Search Documents

By N. Kolev, M. Poibrenski, I. Nishkov

"The following paper examines the flotation of copper porphyry ores in Assarel concentrator with focus on the reasons for low molybdenum recovery in the final copper concentrate. The copper-porphyry ore of the Assarel deposit is characterized by its variable mineral composition and high clay content, which influence the process efficiency of their concentration. Particle size distribution, chemical and mineralogical analyses have been made on various flotation products showing the distribution of the main elements of interest - copper and molybdenum. It was found that molybdenum is not concentrated into the final copper concentrate as usual in the flotation of copper-molybdenum ores but into the tailings of the copper selective flotation (cleaner tailings). An attempt to explain these results has been made with proposals to improve molybdenum flotation. Low floatability of molybdenite is caused by the ultrafine clay minerals content in both the run-of-mine ore and copper flotation streams. In order to achieve selectivity of copper minerals against pyrite a significant amount of lime is used in the plant leading to higher pH conditions, which could be another possible explanation for the molybdenite depression. The results obtained after the laboratory experiments, showed that it is possible to restore molybdenite floatability using traditional reagents such as diesel, kerosene, etc., and introducing a new polymeric reagent as froth modifier.INTRODUCTIONOne of the main technical difficulties in the area of copper-molybdenum flotation is the selective recovery of both metals, especially the fine (<40 micron) mineral particles. The problem is even more serious when Cu-Mo ore treated contains a lot of natural fine particles, predominantly clays, micas and other gangue minerals. Peng and Zhao (2011) conclude that the mineral processing industry is well aware of the difficulty in treating ores in the presence of clay minerals. Tremolada et al (2010) found that clay minerals have been named as the main problem in ore beneficiation processes due to their small size, which cause a higher viscosity in grinding. In flotation, these clay minerals have natural hydrophobicity or float by entrainment.The impact of clay mineralogy on flotation performance has been reviewed in the literature and the various deleterious roles of clay minerals have been investigated (Bulatovic, Wyslouzil & Kant 1999; Jorjani et al, 2011; Farrokhpay, Bradshaw & Dunn, 2013). It is widely accepted that the actual flotation recovery problem appears to be caused by the properties of these fine particles: small mass (and/or momentum) – high interfacial free energy (Rubio et al., 2007; Farrokhpay, 2011). In most cases, the loss in recovery is found to be insignificant, but the detrimental effect on the concentrate grade is found to be more prominent. The main reasons for the flotation inefficiency are the low probability of bubble-particle collision and adhesion, formation of dense froths and as a result - low process kinetics. A great deal of fine valuable minerals is discarded as slime in flotation due to lack of effective recovery methods."

Jan 1, 2016

By Xiaozhu Chen, Qi Ping, Pu Yuan, Qinyong Ma

"In order to investigate the fractal feature of coalmine deep rock fragments under impact loads, variable cross-section split Hopkinson pressure bar apparatus, 50 mm in diameter, was adopted to conduct impact compressive test for rock specimens from -962m deep coalmine. Various impact pressures, such as 0.3, 0.6, 0.9 and 1.2MPa, were selected to implement different loading rates. Sieving statistical analyses were conducted for rock fragments after being impacted, and the particle size distribution of broken rock in various loading rates were calculated with the fractal method and then the corresponding fractal dimension was obtained. Test results shows that there is a good self-similarity and fractal feature in fragments distribution of deep coalmine sandstone under impact loads. The fractal dimension of fragments is between 1.9 and 2.7. The research also indicates that there is an approximate power relationship between dynamic compressive strength and fractal dimension, and a strength power relationship between fractal dimension and average strain rate. Moreover, there is a linear relationship between fractal dimension and specimen absorbed energy. The rock fractured process can be quantitatively described through fractal dimension, which can reflect the deep rock broken degree and is an ideal index to evaluate the distribution of rock fragments.INTRODUCTIONBroken rock is one of the most basic processes in mining operations, rock fragmentation has always been an important index to evaluate rock breaking effect (Xu & Yu, 1984). Macroscopic fragmentation of rock material is the final results of continuous development, expansion, gathering and cutthrough of internal micro-cracks. This process, developing from microscopic damage to macroscopic fragmentation, is an energy dissipation process and shows fractal characteristics (Xie, 1993). Turcotte (1986) has conducted statistical analyses of fragmentation for different kinds of geological materials under various broken conditions, and arrived at the conclusion that fragmentation distribution is a fractal."

Jan 1, 2015

By Michael L. Free, Zongliang Zhang, Joshua M. Werner

In the copper electrowinning process, short-circuiting between the anodes and the cathodes is a critical problem that changes the current allocation among local electrodes and reduces the current efficiency significantly. Possible reasons for the short-circuiting include the improper alignment of the electrode, bent electrode, and nodules on the cathode surface. In typical tankhouses, there is often a time between shorting and harvesting as well as between shorting and clearing. Therefore, it is inevitable to have short-circuiting affect the operation performance in practical electrowinning operations. However, one key piece of missing data is the actual measurements of the current efficiency as short-circuiting is approached and allowed to continue. Consequently, short-circuiting tests that allow tracking of electrowinning parameters before and after short-circuiting were performed in a laboratory scale Cu electrowinning cell. In the tests, the electrode spacing change, the mass of electrodeposited Cu, the deposition morphology, and the current allocation as well as the current efficiency before and after short-circuiting were studied. Results show that the short- circuiting affects the current allocation and the current efficiency significantly. Moreover, it changes the Cu deposition on the short-circuited cathode and therefore causes problems for Cu electrowinning. INTRODUCTION Electrowinning (EW) is commonly used for copper production around the world, with a rated production from 120,000 to 200,000 tons per year per operation (Wiechmann, Aqueveque, Henríquez, Muñoz, & Morales, 2014). In Cu electrowinning, Cu ions in the electrolyte are reduced on the cathode surface as metallic copper with a DC current, while on the anode, a counter anodic reaction occurs with oxygen gas generation (Werner, Zeng, Free, Zhang, & Cho, 2018; Zhang, Werner, & Free, 2018; Zhang, Werner, & Free, 2018). In copper electrowinning, an average current density of 200 to 400 A/m2 is applied to the electrowinning cell (Wiechmann et al., 2014). As the Cu deposits on the cathode, the distance between anode and cathode reduces and most of the time, short-circuiting forms between some anodes and cathodes in a large tankhouse containing thousands of electrodes, reducing the current efficiency and increasing the energy consumption significantly. The current efficiency in well-run copper EW operations is typically above 90 %. Most of the unused current is wasted through short circuits, stray currents, and by-byproduct formation (Davenport, King, Schlesinger, & Biswas, 2002; Wiechmann, Vidal, Pagliero, & Gonzalez, 2002; Wiechmann, Morales, & Aqueveque, 2010). Usually, in the tankhouse, the short-circuiting increases the current in the involved cathode by up to 1500 A (Wiechmann et al., 2010). Multiple reasons can cause the short-circuiting in the cell, and the most common reasons include the uneven current distribution among cathodes, tilted electrodes, bent electrodes, and nodules formed due to the large deposition roughness. Recognition of this challenge in the Cu electrowinning process has led researchers to perform many investigations on approaches to avoid and reduce the short-circuiting in the cell. A series of research investigations have been conducted to develop and improve a new type of intercell bar for Cu electrowinning (Wiechmann et al., 2002; Wiechmann, Morales, Aqueveque, & Burgos, 2007; Wiechmann, Morales, & Aqueveque, 2009; Wiechmann et al., 2010; Wiechmann et al., 2014). The associated test results show that this new design limits the occurrence and magnitude of short circuits and allows operation at higher current densities. Sandoval, Clayton, Dominguez, Unger, and Robinson (2010) stated several keys to control short circuits, such as maintaining the straightness of the cathode, removing “edge hair” from the cathode starter, and maintaining electrode alignment in the cell. Prengaman and Siegmund (1999) from RSR technologies developed a new Pb-Ca-Sn anode to prevent the anode deformation, thereby reducing the short-circuiting in the Cu electrowinning cell. Although the negative effects of short-circuiting on the Cu electrowinning have been recognized, and various investigations have been conducted to address this issue, the actual measurements of the electrowinning behavior and performance as short-circuiting is approached and allowed to continue are seldom reported. However, in typical tankhouses, there is a time between when shorting occurs and harvesting/clearing are performed. One key factor in determining the harvest time is the frequency of shorting. Consequently, we have performed short-circuiting tests that allow us to track electrowinning parameters before and after short-circuiting.

Jan 1, 2019

By Mary Kama, Kaul Gena

"Magnetic skarn ore (MSO) is one of the major copper bearing ore extracted by the Ok Tedi Copper Mine in Papua New Guinea. Copper minerals are recovered by flotation while the iron not associated with copper are discarded as tailings. The objective of this investigation was to determine the iron ore reduction kinetics for the Ok Tedi MSO and ascertain if it can be processed to produce sponge iron for a mini steel plant in Papua New Guinea.SEM-EDAX analyses of the Ok Tedi MSO indicated 10.1% C, 30% O, 0.6% Mg, 1.1% Si, 21.1% S, 0.8% Ca and 36.2% Fe. Most of the iron is in sulfide form. Both naturally occurring and roasted sinters of Ok Tedi MSO samples of different particle sizes were reduced by charcoal carbon at three different temperatures and seven different reduction times. Analyses of the reduced products indicated a metallic iron content of more than 65 wt.% on average.Results showed that there was no significant difference in reduction between fluxed and control materials. Only a slight increase in kinetics with reduced particle size, hence the reaction rate constant (K) did not vary much within the temperatures investigated. Reaction kinetics increases with increasing reduction time at 900°C. Therefore, more iron reduction is observed with particles of 106 µm size. In addition, the results also confirmed that the reduction energy used was higher at 800°C and lower at 1,000°C. In summary, iron reduction can be improved but close monitoring of temperature and reduction times are essential to determine the reaction kinetics of the Ok Tedi MSO. INTRODUCTIONMost mines in Papua New Guinea mine large quantities of iron in the form of sulfides, carbonates, oxides and sulfates that are eventually disposed off as tailings. The Ok Tedi magnetic skarn ore (MSO) contains a significant amount of hematite, magnetite, siderite, ilmenite and pyrite that can be a source of iron. The mineralogical compositions of Ok Tedi MSO reveals more iron minerals than copper, yet all iron containing minerals are collected in the tails from the main copper production stream. Therefore, this study is conducted to investigate the possibility of producing direct reduced iron (DRI), or sponge iron, from the MSO. Such sponge iron may serve as the feedstock for electric arc/induction furnace based mini steel plants in Papua New Guinea."

Jan 1, 2016

By Robert B. Parsons

"A study recently completed by the Prospectors and Developers Association, assisted by the author and computerized mine models he developed, presents a strong case that present tax rules severely handicap the junior exploration company relative to the established producer. This month, Tax Notes briefly summarizes the highlights of the study and some of the Association&apos;s ideas which came out of the study.IntroductionIn the case of any industry, a particular project or investment will generally generate a more attractive after-tax rate of return to a tax paying entity than to a non-tax paying entity: the ability to shelter current taxable income with tax deductions related to the project or investment can present a definite advantage as compared to shielding taxable income in the future with the same deductions. But, this advantage is probably seen nowhere more clearly than in the mining industry where the tax rules allow for substantial up-front write-off&apos;s. Studies show that the junior mining company which is earning no taxable income currently can be seriously disadvantaged, compared to the mining company which is currently generating taxable profit and paying taxes. This is particularly disturbing when one considers the importance of the junior segment of the mining industry. One might well ask where the equity is, in a tax system which causes the junior company to look at a deposit and see rock in the ground, when at the same time the deposit represents a viable mine to an operating company. This inequity and the importance of the junior mining company have been recognized to some extent in the income tax legislation. In recent years, the expansion of the rules for deducting certain earned depletion allowances against any source of income, and changes to improve the flow-through share rules, have gone part way in helping to put the junior on a more equal footing with the operating company. But it is questionable whether or not these helpful changes to the tax rules have done enough to alleviate the apparent inequities in the income tax legislation."

Jan 1, 1985

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By V. F. Kozyrev, L. B. Tsymbulov, L. Sh. Tsemekhman, A. N. Golov

Gipronickel Institute, JS has developed a new process and equipment for melting copper raw material in a two-zone Vaniukov furnace resulting in the production of white matte and low-grade slag in terms of copper content. Tests on processing copper nickelcontaining ore from Norilsk (Cu - 17 %), Ni - 3 %) were conducted in Vaniukov pilot furnace (total area 11.4m2) of Severonickel Combine. The amount of the processed material was about 11 thousand tons. Principal results of pilot testing are presented.

Jan 1, 2007

By Juergen Antrekowitsch, Stefan Steinlechner

"Within the last decades, mainly the base metals, like zinc, copper and lead were recycled from different industrial residues without taking into account that accompanied minor side-elements are often also present. A high supply risk for critical raw materials derives mainly due to the high share of the worldwide production in a limited number of countries. Examples include indium and germanium in China, PGM in South Africa and Russia or cobalt and tungsten in the Democratic Republic of Congo. By taking the market of critical metals into account, the recycling of potential residues does not only contribute to an economic treatment but also to the European strategy to decrease the supply risk of certain metals. Depending on the metal discussed, political unrest, decreasing primary resources leading to supply risks in different countries or also simply economic interests moved these mentioned side elements and with this the residues where they are present in, into the focus of the recycling industry.Because of this, the typical routes of lead, zinc and copper production are evaluated concerning generated residues and their typical contents of contained minor elements. Finally, the paper tries to answer the questions how a possible treatment of these wastes could contribute to the overall supply of for example silver but also other minor elements."

Jan 1, 2016

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009

By G. B. Hudson

Previous papers (1, 2) pertaining to the treatment of uranium-bearing ores were concerned with the flotation of the radioactive minerals. In this investigation, the application of flotation to the removal of acid-consuming minerals from uranium ores was considered. Two pitchblende-bearing ores, which, because of the presence if dolomite were abnormally high acid consumers, were studied. In both in-stances commercial reagents of widely varying fatty acid composition proved satisfactory as flotation col-lectors, particularly at a pH of 10.5, for the carbonate minerals. From an economic viewpoint, however, Neo-Fat 42-12 was favoured. A mixture of sodium tripolyphosphate and citric acid was an effective depressant for the pitchblende in the ores. The tailings remaining after the removal of the dolomite by flotation contained, in one case, 88.5 per cent of the uranium in the original sample, and, in the other, 93.8 per cent. Analyses conducted on these tailings and on the original ores showed that

Jan 1, 1963

By A. M. Simons

Cyanide destruction by Caro’s acid is one process commonly employed by gold operations to meet regulatory requirements and/or the International Cyanide Management Code compliance for weak acid dissociable (WAD) cyanide in cyanidation tails or waste water from such operations. Typically smallscale bench tests to evaluate and assess the suitability of the Caro’s acid destruction process are conducted. Additionally, the experimental procedure used during these preliminary investigations may also differ from that implemented at the full-scale. This paper presents the results from a fundamental investigation of the Caro’s acid process to establish a more detailed understanding of the impact that the experimental procedure has on the destruction of cyanide. In particular, it was found that the control of pH was important to avoid copper(I) cyanide precipitation at low pH and maximise WAD cyanide destruction. Residual peroxide in the preparation of Caro’s acid has the potential for subsequent cyanide destruction and could be exploited.

Jan 1, 2014

By Charles J. Zablocki, Robert J. Kamilli

"Abstract - Buried, possibly mineralized granite cupolas at the Silsilah tin deposit in Saudi Arabia (lat. 26°06&apos; N, long. 42°40&apos; E) have been successfully located using a closely spaced electric-field-ratio profiling technique. In this study, electrical fields at 27 and 270 Hz across grounded electrodes spaced 50 m apart were measured along six traverses. This method is interpretable by inspection, unlike the dipole-dipole technique, which requires mathematical modeling for interpretation.In the study area, the technique allowed the authors to identify and distinguish among unroofed granite cupolas, cupolas with their aplite-pegmatite apical contact zones intact, strong (quartz-rich) and weak (relatively quartz-poor) greisens, dikes, faults, and pervasively argillized rocks.This method should be useful in the valuation of other shallow mineral prospects in similar settings in other parts of the world, especially deposits for which the location of vertical contrasts is important, such as veins or mineralized zones associated with the apexes of small igneous cupolas."

Jan 1, 1993

By Zhibao Li, Lanmu Zeng

The behavior of dicalcium silicate in NaOH-NaAl(OH)4-Na2CO3 solution is of significance for controlling the silica level in the production of alumina via the sintering process. Dicalcium silicate samples were obtained through a twostep approach: coprecipitation of calcium and silicate from CaCl2-Na2SiO3-NaOH solutions; and calcination of the hydrated precursor at 1200°C for 4 hours. The optimization of the synthesis parameters including temperature, solution concentrations and aging time was also investigated. Xray diffraction (XRD) and chemical analysis show that the calcined solids include dicalcium silicate with trace amounts of wollastonite. The solubility of the synthesized dicalcium silicate in HCl, NaOH, mixed NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was determined. It was found that the solubility increases with increasing HCl and NaOH concentration. The effect of temperature on the solubility in HCl solutions is limited, but the solubility decreases with increasing temperature in NaOH solutions. The solubility of dicalcium silicate in NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was shown to increase with increased temperature, Al(OH)3 and Na2CO3 concentration. The BromleyZemaitis model for the aqueous electrolyte system was selected to predict the solubility of dicalcium silicate. The model’s predictions yielded certain success compared with experimental solubility data.

Jan 1, 2014

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth&apos;s crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature&apos;s materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man&apos;s use of horn, another substance with peculiar properties of roughness in all directions without the &apos;grain&apos; of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By P. Kawulka

An integrated pilot plant for the development of the S-C Copper Process was constructed at Fort Saskatchewan in 1975 and operated in 1976. The pilot plant was designed to treat 9 tonnes per day of a pyritic copper concentrate. A demonstration run conducted during the last quarter of 1976 averaged 90% on-stream time, and confirmed that the process is operable as a stable and integrated unit. The paper describes the parameters and equipment developed for thermal activation of chalcopyrite copper concentrates to make them amenable for the dissolution of iron and zinc, and their subsequent separation and recovery. The resulting high-grade copper sulphide was leached with return electrolyte and oxygen to extract 98.5% of the copper into solution. The copper was electrowon at 650 amps per square metre from purified solution, to produce cathodes analyzing 0.1 ppm Se, 0.1 ppm Bi, 4 ppm Pb and 10 ppm S. The electrical conductivity was >101% lACS and the spring elongation value [ ]350 mm. Elemental sulphur and gangue are removed from leach residues to make a concentrate containing over 95% of the silver and gold and most of the unleached copper. Conventional construction materials such as stainless steel, titanium, Hastelloy, acid brick, rubber and plastics performed well. The containment inherent in hydrometallurgy provided high standards of hygiene and safety.

Jan 1, 1978

By K. Baris

Methane (CH4) present in coal seams, generally known as Coalbed Methane (CBM), Coal Mine Methane (CMM) or Coal Seam Gas (CSG), is a major energy source, as it is the primary constituent of natural gas. At the same time, released methane is a potent greenhouse gas (GHG) and a major safety hazard in underground mining operations. Therefore, a considerable effort has been undertaken to develop coal bed methane extraction and utilization technologies that can achieve both environmental and safety benefits. Countries with significant coal reserves and gassy seams, i.e., USA, Australia, Canada, China, India, Poland and Germany have developed mature methodologies and practices to extract, before and during mining, and utilize significant amounts of methane from coal seams. Nevertheless, on a global scale, methane recovery remains untested and many technical and economic challenges require urgent attention. The research presented in this paper, sponsored by the United States Environmental Protection Agency (EPA), is focused on the Zonguldak Basin, the only hard coal region in Turkey. The basin is known to contain very gassy coal seams and consists of three major regions: Armutcuk, Zonguldak and Amasra. Among the three, the Amasra coalfield is considered as the most favorable for CBM recovery, as it comprises of deeper coal seams and where a private company, Hema Enerji A.S. (Hema) is already developing coalbed methane production facilities. This study aims at developing a reservoir model to predict the potential CBM recovery from the CBM-2 well, the only producing CBM well drilled by HEMA Enerji A.S in the Amasra coalfield. History matching was utilized to model the 15-day production data and uncertainty analysis was performed to estimate the optimum values for the reservoir parameters. The produced model yielded an average production rate of 143 m3/day for 10 years. The total amount of CH4 to be produced during this period was 0.53 million m3. Furthermore, the total amount of GHG to be avoided was estimated at 6585 tCO2e.

Aug 1, 2013

By M. Bélanger, H. -L. Jacob

"The province of Quebec has a strong tradition in industrial minerals. Ten commodities are produced and the annual total shipments have exceeded $600 million in recent years. Quebec is a world renowned producer of chrysotile, titanium slag, graphite, and ilmenite. Quebec is an important North American producer of mica, talc, and peat moss. This paper reviews the main minerals and commodities that have been the object of exploration or development in recent years, namely graphite, wollastonite, dolomite, and silica. Some of the leading projects concerning magnesium minerals and apatite-ilmenite are described. IntroductionQuebec has a strong tradition in industrial minerals. It goes back to the second half of the 19th century when the first graphite and apatite mines in the Gatineau area and asbestos mines in the Eastern Townships were opened. Since then, more than 25 commodities have been produced in Quebec, making industrial minerals an integral part of the Quebec mineral industry. Today, industrial minerals and building materials count for one third of the total mineral production in Quebec.Present industrial mineral production includes 10 commodities (Table 1). In the last five years, the value of industrial mineral shipments has varied between 500 and 700 millions dollars annually, which represents 20% to 25% of Quebec’s total mineral production. For many years, Quebec has been a major producer of chrysotile and titanium slag, the only producer in eastern North America of mica, graphite and ilmenite, and a leading Canadian producer of talc and peat moss. Quebec also produces, mainly for domestic markets, dolomite, limestone, salt and silica.Quebec’s industrial mineral sector has been quite active in the recent years. Exploration by government geologists and companies has led to the outlining of new deposits, some of which are now in production; others are currently being evaluated. Technical and economic studies are also underway to determine the feasibility of various development projects."

Jan 1, 1999

By J. -P. Lempainen, K. Haavanlammi, K. Valkama

The Outotec nickel matte chloride leaching process is especially suitable for small capacity standalone nickel refineries. The matte is leached with hydrochloric acid and oxygen in multiple steps in atmospheric OKTOP® reactors. Oxygen feed prevents reductive conditions and hydrogen formation in the leaching process. A sufficiently high acid concentration keeps the iron dissolved in the solution. The iron is removed after leaching by precipitation and the pregnant leach solution continues to metals recovery. The metals recovery from the chloride solution is done by solvent extractions, where ammonia is used for pH control. Copper and nickel are stripped from the organic phases into sulphate solutions. Metals can be recovered from the purified solution by conventional electrowinning. Other alternatives are precipitation or hydrogen reduction processes. The ammonium chloride in the solvent extraction raffinate is regenerated into ammonia. The calcium chloride solution from ammonia regeneration is routed to acid regeneration where sulphuric acid is added and ultra-pure gypsum is precipitated. The hydrochloric acid solution from this step is recycled back to leaching. The process yields good overall metal recoveries and expensive

Jan 1, 2014

By Wenbin Zhang, George W. Poling

"Prior or simultaneous addition of ammonium sulphate can, not only enhance the activating effect of hydrosulphide ions on xanthate flotation of malachite but it can also eliminate possible detrimental or depressing effects of excess residual hydrosulphide . Use of relatively inexpensive ammonium sulphate appears to reduce the consumption of the much more expensive sulphidizing agent for optimal flotation recovery INTRODUCTIONOxidized copper minerals float poorly with conventional thiol-type collectors. This is believed to be due to the nonadherent character of the collector coating, which is readily re- moved by particle abrasion. Rosas and Polingr reported emulsion flotation seemed capable of resisting abrasion during the flotation of non-sulphide copper ores. It appears that the most common flotation technique for oxidized copper minerals comprises sulphidization with Na .S and subsequent treatment by sulphydryl collector. The principles of this method are available . Malghan recently reviewed the studies on the role of sodium sulphide in the flotation of oxidized copper, lead and zinc minerals.It is well known that in the sulphidized flotation of malachite, the activation process depends strongly on the concentration of the sulphidizing agent, i.e., insufficient sulphide gives poor recoveries because of inadequate sulphidization; excessive sulphide also causes poor recoveries due to the depressive effect of the residual hydro-sulphide ions in solution. A major difficulty in sulphidization, especially with a varying feed nature, is to establish and maintain the optimum sulphide concentration in solution. In plant practice, vigorous control of sodium sulphide is required and stepwise addition of the reagent is recommended to improve the efficiency of the process. Soto and Laskowskim have found that malachite, depressed by an excess of sulphide ions, can restore its floatability if air or oxygen is introduced to the pulp. They attributed this to the oxidation of the HS - ions on the surface of the mineral. Jones and Woodcockuvi showed that a sulphide ion selective electrode could be used to optimize the conditions (e.g . amount of hydrosulphide, sulphidization time, flotation time) more readily and precisely than existing methods in the flotation of oxidized copper ores."

Jan 1, 1989

By A. Rahimi

The smelting plant at Sarcheshmeh Copper complex commenced working with two reverbatory furnaces, four pierce smith converters, two anode furnace and one holding furnace having a known capacity of 420 metric tons of anodic copper according to the initial design in 1982 (1361 Iranian calendar). During the period from the commencement date up until now, the smelting plant has undergone changes for improvement and enhanced production by substituting holding furnace with another anode furnace, installing the fifth converter and utilizing oxyfuel burners on the ceiling of the reverberatory furnaces. According to the different operational processes in reverberatory, converter and anode furnaces different types of corrosion mechanisms and degradation can be observed in the refractories of copper smelting furnaces. In the case of reverberatory furnaces, the corrosion and degradation of refractories may be factors such as hot corrosion by melt, corrosion attack by the constituents of burning fuel, degradation of sidewalk exposed to mechanical stresses of the feed charge and the hydrostatic pressure exerted by the melt inside the furnace, all of which are due to the unique operational condition governing the reverberatory furnaces environment, i.e. burning fuel atmosphere, charge concentration and combination, furnace temperature, calm melt condition, etc. In the case of converter furnaces, the most likely corrosion and degradation of refractories may be due to the chemical reaction between the melt and degradation of tuyere zones due to sever movement of the melt and mechanical strikes of the punch rod. Also the most essential corrosion reaction occurs around the mouth of the converter because of the mechanical strikes by the cleaning device and thermal heat shock. Other parts inside the furnace are corroded due to the reactions between the fayalite slag and the furnace refractory. In anode furnaces the degradation mechanism is mostly related to the gaseous corrosion (penetration of natural gas or liquid gas inside the refractory structure due to the long period of reduction processes and refining stages. Finally another important factor responsible for destruction of refractories in these furnaces is the copper oxide slag together with the fume constituents of burning fuels.

Jan 1, 2004