Search Documents

By A. Giacomini, M. Nazem, E. Fathi Salmi

"Numerical simulation of collapse of tunnels in weak rocks is one of the challenging problems in rock mechanics. Collapse can impose technical and financial difficulties during the construction of underground excavations. This phenomenon, particularly in shallow excavations, may lead to propagation of a caved zone toward the surface and formation of chimney subsidence. Chimney subsidence has numerous catastrophic consequences such as the adverse environmental impacts and damage to surface structures in vicinity of excavations. Due to the importance of subsidence in civil engineering, the main goal of this study is to propose an appropriate method for preventing the formation of subsidence in shallow tunnels in weak rocks. The Dolaei road tunnel is investigated as a case study, where a large chimney subsidence has occurred. The geology of the area and the geostructural characteristics of the rock mass surrounding the tunnel are briefly reviewed in this paper. Two-dimensional as well as threedimensional numerical simulations are conducted to study the tunnel stability. Moreover, the effects of staged excavation and pre-supporting method on controlling the ground movements are studied. Outcomes of this study indicate that employing forepoling and staged excavation can be a practical remedy to control the ground movements and prevent the formation of chimney subsidence.INTRODUCTIONPredicting the formation of subsidence, mainly sinkhole subsidence over civil or mining excavations, is a very challenging task. An accurate prediction of subsidence is required for selecting an appropriate control and mitigation system to reduce the level of ground movements and its impact on the surface life (Bétournay et al. 1994; Leca and New 2007). Excavations, particularly in weak grounds, could result in surface subsidence; they modify the in-situ stress conditions as well as the hydrogeology of the area. Construction of unsupported excavations in soft soils and relatively weak rocks usually leads to the formation of a failure zone behind the face. In a very soft ground, the failure zone can extend towards the ground ahead of the tunnel face. Propagation of this zone toward the ground surface results in generation of sinkholes."

Jan 1, 2015

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

By L. Long

Stirred milling of nickel laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on siliceous goethitic (SG), goethitic (G), and saprolitic (SAP) nickel laterite samples (- 2000 ?m particle size) to evaluate the effect of stirrer speed, solid content, water salinity and grinding time. A fine mineral product (-38 µm) was used to evaluate the effect of selective grinding and Ni upgrade. The optimum grinding time for the highest Ni upgrade was 0.25 min, 0.1 min and 0.1 min for the SG, G, and SAP nickel laterite, respectively. A new feed (38-2000 µm) for each nickel laterite sample was prepared for batch grinding tests under the optimum grinding conditions. Upon grinding the 38-2000 µm feed, the - 38 µm product confirmed the effect of selective grinding and nickel upgrade. Size classification followed by stirred milling is a suggested process for Ni upgrade. The best Ni upgrade result was achieved on the SG nickel laterite among the three samples. The Ni grade increased from 0.85% to 1.37%, with 27.8% Ni recovery. Bottle roll leach tests showed that for SG and SAP samples selective grinding had no dramatic effect on Ni extraction due to the slow leach rate of hard mineral particles. Stirred milling of G sample increased the surface area of goethite, resulting in higher Ni extraction. Gravity concentration through a Knelson Concentrator was not effective in the further treatment of the stirred milling products either due to the poor operating conditions or due to the mineralogy characteristics of the feed samples. The energy requirement in the stirred milling was investigated. The first pass of the signature plots study is critical for the purpose of selective grinding, because the best result on selective grinding is achieved in the early stage of the grinding process.

Aug 1, 2013

By Robert W. Baker

"Brunswick Mining and Smelting commenced production at the No. 12orebody, a lead/zinc/copper/silver deposit, situated some seventeen miles southwest of Bathurst, New Brunswick, in 1964 at 4100 tonnes per day. Today it operates at 10500 tonnes per day.Brunswick has utilized underground incentives since commencement of operations. Early incentive systems were “off the wall"" based on those in effect at other properties then manipulated to fit, often hack calculated from actual performances to tm1ve at the desired result. If subsequent payouts were considered too high the rates were simply reduced, often retroactively. A large amount of this was' subjective and depended to a large extent on whoever was handling the bonus, in conjunction with senior mine department staff.In 1971, it was' decided that a more scientific approach was needed, particularly with the introduction of the new cut-and-fill mining. After some research, a system based on Work Study was selected. Another major mining company employing such a system loaned one of their experienced employees to train some Brunswick personnel in the art of Work Study and conversion of data to incentive rates, and in 1972, the first such developed incentive rate was-introduced.Along the way, borrowing from others where necessary, a set of Brunswick principles and parameters were developed. While refined to some extent, these remain basically the same today.Improvements in methods and equipment have resulted in improved performance and reduced costs. The use of underground incentives has played an important role in this. A/though individual bonus earnings have steadily increased, bonus cost per tonne has remained nearly constant - in real dollars, it has regularly decreased. These are two of the main parameters of a successful system."

Jan 1, 1995

By J. Robitaille, P. Cousin

"Agnico-Eagle Mines Ltd, Laronde Division, is a gold operation processing ore containing copper and zinc. Copper is recovered as a concentrate prior to gold cyanidation.Copper concentrate grade was improved with the implementation of an on-stream analyzer. Further improvements to the copper concentrate grade could be achieved throughefficient zinc depression.High cyanide cost linked to the copper content in the flotation circuit tails, prompted some modifications to the flotation circuit. Economics and environmental issues were considered. A Maxwell cell was retrofitted with an Outokumpu HG cell mechanism stabilizing it's operation. Secondly a flotation column was added to increase circuit capacity.This paper will address flotation circuit operation difficulties, successes and results achieved before and after modifications.RESUMELes Mines Agnico-Eagle division Laronde sont considéré comme étant un producteur d'or. Le minerai révèle toutefois des teneurs appréciables en cuivre et zinc. Un circuit de traitement combinant des étapes de flottation du cuivre et de cyanuration de l'or a été adopte. Le rejet de la flottation est lixivie pour son contenu en or.La teneur moyenne en cuivre du concentre final fut augmentée suite a l'implantation d'un système d'analyse en continu. Une séparation plus efficace de la sphalérite se devra d'être obtenue afin d'améliorer davantage la qualité du concentre produit.Le contenu en cuivre au rejet du circuit de flottation influence directement la consommation en cyanure. Pour cette raison, certaines modifications à la flottation sont devenues nécessaires. Des facteurs d'ordre économique et environnemental ont été considérées. Une cellule existante fut transformée en cellule HG d'Outokumpu, stabilisant son opération, et une colonne de flottation fut ajoutée au circuit afin d'accroitre sa capacité.Le présent document se veut une rétrospective des problèmes d'opération vécus, des solutions apportées ainsi que des résultats obtenus et de leurs implications suite aux améliorationseffectuees."

Jan 1, 1995

By J. S. Stewart

THE Mackenzie River Valley proper extends from Great Slave lake to the Arctic ocean (see map, Figure 1). From Fort Providence, near Great Slave lake, to Aklavik, near the Arctic coast, the distance by river is 1,000 miles. This will give some idea of the extent of the region. Throughout the length of the river valley, the Precambrian complex rocks are overlain by unaltered sedimentary rocks several thousand feet in thickness. These sediments are dominantly marine and Palaeozoic in age. In places, the Palaeozoic strata are overlain unconformable by Cretaceous an Tertiary sediments. The strata have been folded and, in general, the inclination of the beds to the horizontal is comparatively gentle. Here, then, we have the essentials for potential oil fields covering an area over 1,000 miles in length. This is probably the largest comparatively unexplored potential petroleum region in North America, and surface evidences of oil in the form of seepages occur in several places. Many of these seeps were known to the early explorers, and the first Geological Survey report on the Mackenzie River region, containing the results of field work carried out by R. G. McConnell in 1887-88, noted the petroliferous character of the Devonian strata and the indications of petroleum(l). This region is, however, handicapped by distance from markets and sources of supply of materials; by lack of modern transport facilities; by short season for river transport, and mountainous country separating the valley from the Pacific seaboard; and by the long winter season with weather that makes outdoor work difficult. These factors have tended to discourage the enthusiasm of would-be promoters, and so development in this region has been slow In 1920, a test well drilled about fifty miles northwest of Fort Norman discovered oil in commercial quantity, and three additional wells proved a small area to be productive.

Jan 1, 1944

By N. K. Jaber

The "Pidgeon Process" for the extraction of magnesium from dolomite ore utilizing ferrosilicon as the reducing agent has been studied extensively by active metallurgists such Mr L,M, Pidgeon the father of this process, Most of the work sited so far has focused on heating the (FeSi/MgO,CaO) briquette mix under vacuum in stainless steel retorts by external fuel hydrocarbon heating, In this work Electrical Induction Heating was employed as the heating method whereby the briquette mix was placed in a steel crucible around which an Induction Heating copper coil was wound and placed inside in a stainless steel vacuum tank, It was observed that by virtue of the fast Induction Heating method utilized in the silicothermic extraction process higher reduction temperatures were reached in shorter periods of time due to fast heat transport into the ore charge mix, This facilitated shorter metal reduction times as compared to the conventional fuel heating methods.

Jan 1, 2006

By Tim Grain Joseph

This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sand material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 square yards. Consequences are manifest in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability. The objective of these considerations, as part of the Oil sands Equipment Interaction Program (OsEIP); currently a joint venture between Syncrude Canada Ltd., JPi Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta; is to identify and provide feedback to the manufacturer and end user adverse shovel - ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance.

May 1, 2002

By J. G. Peacey

"Canada has a special place in non-ferrous pyrometallurgy because it is the only country in the western world that is a significant producer of all the major non-ferrous metals; aluminum, copper, lead, magnesium, nickel and zinc. This large non-ferrous pyrometallurgy industry has developed because of Canada's abundant mineral wealth and energy resources. Table I summarizes the number of primary non-ferrous production facilities in Canada and their share of western world production.Production of non-ferrous metals is a mature, capital intensive business and its basic processes have been in use for many years. Nevertheless, these processes have continued to evolve in response to changing needs and external pressures; such as the energy crisis of the early seventies; historically low metal prices in the early eighties and the continuing pressure to reduce plant emissions and improve in-plant working conditions. Canada's major metallurgical companies: Alcan, Cominco, Falconbridge, Inco and Noranda have played a leading role in pioneering new process technology and continue to meet the difficult challenge of keeping their operations competitive in the global metals market. This paper will try to give an overview of the major developments in non-ferrous pyrometallurgy, largely from the Noranda and Canadian perspectives, highlighting the current status of process technology and possible future directions.AluminumCanada has the world's second largest aluminum smelting industry and its capacity has expanded rapidly in recent years with the completion of several large projects in Quebec. The location and capacity of the Canadian aluminum smelters are given in Table 2. All these plants use the Hall-Heroult process, that was invented over a century ago but over the last twenty years considerable improvements have been made to increase productivity, reduce power requirements and emissions.The developments in aluminum cell technology can be illustrated by the experience at Noranda Aluminum. In 1971, Noranda Aluminum started its first pot line using Kaiser's P69 prebake cell, which was considered, at that time, the best available technology. The P69 cell was designed primarily for high productivity, operating at 150 000 amps and high current density to produce just over tonne Al per cell-day. The P69 cell is a simple design, typically operating at about 88070 current efficiency and 15 800 kWh/tonne Al. When Noranda Aluminum decided to expand in 1980, the Alcoa 697 cell was selected as it then represented the most proven, stateof- the-art technology. This cell is similar to that installed at Alcan's new Grande Baie and Laterriere smelters and is designed to operate at 180000 amps and 93070 current efficiency, producing about 25070 more aluminum per pot-day than the P69 cell using about 15070 less power. The 697 cell has a much more sophisticated cell design, with very good balancing of the magnetic field giving a flat metal pad and allowing efficient operation at the higher amperage. Alumina is fed via point feeders that provide an almost continuous feed allowing close control of the alumina level in the bath and the use of low-ratio bath composition, giving much higher current efficiencies."

Jan 1, 1991

By C. Gerow

THIS paper is entitled "Some" problems, rather than "The" problems, met in selling coal, since the problems to be met in selling any commodity have to deal with an infinite number of circumstances and conditions. These are believed to be more varied in the case of coal than probably any other commodity. This is due, perhaps, to the fact that coal has been one of the basic materials in the guiding of industrial and national achievement for the past two hundred years. During this time its use has developed from a most haphazard one to uses involving all modern scientific methods, which, rather than simplifying matters as regards the marketing of coal, have added many fresh problems, and these vary according to the particular market served. Since the concern of this paper is primarily the selling of Nova Scotia coal, it is proposed to deal chiefly with some of the specific conditions met in the markets presently served by this coal. For the purpose of discussion, these markets may be considered as divided into three main groups, namely, the Maritime market, the Quebec market, and the Ontario market. THE MARITIME MARKET First of all, let us consider the Maritime market. This is a market which has been regularly served by Nova Scotia coal since coal mining became the first industry in Cape Breton, slightly over one hundred years ago. Conditions as applying to the use of coal have naturally tended to adjust themselves to the characteristics of the coal most readily available, and, therefore, marketing problems are fewer in the Maritimes than in districts where many coals of varied characteristics are offered. Up to recent years, the problems involved were chiefly those of providing satisfactory service insofar as de-liveries were concerned. However, with the speeding-up of manufacturing processes and the necessity of reducing costs to a minimum, users of coal have become interested in obtaining coal that will give the most economical service. It is, therefore, now of importance that the salesman should have full knowledge of the particular conditions applicable to each customer's use in order to deal to the best advantage.

Jan 1, 1936

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2004

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

By Manqiu Xu, Joe Holmes, Peter Wells, Peter Langlois, Germain Labonté, Jim Barrett

"The flowsheet for the Voisey’s Bay mill had to meet the challenge of processing an ore containing high pentlandite and chalcopyrite values in a largely pyrrhotite/troilite matrix. In the 1994-97 period, circuit development focused on making a high-grade copper concentrate and a relatively low-grade nickel concentrate. However, in 1998 a circuit with copper concentrate, high-grade nickel concentrate and a Ni/Cu middlings concentrate was specified. Following a three year project delay, work resumed on the flowsheet in 2001, and the target for the overall grade of the nickel concentrate was raised from 14% to 20% nickel. To achieve this target triethylamine tetramine (TETA) and sulfite pyrrhotite depressants were used in an all lime circuit. It later became evident that, with appropriate selection of collector and adjustment of the circuit by the addition of a scavenger on the scavenger cleaner, it would be possible to approach the grade of concentrate required without the use of pyrrhotite depressants. The recycle of water and the contained thiosalts was also proven to be instrumental in raising the grade.Construction and commissioning of the mill were fast-tracked with start-up of the mill in September 2005 some six months ahead of the original schedule. Ramp-up of both throughput and metallurgy was faster than any other recent nickel installations with tonnage being limited mainly by concentrate dewatering due to the higher than initially planned ore grades.INTRODUCTIONNickel was discovered in the vicinity of Voisey’s Bay by Chislett and Verbiski working for Diamond Field Resources in 1993 and the Ovoid deposit was delineated in the winter of 1994/95. By the end of 1995 the Ovoid had been well explored and at that time was thought to have a reserve of at least 30 million tonnes with an average grade of 2.83% Ni and 2.0% Cu. Drilling to the east of the Ovoid had indicated the presence of significant mineralization. In June of 1995, Inco Limited bought a 25% share in the Voisey’s Bay Nickel Company (VBNC) which was a subsidiary holding company set up by Diamond Fields. Inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBNC for twenty years as part of this agreement. In April 1996, Inco bought the 75% of VBNC shares that it did not own."

Jan 1, 2007

By K. J. R. Ford, Botz. M. M.

Porphyry copper ores are frequently a source of low-grade gold ore, but gold in these ores is often associated with significant levels of cyanide-soluble copper. Cyanide leaching of such ores increases flowsheet complexity and operating costs, and requires thorough planning to satisfy environmental requirements for tailings disposal and mine closure. This paper presents a review of the chemistry of cyanide leaching of gold-copper porphyry ores, carbon adsorption phenomena and means of removing base metals from leach solution. The primary economic drivers behind the processing of such complex ores are also analyzed.

Jan 1, 2011

By Ning Yu

There are about 1.341 trillion tons (t) of proven coal reserves in China, of which 279.58 billion t are available for mine well construction basis. Thick coal seams are 44% of the reserves. The production of thick coal seams exploitation is over 45% of the total coal production. Full-seam mining and fully-mechanized mining for large mining height is the technology development direction of thick and extra thick seam mining. It is also the important way to achieve efficient and intensive mining with the characteristics of high production, high mechanization, high efficiency and low energy consumption, etc. Complete set of technology and equipment of fully-mechanized top caving for large mining height of full-seam (7m) mining and extra thick seam ( 14-20m) has been gradually mature and for demonstration application by the joint research of government, enterprises, universities, scientific research organizations and users. It has solved some technical problems of coal face for large mining height (over 7m) such as the coal wall spalling control, stability of support, wall rock coupling, cooperation work of mining and caving, full roadway support for super large section, end support, equipment matching of coal shearers, hydraulic support and scraper conveyor. It has developed key equipments including powerful hydraulic support of fully-mechanized mining and fully-mechanized top caving for large mining height, electrically-driven coal shearer with high speed and reliability, scraper and belt conveyer with big capacity, soft-start and high reliability, automatic control system of coal face with the core of electric-hydraulic control, bolting drill boom large section coal roadway shearer, heavy auxiliary transport equipment. The operation rates of fully-mechanized top caving equipment for full-seam and large mining height are 94% and 92.1%, and recovery ratios are 93.6% and 88.9% respectively. The annual raw coal production of single work face is over 10 Mt. The automation and intelligentization level have been clearly improved. The exploitation of thick and extra thick coal seam that is safe and efficient has been achieved in China.

Aug 1, 2013

By James McManus

The original analogue instrumentation at Lornex Mining Corporation to optimize the throughput by controlling the power drawn by the semi-autogenous mills was found to be inadequate because of the frequent changes in ore type. Although the trunnion bearing pressure of the mill was a crucial control criterion, it was not utilized in the original control scheme. After several plant tests of different types of analogue controllers were unsuccessful in finding any control equipment suitable for this application, it was concluded that a digital process control computer was required. Computer control strategy to optimize the grinding rate by controlling the power and the bearing pressure of the semi-autogenous mill was developed and a Fox 2 /30 computer made by Foxboro was selected. After six months of experimentation, it was found that the throughput was increased substantially by computer control.

Jan 1, 1978

By Mark Ferra

Flotation is used in mining to produce concentrates of copper, gold and several other valuable ores. In 2017, a copper mine near Globe, Arizona improved their rougher cells productivity using technically advanced electro-hydraulic actuators in the flotation process by enabling excellent tank pulp level process stability. The new actuators controlled the dart valve position to allow pulp to leave the cell. Tank cell pulp level can change due to feed and discharge fluctuations from neighboring tanks. When traditional pneumatic actuators are used, they have sluggish response times and overshoot due to the inherent physical property of air being compressible. Electro-hydraulic actuators have the benefit of hydraulic stiffness to deliver accurate and repeatable (0.1%) dart valve positioning. The froth layer has more opportunity time to maximize mass transfer into the launderer. The results are an increase in copper recovery by 2-4%. INTRODUCTION In 2013 there was an international flotation technical conference well attended by respected flotation specialists for both mining companies and academia. During the technical session a leading metallurgist was discussing pulp level measurement and said that when he was on the cell deck he stated, pneumatic actuators air cylinders stroking up and down. The presenter then claimed with confidence that "I listened to actuator move so the pulp level in the tank was being controlled!" No one questioned his assumption and I can assert that the audience was quite technical and not shy in their critiques of speakers. The flotation community simply believed that the existing pneumatic technology was enough with no alternative. Having a stable flotation cell pulp level is critical to effective copper recovery. Controlling pulp levels in flotation cells is a complex task that includes modulating dart valves in each cell. The use of REXA Electraulic actuators will decrease the process dead time and maintain froth height in a controlled manner, especially from pulp slurry volume fluctuations from neighboring cells. By reducing flotation cell pulp level tank height variation, a copper mine in Arizona has realized a 2-4% recovery improvement by increasing the froth transfer to the launderers in the rougher cell circuits compared to pneumatic actuators. This paper examines the benefits of using an electro-hydraulic actuator to ensure proper pulp level control and reduce the process operational cost. It will focus on actuator positioning the dart valves to maintain pulp level setpoint at a copper mine in Arizona.

Jan 1, 2019

By G. R. Guillet

"Bricks made from local Paleozoic shales, and floor and wall tiles made from imported clays, both established record production volumes in 1985 and are the strongest segments of Ontario 's clay products industries. However, renewed interest in traditional materials also supports a good market for clay flower pots and flu e liners, and innovative processing studies are showing promise for possible new production of clay roofing tiles. This paper reviews the highlights of a comprehensive study of Ontario's clay products industries, completed in 1986. IntroductionFor some years now, Ontario' s clay products industries have been unspectacular in their attempt to cope with the recent recession and the impact of alternative materials. But a strong demand for bricks in recent years has done much to dispel the gloom.Bricks, drainage tiles, sewer pipes, flue liners, structural and partition tiles, and flower pots have been commonly referred to as ""heavy"" clay products, and they have been based largely on local clays and shales. To this list might be added expanded aggregate and mineral wool. Clay refractories, sanitary ware, electrical porcelain , art pottery, and floor and wall tiles are not considered heavy clay products, and are commonly made from a variety of ceramic materials, many of which are imported.Production facilities for heavy clay products often began in Ontario as small family enterprises, using whatever clay was available locally to supply the local market with building bricks and other clay products needed for construction. Improved road systems increased the market range for these plant s, and new technology and industry standards resulted in gradual"

Jan 1, 1988

By A. Ghasemi

An alumina-silica coating was deposited on a nickel substrate by sol-gel process, and the structures and composition were evaluated, The sols were made from aluminium and silicon alkoxide, and an acid catalyst including HCl, To produce adherent silica coatings on nickel, various additives such as surfactant, viscose additive and drying control chemical additives were introduced to the system, and appropriate drying and firing cycles were applied after dipping in solution. The hot corrosion and oxidation resistance of the coating at different temperatures were investigated, The structure and uniformity of the coatings were examined by scanning electron microscopy (SEM), The results indicate that a uniform coating of alumina silica can be produced on a nickel substrate by optimizing the composition and process variables of the sol. Coatings can protect substrates from oxidation and hot corrosion at different temperature up to 1000°C, but is not very effective for hot-corrosion resistance at 1000°C.

Jan 1, 2005

By Denis Yaychuk, Gary Billingsley

The economic eva luation of a mineral property or mining venture should include the quantification of ri k as part of the analy is. The re ults of such an analysis provide the decision-makers not only with the most likely financial outcome and the probability of achieving that or any other outcome. but al o with a ranki ng of the relative impact of all the ri sk factors. These type of resu lts offer more complete information for investment and technical deci ions than the traditional cash flow/ ensitivity analysis. In addi tion. by attempting to quantify ri sk. the personnel providing the va ri able input are forced to take a much clo e r look at the data involved, and are fo rced to work together. the reby increa ing substantially the awa reness of the impact their work and others· work has on th e outcome of the analysis.

Jan 1, 1986