Search Documents

By Robert M. Vadas

Special considerations are described as they apply to the design of ring gears for high-power grinding mills. AGMA requirements, the importance of the supporting structure, material selection and related field experience are discussed, with special emphasis on available and developing manufacturing technologies.

Jan 1, 1978

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

By R. H. Chambers, L. Alderman

"The paper is introduced by an examination of the factors which have led to the present world-wide interest in charging preheated coal to coke ovens. Various possible methods of preheating and charging the coal are considered and reasons are given for the adoption of the methods chosen. The design of the pilot preheating plant for the British Coke Research Association is discussed and its influence on the design of the commercial units for the South African Iron and Steel Corporation's plant at Pretoria and the British Steel Corporation's plant at Beighton are explained. Operating procedures on the pilot plant are described, particularly with regard to the charging of the preheated coal. Design features of the commercial installations, engineered by Simon-Carves Ltd., are explained with emphasis on the built-in safety of the control system of the preheating plant, and the particular problems associated with the erection of such plants on working coke oven batteries. Commissioning and operating procedures are described and the problems associated with the integration of the preheating plant into the normal pushing schedule of the plant are discussed. Preliminary operating results with regard to the effect of preheating on coal throughput on the commercial plants and on the properties of the coke produced are given."

Jan 1, 1972

By Joseph J. Larry

In hard siliceous sandstone strata overlying coal seams, roof bolting is often the bottleneck in the coal production cycle. In the past, these strata have been drilled by pneumatically operated stopers. Although slow drilling is cumbersome and uncomfortably noisy, the stoper was the most effective drill in these harder strata. However, because of the (U.S.) Coal Mining Safety Act, which limits noise levels for operating drills, FMC Mining Equipment developed the water-through-the-drill-steel method of drilling high-compressive-strength strata. Although water-through-the-drill steel had been developed earlier, the real impact of wet drilling techniques surfaced when the dual-boom roof drilling machines were installed at the Virginia-Pocahontas Division, Keen Mountain, Virginia, in 1974. This paper covers some of the technical details of the water-through- the-drill-steel design and its application.

Jan 1, 1979

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By R. White, C. Doyle, B. Martin, C. Díaz, J. Hrepic, G. Cuthbert

"A program initiated to improve the service life of the magnesite-chrome refractory in the top blown rotary converters at INCO’s Copper Cliff Nickel Refinery identified slag corrosion as a major wear mechanism. Target slag compositions were established to produce a non corrosive slag. A plant program to achieve this target slag by the addition of controlled amounts of do lime and MgO was instituted. Addition to rates of the slag modifiers was optimized based on the slag composition assays achieved and the requirement to address corrosion effects on the high alumina content ladle refractory. A60% gain in TBRC refractory performance was eventually achieved and has been maintained yielding a net annual savings of $700,000. A significant gain in available converter operating time has also been realized.IntroductionINCO’s Copper Cliff Nickel Refinery utilizes two top blown rotary converters (Fig. 1) to smelt a blend of semi-refined nickel concentrates, producing a granulated nickel matte suitable for the adjacent carbonyl based nickel refining operation. The converter, or TBRC, operation is a batch process composed of feed charging and melting, oxidation of the excess sulphur in the matte, and reduction of residual nickel oxide. The final matte, containing about 78% nickel, is tapped at 1600°C from the converter and is granulated in a sluice equipped with high pressure water jets."

Jan 1, 1997

By Lionel A. York

THE first application of the cementation process took place in the year 1864, according to H. Standish Ball, when a break in the brickwork lining at a depth of 270', in one of the Rhine Preussen pits near Homburg, was sealed by running in milk of cement from the surface by means of a small hand pump. At about the same time Monsieur Portier adopted the method in France for repairing breaks in shaft lining. Figure 1 is descriptive of the Portier system and is of interest when compared with modern practice. During the next thirty years numerous attempts were made to improve the process; the general method used in sinking being to put clown bore holes outside the perimeter of the shaft for the purposes of injection. The cementation process was first recognized as an important as-set to mining in 1896 when Monsieur A. Francois developed his method of boring and injecting inside the shaft below the permanent water level. The Francois cementation process rapidly attained fame on the Continent and many shafts were sunk by its use in France, Belgium and

Jan 1, 1961

By Ryan L. Veenstra

This paper presents a modelling study of a cemented paste backfill in an underground stope. The model was developed to help provide a better understanding of what is happening in the stope during the filling stage of the stope. In order to do this, the model incorporates the paste rise rate, stope geometry, and time-dependent input parameters. This paper looks at the effect of geometry in two parts. The first part compares a series of simple rectangular stope models. These models differ in size both in two and three dimensions. The second part compares the results of four 2D models together and then to the field instrumentation data. Part of this section introduces the geometry and instrumentation within the test stope.

Jun 1, 2012

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By S. Sundararajan, Z. Lin

ABSTRACT Fierce market competition and demand have made it imperative for mining companies to achieve higher productivity and operational efficiency. The selection of the best mining method and equipment combinations will enable companies to meet production and efficiency targets. Continuous mining is increasingly preferred by companies for its high efficiency and low unit costs. We developed simulation models for two continuous mining systems: the continuous surface miner (CSM) system and the at-face slurrying (AFS) system. Considering two different case studies, the paper discusses application of developed models to determine the optimal number of trucks and equipment capacities for the two systems.

Jan 1, 2013

By J. H. H. Chamberlin

"In the Introduction the author briefly discusses the company history as it relates to the development of its contracts with the Japanese steel mills. The main part of the text describes how Coleman Collieries Limited approached the problem of mining coal profitably in thick, steeply inclined seams. For many years a basic room-andpillar system was worked by conventional methods. Main roadways were driven on strike across the mineable area. These roadways acted as haulage routes for coal, materials and men. Rooms were developed to the rise of the main haulage route by pairs of men using air-operated hand picks. As these rooms advanced the miners would lay and extend a sheetiron chute down which mined coal would gravitate to a controlled loading point, where it was loaded into trains of mine cars. Connecting roadways or ""OFFS"" were driven at predetermined intervals between adjacent rooms, forming pil1ars or blocks. Extraction of the blocks followed on a line conducive to good strata control some distance behind the developing rooms. A need for higher productivity, expansion of the operations and a scarcity of qualified miners resulted in the company deciding to mechanize its underground mines. Joy 6 CM continuous miners and 10 SC shuttle cars were selected as being machines that could reasonably negotiate the problems associated with the pitching seam. The equipment, nonetheless, has definite limitations and Coleman therefore developed a modified version of the room-and-pi11ar system such that the miners and cars could work on cross pitch. In the area described, main roadways were driven to the rise on an average gradient of 12 degrees. Panels, which consisted of two parallel roads with interconnecting cross-cuts, were then developed on strike to a boundary point. Blocks formed in the development of the panels were subsequently extracted on retreat. Problems associated with each phase of the operation are thoroughly discussed, together with roadway support methods and equipment used for the conveyance of coal and materials."

Jan 1, 1972

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By N. R. Andrade-Gonzalez

The present work was performed on four alloys containing Al-6 2 wt pct Si-3 5 wt pet Cu, with magnesium in the range of 0.02-0 40 wt pct, and strontium in the range of 0-165 p p m Tensile bars were cast in a permanent mold (ASTM B108-160) and heat treated at 495°C for 4 hours, followed by quenching in hot water. Two different artificial aging temperatures were applied at 180 °C and 220 °C for times from 0 5 h up to 8 h Tests were conducted with the intent of determining how the mechanical properties of an aluminum-based 319 alloy are affected when aging time and temperatures are varied In general, it is seen that the alloy does not exhibit the common peak-overaged aging condition due to the presence of several coexisting phases, indicating that they form through complex eutectic reactions late in solidification.

Jan 1, 2004

By Vahid Faghihi

SatraPM is a web-based software package, aiming to help project managers to easily handle their construction projects via internet. This software is capable of handling all projects of an organization, in which all projects can be defined in EPS the same as users in OBS. A 3D accessing module links EPS, OBS and inherent functions in order to provide a secure environment for the data to be processed throughout the system. This paper intends to take a deeper look at capabilities of SatraPM in helping project managers to keep track of and control their construction projects as well as its potential future features.

Aug 1, 2013

By J. A. Drozdiak

In this paper we examine, through pilot-scale testing, the possibility of operating a circuit comprised of two stages of HPGR comminution, followed by grinding through a horizontal stirred mill. In order to assess whether the novel circuit design could achieve the reduced energy requirements indicated in the literature, two more-established circuits, a cone crusher / ball mill and an HPGR / ball mill, were examined using a combination of testing and flowsheet simulation. The results showed that, based solely on the specific energy requirements for comminution, the HPGR / stirred mill circuit achieved a reduction of 9.2% and 16.7% over the HPGR / ball mill and cone crusher / ball mill circuits, respectively.

Jan 1, 2012

By R. Duinker

"This paper, an update to the 2003 paper titled "Knowledge, Technology and Profit" (Twigge-Molecey, 2003) analyzes 45 "problem projects" from the mining and metals industry over the last eleven years representing $133 billion in CAPEX. The projects have been designated as "problem projects" as they did not meet their owner’s initial expectations for project performance as defined in the paper. This paper explores some of the challenges that were present, through interviews with the knowledgeable individuals that were familiar with the projects and investigations using publically available information. The aim of the exercise was to identify the key challenges faced by the projects, and the contributing factors that led to the project failures so that the lessons can be applied to future projects.The project challenges have been categorized into four themes, technical, organizational, environmental & social and missing "homework" prior to board approval. Of noteworthy interest is that environmental permitting aspects have risen to become a significant and notable contributor to problem projects in 11 years from 2003 to 2014. It is further observed that many projects have been challenged by increasing size and complexity and with execution in more remote locations since the previous paper.It is a reality that every project will face challenges. Some projects are simply more challenging than others, and success or failure of the project is often determined by whether the project team is fully prepared to respond to the challenges. This in turn is largely dependent on whether the project "homework" was adequately completed and considered for all aspects of the project."

Jan 1, 2015

By E. O. T. Simpson

"IntroductionAS COMPARED with coal mines in the United States, and even with some of those in eastern Canada, the coal mines of western Canada, generally speaking, :have made little progress toward mechanization at the working faces. So far as Vancouver island is concerned, there are three main reasons for this : ( 1 ) in some areas, conditions• easy for hand-loading but unsuitable for mechanical loading make high outputs per man •possible by the former method; (2) faulting of the coal seams in ..some areas precludes long-term planning and the introduction and efficient use of expensive equipment; (3) thinness •and other characteristics of the seams in many areas favour hand-loading.No. 8 MINENo. 8 mine of Canadian Collieries (Dunsmuir), Limited, is located in the Cumberland sub-area of the Comox coalfield on Vancouver island about 90 miles west-northwest of Vancouver. The geological structure of this coalfield has been described by J. D. McKenzie. The seams occur in the Comox formation, a subdivision of the Upper Cretaceous Nanaimo Group. The formation is of near-shore origin and was laid down on an irregular surface of' older rocks. The irregular generally have a northeasterly dip, modified by gentile folds and by a •few large, and a number of smaller, faults.Four seams have been worked in the Cumberland area and all vary in thickness and in the amount and number of interstratified bone and rock •bands."

Jan 1, 1953

By Richard N. Zimmer

This paper discusses the installation of corrugated steel linings in bored raises at Inco's Thompson Mine. The procedure for the installation of these linings is outlined and the relative advantages are compared with conventional methods of ground support. Future trends in the use of corrugated steel products are then discussed.

Jan 1, 1978

By David J. Forrester

"CANMET’s research into underground coal mining is primarily conducted at the Cape Breton Coal Research Laboratory (CBCRL), established in 1981 to conduct safety research in underground coal mines. Located close to Canada’s largest underground coal producer, in the Sydney Coalfield of Nova Scotia, CBCRL’s program also includes the two western underground coal operations. CBCRL is a relatively small laboratory with a staff of thirteen — eight professionals and five support staff — with an annual budget of over $1 million. In order to maintain effective research response, flexibility is key and staff are increasingly working in project teams, crossing traditional section ties and also drawing from specialist expertise elsewhere within CANMET.CBCRL’s research activities have had a substantial impact on the Canadian underground coal mining industry, particularly in Cape Breton. CBCRL contributed to Cape Breton Development Corporation’s (CBDC’s) threefold reduction in lost-time accidents in the 1980s. Also, in the last four years alone, CBCRL’s work has enabled CBDC to save over $17 million in improved utilisation of reserves and cost savings. The work embraces the three traditional areas of mine environment, strata mechanics and mining technologies, however the current direction has been strongly influenced by recent external and internal factors. It is timely to review progress and recent directions."

Jan 1, 1996