Search Documents

By Q. F. Wang, M. H. Lai, T. Q. Liu, G. G. Dong

Compared with the traditional pre-treatment process, biological oxidation process has many advantages including higher gold recovery, less cost, easier operation. The bio-oxidation reactor is the most important equipment for biological oxidation process. In this paper, the characteristics of biological oxidation are investigated, and the design principles are proposed based on laboratory tests. Both increasing the tank height and taking new inflation system can enhance higher dissolved oxygen. The new type of large-scale industrial bio-oxidation reactor is designed, which is 9.5 m in diameter and 10 m in height. The bio-oxidation reactor metallurgical performance has been tested by industrial-scale experiment. The slurry of flotation concentrate is divided into two parts to feed two bio-oxidation reactors. The feeding rates of two reactors are adjusted on the basis of getting the same content of S, Fe, As in overflow. The result shows that the feeding rate of the new type of 700 m3 bio-oxidation reactor is 3.72 m3 per hour, and the feed rate of the conventional 700 m3 bio-oxidation reactor was 3.23 m3 per hour. The processing capacity of the former is 15.2% higher than that of the later, which demonstrates the new type of bio-oxidation reactor has higher oxidation rate.

Jan 1, 2015

By John F. Kearney

Labrador Iron Mines (?LIM?) Schefferville Projects consist of 20 major DSO deposits lying along a 120 km strike length in both the provinces of Newfoundland and Labrador and in Quebec. The town of Schefferville, Quebec lies close to the middle of this 120 km strike. LIM?s various properties comprise twenty different iron ore deposits which were part of the original Iron Ore Company of Canada (?IOC?) direct shipping Schefferville operations conducted from 1954 to 1982 and formed part of the 250 million tons of historical reserves and resources previously identified by IOC. LIM intends to develop all these resources in five separate stages. The first four stages will see the various deposits treated in three beneficiation plants, to be built adjacent to several of the deposits that comprise the Central, South Central and North Central Zones. The final stage is not yet planned but will likely involve a fourth plant. A Feasibility Study has not been completed on any of these Projects. LIM plans the development and mining of the various deposits in separate Stages. It should be noted that only the James and Redmond deposits have been permitted. All other deposits require environmental assessment and permitting. Only the James and Redmond deposits have been subject to detailed mine design. The Houston deposit has had preliminary mine design carried out. All other deposits will require detailed mine design when further geological data is collected and compiled. Detailed metallurgical testwork has been carried out on blue ore from James, Houston, Redmond and Knob deposits and to a more limited extent on yellow and red ores from these deposits. Only limited review work has been carried out on the high-silica blue ores. All of this work will be needed to be complete to confirm the final process routes. Additionally some metallurgical work will be required to be conducted on each of the other deposits to characterize their metallurgical response and to confirm expected recovery levels. Detailed mine design and metallurgical testwork has been carried out on those deposits that will form the basis of production for the initial years but further exploration, testwork and design is required for all the remaining resources. The first plant at Silver Yards and mine construction at James are now complete and initial production is expected in the spring of 2011. Metallurgical testing of the first stage deposits has established that the ore can be successfully upgraded to marketable standards. Based on the current testwork, a program of plant enhancement on the Silver Yards plant is now planned with the objective to increase both the plant throughput and recovery. Production of direct shipping lump ore and sinter fines is forecast at around 1.5 million tonnes in 2011 and, based on current and historical resources, growing to approximately 5 million tonnes in 2015 and thereafter. Production from the first four stages is expected to continue at about this rate through to about 2028.

May 1, 2011

By T. J. Langan, M. Ramajayam, T. Dorin

"6xxx-series Al alloys are the most commonly used alloys in the automotive industry as they have an appropriate balance of strength, corrosion resistance and formability. The main strengthening phase in these alloys is the ß’-Mg2Si precipitates. One opportunity to achieve stronger 6xxx-series Al alloys, without affecting corrosion and formability, is the use of Sc. The main challenge of using Sc in 6xxx-series lies in the heat treatment, which must be designed to allow for a fine precipitation of both Al3Sc and ß’-Mg2Si. In this work, two model alloys are used, an Al-Sc-Zr and an Al-Mg-Si-Cu-Sc-Zr, to explore the impact of the 6xxx-series key elements (Mg, Si and Cu) on the Al3Sc precipitates. Transmission electron microscopy and atom probe tomography are used to investigate the precipitates present in the microstructure after casting. We find that higher Si content results in the formation of dispersoids upon casting. The average composition of these dispersoids is (Al0.8,Si0.2)3 (Sc0.888,Zr0.024,Mg0.08,Cu0.008). A closer look at the solid solution reveals that most of the Sc and Zr is supersaturated after casting even in the presence of Mg, Si and Cu. We discuss the impact of these results on the design of a suitable heat treatment for 6xxx-series alloys with Sc.INTRODUCTION The most common strategy to strengthen aluminum (Al) alloys is by micro-alloying to form a fine distribution of precipitates (Gladman, 1999). Whilst precipitates enhance the strength, this is often done to the detriment of ductility and corrosion performance (Davis, 1999). The 6xxx-series Al alloys are heavily used in the automotive industry as they offer an appropriate balance of strength, ductility and corrosion resistance (W. S. Miller et al., 2000). The strength increment in these alloys comes from the formation of the ß’–Mg2Si and the quaternary Q’ phase (Chakrabarti & Laughlin, 2004; Polmear, St. John, Nie, & Qian, 2017). One opportunity to achieve stronger 6xxx-series alloys, whilst keeping good balance of corrosion resistance and formability, is the use of small additions of scandium (Sc). Sc is one of the most potent strengtheners in Al alloys (Dorin, Ramajayam, Vahid, & Langan, 2018; Røyset & Ryum, 2005). Most of the strengthening benefits from Sc come from the formation of fine Al3Sc dispersoids. The following strengthening mechanisms apply to Sc: 1) Solid solution strengthening, 2) precipitation hardening, 3) inhibiting recrystallization, 4) assisting nucleation of other strengthening phases (Dorin, Ramajayam, Lamb, & Langan, 2017). As compared to other dispersoid phases, Al3Sc dispersoids have good electrochemical compatibility with Al alloys and hence do not affect their corrosion resistance (Cavanaugh, Birbilis, Buchheit, & Bovard, 2007). The coarsening resistance of Al3Sc is often improved by adding zirconium (Zr), as it forms a Zr rich shell around Al3Sc which prevents Sc from moving across the interface."

Jan 1, 2018

By J. Jerome MacDonald, Stephen B. Flewelling

"In the base metals industry of today, operations required to continuously improve productivity and reduce unit production costs. Consistent with these goals is the improvement of the muck haulage cycle from open stopes with the No. 12 Mine.Existing haulage from open stopes occurs with LHD units experience at Brunswick indicates that LHD units have a higher unit cost per tonne mucked than loader-truck combinations when the haulage exceeds approximately 150 m.The reintroduction of open stoping at Brunswick made existing loader-truck combinations unsuitable. It was recognized that application of recent continuous loading technology could potentially result in significant unit cost savings and productivity increases.A review of the technology resulted in the testing of the Voest Alpine AL60 loader in the open stopes located on the 1000m Le vel. Testing began in January 1988 and finished in late November 1988. The test will provide experience as well as quantified production and maintenenace parameters f or the purpose of quantifying production unit costs and system productivity, ultimately resulting in a decision to further utilize or not utilize the loader as a primarymucking unit at Brunswick .INTRODUCTIONBrunswick Mining and Smelting Corporation Ltd. produces approximately 10500 tonnes per day from the No. 12Mine located 35 km southwest of Bathurst, New Brunswick Mining is the largest (single mine) producer of zinc in the world having mined over 52 million tonnes since 1964. Many years of production still remain with proven and probable reserves in excess of 90 million tonnes. Reserves grade at an average of 3.65% Pb. 8.99070 Zn, 99g/mt Ag and 0.32% Cu . The operation employs 1446 people with approximately 800underground including operations and maintenance staff.In the No. 12 Mine two major mining methods are presently utilized . The primary method is Mechanized Cut and Fill (MCF) accounting for approximately 6500 tonnes per day from four major areas. The remaining 4000 tonnes per day is produced from open stopes with the majority of 2800 tonnes per day being produced by the 1000 level.The 1000Level contains 30 million tonnes segmented into open stope blocks 30 m high, 15m and 30 m on strike , with a transverse width of 10m to 50 m (Fig. I). Stopes are organized on a primary secondary stope arrangement along strike. Primary stopes are undercut and overcut full size with the back fully cablebolted. All stope and lateral development is driven 4.0 m high. All stopes to date are flat bottom (Fig. 2). Primary stopes are filled with cemented rock- fill , secondaries with conventional rockfill, Haulage from the stopes is primarily with 8-yard LHD units ; mucking is approximately 50% conventional and 50% remote. Haul distance to date has averaged approximately 150m with current stope haul distances of approximately 300m. Haulage is presently to a small jaw crusher situated on the 1000 Level. From August 1989on, haulage will be to a set of ore passes feeding to a large gyratory crusher situated on the 1200 Level. Start up of the gyratory crusher corresponds to an increase in tonnage from 1000 Level to 4100 tonnes per day."

Jan 1, 1989

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By D. Perednis

Fuel cells with thin samaria-doped ceria (SDC) electrolyte films deposited onto an anode support using spray pyrolysis were fabricated. The SDC films were deposited onto porous NiO-YSZ substrates at deposition temperatures between 400°C and 450°C. The influence of process parameters such as deposition temperature, flow rate, type of salt and salt concentration on the quality of the film was studied. A smooth dense film was successfully deposited using the precursor cerium ammonium nitrate and samarium nitrate dissolved in butyl carbitol (33.3 vol.%), 2-methoxy-l-propanol (33.3 vol.%), and ethanol (33.3 vol.%) solvent mixture. A deposition rate of 125 nm/h was achieved.

Jan 1, 2005

By R. J. T. Charles

Introduction An apparatus that will measure the surface area of a few of the simple minerals with a high degree of accuracy has been described by J. W. Bell (1). His apparatus consisted essentially of a photometric device that would measure the turbidity of fine particle suspensions. Turbidity, in this case, was considered as a function of surface area. Bell's method of surface area determination seemed to offer possibilities of extension and improvement to the point where it might approach a general method of particle size measurement. Theoretical and Practical Considerations of the Photometric Method In order to illustrate how turbidity may be considered as a function of average particle size, and to indicate the type of results expected from a photometric method of particle size measurement involving turbidity, the following theory may be hypothecated. If a number of particles, considered as spheres of uniform diameter, are placed at random in the path of a beam of light, the following expression, which will give the change in light intensity as a function of the diameter of the particles, the specific gravity of the material, and the weight involved, can be formulated from the Beer-Lambert Law:

Jan 1, 1951

Uranium mining remains controversial in many parts of the world, especially in a post-Fukushima context, and often in areas with significant uranium resources. Although nuclear proponents point to the relatively low carbon intensity of nuclear power compared to fossil fuels, opponents argue that this will be eroded in the future as ore grades decline and energy and greenhouse gas emissions (GGEs) intensity increases as a result. Invariably both sides fail to make use of the increasingly available data reported by existing uranium mines through sustainability reporting ? allowing a comprehensive assessment of recent trends in the energy and GGEs intensity of uranium production, as well as combining this with reported mineral resources to allow more comprehensive modelling of future energy and GGEs intensity. In this study, detailed data is reported for numerous uranium mines around the world, including production, energy and GGEs intensity and reported mineral resources. An important aspect included ? arguably unique and never before published ? is the relationship between ore grade and recovery, which is crucial in future projections of uranium mining. Overall, the paper shows the importance of continuing to improve reporting by the uranium sector as well as the ability to analyse key trends and future projections in energy and GGEs intensity of uranium production.

Aug 1, 2013

By G. H. Montgomery

THE PROPERTY of Aunor Gold Mines, Limited, consists of eleven claims, located in Deloro township, approximately three miles southeast of the town of Timmins. Production began in 1940 and currently the mine is operating at a rate of 485 tons per day. GEOLOGY AND MINE DEVELOPMENT The ore zone at Aunor occurs in altered lavas bounded on either side by soft talc-chlorite schist, locally known as 'soapstone'. The zone has a strike of N.80°E, dips 60° North, and varies in width from 0 to 250 feet. Within this zone the main orebody has a westerly plunge, away from the No. 1 shaft area (Figure 1). The mine is developed by a vertical three-compartment shaft from surface to the 3,082-foot horizon. Working levels are spaced at 125- foot intervals from the 625-foot to the 1,625-foot horizon, from which to tl1e 2,125-foot level the interval is 250 feet.

Jan 1, 1957

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By W. Kempson

"Mining Companies have producing assets in increasingly diverse portions of the world. It is not uncommon that the owner, the design team, the mine contractors and the operators are all based in different countries. While these assets are always subject to the regulatory requirement of those countries there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical items such as tailings dams, vertical shaft systems and autonomous vehicles to highlight a few. The work currently being completed in ISO ensures these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. This paper will discuss the benefits of the international standards, the structure of the teams and working groups who are generating these standards as well as the process by which the standards are generated. This will allow insight into the creation of the standard and will aim to demonstrate the “neutral” and technically strong manner in which the generation of these standards is achieved. In addition, the paper will discuss the standards which have been produced in the last five years as well as the current standards which are in place. The finale will discuss upcoming work and the timelines in which it is anticipated these will be completed. INTRODUCTION Mining Companies have producing assets in increasingly diverse portions of the world. While these assets are always subject to the regulatory requirement of those countries, there have not been international standards available to review and evaluate these assets. This becomes particularly important when considering safety critical areas such as vertical shaft systems, tailings dams and autonomous vehicles to highlight a couple. The work currently being completed in the International Organization for Standardization (ISO) ensure these standards will be available and will be generated by and subscribed to on an international basis, thus removing the potential for patriotic partisanship and ensuring safe and predictable systems are installed. The ISO/TC 82 – Mining was founded in 1955. This was an active committee until it was thought that the standards at the time were adequate and the Technical Committee was put on “Care and Maintenance”. In 2012 countries lobbied ISO to pull this committee from dormancy and restart it, this happened in in the same year."

Jan 1, 2019

By N. A. Beier, R. Amos, Smith. L., C. Atherton, D. R. Barsi, D. Blowes, D. C. Sego

"Waste rock is one of the most abundant materials at mine sites and must be properly characterized and managed to limit acid rock drainage and other harmful byproducts. An experimental waste rock pile—part of the test piles research program—located at the Diavik diamond mine (Northwest Territories, Canada) was deconstructed and sampled to study the spatial variability of material properties. Bulk samples were classified based on the amount of material finer than 4.75 mm. Hydraulic properties of each sample were estimated and particle size distribution analysis was completed. These datasets and classification methods might be used to improve the understanding of hydraulic and geochemical behaviour of the material and to study waste rock at other sites. ¦ KEYWORDS Acid rock drainage (ARD), Material classification, Particle size distribution (PSD), Waste rock RÉSUMÉ Les stériles font partie des matériaux les plus abondants sur les sites miniers et, en tant que tels, doivent être correctement caractérisés et gérés afin de limiter le drainage rocheux acide (DRA) et la pré¬sence d’autres sous-produits nocifs. Dans le cadre du programme Test Piles Research Program, un amas de roches stériles expérimental situé à la mine de diamant Diavik (Territoires du Nord-Ouest, Canada) a été décomposé et mis à l’essai afin d’étudier la variabilité spatiale des propriétés des matériaux. Les échan¬tillons en vrac ont été classés en fonction de la quantité de matériaux plus fins que 4,75 mm. Les propriétés hydrauliques de chaque échantillon ont été estimées et l’analyse de la composition granulométrique effectuée. Ces ensembles de données et méthodes de classement serviront à mieux comprendre le com¬portement hydraulique et géochimique du matériau et à étudier les stériles sur d’autres sites. ¦ MOTS CLÉS classement des matériaux, composition granulométrique, drainage rocheux acide (DRA), stérilesINTRODUCTION Statement of problem The characterization of mine waste rock remains a challenge in active mining sites. The large volume of material and the large size of particles make it difficult to collect representative samples. Sampling techniques are often dis-ruptive to mining operations because they alter the structure of the waste rock pile or interfere with mine traffic. The convention at most mine sites to collect little to no information on waste rock material means that models and predictions of how waste material will behave and interact with the surrounding environment are based on general information that might not be site specific. This could lead to environmental damage or higher costs if environmental effects are underestimated during the construction of waste rock structures."

Jan 1, 2019

By Dan Currie, Tom Lamb, J. Coady Marsh, Gary Landry

"This paper describes the Cape Breton Development Corporation's experience with the Lovat M-300 tunnel-boring machine at the Donkin-Morien Mine. Between January 3 and December 21, 1984, the 7.6 m (25 It) diameter TBM advanced 3350 m (10 990 ft) . The authors will describe experiences with the machine and highlight the implications of tunnelling machines to underground coal mine development in Canada. IntroductionThe Cape Breton Development Corporation (CBDC) has recently completed the drivage of a 7.6 m (25 ft) diameter tunnel, 3.5 km (2.2 miles) in length , to access the Harbour Coal Seam at the Donkin-Morien Project. The tunnel was successfully driven with the first Canadian rock tunnel-boring machine (RTBM or TBM), designed and built by Lovat Tunnel Equipment, Inc. The initial mine development consists of the drivage of two tunnels to the first major coal seam. Future plans are proposed for the development of a 4 million tonne-per-year mine (Marsh et al., 1983, Gillman, 1982), which will require the drivage of a further two tunnels and could access up to four coal seams. The tunnel cross-sectional areas were designed to provide sufficient ventilation area and access for a production of 4 million tonnes per year."

Jan 1, 1986

"With the plethora of cable bolts on the market, geotechnical engineers can be baffled by the differences in performance claims from the manufacturers but perhaps more importantly they are sometimes at a loss in making an optimal selection matching behaviour with a particular site condition. To this end a new testing methodology has been developed that can cater for the varying types of cable bolt behaviours. The methodology is based on the laboratory short encapsulation pull test (LSEPT) as recommended in the British Standard and overcomes several deficiencies such as cable rotation. Of most significance however, is its inability to measure the post-peak residual performance of high load transfer capacity cables and consequently, there is an inference that these cables may be susceptible to sudden anchorage failure with relatively little yield. This paper details the results of anchorage performance tests of a range of cable bolts and the differences in performance with rock strength and drill hole diameter.INTRODUCTIONA research project was undertaken to develop a new laboratory-scale test apparatus to study the axial performance of fully grouted cable bolts that are used in the Australian underground coal mining industry. Work by Thomas (2012) and others in recent years found there were a number of deficiencies in the testing methodologies making it difficult to determine and compare the performance of the dozen or more different types of cable bolts on the market. This has meant that geotechnical practioners have been hamstrung in optimizing the design of ground support systems in underground environments that are increasingly more arduous.A cable bolt is a flexible tendon consisting of a quantity of wound wires that are grouted in boreholes at defined distances between holes in order to provide ground reinforcement of excavations (Hutchinson & Diederichs, 1996). They were initially introduced into the underground hard rock mining industry in the 1960s (Thorne & Muller, 1964) and since the early 1970s have been brought to coal mining operations."

Jan 1, 2015

By A. A. McCloskey

APPROXIMA TEL Y 95 percent of Waite-Amulet's Lower A orebody will be mined by diamond-drill stoping. This method of stoping was developed, and has been successfully applied, at the Noranda mine in recent years(1) and is now used in several base-metal and gold mines in north-western Quebec and in other parts of Canada, South Africa, and Australia. The purpose of this paper is to deal with the features of the Lower A ore-body which led' to the adoption of this method of stoping, and in addition to give a general description of stope layout, stope development, main haulage development, chutes and grizzlies, diamond drilling for stope blasting, diamond drilling and equipment, primary blasting, secondary blasting, haulage and loading, ore pockets, pumping and drainage,. and shafts at Waite Amulet. Figure 1 is an isometric projection of the orebody, illustrating the mining system. The factors that led to the adoption of diamond-drill stoping of Lower A orebody are as follows: (1) Safety.0 (2) Size and shape of the orebody, and depth of the orebody below surface. (3) Strength of the hanging-wall, footwall, and sulphide ore. (4) Continuous ring-drilling from sub-level drifts, with no delay for blasting. (5) Large-tonnage blasts at the end of Saturday afternoon shift, after ali men are out of the mine. (6) Sub-levels may be retreated from top to bottom simultaneously, or lower sub-levels may be retreated first without any change in the ring-drilling la yout. (7) Large stopes up to 100 feet wide can be mined, leaving substantial pillars up to 60 feet in width, which may be partially recovered by âiamond~drill stoping or by other stoping methods. (8) A large tonnage may be drilled-off in advance of blasting, but only a supply of unoxidized ore for flotation treatment is blasted. (9) Better ventilation during working shifts. (10) Gravity flow of all broken ore to grizzlies located in the footwall of the orebody. (11) Electric blasting by a crew of two men.

Jan 1, 1941

By Nigel Saunders, Zhanli Guo

"Quench sensitivity of heat-treatable aluminium alloys is closely related to the precipitation process taking place during quenching. Faster cooling results in less precipitation of coarse phases during cooling, leaving more solutes in the solution before ageing. An alloy in such state would be of greater hardening potential as larger amounts of hardening phases may precipitate out during ageing. Hence, to understand the quench sensitivity of an alloy, it is essential to understand its precipitation process. Precipitation is a diffusion-controlled process and the diffusion is made complicated by the so-called quenched-in vacancies. These vacancies form during solution treatment, become “excess” when temperature goes down, and annihilate during the following cooling and ageing treatments, making diffusion now a function of both temperature and time. This paper first investigates the formation and annihilation of quenched-in vacancies and their effect on diffusion. The diffusion affected by quenched-in vacancies is considered in the kinetic models to realise the calculation of TTT/CCT diagrams for aluminium alloys. The calculated CCT diagrams have been used to explain the observed quench sensitivity and age hardening behaviour of various commercial alloys. The transformation from GP zones to other hardening phases during ageing is also discussed.INTRODUCTION The heat treatment of aluminium alloys mainly consists of three stages: a solution treatment at an elevated temperature, quenching from this solution treatment temperature to room temperature, followed by an ageing treatment to allow the precipitation of strengthening phases(Davis, 1993).The following statements generally describes how quench sensitivity is observed in heat-treatable Al-alloys: faster cooling results in,(i) less precipitation of coarse phases formed at high temperature during cooling, (ii) more solutes kept in solution before ageing, and (iii) larger amounts of hardening phases being formed, i.e. a greater hardening potential. Thus, the quench sensitivity of an alloy is closely related to its precipitation kinetics."

Jan 1, 2018

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By P. Reyes

The Codelco Chile El Teniente Division Caletones Smelter has an objective to smelt 1,250,000 tonnes per year of copper concentrate. This is a great challenge for the smelter facilities and particularly for the acid plants. The analysis ensuring that there are no obstacles to achieve the production capacity was of great importance. Therefore a series of activities were undertaken as well as studies dedicated to reach the target. This paper presents work focused on a fluid dynamic study, translated in an operation methodology of integrated handling of the smelting and converting gases with the objective to optimize the gas flow and S02 concentration. The optimization should be done employing the current installations, equipment and instrumentation and/or minor modifications. In the first part of the work the condition of the instrumentation involved in the gas handling was checked, improvements determined and the corresponding corrective actions were carried out. The proposed operation method consists of operation of the Cleaning Gas Plant 2 (TC' s gases) and operation of Gas Cleaning Plant 1 (the remaining gas plus the gases from CPS). The implementation of the operation method involves the modification of the valve of the gas into the duct to plant 1 from On to Off to modulate flow. After modification a three days test was carried out. To evaluate the tests, a "Sulphur Capture" indicator was used. During the test the behaviour of the effluent treatment plants was closely examined. No problems or unusual operating conditions were observed. The reduced flow of gas to Gas Cleaning Plant No. 1 permitted the start up of the 2nd test day treating most of the gas received by Gas Cleaning Plant No. 2. The operation was carried out with the limitation not to increase the effluent pond level, which was maintained constant.

Jan 1, 2007

By Blair Hrabi

Introduction; ?Risks Associated with the Resource Estimation Process; ?Limitations of Available Data; ?Geological and Structural Control of Mineralization Trends; ?Recognizing Multiple Mineralization Controls and Complex Trends; ?Accurate Geodomaining; ?Conclusions.

May 1, 2013

By R. Pressacco

"IntroductionAgrium’s history in fertilizer production and marketing goes back to 1931. Today, Agrium Inc. is a world leader in the production, distribution, and marketing of fertilizers and related products to the agricultural industry. Agrium is the largest North American producer of nitrogen fertilizers, a major producer of phosphate and potash fertilizers, and a world leader in fertilizer wholesale distribution and retail marketing. The mine at Kapuskasing is located some 40 km southwest of Kapuskasing, Ontario (Fig. 1). It has been developed to supply high-quality, low-cost phosphate rock to the company’s Redwater, Alberta facility, where it is an ingredient in ammonium phosphate fertilizer production. The Kapuskasing mine is the only phosphate mine in Canada and will rank as one of the highest-grade phosphate mines in the world (Clark and Duncan, 1999). Apatite is the principal ore mineral mined at the Kapuskasing Phosphate Operations.GeologyThe first record of exploration in the area was from a program executed by Continental Copper Mines in 1955 which evaluated the magnetic anomaly located in the Cargill and Cumming townships for its base metal potential. Intermittent exploration of the base metal potential of this magnetic anomaly continued in the following years, until the phosphate potential of the area was first examined in 1974 by International Minerals Corporation which recognized the presence of a layer of apatite sands overlying the carbonatite host rocks.The local geology consists of a core complex of multi-phased carbonatite rocks which are surrounded by a ring of pyroxenite, and have provided a U-Pb age date of 1907 Ma ± 4 (Sage, 1988). These two rock types are in turn situated within quartz diorite gneisses that form a large portion of the Kapuskasing Structural Zone (Fig. 2). The carbonatite host rock is sub-divided into two sub-types: sovite and rauhaugite. The sovite is a medium- to coarse-grained, white, banded rock in which calcite is the dominant carbonate species and it includes accessory minerals such as phlogopite, magnetite, clinohumite, apatite, olivine, pyrrhotite, and amphibole. Apatite can reach 15% abundance in this rock type (Sage, 1988). In sharp contrast to the sovite, the rauhaugite appears as a massive, fine-grained, dense, beige to tan-coloured rock in which dolomite is the dominant carbonate species. Phosphate values can range to 14% P2O5 in the rauhaugite."

Jan 1, 2001