. Ware

The majority of all refined copper is consumed to produce electrical conductors. Most copper conductors are drawn into wire from 8 mm ETP copper rod produced from high purity copper cathodes. Southwire Company has more than 40 years experience using, designing, fabricating and marketing a process for continuously producing ETP copper wire rod. This process is called the SCR® (Southwire Continuous Rod) process. Today, approximately half the copper wire rod produced in the world, or more than one third of all refined copper consumed, is produced using the SCR process. Southwire has sold 75 SCR copper rod mills to metal producers and wire manufacturers around the world. Southwire is North America's largest electrical wire and cable producer. Southwire operates a 48 metric ton per hour SCR® copper rod system in Carrollton, Georgia. This allows Southwire to provide technical support for existing SCR® system customers based on first-hand knowledge. Rod fabricators and their wire customers are always striving for copper rod that improves productivity. They are looking for improved surface quality, finer wire sizes and fewer wire breaks per ton of rod drawn. This paper will present a brief history of the SCR® process, a description and recent process developments.

Jan 1, 2007

By Nick Vagenas

"Loading and transportation are important activities of the mining process. Automation of these activities in underground hard rock mining has been discussed for a long time. This paper deals with the performance evaluation of a prototype automatic Load-Haul-Dump (LHD) vehicle (a 7-ton GHH LF LHD model) operating in Zinkgruvan mine, Sweden. The purpose of the data analysis is to evaluate the operational and maintenance characteristics of the automatic LHD system in the mine. Graphical and numerical methods have been used for the statistical analysis of the data. IntroductionDuring the past years, the idea of integrated automation and tele-operation on Load-Haul-Dump (LHD) machines (Fig. 1) has attracted considerable interest in the Swedish mining industry. This is mainly due to the demand for improvement in the working environment and due to the rapid development of economic and reliable microprocessors for mining vehicles. Several advantages can be foreseen with the application of a Remote-controlled/Automatic LHD (RAL) system in underground mining. Some of them are (1)':• better utilization of working hours;• less interruption in production at shift changes;• better operational control of a fleet of vehicles;• improved safety; and• one operator may be able to operate more than one vehicle simultaneously."

Jan 1, 1993

By Donald Leroux, Robert Grant

"Flotation is a complex and highly multivariate process. Using the conventional OFf (one-factor-at-a-time) technique, the optimization of flotation circuits through laboratory or plant testwork is difficult, time-consuming and therefore, expensive and often results in marginal improvements. The optimal operating conditions can be more efficiently estimated when a systematic approach like SDE (Statistical Design of Experiments) is taken.The concentrator of Noranda's Brunswick Mining Division (near Bathurst, New-Brunswick) is well known for the complexity of its differential copper-lead-zinc flotation circuits. One of them, the chalcopyrite-galena separation (or CuSep) circuit, is impacted by more than 20 variables.Statistical Design of Experiments (SDE) techniques were applied at the laboratory scale to improve the performance of Brunswick's CuSep circuit. Screening tests were conducted using Fractional Factorial designs while optimization tests were carried out based on Response Surface Modelling techniques like the Central Composite design. Every series of tests, without exception, revealed new information and process insights which led to significant circuit performance improvements in the plant So far, the metallurgical gain may be as high as four percentage points of copper recovery (in the CuSep circuit). Potential cost savings of expensive consumables (steam, activated carbon) have also been identified but will require additional circuit modifications before being realized.IntroductionIn spite of its apparent simplicity, flotation is a complex three-phase (solid, liquid and gas) separation process. Fundamentally, it is a highly multivariate process. Industrial flotation circuits are commonly affected by 10 or more process variables."

Jan 1, 1997

By G. J. Desroches

"In order to improve zinc plant productivity, areas of low efficiency were identified. As a result, solution purification was improved, additional dust precipitator capacity was made available and a new zinc casting plant was installed. The effects of these and other changes are discussed and the expenditure and benefits reviewed. HistoryThe operation of the Flin Flon metallurgical complex including an electrolytic zinc plant commenced in October 1930. The design of the zinc plant was based on that of the Commonwealth Mining and Smelting Company at Trail, British Columbia, the Anaconda Great Falls Montana Plant and the Electrolytic Zinc Company plant at Risdon, Tasmania.The plant began with a design capacity of 60 tons per day and currently produces 255 tons per day. Since plant start-up, approximately 3.5 million ton s of zinc metal have been produced, most of it exceeding special high-grade specifications.IntroductionThe facility incorporates the basic process steps of roasting, leaching, purification, electrowinning and casting. Figure I details the flowsheet. During the late 1970s, management recognized that in order for the zinc plant to continue operating, it was necessary to introduce cost-effective practices.Study groups, consisting of design engineers and operations personnel, were formed to investigate the details of plant revisions.The objectives were to improve productivity by reducing manual labour, reducing energy usage, increasing zinc recovery, increasing metal output and reducing costs.This paper details the changes made during the period 1979to 1986 and shows how these changes have affected the productivity and economics of the zinc plant operation."

Jan 1, 1988

By C. Larsen, I. Orford, L. Strah, M. Renaud, P. Radziszewski

"An AG/SAG mill was commissioned at the Brunswick mine concentrator in October 1998. This paper discusses the original shell top hat liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits.The original liners were chrome-moly steel Norsteel with rubber grates and rubber-lined pulp lifters. The design was based on experiences of other AG/SAG mills and recommendations by the liner supplier, Norcast. Liner design modifications were made in an iterative fashion after observing the wear rate profile of the liners; over ten liner sets were implemented. Shell liner design improvements were supported by a design of experiments approach in conjunction with discrete element method (DEM) charge motion simulations. Design optimization took into account lining costs and impacts on operating performance. The team approach to the liner design improvements process is described with emphasis on the application of the design of experiments. The liner wear history and mill operating performance are presented."

Jan 1, 2005

By Norman O. Lotter, Lori Kormos, Greg J. Wilkie, Peter J. Whittaker, Johannes S. Stickling

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from Mineral Processing and Mineral Science.More recently, Process Mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX / WDX capabilities and an XRD, the development of Process Mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002