Search Documents

By M. Kolahdoozan, H. Noori

"Molybdenite flotation at the Sarcheshmeh Copper Complex has been studied as a function of pulp potential controlled using two types of sodium sulfide (mineral and chemical origin). Air and either plant or laboratory nitrogen was used as a flotation carrier. Potential measurements were taken in the rougher cells as it was proved to be vital for molybdenite flotation. Flotation test with reducing potentials between -525 and -575 mv gave the highest molybdenum recovery (93%) and the lowest copper recovery of between 4 to 15% can be achieved. These potentials did not change considerably by adding increasing amounts of sodium sulfide. At more oxidizing potentials, i.e. more than -450 mv, the recovery of copper increases while the recovery of Molybdenite drops.INTRODUCTIONThe average copper ore feed grade to the Sarcheshmeh flotation circuit is typically set at about 1.2% Cu. to be delivered to processing unit is set at 1.2%. There is no control of molybdenum (Mo) which usually varies between 0.01 and 0.04%. During concentration, a Cu-Mo concentrate is produced by one stage of roughing, one stage of scavenging and two stages of cleaning. Final concentrate contains 0.5% of Mo and 32% of Cu while the particle size is 90% under 42 microns (325 mesh). Because of the high grade of Mo in this concentrate and economic interests, a molybdenite flotation circuit plant was built in 1984. This plant was designed to treat 1432 tons of Cu-Mo concentrate (on dry basis) and consists of one stage of roughing followed by seven stages of cleaning. After dewatering the concentrate contains 53.7% Mo which is dried and shipped overseas.The majority of molybdenite production worldwide comes as byproduct of copper porphyry ores. The Mo grade typically varies between 0.01 and 0.06% and accompanies chalcopyrite and chalcocite. Due to the hydrophobic nature of molybdenite, it can be floated along with copper sulfides. Thus the overall concentrate of Cu and Mo contains 0.2-1% of molybdenum as well as 20-42% of copper. To separate the Mo, Cu and Fe minerals, depressants are used. The most important of which are sodium sulfide, sodium hydrosulfide, Anomal D, sodium cyanide, ferropottasium and ferro-cyanide. The first three regeants have been extensively used for successfully treating porphyry ores [1]. In the molybdenum plant of the Sarcheshmeh Copper Complex only sodium sulfide has been used to date."

Jan 1, 2006

By A. Coulombe

"RésuméL’analyse des séquences d’exploitation, actuellement en usage pour les gisements très inclinés, a démontré qu’elles ne sont pas toujours optimales du point de vue du contrôle des terrains et de la concentration des travaux d’abattage (nombre de chantiers simultanément en opération). Effectivement plusieurs séquences sont très propices à la création des nombreuses zones de hautes contraintes, qui sont à l’origine des effets de pilier. L’étude de cas de la mine Lac Shortt a démontré que certaines séquences d’exploitation, actuellement en usage, ne sont surtout pas adéquates dans le cas d’un état élevé des contraintes naturelles. En effet la mine a eu de sérieuses problèmes avec le contrôle des terrains (coups de terrains et les effondrements des épontes). Ces effondrements étaient responsables de la dilution excessive et des pertes importantes des réserves minières. Les deux nouvelles séquences proposées, visent la meilleure redistribution des contraintes d’exploitation en vue d’éliminer la création des effets de pilier. En plus elles permettent une concentration plus élevée des travaux d’abattage.À notre avis les séquences proposées pourraient améliorer substantiellement la stabilité des chantiers d’abattage et par la suite les performances technique et économique des opérations souterraines. ABSTRACTThe planning of underground mining sequences represents an important aspect of the mining operation. The analysis of mining sequences actually in use for very steep orebodies has demonstrated that they are not always optimal, considering ground control and the number of stopes simultaneously in extraction. These sequences are conducive to the creation in the rockmass of several stressed zones caused by pillar effects. The case study of Lac Shortt mine showed that the sequences of exploitation currently in use are not adequate especially in the case of a high state of the natural constraints. Indeed, the mine had serious problems with ground control (rock bursts and collapse of walls). These collapses were responsible for excessive dilution and significant losses of mining reserves. The two new sequences suggested aim for the best redistribution of exploitation constraints in order to eliminate creation of pillar effects. Moreover, they allow a higher number of stopes to be extracted simultaneously. In the opinion of the authors, the sequences suggested could substantially improve the stability of working areas and, thereafter, technical and economical performances of the underground operations."

Jan 1, 1998

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By J. W. Reynolds

This paper describes the function of the research and development department of a large mining organization and the benefits which can be derived over the years. Examples are given of work done in rock drilling, ventilation, noise control and the development of backfill stowing machinery.

Jan 1, 1970

By Daniel Murray

"ACCIDENT PREVENTION in and around coal mines presents many problems of a type which are not encountered in any other industry. This is particularly true of the coal mines in Nova Scotia, where the underground workings are very extensive and the area of exposure to workmen is very great.Roof conditions at the coal faces and in the waste change very rapidly, almost from hour to hour, and it is at these places that the greatest dangers exist and where most mine accidents occur. It is only natural, therefore, that our attention, as far as accident prevention is concerned, should be concentrated •at the coal faces and in the waste, especially in mines where the longwall system is used in the operation •of the seam.It has been said that no hard and fast rules can be set down for timbering at the coal faces and in the waste in the coal mines in this area. We do not subscribe to this theory, however, for the following reasons:On the longwall faces in No. 18 Colliery of the Dominion Coal Company, Limited, where the 'Dosco Miner' has been in operation and where there is a very rigid system of timbering and roof supports, which is strictly followed, only one compensable accident has occurred on those faces from May 2ndJ 1950, to the time of writing this paper, February 3rd, 1953.The 'Dosco Miner' has worked on four different longwall faces in this mine and has mined and loaded some hundreds of thousands of tons of coal."

Jan 1, 1953

By D. Sbarbaro

In many modem concentrators the use of supervisory systems in their grinding circuits has meant more consistent operations and increases in capacity. These systems rely on a series of specific algorithms that uses different pieces of information and drives actions over the process. One of these algorithms is the ball mill overload detection, which plays an important role in any supervisory strategy designed to maximize ore feed rate in wet grinding circuits. This paper introduces different overload detection algorithms, and compares them in terms of the time taken to detect the overload condition. This comparative analysis is based on highly noisy power draw measurements obtained in an industrial plant.

Jan 1, 2007

By Norman B. Davis

Introductory Feldspar is one of the most important mineral products consumed by the various branches of the ceramic industry. In the manufacture of table ware, electric porcelain, floor tile, and enamels, it supplies the chief fluxing ingredients necessary to bond the other more or less inert materials together when moulded into desired shape and fired in a kiln. Feldspar is used in the manufacture of bottle glass as a means of introducing alumina in a form easily assimilated. It is also used in certain scouring soaps particularly designed for cleaning enamel and glass surfaces. Feldspar, as it finds its way to the trade, is not a single mineral but is rather a mixture of various proportions of the feldspar silicate series, either in natural intergrowth or blended in the milling process, to produce a desired result. It is often further modified by the presence of quartz in amounts up to 30 per cent. The table on the next page gives typical commercial analyses of feldspar from various sources. Canadian feldspar produced to date has consisted mainly of the high-potash, relatively low-soda, variety, and has enjoyed a good market in the United States for the manufacture of enamels, electric porcelain, and vitrified table-ware. About eighty per cent of the output has been exported to the United States, but, with increased milling facilities in Canada and changes taking place in domestic United States sources of supply, the proportion exported will be reduced next year.

Jan 1, 1931

By Leslie S. Weldon

THE Lake Shore mine has been developed by two vertical shafts, with level intervals at 200 feet to the 2200 level and at 125 feet below this horizon. A main cross-cut joins the two shafts on all levels to the bottom of No. 3 shaft, and opening into these cross-cuts are the ore passes and sand passes, which are completed from surface To the 4450 level. In the west part of the mine, additional connections have been made between No. 1 and No. 2 veins, through which the major part of the ore from No. 2 vein west is routed to drifts in No. 1 vein. With the lesser amount of stoping on No. 1 vein, this arrangement permits better haulage to be maintained. The ore passes are driven at 50 degrees from the ends of short cross-cuts off the main ones and are broken through to the levels above at the mouths of the short cross-cuts, to allow for dumping on each level. The passes are controlled at each level by ball-and-chain gates and deliver to crushers and thence to loading pockets, shown in Figure 1. That system is quite flexible in that it is possible to by-pass the crushers at any station and load from either shaft at a number of different pockets. The sand passes are driven from the main cross-cuts at the same inclination as, and parallel to, the ore passes. Each is equipped with a chute and dump hole, so that waste or sand fill may be loaded or dumped at each level. A transfer door, hinged on the bottom, is installed opposite the chute for by-passing fill from one level to the next, and in the closed position protects the opening at the top of the pass. The dump hole situated beside the transfer door is protected by a grizzly with 10-inch spaces. Waste rock may be withdrawn from the system through No. 3 shaft loading pocket at the 2950 level to a waste bin on surface. Levels are developed by drifts in No. 1 and No. 2 veins for their entire lengths. Subsidiary breaks are followed at a later date, when full information has been obtained by exploration, and a considerable amount of development by sub-drifts is carried out in the upper part of the mine, particularly in more or less erratic sections of No. 1 vein.

Jan 1, 1936

By A. Zangooi, J. A. Finch

Flotation is a separation process based on the collection of particles on the surface of bubbles. Flotation machines disperse air into bubbles using a variety of techniques. The characteristics of the bubble population are strongly affected by the selection of frother type and concentration. As metallurgical results depend on the bubble distribution, the measurement of frother concentration is vital to understand and control performance. A previously developed colorimetric technique was refined to work with low solubility frothers and to increase daily analysis rate. Field-testing demonstrated that the method is robust, reliable and accurate. As well as relating frother concentration to gas dispersion measurements, the results can be used to answer operational questions including: how well a frother dissolves, how reliable and stable frother delivery is, how evenly frother is distributed down a bank, and whether frother distributes between the pulp and froth zones. Some of these points are illustrated from plant experiences. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By A. G. Slade

"This paper deals with the direct application of rock mechanics in the underground mines at the Sudbury Operations of Falconbridge Nickel Mines Ltd. It covers mining methods, the use of photoelastic models, the fore-casting of rock strains and their elimination, closure methods and other common methods of ground control.INTRODUCTIONROCK MECHANICS IS A STUDY IN ROCK BEHAVIOUR and, although it is being termed a new science, it has been practiced since the industry began. Every person involved with rock excavations, from the mine superintendent to the stope driller, is actually practising rock mechanics. They probably call it by another name -experience, and applications of this knowledge are in evidence throughout the Falconbridge operations. Only in recent years have formal rock mechanics studies been employed to provide technical assistance to the mine operators in their primary objective of producing ore safely."

Jan 1, 1968

By Solar D. Andrés

Several large open pit mines are facing the challenge to design and plan an underground transition to sustain the long term future of their operations. The desired underground method is Block Cave since its natural high productivity and low operating cost that could compete against the open pit cost to mine the final open pit pushbacks. It has been found at several operations where this transition is taking place that the pit limit at which transition is performed is rather deep. This aims to think that perhaps several transition projects have started late in the life of an operation producing an over stress in the transition project and reducing the flexibility in the design of the overall infrastructure and a substantial lost in the complete project NPV. Traditionally the approach to plan open pit underground transition consists of sequentially deciding the final pit using a Lerchs and Grossman type of optimization to find the overall maximum pit shell and then running block cave simulations to find the best footprint for the underground option. The research summarized in this paper is related to the development of an integer linear programming model that aims to compute simultaneously the maximum NPV of the combined option final limit open pit and block cave underground footprint. The model has been tested using two large block models representing two of the current operations in the process of transiting from open pit to underground operations. Finally, the integrated open pit underground transition model is going to be compared to the traditional sequential approach in order to define which method achieves the best NPV. The paper illustrates both case studies in depth.

Oct 1, 2009

By J. D. Bateman

Introduction The lifting of restrictions on the development of radioactive mineral deposits by private individuals has re-opened the search for uranium in Canada to a large body of professionally trained prospectors. The entry of private capital and experienced prospecting techniques into the search for radioactive minerals has been enormously stimulated by the atomic developments of the past several years; and we can now look forward to the discovery of new productive sources of uranium. The rate of new discoveries will, how ?ever, depend on the effectiveness of the methods used. The large number of new pitchblende occurrences reported within the past several months is largely a measure of the energy with which the portable Geiger-Müller counter has been applied in the field. The counter is simply a 'radio' receiver tuned to one of the products of spontaneous atomic disintegration that is characteristic of all radioactive materials. Its effective use depends largely on how it is applied under the various geological and topographical conditions that ma y be encountered, and also on an understanding of its limitations. Extensive geological information relating to the occurrence of radioactive minerals in Canada has been accumulated during the past several years, and it is now possible to define in a general way many of the geological formations in which pitchblende and related minerals are likely to occur. Furthermore, prospecting can be localized in those parts of the favourable formations that offer the greater promise of containing commercial deposits. In this selection, the Geiger counter is the most useful tool available to the prospector for the actual detection of radioactive materials. As an example, an area of two square miles in the Northwest Territories, within which about a dozen pitchblende occurrences had been found over a several year period by conventional prospecting methods, yielded more than forty-five additional discoveries by application of the Geiger counter. Yet earlier attempts at prospecting this area with the counter had failed, due largely to faulty instruments and lack of experience in field application. The limitations of the counter are very considerable; but, when they are recognized, there is no more useful tool for the discovery of radioactive ores. It was not until 1944 that a practicable portable counter was developed, and then only by co-operation in the field by geologists and physicists. Officers of the Geological Survey of Canada working with physicists of the National Research Council brought about the development of the modern counter.

Jan 1, 1949

By F. Flynn, P. Downey, G. Ritson

"Bell Creek Mill which has been in continuous operation since 1987 has undergone numerous operational changes in the past three years. The addition of over 2. 5 million tons of resource at over 13 git from Hoyle Pond Mine precipitated an expansion program for the Bell Creek Mill. This paper discusses the major changes that have occurred over the past two years to increase throughput and efficiencies. In addition, the refractory ore treatment options are also discussed.IntroductionThe Bell Creek Mill is located in the Timmins Goldcamp approximately 8km NE of porcupine Ontario. (Fig I.)The mill was originally constructed by Camamax in 1987 to treat the Bell Creek ore at a design throughput of 350tpd. The flowsheet (Fig 2.) consisted of two stage crushing, grinding, thickening, leach and drum filtration with gold recovery by Merrill Crowe.As ore depleted at Bell Creek, the Mill was purchased by Falconbridge to process ore from their Hoyle Pond property. Kinross purchased the Hoyle Pond property and Bell Creek Mill from Falconbridge in 1992.The successful exploration program at Hoyle Pond has led to several expansions and process design changes, with further changes planned over the next twelve months.In 1994, the mine produced 61,865 oz. of gold at an average cost of 197US$ per oz. In 1995 production was 91, 611 oz. at a cost of 187US$ per oz. Projecting the nine months ended September 30, production for 1996 will be 155,000 oz. at a cost of 165US$ per oz.In early 1997, the CIP expansion will be complete, with a target of 175,000 oz. at a cost of 176US$ per oz for 1997. The mill throughput will have increased from 400tpd to 1500tpd between 1994 and 1997.The changes to Bell Creek since 1994 have been numerous with very little of the existing equipment still in operation. The total cost of the expansion to date is 15 million C$. This paper discusses the major projects carried out during in this time. The focus will be to highlight the justification of each project, the design and engineering, some of the initial start-up problems and solutions.Figure 3 shows a plan of the existing mill facility together with the various additions that were carried out."

Jan 1, 1997

By A. Manohar Rao

Underground mining in general and more so the coal mining is a hazardous venture as it is a struggle against nature and natural forces. The stability of roadways has a direct impact on production and productivity. The roadway stability can be strongly influenced by the direction of the drivage. The stress studies are useful to provide a frame work for understanding the influence of drivage direction on roadway conditions, and to illustrate how mapping techniques can enhance this understanding. The act of mining can concentrate and re-orient the original stresses. Whenever coal is removed, the overburden weight that it carried is transferred. Vertical stresses are similarly affected when the roof is deformed or failed. The Singareni Collieries Company Ltd., a joint Public sector undertaking of the Government of Andhra Pradesh and India is conducting coalmining operations in the Godavari Valley Coalfield and is catering to the needs of a large part of South India. With the technology update, it is looking for safe mining and to achieve higher production. As a part of this, an attempt is made to understand the stress conditions prevailing on the mine blocks by different ways and means in terms of geology, structure and tectonics of the Godavari Valley coalfield, satellite imagery studies, cleat pattern, stress measurement studies conducted in different mine blocks, and stress mapping technique.

Aug 1, 2013

By K. Soucek, J. Ptácek, A. Hastíková, R. Kukutsch, P. Konícek, P. Waclawik

"Cable bolts are used frequently as a secondary support system (with steel arch support) in difficult stress-strain conditions of deep coal mines. The load transfer mechanism of cable bolts depends on several factors, such as the strength, deformation and geometric properties of the bolts, resin and the surrounding rock mass so-called cable-resin-rock system (CRR system). The bonding length and bolt/borehole diameter ratio strongly influence the final bearing capacity of the CRR system.The study presents the behaviour of CRR system during a pull-out test which is usually used in the carboniferous rock mass in the Czech part of the Upper Silesian Coal Basin. A series of 28 pull out tests were performed on 3-m-long cable bolts, with various combinations of borehole diameters and bonding lengths, to understand this behaviour. Boreholes were drilled into a solid rock mass consisting of fine-grained sandstone to guarantee similar conditions during the pull-out tests. Video inspection and measurement of borehole diameters were performed to determine their quality and real diameters. Three characteristics were observed from pull-out test results: ultimate pull-out load; displacement of the end of bolt and system stiffness. Numerical modelling by FEM (Finite Element Method) was used to determine the stiffness of the CRR system for variable bolt/borehole ratios and bonding lengths each under constant load. A linear elasto-plastic model and a mohr-coulomb model were used for cable and resin-rock respectively. The results of the experiment may contribute significantly to improving of the methodology of cable bolts installation as well as the design of used cable bolts."

Jan 1, 2015

By T. W. Wloder

During recent studies concerning the effects that various surface treatments, surface imperfections, locked-in residual stresses and metallurgical and geometrical notches have upon the mechanical behaviour of metals and, in particular, upon their tension-bending characteristics under impact loads, it became apparent that specially developed methods and samples would be of great assistance in determining the desired data. This paper describes and discusses a number of different types of double-notched tension-bending impact samples which have been considered and examined for this purpose. The types most suitable for exploratory investigations are proposed for application in the study of the _behaviour of metals, their welds, and, in particular, their surfaces, when subjected to various notch-severities, surface imperfections, strain rates, temperatures, and constrained states of stress (i.e. the relations of the three principal stresses). It is expected that the proposed double-notched tension-bending samples and the proposed test methods will also contribute toward further understanding of the cold brittle behaviour and the notch-sensitivities of metals. The possibilities of introducing the so-called impact notch-sensitivity index and relative impact notch sensitivity of metals are discussed. Data obtained on double-

Jan 1, 1961

By R. S. Boorman, L. J. Surges

"Ore reserves at Brunswick Mining and Smelting totalled 101(106) tonnes grading 97 grams tonne-1 silver at the end of 1981. Silver is recovered as a byproduct in the copper, lead and bulk concentrates and is lost to the zinc concentrate and plant tailings. Recovery of silver for the year 1981 was 58,5%. The loss of potential revenue is in excess of Cdn $50(106) year-1 at current silver prices and milling rates.Silver is known to occur in solid solution in galena and as tetrshedrite. Evidence indicating the identity and significance of a third silverbearing mineral assemblage is reviewed and the distribution of silver losses is detailed. Characteristics of each the carrier which may be responsible for observed distribution, including size, surface quality, liberation and composition are considered, and the third carrier is shown to have possible implications for improved silver recovery by other Canadian producers as well as by Brunswick Mining.Silver tetrahedrite tailings distributed tailings and losses occur as coarse, free and as very fine unliberated galena in losses of the third carrier are between the zinc concentrate and are concentrated in the finest size fractions. Process alternatives for enhanced silver recovery by physical and chemical means are reviewed."

Jan 1, 1983

By John H. Schloen

"The object of this paper is to review electrolytic copper refining as it was in 1954(1), as it is now in 1984, and to comment on the many improvements which have been made in the last thirty years.In 1954, and even in 1984, the ASTM specification B 115 for cathode copper was 99.90% minimum copper plus silver content and 100% minimum electrical conductivity, IACS standard. However, to meet competition and to satisfy the requirements of the fabricators and the electrical industry, the electrolytic refinery must supply a product of 99.95% to 99.96% minimum copper content, and 101fJlo minimum electrical conductivity.The range of cathode impurities reported by 20 major copper refineries in 1954 are given in Table I.The much more rigid British Specification, DD 78, for high-purity cathode copper, specifies individual elements, as well as groups of elements, as shown in Table 2.The Svenska test has been replaced by a similar procedure which uses 2.r mm diameter wire. The ISO test is the one listed in the DD 78 specification. In Table 3, corresponding values for the Svenska and ISO test s are given for various wire bar coppers."

Jan 1, 1986