Search Documents

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

By Deborah McCombe

"and Bill Roscoe, Consulting Geologist and Principal with Scott Wilson Roscoe Postle AssociatesMineral property valuations are carried out for a variety of reasons, such as mergers and acquisitions, non-arm’s length transactions, initial public offerings of stocks, support of audited financial statements, fairness opinions, determination of vendor considerations, litigation, expropriation, income tax matters and insurance claims.The CIMVal Committee was formed in 1999 to review and advise on approaches to the valuation of mineral properties. CIMVal is a special committee of CIM formed on the recommendation of the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission.After solicitation of views and consultation with various interested parties, the CIMVal Draft Standards and Guidelines for Valuation of Mineral Properties were released for comment in February 2002 and were finalized in February 2003. CIMVal’s objective was for the standards to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges. To that end, the standards contain many of the definitions and concepts of National Instrument 43-101, Standards of Disclosure for Mineral Projects, which came into force in February 2001.The intent of the CIMVal Standards and Guidelines is that mineral property valuations be carried out by appropriately qualified individuals and that all relevant information be fully disclosed. It consists of two parts: standards, which are mandatory in the valuation of mineral properties, and guidelines, which elaborate on the standards and provide guidance and recommendations for the valuation process and for reporting."

Jan 1, 2003

By Robert B. Parsons

"In all likelihood, Canada's mining industry would be adversely affected by corporate tax reform proposals actively being considered by the Department of Finance in Ottawa. When the next set of proposals for lax reform is released later this year as promised by Finance, the mining industry had better be prepared 10 take a hard look.IntroductionTwo federal budgets ago, in May 1985, Finance Minister Wilson tabled budget papers that were more massive in terms of volume than most federal budgets. Buried in this mass of documentation is a discussion paper entitled ""The Corporate Income Tax System-A Direction For Change"". When the discussion paper was tabled over one year ago, reaction from the business sector was almost nonexistent. By and large, the paper was regarded as nothing more than one more federal publication of mild academic interest.But, recent events suggest that this discussion paper for corporate tax reform could be the cornerstone for a series of changes to the tax laws which would have more profound and widespread effects for all sectors of the economy than any reform since 1971 . No industry in Canada can afford to ignore the movement afoot in Ottawa for corporate tax reform."

Jan 1, 1986

By T. Johnson, D. Kelley, J. Graham

"Hydrometallurgical processes can be exceptionally corrosive. Conditions associated with metal extraction and refining require materials of construction that can withstand process acids and acid chlorides at temperatures up to 90°C (194°F). Process vessels, piping, scrubbers and ducting can be rapidly compromised in these aggressive environments if not designed with care. Design engineers are challenged to find materials that can stand up to hydrometallurgical processes especially for copper, zinc, nickel, cobalt and uranium. This paper will evaluate material solutions to determine which provides attractive economics for initial procurement as well as high durability for reasonable life cycle costs.INTRODUCTIONMining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel cobalt and uranium have been particularly active.The world’s largest nickel mine – the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale’s Voisey Bay mine in Labrador. Voisey’s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $858 Million Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 – 250,000 MT/yr manganese carbonate.High nickel alloys and rubber lined steel have been used for decades to design corrosion resistant equipment for mineral processing environments. These materials demonstrate reasonable resistance to corrosion for most environments. Unfortunately, higher nickel alloys are quite expensive. Rubber lined steel is a bit more affordable but requires continuing service over time which ultimately drives up its cost as well. FRP (Fiberglass Reinforced Plastic) has also been used extensively in mineral processing for tanks, piping and ducting employed in aggressive environments. Today, more and more design engineers and material specifiers are calling for FRP composites for both new and replacement equipment used in the refining and processing of a variety of metal ores."

Jan 1, 2012

By D. G. Osborne

"The paper describes current 'tools' available to the coal preparation engineer for carrying out the evaluation of data, process design, selection of equipment and layout and design of coal preparation plants.Laboratory and pilot-scale equipment is widely available and test data can be used to provide valuable design information regarding capacities and sizing for specific applications. Pilot plants, unless they fit closely to the basic design envisaged for the eventual commercial plant, C(In often provide only limited useful information.Computing aids such as equipment simulation, plant modelling, etc. are becoming widely applied for establishing design criteria and investigating flowsheet options . Other computer tools such as computer-aided design systems are taking over some of the time-consuming tasks of detailed layout and design and estimation of quantities, etc. and providing the means for detailed examination of more than a single option.Besides computer modelling there is also physical modelling of plant buildings, plant sites and entire proposed mining areas; the former can be especially useful in finalizing design and threading' pipework and electrical reticulation systems through the plant without the resultant risk of impairment of flow, obstruction or wastefulness. Not the least of the benefits of plant models is the assistance provided for training new operating and maintenance staff."

Jan 1, 1985

By M. Sakamoto

Copper foil is an indispensable material for Printed Circuit Boards (PCBs). PCBs in turn are essential elements of all electronic equipment today and thus important for our living in the new age of IT. The requirements from the copper foil market have lately been increasingly strict and diversified due to the rapid technical advancements in miniaturized high-density electronic equipment and highly integrated semiconductors. Tight control of thickness, metallurgical properties, surface morphology and characteristics is needed. In this paper, both electrodeposited copper foil for PCB and rolled copper foil for the flexible printed circuit board are discussed, and the recent technical developments in these copper foil products are reviewed.

Jan 1, 2007

By J. Elderton

"The combination of A C induction motor and flu id coupling, of either the fixed or variable filling type, constitutes a simple, low cost, highly reliable drive unit, with many applications in the mining field.The paper will, however, concentrate on the variable filling fluid coupling in three principal applications-conveyor starting, infinitely variable speed control for slurry and slimes pumping and dewatering pumps for deep mines. Fluid couplings can be used with standard or custom-built control gear equipment, ranging from the most simple, time-based open loop types, to those having the latest microprocessor techniques.IntroductionThe first industrial applications of fluid couplings included their use in the mining field as hydraulic slip regulators for flywheel generating sets. These installations, usually rated at around 1700 to 2500 hp, were located at mine shafts where the electrical grid transmission lines were not strong enough to cater for the peak power demands of the cage winding cycle. In Canada, the first two significant examples of variable filling fluid couplings for mining were on conveyor drives, at Steep Rock Mines Limited, closely followed by the major iron ore handling term inal on the St. Lawrence River at Sept-Iles. Successful and reliable operat ion of the fluid couplings at these two sites set the pattern for use on many subsequent mining projects throughout the Canadian Continent."

Jan 1, 1986

By Glenn Kosick, John Starkey, Glenn Dobby

"A practical new test has been developed for SAG hardness determination. Using two kilogram samples of minus one inch diamond drill core or crushed muck samples, the Starkey SAG Test has been shown to give accurate predictive information which directly relates to on-stream SAG mill performance. Typical results and test criteria are discussed in the paperAchievements to date include:• Identification of hardness profiles and the location of hard and soft zones in a large ore body.• Accurate prediction of the hardness of a bulk sample by using an adjacent diamond drill hole.• Derivation of a plotted curve relating pilot plant power to laboratory relative hardness.• Demonstration that for every test done to date, the Starkey SAG Test produced a product size distribution identical to that produced in a pilot plant or full scale plant SAG operation.This test can now be used for blast hardness monitoring and short term control of mine production in existing plants and for identifying the proper locations for bulk samples in new projects. In addition, new SAG mill design can now be rationalized in a low cost way to eliminate unforeseen production shortfalls.IntroductionThis paper is presented to introduce the Starkey SAG Test, a practical new laboratory tool for measuring the relative hardness of small ore samples in a semi-autogenous grinding (SAG) environment. The test was first designed for use on diamond drill core samples during the prefeasibility stage of new mining projects, to provide new information about the ore body at reasonable cost. It is a new tool and does not replace existing pilot plant test requirements.The test will also be useful for throughput prediction in existing SAG plants by assisting in short and long term mine planning, where forecasting of metal grades and milled tonnage is used to control mine profitability. Because in-plant hardness testing has previously been unavailable on small samples, this test offers exciting possibilities for SAG mill operations where hardness variation is or could be a problem.The Starkey SAG Test provides the following benefits to the mining industry"

Jan 1, 1994

By C. P. Verschuren, P. W. Kingston, W. F. Caley

"In recent years, there has been rapid growth in the use of natural stone building and construct ion products. The largest growing markets are for pre-fabricated natural stone panels for interior and exterior wall facing and flooring. This increased demand is attributed to advanced quarrying and processing technologies, renewed appreciation for the aesthetic appeal of natural stone, and to the superior durability of natural stone when compared to glass, steel, and concrete. Geologically, plutonic rocks, and to a lesser extent marble and limestone/dolostone, are used extensively for these applications. This paper details the economic structure of the dimension stone industry, describes the necessary characteristics of a stone quarry, and outlines the geological criteria which favour an economic quarry.INTRODUCTIONThe world building stone industry has remained relatively stable over the last 5 to 6 years. In contrast, the North American stone industry has experienced substantial growth during that period. The increased use of commercial granite is primarily responsible for this growth, where use as exterior wall veneer for commercial, industrial, and institutional buildings represents the largest and fastest growing market.This increased usage in the construction industry has been sparked by the application of new technologies in quarrying, processing and installation , ma king natural stone more competitive with man-made materials which are energy intensive to produce, and have risen dramatically in price. The development of safer, time-saving stone installation techniques has also appealed to the liability-conscience construction industry. Finally, there is a trend by designers and architects toward utilizing long-la sting weather-resistant building materials, and a renewed appreciation of the aesthetic appeal of natural stone. The other large user of granite is the monument industry of North America which, although it has decreased slightly in recent years, still consumes approximately 40% of all commercial granite produced. The local use of commercial marble has remained relatively stable, and North America still relies heavily on European sources and suppliers. There has been some concern over the use of marble for exterior applications in areas subject to acid rain, and in colder climates where the marble ma y be vulnerable to freeze thaw cycles. Despite these concerns, the greatest problem is not with the structural breakdown of marble but the inability of some marbles to retain their polished finishes in the se environments. As a result, there has been an increase in the use of granite at the expense of marble for exterior applications. Finally, commercial marble is used extensively for interior flooring, wall s, counter tops, furniture, sculptures, and stairway components"

Jan 1, 1989

By B. Leonard

As of November 2012, the Alberta government listed 53 oil and gas, oil sands, and mining construction projects either proposed or currently under construction. These industrial plant construction projects have an estimated value greater than 105 million dollars. A common construction method employed for industrial plant projects is fast-track construction, which is used to reduce construction time. Contractors begin fast-track construction with highly generic scheduling information. This high level schedule turns into a lower level schedule as more detailed information becomes available. From a contractor?s perspective, a challenge faced using fast-track construction is the visualization of generic and constantly changing project schedules. This paper discusses the use of a Plant Information Modeling (PIM) system, designed to create a 4D animation to visualize project schedules for fast-track industrial plant construction projects. The proposed PIM system creates a modified project schedule by obtaining specific information from a generic construction schedule. Obtaining the information involves grouping schedule activities in accordance with the level of detail in a 3D model, and the level of detail in a project schedule. The modified project schedule is then used in conjunction with a 3D model to simulate the construction sequence in the form of a 4D animation. This allows for 4D visualization of project activities, installation dates, and crane movements. Furthermore, as engineering reaches completion, the PIM system creates a streamlined channel for schedule information updates to be easily uploaded into the model for a more accurate 4D visualization. Through analyzing a nonmodular construction case study, this paper discusses the successes and benefits of the PIM system for 4D visualization, such as increased productivity, shortened construction time, increased constructability, and decreased field costs.

Aug 1, 2013

By Heidi Fauser

The aim of the project was the development of an electroforming process for the production of medical implants out of gold. To prove the applicability of this technology, tympanostomy tubes were chosen as demonstrators. These barbell-shaped tubes are usually produced mechanically; of silicone or, for higher therapeutic demands, of metal ? gilded silver or gilded stainless steel. Gold electroforming of the tubes as an alternative manufacturing process would reduce the expenditures for the mechanical preparation and lower the corrosion susceptibility significantly. To obtain electroformed gold tubes of the desired shape, the following steps are necessary: fabrication of a negative template by drilling holes with countersinks in an insulated aluminium sheet, electroforming process, removal of the aluminium by using a sodiumhydroxide solution. For the optimisation of the shape and surface quality of the tubes respectively the simplification of the manufacturing process, various parameters were tested, e.g. aluminium quality and sheet thickness, type of insulation layer, substrate processing, hydrodynamic conditions, type of electroforming electrolyte, electrodes position, etc. The manufactured tubes were characterised in view of thickness distribution, hardness, surface roughness and purity in comparison to mechanically produced reference tubes. From the results obtained during the project it can be concluded that electroforming processes can be easily adopted for the manufacture of medical implants. The time-consuming electroforming process is by far compensated by the simultaneous production of an arbitrary number of implants.

Oct 1, 2003

By D. S. Flett

"The current state-of-the-art of chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is reviewed. General considerations regarding the various flowsheet steps are examined and options discussed. Then, individual flowsheets are presented and discussed. Finally, the forward prospects for chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is considered and conclusions drawn concerning the likely application of this technology in the future. IntroductionHydrometallurgical processes for treating sulphide concentrates, in general, have received considerable attention over the last three decades or more. Many flowsheets have been developed, many pilot-plant studies have been undertaken and several processes are now successfully operating. For example, direct ammoniacal pressure leaching has been used by Sherritt Gordon Mines since the 1950s to extract nickel from pentlandite concentrates, the roast-leach-electrowin route is widely used to recover zinc from sphalerite concentrates and direct sulphuric acid pressure leaching of sphalerite concentrates has been successfully commercialized. Also, Duval Corporation operated a direct cupric/ferric chloride leaching process (Schweitzer and Livingston, 1982) with electrowinning to recover copper from chalcopyrite concentrates, this process (now closed) being the only chloride process which has been commercialized for a sulphide flotation concentrate. Despite these developments, it has long been considered, particularly for copper sulphide concentrates, that direct hydrometallurgical processes are in the main unlikely to be able to compete successfully with smelting for large-scale operations of simple high-grade single metal concentrates. As long as such concentrates can be produced commercially, smelting is likely to remain the principal processing route (Flett, 1981). This view is being challenged nowadays through pressure leaching developments made by Dynatec and CESL in Canada and the recent start-up of the Western Metals Gunpowder plant at Mt. Gordon in Queensland (Flett, 2000). Complex sulphide ores offer even greater opportunities because of the ability to produce a bulk sulphide concentrate from the complex sulphide ore with considerably higher metal recovery than is often possible from the production of individual metal sulphide concentrates from differential flotation. Interest continues to focus on hydrometallurgical solutions to these processing problems, particularly with regard to chloride hydrometallurgy. This paper, therefore, reviews current state-of-theart with respect to chloride hydrometallurgy"

Jan 1, 2002

By L. D. Smith

"The economic evaluation of a mineral project requires a great deal of diverse information to be brought together in one place. The greatest concern is that there will be an error by omission, so it is useful to have a detailed list of what one needs to know in order to make a thorough evaluation. The list that is presented below is intended to act as a checklist for the person who develops and reviews an evaluation, and as a shopping list for the persons gathering data at the project site.There are varying degrees of detail required at the different stages of evaluation in a project, from the ""quick and dirty"" overview, to the pre-feasibility study, to a full detailed feasibility study, to a due diligence review. This list addresses most of the economic variables in a project and can be used for all levels of studies. Its purpose is to identify a variable or issue and to raise a question, which the reviewer can then pursue in more detail using increasingly more comprehensive checklists for each topic. While developed from the point of view of a new project, this list is equally valid for an ongoing operation."

Jan 1, 1994

By Nancy C. Mohn

?Even though the age of many existing coal units exceeds 30 years, these units continue to perform with excellent reliability and at a competitive cost with other fossil fuel units. ?NERC data shows a consistent increase in availability for all utility coal generation ?With the opening of power markets, the challenge for coal is to produce competitive electricity while meeting increasingly stringent, and costly environmental limits. ?During the 60s and 70s, subcritical steam power plants dominated the market. The emphasis was on scale-up to larger MW size units. ?In the last decade, we have seen interest in a broader set of technologies with new drivers: ?Fluidized bed technology was developed to respond to increased environmental requirements, particularly with lower quality fuels ?Supercritical pressure units have gained interest for both fuel cost savings and reduced emissions due to higher efficiency.

May 1, 2001

"In flotation research, relatively little attention has been paid to understanding particle-bubble detachment phenomena compared with attachment processes. With CFD models now incorporating attachment/detachment kinetics, it is important to obtain more accurate formulations for detachment probability. The formula most often used is due to Bloom and Heindel (2002) who proposed that the rate of detachment would equal the product of detachment frequency, as previously estimated by other authors, and probability of destabilization, as estimated previously by Schulze. These two factors both account for the balance between stabilization and destabilization forces, so the product accounts for this effect twice. An integrated procedure has been followed to estimate the overall detachment rate by re-analysing the process. In this analysis, detachment rate is calculated as the frequency of eddy-aggregate interactions (or “collisions”) sufficiently energetic to cause detachment. The Bond number analysis of Schulze has been incorporated into the turbulence frequency analysis of previous authors in an integrated way. The new formulation has essentially the same type of dependencies as the previous model, but gives a lower detachment frequency. Detachment frequency has been calculated using the new formula for conditions relevant to an industrial flotation cell. INTRODUCTIONIt is well known that the effectiveness of froth flotation for separating different minerals is limited to the particle size range of approximately 10–100 mm (Trahar & Warren, 1976; Trahar, 1981). Fine particles tend to follow fluid streamlines around bubbles limiting the likelihood of bubble–particle collision, while coarse particles can be more easily detached from bubbles before collection can be achieved.Phenomenological models have been developed to quantify the physico-chemical aspects of flotation in order to better understand factors affecting these limitations, and to suggest ways of broadening the window of feasible flotation. Koh and Schwarz (2008) have incorporated these models into computational fluid dynamics (CFD) models of flotation cells, which have then been used for design and scale-up purposes (Schwarz et al., 2015). The models are based on dividing the process of bubble–particle interaction into three subprocesses: collision, adhesion and detachment. Of these, the hydrodynamics of bubble–particle collision and the probability of adhesion have been studied most extensively, while the dynamics of detachment have received relatively little attention from investigators."

Jan 1, 2016

By B. M. Hamilton

"IntroductionTHE PROCEDURE and technique for drilling holes has probably undergone as great a change during the past ten years as any one of the other operations conducted in hard-rock mining. During this period, we have seen a change from the heavy leyners and drifters to the light jackleg type of drill machine; from steels that were forged and hardened on the bit end to the inserted •carbide-tipped rod, from the necessity of providing special bit-end fabrication and beat treatment of shank steels to the simple grinding or turning of a plain section on a shank with no heat treatment required for bit attachment.When the steel maker was first called upon to manufacture a hollow drill rod, it was required that the steel must not only have sufficient strength and fatigue resistance to cope with the stresses of service, but also must be capable of being heat treated on the bit end to a high hardness for resistance to wear and abrasion . Little was known at that time about alloy steels and the beneficial effects to be gained from additions of chromium, nickel , and molybdenum. So it was that the plain 0.80 per cent carbon analysis was selected, since it had already proven to be a suitable grade for chisels, hammers, and other such shock tools. This grade has long endured the test of time and is still used in considerable tonnage today, particularly by the construction industry.As the metallurgist learned more about the influence of alloying elements, a new hollow drill analysis was placed on the market in the early 'thirties'."

Jan 1, 1954

By CIM Mineral Resource, Mineral Reserve Committee

These Leading Practice Guidelines for Mineral Processing (LPGMP) were prepared by the Sub-Committee on Leading Practice Guidelines for Mineral Processing. The Sub-Committee reports to the Executive Committee of the Canadian Mineral Processors (CMP) which is a Technical Society of the Canadian Institute of Mining, Metallurgy, and Petroleum (CIM) and incorporates those members of the CIM who are concerned with the processing of mineral deposits. The LPGMP covers the involvement of mineral processing professionals, referred to as Practitioners in this document, in providing inputs to the estimation of Mineral Resources and Mineral Reserves and providing technical content for internal reports as well as public reports on mineral projects as required under National Instrument 43-101 Standards of Disclosure for Mineral Projects (NI 43-101). The LPGMP supplement the CIM Exploration Practice Guidelines (2018) and the CIM Estimation of Mineral Resources and Mineral Reserves Practice Guidelines (2019) which are referenced in Companion Policy 43-101CP to NI 43-101 and recognized internationally. The LPGMP consist of 3 sections: • Principles of Process Support in Mineral Resources and Mineral Reserves Estimation; • Appendix A – Use of Supporting Studies in Process Evaluation and Assessment for NI 43-101 Documentation; • Appendix B – Glossary of Terms Relevant to the LPGMP. The LPGMP deal primarily with the description of leading practice as it applies to the mineral processing and extraction of base metals, precious metals, and other mineral products by the application of mineral processing technology. Other commodities may be considered with future updates of these guidelines. It is expected that this is a ‘living’ document and that these guidelines will develop in the future to address the requirements of the mining industry, investing public, and mining professionals involved. Clarifications and changes to these guidelines will be done under the guidance of the Executive Committee of the CMP.

Nov 25, 2022

"Projections of demand for Alberta coal indicate a quadrupling of current production rates to some 70 million tonnes/year by the end of the century. About half of this output-comprised of subbituminous coal-will be required within the province, primarily for generation of electric energy. The remainder-roughly 70 per cent high-volatile bituminous (hvb) steam coal and 30 per cent medium- or low-volatile bituminous (mvb/lvb) metallurgical coal-will be exported, principally to Pacific Rim and Western European countries. Direct employment in mining and coal processing is projected to increase from the present ca. 3000 to at least 12,000 persons.This paper presents separate forecasts for subbituminous, hvb and mvb/lvb coal production in the period 1982-2000; notes a number of possible developments that could substantially modify these forecasts; and briefly discusses attendant infrastructure requirements. Attention is drawn to potential shortages of qualified manpower and to threatening inadequacies of transportation facilities.IntroductionDespite the dislocations triggered by the 1973 'oil crisis', energy budgets of Western industrial countries are mostly still in the very early stages of the anticipated transition to greater reliance on coal. Shift s to coal are still more often only talked about than being implemented; and the public policies which are essential for timely development of facilities for producing, transporting and using coal are in many instances not yet even broadly formulated, let alone enunciated.In these circumstances, long-range projections of coal demand and supply-even if restricted to internal requirements- are subject to greater uncertainties than usually afflict such forecasts.On the demand side of the equation, these uncertainties arise ultimately from linkages between a need for coal and the availability and pricing of OPEC oil. The current surplus of oil on world markets, which has recently forced substantial reductions of posted prices, is undoubtedly a transient phenomenon that is unlikely to have any long-term impact."

Jan 1, 1982

By O. Mejia, J. Drozdiak

"This paper summarizes a comprehensive energy and cost study comparing an existing SAG mill based circuit at Huckleberry Mine with two proposed circuits involving comminution technologies which are associated with energy efficiency: high pressure grinding rolls (HPGR) and high speed stirred mills. The specific energy requirements expressed as kWh/t for the proposed circuits were determined from pilotscale HPGR and stirred mill testing conducted at the University of British Columbia. Samples and operating data were collected from Huckleberry’s copper-molybdenum concentrator to evaluate current mill performance for comparison. To support the base case, the SABC circuit was modeled using JK SimMet® software. The main comparison focused on the complete energy requirements for each circuit, including materials handling equipment such as conveyors, screens, feeders and pumps. This paper also provides capital and operating cost estimates for each of the comminution circuits. The results showed that the HPGR - ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG - ball mill circuit at the same P80 grind size of 160 µm. At a grind of 80% passing 75 µm, the HPGR - stirred mill circuit showed a 34% reduction in energy compared to the base case. It was concluded that the energy reduction for the new flowsheets significantly improved the economics of the Huckleberry comminution duty.INTRODUCTIONUp until now, tumbling mills such as AG/SAG mills and ball mills have had a dominant bearing on the design and economics of comminution circuits. However, it is commonly agreed that the majority of employed comminution processes are energy intensive and energy inefficient, accounting for up to 80% of overall process plant energy consumption and having an efficiency of as low as 1% (Abouzeid and Fuerstenau, 2009; Fuerstenau and Abouzeid, 2002). The U.S. department of energy reported that there is a potential to reduce energy consumption in the metals industry by up to 61% from current practice to bestestimated practical minimum energy consumption; suggestions included the implementation of best practices and the adoption of energy efficient mining and mineral processing technologies such as advanced blasting techniques, high pressure grinding rolls (HPGR) and stirred mills (U.S. DOE, 2007)."

Jan 1, 2013

By V. K. Gupta

"Effect of mill speed on grinding kinetics has been investigated with a view to using mill speed as a manipulated variable for control and optimization of the grinding circuit performance under variable ore hardness conditions. Dry and wet batch grinding tests were carried out for quartz, limestone and cement clinker in a 29 cm x 18 cm laboratory ball mill. Mill speed values selected were 55 and 70% critical. In the case of dry grinding operation, with an exception of quartz, for all materials studied the effect of mill speed on grinding rate was found to be insignificant for sizes finer than about 35 mesh. In the case of wet operation, grinding rates were found to be approximately proportional to the mill speed. The implications of these results are discussed.INTRODUCTIONIt is well known that mill speed has a considerable effect on the grinding rate of the ore particles l-3 For particles of a given size there is an optimum speed at which mill grinding efficiency is maximum (i.e. specific energy consumption is minimum) 3•4. Mill speed can, therefore, be effectively used as a manipulated variable to deal with the disturbances arising from changes in the size and hardness (grinding rate) of the ore being fed to the grinding circuit. Though, it has not been the case so far, with recent developments of ring motors2 and frequency inverters5 a continuous variation of mill speed has now become feasible, and it is expected that mill speed control will soon be a regular feature of plant operation2,6."

Jan 1, 1985