Search Documents

By C. Sui, J. E. Nesset, M. Li, J. Y. Kim, S. L. Chryssoulis

"A plant study of zinc rougher flotation at Brunswick Mining was conducted using lime, soda ash and a combination of both as the pH modifiers in order to establish the effects on sphalerite and pyrite kinetics and mineral selectivity. The plant sampling and analysis was augmented by surface analysis using TOF-LIMS, SEM and XPS as well as fundamental precipitation and surface-charge studies in the sphalerite Ca/C03/S04 system.The results revealed the important role of carbonate ions in cleaning the sphalerite surface for effective activation by CuS04 to occur, and the beneficial role of combined soda ash and lime in increasing pyrite and galena depression.1.0 IntroductionThe studies reported in this paper were initiated as part of an investigation into the causes of a particularly pronounced seasonal deterioration in metallurgical performance at the Brunswick Mining concentrator during the summer of 1995. The concentrator treats a complex base metal ore having a typical feed composition of 9.0% Zn, 3.5% Pb, 0.4% Cu and 100g/t Ag at a current throughput of 9,000 TPD, although at the time of the problem in 1995, the average production rate was closer to 10,500 TPD. Zinc, lead, copper and bulk (zinc-lead) concentrates are produced with overall metal recoveries of 86% zinc, 63% lead, 60% copper and 60% silver; results which are typical of the lower recoveries associated with fine-grained, highly complex VMS and SEDEX type deposits. The main economic minerals of interest are an iron-containing (7% Fe) sphalerite, galena and chalcopyrite with the main diluent (about 60% wt) being pyrite.Figure 1 shows a simplified flowsheet of the Brunswick milling circuit while the seasonal decrease in summer metallurgy in 1995 is illustrated in Figure 2. Of significance is the rapid drop in copper and lead recovery in June while there is an apparent delay until late August-September before the zinc deterioration reaches its lowest point. A more typical seasonal effect within the experience of the authors is the reverse of the Brunswick situation, namely an improvement in summer performance thought to be associated with improved differential flotation kinetics during warmer weather leading to better mineral selectivity. The historical Brunswick experience was particularly severe during the summer of 1995 with estimated incremental losses of $10 Million for this period. The potential of the very significant economic benefits to be gained from understanding and hopefully improving the annual drop in performance led to an investigation involving the minesite metallurgical group, the Noranda Technology Centre (NTC) as well as researchers in Professor Jim Finch's group at McGill and the surface analytical services and interpretive skills of AMTEL."

Jan 1, 1998

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher productivity rates and a resultant reduction in activity costs. Increased advance rates, by examination of the key components (face preparation and drilling, hole loading and blasting, scaling, mucking and support installation) in the development cycle, and optimizing these processes is a high priority for research in the Canadian mining industry. Support installation time alone is typically 36 to 46% of the total development cycle time. A reduction in support installation time or techniques and alternative scaling strategies could result in significant gains in drift development advance rates. Support Staging and hydroscaling within the drift cycle could offer alternative drift development sequences that could reduce the overall cycle time. MIRARCO?s research into the support and hydroscaling processes for rapid drift development also suggests that there are many other factors (e.g. mine ventilation services) that have a significant impact on the rate of advance. These factors should be considered to promote and manage safe and rapid drift development. Constraints to the rapid drift development processes can only be overcome by sound construction management practices. In other words, the goals of rapid drifting can be achieved by the implementation of contractor-type construction management. This paper examines various constraints and processes affecting rapid drift development and draws attention to other factors affecting safe rapid drift development.

Apr 1, 2005

By Brian Raymond

This paper will outline the problems and solutions of the new generation washeries, as well as the recent technological advances which are being considered for future coal preparation plants. The subjects to be covered will include: - reasons for considering coal preparation plants; - raw coal crushing and handling systems; - types of coal cleaning equipment being used versus new equipment being considered; - fine coal circuit sizing; - clean coal centrifuging and dewatering; - thermal dryer problems and changes; - fine refuse dewatering systems; - clean coal storage problems and changes; - materials handling within the plants; and - control systems for preparation plants. The design and integration of the various circuits that form a modern coal preparation plant have led to the creation of an exciting new field of industrial research. As the need for energy sources increases, efficient methods of preparing coals for specific markets will become more important.

Jan 1, 1979

By Wei Wang

The SMCO copper plant is located in DR Congo, and was designed by China NERIN Engineering Co., Ltd. The process is a typical hydrometallurgical plant with Leach-SX-EW, with the project treating the oxide minerals with agitation leaching, followed with three stage of solvent extraction and two stages of stripping, and using permanent SS cathodes to produce LME grade copper. Because of the special characteristic of the ore, what contains 2 different type of oxides (one high carbonate oxide and the other low carbonate), there are several new technical measures that have been developed and adopted for the plant. For example, different grinding, leaching, and filtering are used to treat different oxides. This paper, presents the project process, engineering design, construction and commissioning. The paper also describes some of the problems encountered during plant commissioning, such as the agitation leaching tank issues, and corrosion in the settler-mixer. This paper discusses some NERIN solutions to these problems, and explains the use of the CN filter, which is used to filter PLS to treat high level suspend solids, instead of the traditional sand filter. Finally, this paper also proposes steps / measures for further improvement for future plant operation.

Jan 1, 2014

By E. W. Williams

THE Ontario Research Foundation has developed a process for producing low-density steel shapes by direct reduction of iron oxide powders. The process is a combination of reduction, sintering (without compaction), and carburizing, and has been described by Cavanagh (1). Iron oxide powder, in the form of mill scale or highly concentrated iron ore, carefully sized, is poured into a porous mould. A reducing agent, generally coke breeze, is placed around this mould in a heat resistant sagger which is sealed off and heated to 2,000°F. for a number of hours. The coke/ ore ratio, the particle size distribution, the temperature and time of soaking, and the size and shape of the reduced product, determine the densities and carbon contents attained. The Defence Research Board sponsored a programme of research into some of the mechanical properties of the material (which was named Controlled Density Steel) and this paper is an account of various factors which govern the tensile strength of the steel. The ?practically attainable range of density is from 1.5 to 5.5 gm./ cc. but higher densities are obtained on hot working. This paper, however, is restricted to discussion of results for moulded products.

Jan 1, 1957

Microseismic (MS) methods offer one of the few ways to monitor a 3D volume of rock and essentially see into the rockmass and the regions of real time rock fracture. This is a critical component when considering workplace safety as well as the economic viability of a mining operation. New Gold Inc. New Afton Mine, an intermediate copper-gold mining company located 350km northeast of Vancouver in the south-central interior of British Columbia, Canada, has recently installed a MS system to help understand the block caving process in space and time. For a block cave mining operation is it important to utilize the MS events to map out the seismogenic zone related to the regions of stress concentration and fracturing mechanisms which lead to caving. The geological setting within the local array is complex, consisting of several distinct lithologies with unique material properties that each affect the microseismic signal differently. The block cave consists of a muck filled void, also affecting the seismic waveform path. This paper compares the use of a single velocity model to a variable velocity model which accounts for the differing lithologies and cave. The variable velocity method determined 3D raypaths for all source to receiver possibilities through five irregular shaped geological domains and the estimated cave. For calibration blast data, the variable velocity model is found to successfully decrease the error for event location from an average of 38m to 20m (47% improvement), and its importance to location accuracy is expected to increase as the cave develops in size.

Aug 1, 2013

By Nn Li

Energy consumption in commercial buildings has been increasing rapidly in the past decade. The knowledge of future energy consumption can bring significant value to commercial building energy management. For example, prediction of energy consumption decomposition helps analyze the energy consumption patterns and efficiencies as well as waste, and identify the prime targets for energy conservation. Moreover, prediction of temporal energy consumption enables building managers to plan out the energy usage over time, shift energy usage to off-peak periods, and make more effective energy purchase plans. This paper proposes a novel model for predicting heating, ventilation and air conditioning (HVAC) energy consumption in commercial buildings. The model simulates energy behaviors of HVAC systems in commercial buildings, and interacts with a multiagent systems (MAS) based framework for energy consumption prediction. Prediction is done on a daily, weekly and monthly basis. Ground truth energy consumption data is collected from a test bed office building over 267 consecutive days, and is compared to predicted energy consumption for the same period. Results show that the prediction can match 92.6 to 98.2% of total HVAC energy consumption with coefficient of variation of the root mean square error (CV-RMSE) values of 7.8 to 22.2%. Ventilation energy consumption can be predicted at high accuracies (over 99%) and low variations (CV-RMSE values of 3.1 to 16.3%), while cooling energy consumption accounts for majority of inaccuracies and variations in total energy consumption prediction.

Aug 1, 2013

By M. Potesser

In the past, different furnace types have been developed for use within the copper industry, with two common anode furnace designs typically used in copper smelting plants worldwide: the tiltable reverberatory furnace (KPO) generally used for the secondary copper industry and the cylindrical or drum type anode furnace (TRO) for handling a liquid blister charge generated in primary copper production. The disadvantage of the KPO is its design related to the longer refining period, because of the low bath depth, however it provides good conditions in the melting period due to its large bath surface. On the other hand, small amounts of scrap charged into the TRO increase the melting and dissolution period, but it provides good conditions for the refining period. The newly-developed elliptical furnace concept (TRE) offers the advantages of each of these furnace types. The special design allows melting of the scrap more efficiently than in the KPO and refining the liquid copper more efficiently than the TRO. This paper shows a metallurgical comparison of the three furnace types in regard to the melting period by heat technological considerations (optimized arch design) and of the refining period done by CFD with concentration on current, recirculation and dwell time of the gas in the melt. The paper outlines the possibilities for a reduction of the tap-to-tap time and energy consumption as well as for an increase of the production capacity, which can be achieved by applying the TRE instead of the conventional furnace designs.

Jan 1, 2007

By P. Miranda, K. Le, G. Maes, R. Peters

"The Mount Milligan Mine, owned by Thompson Creek Metals Company Inc. (TCM), started operations in September of 2013. It is located between the communities of Fort St. James and Mackenzie and is the first major metal mine to open in British Columbia in 15 years. Based on reserves as of January 1, 2014, it has an estimated 22 year mine life with 2.1 billion pounds of copper and 6 million ounces of gold in reserves. Like all commissioning operations, there have been issues achieving design throughput and recovery due to flow sheet design, equipment failures, control philosophy, and reagent scheme. Efforts to improve overall mill performance include equipment modifications, reagent screening and testing, and grind size testing. Applying these changes to the mill and working closely with the mine has resulted in continuous improvement each month as Mount Milligan looks to achieve the nominal design capacity of 60,000 dry metric tonnes per day in the later part of 2015. Considerable focus is being placed into ensuring size reduction equipment is utilized effectively. Additional modifications and tests are being undertaken to steadily improve processes and alleviate restrictions in the mill. This paper will discuss the start-up and present ramp-up history of Mount Milligan, the current mill processes, and the steps taken to achieve expected production numbers.OPERATION BACKGROUNDMount Milligan is an open-pit copper and gold operation wholly owned and operated by Thompson Creek Metals. It is located approximately 155km northwest of Prince George, British Columbia, between the communities of Mackenzie and Fort St. James. The copper-gold porphyry deposit contains a Measured and Indicated Mineral Resource of 706.7 Mt at 0.18% Cu and 0.33 g/t Au, containing 2.84 billion lb. copper and 7.50 million oz. gold. Mine life is currently estimated at 22.1 years (“Feasibility Update – Mt. Milligan,” 2009). The mill is designed to process 60,000 dry metric tonnes per day and produce 400 dry metric tonnes of concentrate per day averaging 25.5% Cu and 40 ppm Au. Concentrate is delivered by truck and trailer to Mackenzie followed by rail to Vancouver for overseas shipping to various customers.Mount Milligan is considered a “zero discharge” operation meaning no process or surface water will be discharged to the environment. As well, stockpiling is very limited and is only permitted for a short period of time. This scenario presents several unique challenges. Scheduling of ore/waste production must be carefully planned as waste rock is used to build the tailings storage facility (TSF). Reagent selection is also important as persistent chemicals will have a tendency to build up in reclaim water which feeds the process water tank."

Jan 1, 2015

By M. S. Badollet

"The study of the physical properties of asbestos minerals requires a careful isolation of the fiber from the wall rock and, at a later stage, a comparison of these physical properties with those of fibers that have passed through the milling and beneficiation processes.The effects of mineral impurities, loss of fiber length and the formation of extreme fines (asbestic and/or associated minerals) often show up in the formation of special asbestos products as well as in the commercial production of asbestos papers, mill-boards, asbestos cement products, plastics and insulation materials, and in the filtration of blood plasma and wines.Numerous test methods have been developed in Canada and in England for use in the asbestos industry. Special treatments of asbestos fibers have been used to improve their physical and chemical properties and to eliminate impurities.Numerous problems connected with the use of asbestos fibers are discussed, such as the effects of asbestos on filtration, surface area, surface treatments using organic or inorganic materials, the surface charge on the fiber, the presence of magnetite and air pollution elimination. Biological studies on finely ground asbestos, when dispersed in 0.9 per cent sodium chloride solution and then sterilized and injected into hamsters, show that by reducing the dose, the tissue damage can be largely avoided. In these experiments, Arizona asbestos fibers were carefully extracted from the wall rock, finely ground, and examined chemically and micros-copically for any mineral impurities that might be present so that any effect on the hamsters would be directly due to the presence of the asbestos. The harsh Arizona fiber induced more extensive tissue response than the soft fiber when tested in hamsters."

Jan 1, 1969

By A. M. A. Mohamed, F. H. Samuel, S. Alkahtani

"This article was undertaken to investigate the effect of nickel and zirconium additions on the strength of 354 aluminum cast alloy. The cast alloys were given a solutionizing treatment followed by artificial aging at 190 ºC for 2 hr. High temperature tensile tests were conducted at various temperatures from 25ºC to 300ºC. Optical microscopy and scanning electron microscopy were used to study the microstructure of the samples. The results revealed that the intermetallics phases of (Al,Si)3(Zr,Ti), Al3CuNi and Al9NiFe are the main feature in the microstructures of alloys with Zr and Ni additions. The results also indicated that the tensile strength of alloy decreases with an increase in temperature. The combined addition of 0.2 wt% Zr and 0.2 wt% Ni leads to a 30% increase in the tensile properties at 300ºC compared to the base alloy.INTRODUCTIONThe task of improving the mechanical properties in an aluminum alloy at high temperatures should include the knowledge of several factors which are related principally to a decrease in the strength of the metal with increasing temperatures. This behavior is linked to the change or deterioration in the principal metallurgical parameters of the specific cast aluminum alloy during its performance at higher temperatures. Most of applications of Al-Si casting alloys are generally used at temperatures of no more than 230°C (Lee & Chen, 2002). This recommendation is made in view of the fact that, for certain applications such as those required by the automotive industry, these alloys must operate over a wide range of temperatures and stress conditions where temperatures are liable to rise even higher than 230ºC (Robson & Pragnell, 2003).Aluminum-silicon-copper-magnesium alloys such as the 354 alloys show a greater response to heat treatment as a result of the presence of both Mg and Cu. These alloy types display excellent strength and hardness VALUES (although at some sacrifice of ductility and corrosion resistance. These alloys are used for a wide range of applications, such as engine cooling fans, crankcases, high speed rotating parts, structural aerospace components, air compressor pistons, fuel pumps, compressor cases, timing gears, rocker arms, machine parts, and so forth (Cáceres, Svensson, & Taylor, 2003; Rurrxia, Rong-de, Yu-hua, Cherrxi, Xiao-feng, Heng-rong, & H. Zhuang-qi, 2004)."

Jan 1, 2012

By B. Damjanac, S. Maxwell, D. Chorney, M. Grob, F. Zhang, J. Hazzard

"A hybrid discrete-continuum numerical scheme is developed to study the behavior of hydraulic fractures crossing natural fractures. The fully coupled hybrid scheme utilizes a discrete element model for a core domain, within which the hydraulic fracture propagates and interacts with natural fractures, and a surrounding continuum domain to better approximate boundary effects. The results show that the behavior of hydraulic fractures crossing natural fractures is affected by a combination of factors. Nevertheless, three fundamental crossing scenarios can be identified from all of the simulations: no crossing, partial crossing, and direct crossing. Each crossing scenario has a distinct injection pressure history which may suggest guidelines for interpreting field hydraulic fracture injection data. Additionally, the capability for these models to generate synthetic microseismicity makes them appealing for the integration of microseismic field data with the reservoir geomechanics for ultimately providing a practical engineering tool for improvement of well completion and stimulation. The model is capable of examining and verifying four different shear deformation mechanisms associated with a propagating hydraulic fracture. The natural fracture can fail solely due to the stress perturbation of the passing hydraulic fracture or it can fail due to a combination of stress and pore pressure changes across different types of interaction scenarios. The simulations also illustrate that the level of fracturing complexity increases as the number and extent of the natural fractures increase. INTRODUCTIONAlthough hydraulic fracturing technique has been applied extensively as a reservoir stimulation technique in the oil and gas industry for over 60 years (Economides & Nolte, 2000), it is one of the key factors promoting the shale gas boom in the past decade (King, 2010; International Energy Agency, 2014). The hydraulic fracturing of shales can be differentiated from hydraulic fracturing of conventional reservoirs by the fact that shale formations often have a pre-existing discrete fracture networks which greatly impact the hydraulic fracture propagation. Based upon field production data as well as microseismic observations, it is believed that so called “fracture complexity” may result from interactions between a created hydraulic fracture and pre-existing natural fractures and planes of weakness (Warpinski, 2009; Maxwell & Cipolla, 2011)."

Jan 1, 2015

By Terry A. Kirk

"This paper describes Derrick High Frequency Vibrating Screens and their process performance in grinding circuit applications. The benefits of screen sizing in closed circuit grinding are illustrated by case histories from a wide spectrum of mineral industries.INTRODUCTIONHigh capacity, reliable wet screening equipment is increasingly in demand by the mining and allied industries for separations finer than 1/.7 5mm (I/ mesh). The continuing search for improved energy efficiency and reduced steel consumption in comminution has Jed to greater scrutiny of every aspect of circuit design and operation, including the classifier efficiency (selectivity) function.Derrick Manufacturing Corporation has been developing high frequency screening machines designed specifically for grinding circuit applications since 1973. Successful installations are currently operating in iron ore, copper, coal, uranium, phosphate and other extractive industries."

Jan 1, 1984

By J. F. K. Brown

MR. T. L. McCALL: Planning ahead in coal-mining is essential, but the question may be raised, just how far ahead can we plan. You can overdo it: chat is, you can get in a rut. Never let planning get a hold on you to chat extent. You must be prepared to deal intelligently with any new conditions that arise, and to apply new discoveries. It may become necessary to abandon ? .your plan, make the best you can of the ground you have developed, and start again, with a new plan. So far as the submarine workings of the Dominion Steel and Coal Company are concerned, we cannot know definitely what lies ahead of us under the sea: we must ?base our tentative plans on assumptions, and, as we meet changing conditions, we must change our plans. In the case of inland mines it is possible to bore in advance, and consequently it is generally possible to set out your plans in advance, block out a section of the mine, and develop to obtain a uniform product for a whole year, or perhaps even longer. MR. J. B. MORROW: While planning in coal mining, we must bear in mind chat the consumer also is planning ahead. Some people will tell you that, in ten years time, the demand is going to be all for pulverized co al; others believe that the field for such fuel is limited. Needless to state, planning for a pulverized-coal market is quite a different matter to planning for a general grade, ore stoker, market. In planning, therefore, our endeavour must be to keep a jump ahead of the work being undertaken by the anthracite producers. This year, they are spending about two million dollars-money contributed, not by the Government, but by the industry itself-in the study and promotion of new and improved ways of burning anthracite. For example, they are perfecting small hot-water heaters, and one they have brought out weighs only about ten pounds. I feel that research of this type must be regarded as an essential part of planning in coal mining. We, in the soft-coal industry, are also planning types of more efficient burning equipment and doing other investigational work.

Jan 1, 1937

By J. Holtzhausen

"An analysis of operating costs for underground mining operations in the current global economic climate considers the financial burden for a ventilation system to be in vicinity of 30–50%. These operating costs are often overlooked by management teams in the greater scale of things when looking to save money in the procurement phase. This oversight to operational costs can be as little as the effective delivery of ventilating air to the work zone. One of the biggest opportunities for substantial savings and improvements can be realized in the selection of a quality vent duct that is suitable and fit for purpose. The key component to the selection process for quality products is a solid selection criterion that is followed during the tender process. This allows the management team to filter out unsuitable suppliers and products. The case study identifies some of the key components that were considered in the procurement and selection process for lay-flat ducting products. These included the characteristics and strength of the materials. The selection criteria also considered a ducted performance comparison that offers the best aerodynamic performance with some of the following components. • Airflow at Duct Face (m³/s or cfm), Fan Pressure (Pa), Air Power (kW or hp), Assumed Fan Efficiency, Annual Running Costs, K – Factor or Lambda, Leakage Factor, Joining Method and available Duct Lengths with weights. • Critical components considered were the current Testing standards available for: o Bursting Strength AS 4878.5, Mass AS 2001.2.13, Tensile Strength AS 4878.6, Tensile Strength AS 2001.2.3.1, Tear Strength AS 2001.2.10, Tear Strength AS 4878.7 • Other key considerations were: o Warranty Claim, Damage claims, Local storage / operations, community engagement and relationships, current testing data, previous issues, after sales service with technical assistance, etc. Hidden costs associated with product failures and operational stoppages are often not quantified during the tender process. Buyer beware. INTRODUCTION The largest constraint underground mining operations currently face are their operating efficiencies and electrical costs. The overall cost of an operations ventilation system and its components requires more focus to identify what opportunities exist to maximise efficiency and effectiveness. This tender process may not always be clearly understood and it should be broken down into fewer components to achieve quantifiable results."

Jan 1, 2019

By Dave Bulled, Jim Thompson, Tim Leriche, Mark Blake, Troy Wilkie

"A commitment to a core testing, plant modeling and reconciling technique has shown substantial economic benefits to IOC in terms of accurate production forecasting, smoother operation of the mill, improved expectations of throughput and co-operation across production departments from geology, planning, mining, and processing, to shipping of concentrate to market.This paper describes a successful seven year program of forecasting throughput of the autogenous milling circuit at the Carol Lake concentrator of IOC. Work started with audits of the grinding circuit in 2001 and benchmarking of the data collected from samples of mill feed and plant operation to the CEET mill design and throughput forecasting model.Initially 390 drill core samples were tested for SAG Power Index (SPI) to measure the energy required in milling, and the data distributed using a geostatistical technique across the two operating pits, so that hardness was estimated in each of the 40,000 blocks (or 1500 million tons) of potential ore. In 2004 a forecast of energy requirement, i.e. forecast of throughput for a given power availability at the mill, was produced for each ore block using the CEET model and used for mine planning to smooth plant throughput. The forecast for blocks mined on a monthly basis was reconciled with plant results over the next 2 years and minor changes made to the CEET model. The forecasting exercise was repeated in 2006 and in 2008 with the latest model based on the testing of almost 1300 samples of drill core at closer spacing.INTRODUCTIONThe contracting of sales to clients and the timely supply of products to meet those contracts is a cornerstone of good business practice. Ensuring the correct scheduling of production is a major concern of mining companies where the supply and qualities of the raw material is uncertain and production facilities are not flexible. This is particularly challenging when the product is of high volume and produced far from the customer, such as iron ore.Apart from the metal content of the ore being mined, the greatest impact on production scheduling is the throughput of the comminution section of the extraction plant; most notably when size reduction is achieved by autogenous grinding. The response of the mills to variability in the hardness of the ore can change throughput by as much as 50% from day to day at some plants."

Jan 1, 2009

By J. Coffin, M. Muinonen, D. Fragomeni, R. Multani, C. Deredin

"Rejection of pyrrhotite from pentlandite is of critical importance to the economics of nickel concentrate production and the main goal of the Strathcona milling operations. A joint team of XPS, Glencore Technology and Strathcona Mill personnel executed a comprehensive program of work to develop and implement strategies for increased Po rejection with focus on challenging ores containing high feed Po/Pn ratios (> 7) and significant hexagonal Po content (> 40% of total Po). This paper describes the team results including minerology, bench-scale flotation tests, and plant validation tests and modeling that have defined the path forward to improving the metallurgical performance and economics of the mill operation. Techniques to quantify hexagonal and monoclinic pyrrhotites were developed at XPS to assess the differences in their metallurgical behavior since their flotation responses are quite different. Mineralogical tools including QEMScan were extensively used to determine mineral liberation, associations, optimum grind size, and nickel deportment into pentlandite, pyrrhotite and non-sulphide gangue. Several reagents/strategies were evaluated during bench-scale flotation testing to significantly increase Po rejection. A significant shift in the Po-Pn selectivity and grade recovery curves was achieved using several strategies including the use of DETA and sodium metabisulfite, and regrind of the rougher concentrate and rougher cleaner/rougher tails.INTRODUCTION The Strathcona Mill is owned and operated by Glencore Nickel – Sudbury Integrated Nickel Operations and has been processing Ni-Cu ores from the Sudbury Basin since 1968 (valuable sulphides: pentlandite (Pn) – (Ni,Fe)9S8 and chalcopyrite (Cp) – CuFeS2). Currently Strathcona Mill receives ore mined from two main sources in the Sudbury area and produces two concentrate streams – a nickel-copper concentrate that is shipped to the Sudbury Smelter and a copper concentrate that is sent to the Fonderie Horne (Glencore Copper, Rouyn-Noranda). The general flowsheet currently used at Strathcona is displayed in Figure 1. It is highlighted by separate feed circuits for regular grade Ni ores and high grade copper ores. The copper circuit has a preflotation stage prior to a rougher-scavenger stage, a copper-nickel separation circuit, and a pyrrhotite (Po) rejection circuit."

Jan 1, 2018

By N. Razavinia

Most mining and metallurgical industries produce relatively large quantities of low grade waste heat which they vent, for the most part, to the environment. To date, little is being done to recover some of this heat and transform it from low grade to a high grade energy form such as electricity. A few decades back this was also true of paper, plastics and metals. Recycling was not a prominent activity. Today, we all know that it is and that recycling is a must for sustainable development. To this end, we feel that we are now at that point in time when the recycling of waste heat to electricity must be given serious consideration. By recycling waste heat one can achieve at least one if not two of the following benefits: 1) reduction in the carbon footprint ? by improving the overall energy efficiency of a process, and 2) production of electricity at an economically viable cost. We have developed a process that captures, concentrates and converts (3 C?s) waste heat to electricity. The process comprises 3 distinct interacting units. The first unit captures and concentrates waste heat using heat pipe technology. The second unit converts some of the concentrated heat to mechanical work which can then be readily converted to electricity. This unit is based on the classical piston/cylinder engine arrangement that is widely used by consumers to power systems with compressed air, for example. The third unit of the process dissipates the heat that the engine cannot convert to high grade energy. It also uses heat pipe technology to achieve this. The combination of the 3 units forms a unique system for recycling waste heat. This paper describes the system and it presents some results that show how the system can be made to be economically viable.

Aug 1, 2013

By K. Gardner

"Many deposits have a geological model developed early in the project stages, which is not always reviewed or modified as the project matures and production commences. Conversely, ongoing pressures, due to a combination of declining head grades, a push for increased revenue and a multitude of other reasons, leads to processing plant modifications, with the primary aim being to increase production. Often, the ore deposit knowledge is not sustained or developed during the operational stages to the level carried out during the prefeasibility and feasibility study phases. This results in the variability within the deposit being poorly understood and a lack of data and knowledge being available to support (and ideally optimise) operations particularly in an environment where the flow sheet has changed and ore feed requirements are complex.INTRODUCTION This paper presents a case study of ore deposit knowledge development and corresponding process plant operating strategy at the Ladolam Gold Deposit, commonly referred to as the Lihir gold deposit in Papua New Guinea. The gold deposit is located in a tropical equatorial climate on the east side of Lihir Island in the New Ireland Province of Papua New Guinea. Gold mineralisation was discovered in 1982, and was followed by a major exploration campaign by a joint venture between Kennecott (Rio Tinto) and Nuigini Mining Limited. The first drillhole was drilled in 1983, and after an extensive period of drilling consisting of 343 holes for 83,500 m, the final Feasibility Study was completed in 1992. The feasibility study was based on a Reserve base of 37.9 Moz in refractory sulphide ore, with gold extraction proposed to occur via whole ore pressure oxidation due to the refractory nature of the mineralisation. The Lihir Special Mining Lease (SML) was granted in 1995 to a new PNG company – Lihir Gold Limited, and Rio Tinto established Lihir Management Company to develop and operate the mine on behalf of LGL. Mining and processing of the deposit commenced in 1997. Newcrest Mining Limited purchased Lihir Gold Limited in August 2010, and subsequently completed a major plant upgrade including the installation of additional grinding, autoclave and carbon-in-leach capacity. Post commissioning of the upgrade, Newcrest has continued to increase throughput and production. A reinvigorated ore body knowledge development program has significantly assisted this process in identifying operating strategies for the process plant and delivering recovery improvement projects to address declining head grade and recovery due to increased stockpile feed and flotation circuit use."

Jan 1, 2017