Search Documents

By Z. Yang, M. J. Collins, N. E. Tuffrey, R. J. Kalanchey, I. M. Masters

The high elevation of China Western Mining Company (WMC)' s Ganhe refinery, and the high iron content of concentrates produced by the WMC mines, were key factors in the selection of pressure leaching by WMC for their new zinc refinery. This paper describes the results of pressure leaching test work conducted by Sherritt in Fort Saskatchewan with a sample of WMC concentrate from Qinghai Province in China. Results from batch pressure leach tests and a four-day pilot plant campaign are reported. The pilot plant campaign included continuous operation of a two-stage pressure leach circuit, as well as neutralization and iron removal steps, resulting in the production of iron-free zinc sulphate solution. Greater than 98% zinc extraction was achieved in pressure leaching, while producing solution containing about 9 g/L H2SO4 and 2 g/L Fe. Following neutralization and iron removal, the solution contained about 170 g/L Zn and less than 10 mg/L Fe. Overall recovery of sulphur in the zinc concentrate feed to elemental sulphur byproduct was about 85%, while 75 to 80% of the indium in the feed was recoverable from the neutralization residue. The test results highlighted the technical and economic advantages offered by the Sherritt Zinc Pressure Leach Process and provided the required data for the engineering design.

Jan 1, 2008

By H. G. Wang

The production process of a coal mine can often be interrupted by all kinds of events scheduled or unscheduled and thus often needs gas drainage for a temporary or long-term sealed area. Gas drainage has a relatively high risk, therefore attention must be paid to its design to keep the process safe. Based on the conservation laws of mass and constituents, and under the conditions of the allowable gas concentration limit in the return air route, the relationship between gas concentration and gas drainage flow rate as a function of time during the drainage process is discussed in detail to build a mathematical model of gas drainage from a sealed area. With respect to the gas drainage process, two different conditions need to be considered: one with a methane free fresh air supply, the other with a low gas concentration. This paper presents the derived mathematical models for these situations and then shows that they can be incorporated into one model with some modification. This combined model can be employed to determine the optimum gas drainage flow rate with the shortest drainage time. The application is coded using the C# programming language within the .NET framework. Finally, the application program developed by the author is used to validate the mathematical model through an example of gas drainage with varying rate.

Aug 1, 2013

By Yugo Mitani, Tatsuya Kato, Chiharu Tokoro, Abdullah Al Mamun

Acid mine drainage (AMD), which is a major source of mining pollution, often contains ferric and/or ferrous ions together with several toxic elements. The ferric and ferrous ions in AMD precipitate in several mineralogical forms after neutralization, and the ferric/ferrous precipitates become the main component of the sludge generated after AMD treatment. The precipitates are also good absorbents for several toxic elements. To avoid generation of voluminous sludges and the re-dissolution of toxic elements from the sludge, it is very important to generate well-draining and efficiently adsorbing sludges by controlling the mineralogical form of the ferric/ferrous precipitates. Green rust, which is ferric and ferrous hydroxide, is a double layer hydroxide which is able to sorb several toxic elements. The green rust transforms to goethite or lepidocrocite by rapid oxidation, whereas it transforms to magnetite at ambient temperature by slow oxidation. The magnetite is also good absorbent especially for toxic cations and it makes a compact sludge due to its magnetic properties. We investigated the magnetite generation process at ambient temperature in detail. The magnetite generation process can be divided into three steps; (i) oxidation of Fe(II), (ii) Fe(II) surface complexation to Fe(III) hydroxide, and (iii) crystallization of magnetite. More magnetite can form when the oxidation rate is slower than the crystallization rate, and optimum conditions for its formation are at pH 9.5 with mild agitation. Ferrihydrite is the most common precipitate and it is able to sorb many different toxic elements. However, it drains badly and its solid/liquid separation properties are poor. We investigated the removal mechanism of several toxic elements by co-precipitation with ferrihydrite. We confirmed that the removal mechanism by co-precipitation partly involved surface precipitation when the initial ratio of toxic elements to ferric ion was high, although the main mechanism was always surface complexation. When surface precipitation occurred, highly efficient toxic element removal with ferrihydrite could be achieved.

Jan 1, 2016

By E. Kouame, M. D. Everell, D. Hodouin, T. Kasongo

"To properly operate a mineral beneficiation plant it is often necessary to have systematic evaluations of the performances of a piece of machinery, of one of the processes or of the plant as a whole. The state of a process can be described from a collection of data: flow-rate values, particle-size distributions and chemical compositions of the various streams of the circuit studied.However, the obtained raw data are generally redundant and inconsistent from a material balance viewpoint, due to natural disturbances, sampling errors, unreliable instrument readouts and laboratory analysis inaccuracies.BILMAT is a computer program which upgrades mineral processing data, adjusting them in a least-squares sense in order that they may verify material conservation constraints. As a consequence, the program is able to calculate the best values of unmeasured flow rates (such as. circulating load ratios). BILMAT is a very general program in the sense that it can accept various data from any type of mineral processing circuit, and its usefulness is demonstrated here for three processing circuits of a pyrochlore concentration plant: grinding, desliming and flotation.IntroductionComputation of the material balance around any metallurgical process, that is the determination of stream flow rates and composition. is a basic step in its evaluation. In spite of the simplicity of the physical laws of mass conservation. and of the very fundamental need to know the flow of components around a process. it appears, particularly in mineral processing. that material balancing is quite often a difficult task. The reasons for this involve the problems associated with collecting measurements in mineral dressing plants. They are generally poorly instrumented and invariably data must be collected through hand sampling. Due to the heterogeneous nature of the streams, segregation occurs and samples are often not adequately representative, a problem made worse by the lack of circuit sampling facilities, which are often completely ignored by plant designers. Furthermore, the nature of the measurements to be performed (for instance particle size distributions in the fine range) frequently gives inaccurate results."

Jan 1, 1981

By D. R. Schmitt, Q. Jia, R. Kofman

"Tests were carried out on clear glass blocks containing borehole aligned with and at an angle to applied principal stress states in order to study the growth of drilling induced tensile fractures. The samples were illuminated such that photoelastic fringes could be video recorded during the measurements; this was useful in assessing states of stress and in determining fracture initiation. Axial drilling induced fractures were observed at the azimuths of the applied uniaxial stress as would be expected from the concentrated stresses. En echelon fractures were observed from the borehole deviated at 45° to the direction of the compression. These preliminary and currently qualitative results show that glass blocks serve as a useful test medium for studies of stress concentration and drilling induced fracture creation. INTRODUCTIONWith the increasing exploitation of unconventional oil/gas reservoirs using deviated drilling in recent years, the effects of the in-situ stress on the success of energy production have become more critical than ever before. Knowledge of the state of stress in the earth enables us to determine well trajectories, well locations, hydraulic fracturing design and production rates, but knowing the crustal stress is always challenging. Strictly, it can only be obtained to varying quantitative degrees by accessing the earth through drilling. Failure of the rock at the borehole wall produces borehole breakouts (e.g., Bell & Gough, 1979; Haimson & Herrick, 1986; Zoback et al., 1985) and drilling-induced tensile fractures (DITF) (e.g., Aadnoy, 1990; Aadnoy & Bell, 1998; Barton et al., 1997; Brudy & Zoback, 1999; Davatzes & Hickman, 2010; Peska & Zoback, 1995). Thus, it is important to understand the failure mechanism of the rock in the vicinity of the borehole. A number of closed-form expressions have been developed that allow the stress concentrations to be calculated in the vicinity of a borehole including Kirsch’s (1898) 2-D plane strain solution and 3D formulae for elastically isotropic (Hiramatsu and Oka, 1962) and anisotropic (Lekhnitskii, 1981; Amadei, 1983) continua. These solutions have been applied in numerous studies (e.g., Ong, 1994; Ong & Roegiers, 1996; Vahid & Ghassemi, 2011; Jia & Schmitt, 2014; Ito et al., 2001) to analyze the failure mechanisms of drilling-induced tensile fractures (DITF) on the borehole wall."

Jan 1, 2015

By Yongjie Bu, Wei Sun, Zhiyong Gao, Yuehua Hu, Hongbiao Tao, Runqing Liu, Central South University

"The flotation behavior of O-isopropyl-N-ethyl thionocarbamate (IPETC) and pH for chalcopyrite and galena was studied through pure mineral test, adsorption quantity determination, solution chemistry calculation and Materials Studio simulation. The results show that the recovery differential value of chalcopyrite and galena is about 20% when pH of the pulp 9.5 and IPETC is 7×10-4 mol/L, the flotability differences of the two minerals is significant. There is competitive adsorption between OH? and IPETC on mineral surfaces, it lead to galena flotability is lower than chalcopyrite flotability. IPETC can remove the hydration layer on mineral surface and adsorb on active sites for collector adsorption, minerals have a better hydrophobicity.INTRODUCTIONCopper and lead are two of the most widely used metals in industrial and living, their applications include building construction, various metal alloys, heat and electricity, machine manufacturing (Zhang et al., 2014). Chalcopyrite and galena are the major source of copper and lead, normally they associated with each other. With the growing use of these resources, high grade and dissemination large particle sizes minerals are less and less, the use of low grade and complex dissemination minerals have to be paid more attention (Chen, Ye, & Li, 2010; Liu, Sun, Hu, & Wang, 2009). As the special properties and complex composition of copper-lead sulfide ore, flotation separation of chalcopyrite from galena effective is a research emphasis and difficulty point in mineral processing (Bruckard, Sparrow, & Woodcock, 2011).In the separation process of chalcopyrite and galena, it is rather important to choose effective collector (Huang, Wang, & Liu, 2014). Enlarging and using the two mineral flotability will be a good basis and start in flotation (Reyes-Bozo et al., 2014). Qin et al. (2013) made a great deal of research on flotation separation of copper/lead concentrate, collector O-isopropyl-N-ethyl thionocarbamate (IPETC), butyl xanthate (BX) and ammonium dibutyl dithiophosphate (ADTP) were investigated, BX and ADTP floated both chalcopyrite and galena well, specific adsorption appeared in the surface of mineral, the problem was the collectors were not selective enough, however IPETC showed better selective."

Jan 1, 2016

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By Jean-Luc Collins

"This paper shows how simple reliability concepts such as mean time between failures and mean repair time can be used efficiently to help increase equipment availability and so reduce the economic losses associated with unreliability.More specifically, the paper shows how these simple concepts can be used in maintaining an appropriate balance between fleet failure and repair rates and how they can be used for setting up priority repair rules f or queuing equipment.IntroductionA profitable mining operation must handle large quantities of ore and waste at the lowest possible cost. To achieve this objective, the operation must optimize the productivity of its fleets of equipment by efficient management of the time element. Figure I shows some basic equipment activities in an open pit operation while Figure 2 shows a tree diagram describing some time elements of these activities.It should be noted that the only time a piece of equipment can generate a profit is when it can be found in the operating status. In order to maximize this time element, the sum of the other time elements must be minimized because the total time is always fixed.This paper shows the application of simple techniques capable of reducing the waiting time for repair (maintenance delay) by using simple reliability concepts."

Jan 1, 1988

By T. Tsutsumi, S. Kukino

"During the diametrical compression test, the tensile stress generated near the loading plate is influenced by the contact area between the loading plates and specimen. However, very few studies have determined the contact area. Theoretical or analytical models have shown that for an orthotropic material (i.e., with material properties that differ along each of three mutually orthogonal twofold axes), the maximum tensile stress is generated at the center of disk when the angle of the principal material direction to the loading direction is close to ?/4. The maximum value is almost constant, regardless of the contact area. Conversely, the maximum tensile stress is generated near the loading plate when the angle between the principal material direction and loading direction is small. The maximum value decreases as the contact area increases. Therefore, in the latter case, the influence of the contact area on tensile strength measurement of is significant.In previous studies, the distribution of stresses applied on the loading plate is assumed to be a uniform load. In reality, the applied stress is highest at the center of loading plate and seems to decrease with distance from center. The applied load disappears at the edge of loading plates. In this study, in order to satisfy this boundary condition on the loading plate, the cosine curve is adopted as the distribution of load applied on the loading plates in a theoretical model of the diametrical compression test. Furthermore, the elastic solution using boundary conditions shown in this study is used to obtain the tensile stress distributions on the loading axis for an orthotropic circular plane. These distributions are compared with empirical results obtained under uniform loading with a loading plate or concentrated loading in previous studies."

Jan 1, 2015

By Mehdi Razavi

Scope of the Study The possibility and risk associated with mining two stopes at the same time The influence of Creighton Fault on the stability and dilution The effect of irregular shape of stope walls on overall stope stability and ore dilution The support requirements for proposed mining plan

Oct 1, 2010

By Jean Dugas, Roger Sirois

The Mineral Deposits Service of the Quebec Department of Natural Resources is engaged in the preparation of metallogenic maps as a contribution to the Canadian Sub-Committee of the Metallogenic Map of North America. The preliminary work is being done on large-scale maps. The main objective is to clearly represent information on ore deposits in a suggestive way. The design of the legend to meet these requirements is discussed. As these maps are still only descriptive, a further step will be the interpretation of data into metallogenic maps with Jess emphasis on the individual deposits and more on the metallogenic factors. Both types of map should prove useful in the search for ore deposits; the first by providing at once a large amount of information, the second by suggesting the ore controls.

Jan 1, 1967

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Abstract-Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-chalcopyrite core - interlayered pyrite-sphalerite-galena (Pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyrite­ quartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone 1) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (Il and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone 1, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F1 fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By J. C. Kurnia

Methane is recognized as one of the prime causes of underground mine disasters around the globe. A cost-effective mine ventilation system and methane control is required to ensure a safe and productive environment in an underground mine whilst keeping energy usage and operating cost at minimum. Typically methane enters a mine environment or tunnel from localized distributed sources at high initial concentration. Hence, an understanding of its dispersion from discrete sources is important to design a methane management system via effective ventilation. This study employs computational fluid dynamics to model methane dispersion in an underground tunnel which has a number of discrete sources of methane and effective ways to dilute and or disperse it. Air flow distribution within the tunnel as well as methane dispersion is simulated by solving the governing transport equations subject to appropriate boundary conditions. First, the effectiveness of ventilation duct placement is examined. Several possibilities are explored and investigated. It is found that the common configuration utilized in underground mine performs best as compared to other configurations in maintaining the concentration of methane below permissible levels. Next, a novel intermittent airflow ventilation system is proposed and evaluated via simulation with the goal of reducing the energy cost whilst maintaining methane level in the mining face below the allowable level. Parametric studies are conducted to investigate effects of various factors influencing the effectiveness and performance of this novel intermittent ventilation system. This study will provide some new ideas for designing an efficient and effective underground mine ventilation system by lowering the net average amount of air that needs to be circulated in the tunnel for a safe operation. KEYWORDS

Aug 1, 2013

By Alessandro Navarra

Discrete event simulation provides a computational framework in which the use of smelting equipment can be analyzed and optimized, leading to the development of alternative modes of operation. Much of the complexity of copper and nickel smelters is centered on the converter aisle. These converters operate in parallel, produce batches, and set the tempo for the downstream operations. In practice, smelter staff schedule daily operations to coordinate the smelting furnaces and converters with downstream operations. Thus, a realistic simulation of smelter operations, over hundreds of days, should incorporate converter scheduling algorithms as presented in this paper.

Jan 1, 2014

By K. Soldenhoff

Mantra Resources Ltd is developing the Mkuju River project is southern Tanzania. The uranium deposit, hosted in ?Karoo? sandstone, is surface outcropping with the majority of uranium mineralisation occurring in the finer clay component of the ore. A flowsheet, consisting of ore beneficiation, acid leaching, RIP uranium recovery and direct precipitation of the uranium product, was developed and successfully demonstrated in continuous mini-plant operations at ANSTO. The selected flowsheet overcomes the difficult slurry rheology, arising from the clay component of the ore, by eliminating the need for a CCD plant. The RIP process was found to contribute to a high uranium extraction, by eliminating ?preg-robbing?, at a relatively low acid addition in leach, with the potential to eliminate ferric ion and oxidant additions.

Aug 1, 2010

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

By G. H. Gale, M. A. F. Fedikow, L. B. Dabek

Abstract-Rare earth element (REE) data are reported for ores, sulfide-bearing rocks and host rocks from massive sulfide deposits and barren sulfide facies iron formations in Proterozoic volcanic rocks of the Flin Flon-Snow Lake area, Manitoba. Some of the rare earth elements (e.g., Eu), are selectively leached in zones of intense alteration and redeposited together with the sulfides and silicates in the uppermost parts of the alteration zones and at the rock-water interface. Chondrite normalized REE profiles of layered sulfide ores and exhalites proximal to the deposits typically have positive europium anomalies and are enriched in light REE. In contrast, barren sulfide facies iron formations exhibit negative or ‘normal’ Eu profiles. REE data are useful to explorationists in determining the presence of ‘off-hole’ metal-bearing sulfide zones, in distinguishing metal-poor sulfidic layers related to ‘economic’ hydrothermal activity from barren sulfide facies iron formation and in some instances as a means of establishing ‘ore-equivalent’ strata.

Jan 1, 1997

By E. V. Konopleva, H. J. McQueen

"The isothermal bainite transformation kinetics of low- and medium-carbon alloy steels after hot deformation and the rmocycling treatment (TC) has been studied by the magneto - metric method. Deformation was produced by rolling at 800°C-1000°C. TC included three cycles of rapid (30°C/s) electro-heating up to 900°C-1000°C followed by quenching.Hot deformation retards bainite transformation in the lower part of bainite range (<400°C) and accelerates it in the upper part (>400°C). The effect is greater for higher strain and lower deformation temperature. Deformation also diminishes the overall bainite fraction below 400°C and increases the completeness of reaction above 400°C.Thermocycling provides more uniform ultrafine austenite grains with average size of 3 µm -4 µm compared to 12 µm -14 µm after conventional heating. The transformation rate after TC was almost the same as after conventional heating in low-carbon steel but was faster in medium-carbon with no change in the completeness of reaction. The degree of acceleration increased with rise of transformation temperature.There are a number of factors which are responsible for a change in bainite transformation kinetics in austenite deformed at high temperatures or subjected to TC. One of the most important factors is the refinement of structure, another one is structural and chemical inhomogenity of austenite due to deformation or to rapid heating. To estimate the contribution of these factors, ?-transformation was studied after different austenitizing conditions (low-temperature heating at 850°C- 950°C; high-temperature heating at 1100°C; step treatment – austenitizing at 1100°C, then cooling to 950°C-850°C). The results obtained make it possible to conclude that the structural and chemical inhomogeneity of austenite activate the bainite reaction while the grain refinement retards it. Intensity of the effect produced by each factor depends strongly on the steel composition."

Jan 1, 1997

By Toivo Toivanen

The paper begins with a brief history of the nickel industry in Finland, and then deals with the introduction of the flash smelting process. The main part of the paper is devoted to nickel refining, which is studied under four main headings -grinding, leaching, electrolyte precipitation, and nickel electrowinning. Flowsheets are illustrated, and the equipment used is described. Analyses of the material in the various stages, from concentrate to high-grade nickel matte, are also presented. N ICKEL made its appearance in the Finnish mining industry forty years ago, when a nickel deposit was discovered at Petsamo in Lapland. Mond Nickel Co. received the concession for this deposit from the Finnish Government, and the Petsamon Nikkeli Company constructed a mine and a nickel smelter (1), the completion of which was prevented by the 1939 Winter War. The mine and smelter were, however, completed soon afterwards in spite of World War II,

Jan 1, 1964

By P. Choquet, F. Miller

"The development and testing of a simple low-cost gauge for measurement of tension in a cable bolt grouted in a borehole are presented. Its principle is based on a resistance wire which is wound on a 70 cm length into the spiral grooves of the wire strand cable bolt. Readings are then taken by a robust automatic data logger with a several day autonomy or by a portable readout. In order to have a complete profile of tension along the cable bolt, a number of tension gauges can be installed along its length.This paper provides a description of the development and laboratory calibration of the tension gauge and addresses the two modes of loading for a cable bolt in a rock mass, namely pure tension and shearing at a joint location.In the second part of the paper, four field tests in underground and open pit mines are reported. The first test was used to substantially modify both the gauge and the readout unit principles while the other tests which are still on-going show a very satisfactory behaviour of the modified version of the tension gauge. IntroductionCable-bolting is often used as ground support in Canadian mines for a variety of applications. In underground mines, cable bolts can be installed vertically at the back of cut and fill stopes or in an inclined fashion in the walls of large open stopes. Alternatively, cable bolts at Mines Gaspe (Noranda Inc.) are used in a fan-shaped pattern from a drill drift to stabilize the inclined roof in 25 m wide open stapes. This new application oriented our research efforts toward the design of a novel instrumentation to monitor the efficiency of most commonly used 5/8-inch cable bolts."

Jan 1, 1988